Boot of Technicolor TG582N with OpenWRT

gistfile1.txt

HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN


CFE version 1.0.37-110.11 for BCM96328 (32bit,SP,BE)
Build Date: å 5月  3 13:29:53 CST 2012 (root@localhost.localdomain)
Copyright (C) 2000-2009 Broadcom Corporation.

HS Serial flash device: name EN25P128, id 0x1c18 size 16384KB
Total Flash size: 16384K with 256 sectors
Light all CPU's LEDs for LED Test.
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000

Board IP address                  : 192.168.2.50:ffffff00  
Host IP address                   : 192.168.2.13  
Gateway IP address                : 192.168.2.254  
Run from flash/host (f/h)         : f  
Default host run file name        : firmware.bin  
Default host flash file name      : bcm963xx_fs_kernel  
Boot delay (0-9 seconds)          : 3  
Board Id (0-5)                    : 963281TAN  
Number of MAC Addresses (1-32)    : 11  
Base MAC Address                  : 00:00:36:11:22:33  
PSI Size (1-64) KBytes            : 24  
Enable Backup PSI [0|1]           : 0  
System Log Size (0-256) KBytes    : 0  
Main Thread Number [0|1]          : 0  

*** Press any key to stop auto run (3 seconds) ***
Auto run second count down: 33210
Booting from only image (0xb8010000) ...
Code Address: 0x80A00000, Entry Address: 0x80a00000
LZMA: Prossible old LZMA format, trying to decompress..
Decompression OK!
Entry at 0x80a00000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80a00000
[    0.000000] Linux version 3.18.20 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46450) ) #1 Fri Sep 4 15:12:19 CEST 2015
[    0.000000] Detected Broadcom 0x6328 CPU revision b0
[    0.000000] CPU frequency is 320 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] board_bcm963xx: Boot address 0xb8000000
[    0.000000] board_bcm963xx: CFE version: 1.0.37-110.11
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0002a075 (Broadcom BMIPS4350)
[    0.000000] board: board name: 963281T_TEF
[    0.000000] MIPS: machine is ADB P.DG A4001N1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 59908K/65536K available (2805K kernel code, 139K rwdata, 464K rodata, 1320K init, 192K bss, 5628K reserved)
[    0.000000] NR_IRQS:256
[    0.000000] Calibrating delay loop... 319.74 BogoMIPS (lpj=639488)
[    0.040000] pid_max: default: 32768 minimum: 301
[    0.044000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.048000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.060000] NET: Registered protocol family 16
[    0.296000] registering PCI controller with io_map_base unset
[    0.316000] PCI host bridge to bus 0000:00
[    0.320000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x10ffffff]
[    0.324000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.328000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.332000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.336000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
[    0.340000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
[    0.344000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.348000] pci 0000:00:00.0:   bridge window [mem 0x10f00000-0x10ffffff]
[    0.352000] Switched to clocksource MIPS
[    0.356000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[    0.364000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[    0.368000] bcma: bus0: Found chip with id 43227, rev 0x00 and package 0x08
[    0.376000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x25, class 0x0)
[    0.384000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x1E, class 0x0)
[    0.392000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x12, class 0x0)
[    0.400000] bcma: bus0: Core 3 found: SDIO Device (manuf 0x4BF, id 0x829, rev 0x07, class 0x0)
[    0.420000] bcma: bus0: Bus registered
[    0.424000] NET: Registered protocol family 2
[    0.432000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.440000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.444000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.452000] TCP: reno registered
[    0.456000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.464000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.468000] NET: Registered protocol family 1
[    0.476000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.484000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.492000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.500000] msgmni has been set to 117
[    0.504000] io scheduler noop registered
[    0.508000] io scheduler deadline registered (default)
[    0.516000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36, base_baud = 1562500) is a bcm63xx_uart
[    0.528000] console [ttyS0] enabled
[    0.528000] console [ttyS0] enabled
[    0.532000] bootconsole [early0] disabled
[    0.532000] bootconsole [early0] disabled
[    0.544000] m25p80 spi1.0: unrecognized JEDEC id 1c3018
[    0.588000] b53_common: found switch: BCM63xx, rev 0
[    0.592000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.604000] TCP: cubic registered
[    0.608000] NET: Registered protocol family 17
[    0.612000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.624000] Bridge firewalling registered
[    0.628000] 8021q: 802.1Q VLAN Support v1.8
[    0.644000] VFS: Cannot open root device "mtdblock2" or unknown-block(0,0): error -6
[    0.652000] Please append a correct "root=" boot option; here are the available partitions:
[    0.660000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    0.660000] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

Boa tarde Pedro, reparei que tentas-te colocar o openwrt no TG582n, também estou a tentar , mas na wiki do openwrt o link para obootloader esta em baixo, ainda possuis uma copia do bootloader que possas partilhar?

Obrigado, cumprimentos.