Lightpack 开源破车
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
/* | |
* Arduino interface for the use of WS2812 strip LEDs | |
* Uses Adalight protocol and is compatible with Boblight, Prismatik etc... | |
* "Magic Word" for synchronisation is 'Ada' followed by LED High, Low and Checksum | |
* @author: Wifsimster <wifsimster@gmail.com> | |
* @library: FastLED v3.001 | |
* @date: 11/22/2015 | |
*/ | |
#include <FastLED.h> | |
#define NUM_LEDS 50 // 设置灯珠总数(貌似不能超过 400 个 | |
#define DATA_PIN A15 // 设置 DATA 引脚的连接位置 | |
// Baudrate, higher rate allows faster refresh rate and more LEDs (defined in /etc/boblight.conf) | |
#define serialRate 115200 | |
// Adalight sends a "Magic Word" (defined in /etc/boblight.conf) before sending the pixel data | |
uint8_t prefix[] = {'A', 'd', 'a'}, hi, lo, chk, i; | |
// Initialise LED-array | |
CRGB leds[NUM_LEDS]; | |
void setup() { | |
// Use NEOPIXEL to keep true colors | |
FastLED.addLeds<NEOPIXEL, DATA_PIN>(leds, NUM_LEDS); | |
// Initial RGB flash | |
LEDS.showColor(CRGB(255, 0, 0)); | |
delay(500); | |
LEDS.showColor(CRGB(0, 255, 0)); | |
delay(500); | |
LEDS.showColor(CRGB(0, 0, 255)); | |
delay(500); | |
LEDS.showColor(CRGB(0, 0, 0)); | |
Serial.begin(serialRate); | |
// Send "Magic Word" string to host | |
Serial.print("Ada\n"); | |
} | |
void loop() { | |
// Wait for first byte of Magic Word | |
for(i = 0; i < sizeof prefix; ++i) { | |
waitLoop: while (!Serial.available()) ;; | |
// Check next byte in Magic Word | |
if(prefix[i] == Serial.read()) continue; | |
// otherwise, start over | |
i = 0; | |
goto waitLoop; | |
} | |
// Hi, Lo, Checksum | |
while (!Serial.available()) ;; | |
hi=Serial.read(); | |
while (!Serial.available()) ;; | |
lo=Serial.read(); | |
while (!Serial.available()) ;; | |
chk=Serial.read(); | |
// If checksum does not match go back to wait | |
if (chk != (hi ^ lo ^ 0x55)) { | |
i=0; | |
goto waitLoop; | |
} | |
memset(leds, 0, NUM_LEDS * sizeof(struct CRGB)); | |
// Read the transmission data and set LED values | |
for (uint8_t i = 0; i < NUM_LEDS; i++) { | |
byte r, g, b; | |
while(!Serial.available()); | |
r = Serial.read(); | |
while(!Serial.available()); | |
g = Serial.read(); | |
while(!Serial.available()); | |
b = Serial.read(); | |
leds[i].r = r; | |
leds[i].g = g; | |
leds[i].b = b; | |
} | |
// Shows new values | |
FastLED.show(); | |
} |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment