ir transmitter for samsung tv q9 and sven 5.1 audio; led highlight under couch

ir_led.esphome.yaml

esphome:
  name: esp_living_couch1
  platform: ESP8266
  board: d1_mini
wifi:
  ssid: "grove"
  password: "0My%Secur"

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "Esp Irda Led Fallback Hotspot"
    password: "KE7ShI8Rwk8b"

captive_portal:

# Enable Home Assistant API
api:
  services:
    - service: mhz19_calibrate_zero
      then:
        - mhz19.calibrate_zero: sensor_mhz19

ota:

#
# IR Sound Speaker controller

remote_receiver:
  pin: 
    number: D4
    inverted: True
    mode: INPUT_PULLUP
  dump: all
  # tolerance: 25%
  # filter: 15us
  # idle: 15ms

remote_transmitter:
  pin: D5
  # Infrared remotes use a 50% carrier signal
  carrier_duty_percent: 50%

# binary_sensor:
#   - platform: remote_receiver
#     name: "Sound Toggle Mute"
#     lg:
#       data: 0x827DB847
#       nbits: 32
switch:
  - platform: template
    name: living_speakers_toggle_mute
    turn_on_action:
      remote_transmitter.transmit_pioneer:
        rc_code_1: 0x821D

  - platform: template
    name: living_speakers_setup
    turn_on_action:
      then:
        - remote_transmitter.transmit_pioneer:
            rc_code_1: 0x8206 # input
        - remote_transmitter.transmit_pioneer:
            rc_code_1: 0x8219 # stereo -> 5.1
        - remote_transmitter.transmit_pioneer:
            rc_code_1: 0x8205 # menu
        - remote_transmitter.transmit_pioneer:
            rc_code_1: 0x8205 # menu
        - remote_transmitter.transmit_pioneer:
            rc_code_1: 0x8205 # menu -> Surround volume
        - remote_transmitter.transmit_pioneer:
            rc_code_1: 0x821E # Up
        - remote_transmitter.transmit_pioneer:
            rc_code_1: 0x821E # Up
        - remote_transmitter.transmit_pioneer:
            rc_code_1: 0x821E # Up
        - remote_transmitter.transmit_pioneer:
            rc_code_1: 0x821E # Up

#
# Couch button

binary_sensor:
  - platform: gpio
    pin: 
      number: D1
      inverted: yes
      mode: INPUT_PULLUP
    name: living_couch_btn
    
    filters:
      - delayed_on:  50ms
      - delayed_off: 50ms
    
    on_click:
      - max_length: 400ms
        min_length: 50ms
        then:
          # - homeassistant.service:
          #     service: media_player.media_play_pause
          #     data:
          #       entity_id: media_player.q9
          - homeassistant.event:
              event: esphome.living_couch_btn_click

      - min_length:  500ms # on_hold
        max_length: 5000ms
        then:
          - remote_transmitter.transmit_pioneer:
              rc_code_1: 0x821D
    
    on_double_click:
      then:
        - homeassistant.event:
            event: esphome.living_couch_btn_dblclick
        # - homeassistant.service:
        #     service: switch.toggle
        #     data:
        #       entity_id: switch.living_toggle_tv

    # on_double_click:
    #   then:
    #     - homeassistant.service:
    #         service: media_player.toggle
    #         data:
    #           entity_id: media_player.q9

    # on_multi_click:
    # - timing:
    #   - ON for at most 0.3s
    #   - OFF for at most 0.3s
    #   - ON for at most 0.3s
    #   - OFF for at least 0.1s
    #   then:
    #     - remote_transmitter.transmit_samsung:
    #         data: 0xE0E06798 # toggle power
    #     # - homeassistant.service:
    #     #     service: media_player.toggle
    #     #     data:
    #     #       entity_id: media_player.q9
    # - timing:
    #   - ON for at most 0.4s
    #   - OFF for at least 0.35s
    #   then:
    #     - remote_transmitter.transmit_pioneer:
    #         rc_code_1: 0x821D



output: # relays
  - platform: esp8266_pwm #gpio
    id: couch_led_mosfet
    pin: D2
light: # frontend to relays
  - platform: monochromatic #binary
    name: living_couch_highlight
    output: couch_led_mosfet


#
# CO2 Sensor

uart: # uart0
  rx_pin: GPIO3 # IO15, IO13 — 2-й вариант физического UART, по-идее можно и основные юзать: TX—GPIO1, RX—GPIO3
  tx_pin: GPIO1
  baud_rate: 9600 # Частота MH-Z19B

# logger использует uart0 по умолчанию
# uart1 может использовать только TX (при необходимости туда можно будет перевесить логгер)
# но проводной логгер не особо нужен, поэтому просто отключаем
logger:
  # Логируем, но толлько через OTA
  baud_rate: 0

sensor:
  - platform: mhz19
    id: sensor_mhz19
    co2:
      name: living_couch_co2
    temperature:
      name: living_couch_internal_temp
    update_interval: 30s
    # В помещении не нужно калибровать каждые 24 часа, 
    # потому что не гарантируется нормальное содержание СО2 (400ppm)
    automatic_baseline_calibration: false