Skip to content

Instantly share code, notes, and snippets.

@acmeplus

acmeplus/miyoo_A30 boot

Created October 9, 2024 20:55
Show Gist options
  • Save acmeplus/ce1d5742efd0333429540c1954674aa7 to your computer and use it in GitHub Desktop.
Save acmeplus/ce1d5742efd0333429540c1954674aa7 to your computer and use it in GitHub Desktop.
Download ZIP
Miyoo A30 - SD CARD full boot to init
Raw
miyoo_A30 boot
HELLO! BOOT0 is starting!
boot0 version : 4.2.0
boot0 commit : ec3a840e24084ed1f604eb32b8f07791ec77ff75
fel_flag = 0x00000000
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
DRAM DRIVE INFO: V1.8
DRAM Type =3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM zq value: 00003bfbDRAM CLK =552 MHZ
ID CHECK VERSION: V0.1
ic use default id
USE PLL DDR1
USE PLL NORMAL
PLL FREQUENCE = 1104 MHZ
DRAM master priority setting ok.
Auto calculate timing parameter!
para_dram_tpr0 = 0047214f
para_dram_tpr1 = 01c2294b
para_dram_tpr2 = 00061043
tcl = 6,tcwl = 4
DRAM TIMING PARA0 = 0b0e180b
DRAM TIMING PARA1 = 0003040f
DRAM TIMING PARA2 = 0406050a
DRAM TIMING PARA3 = 0000400c
DRAM TIMING PARA4 = 05020405
DRAM TIMING PARA5 = 05050403
DRAM TIMING PARA8 = 90003310
DRAM PHY INTERFACE PARA = 02040102
DRAM VTC is disable
DRAM dynamic DQS/DQ ODT is on
DRAM SIZE AUTO SCAN ENABLE.
NOW,the work mode register value is 004318e5
DRAM DQS gate is open.
DRAM two rank training is on,the value is 93003587
DRAM training error,PGSR0 = 9040005f
DRAM low 8 DQs information,DXnGSR = 023f9e80
DRAM high 8 DQs information,DXnGSR = 023d9e80
DRAM do not have two rank,NOW set one rank
DRAM recovery DQS gate mode 0
DRAM DQS gate is close.
DRAM work mode register value = 004318e4
DRAM SIZE =512 M
set one rank ODTMAP
DRAM simple test OK.
dram size =512
Reg pull reg_val=0x00005150,read=0x00005150
read CCM_AHB1_RST_REG0[0x00004040]
read CCM_AHB1_RST_REG0[0x00004040]
read enable CCM_AHB1_RST_REG0[0x00104040]
read s CCM_AHB1_GATE0_CTRL[0x00104040]
SPI clock source :0x23c34600
spi spic->sclk =0x03404c2e
spic_set_clk:mclk=0x03404c2e
Succeed in reading Boot1 file head.
The size of uboot is 00090000.
Ready to disable icache.
Jump to secend Boot.
[ 0.407]
U-Boot 2011.09-rc1-00000-gd7d6afeaa-dirty (Apr 26 2024 - 22:18:20) Allwinner Technology
[ 0.417]version: 1.1.0
[ 0.419]uboot commit : d7d6afeaaeaf434a19e1135b67e44255d17b5ce2
[ 0.426]pmbus: normal or secure os
ready
[ 0.430]PMU: AXP221
[ 0.433]PMU: AXP22x found
bat_vol=0, ratio=100
[ 0.438]PMU: dcdc3 1200
[ 0.441]PMU: pll1 1008 Mhz,PLL6=600 Mhz
AXI=336 Mhz,AHB=200 Mhz, APB1=100 Mhz
dcdc1_vol = 3000
dcdc2_vol = 1100
dcdc3_vol = 1200
dcdc4_vol = 0
dcdc5_vol = 1500
aldo2_vol = 2500
aldo3_vol = 3000
dldo2_vol = 3300
find power_sply to end
vbus exist
no battery, limit to dc
fel key new mode
run key detect
fel_key_mode:0
no key input
dram_para_set start
dram_para_set end
[ 0.567]DRAM: 512 MiB
relocation Offset is: 1e21f000
save config for small mem_size
board.c 661
workmode = 0
flash size =16 M
sunxi spinor is initing...
Reg pull reg_val=0x5150,read=0x5150
read CCM_AHB1_RST_REG0[0x4040]
read CCM_AHB1_RST_REG0[0x4040]
read enable CCM_AHB1_RST_REG0[0x104040]
read s CCM_AHB1_GATE0_CTRL[0x104040]
SPI clock source :0x23c34600
spi spic->sclk =0x51be56d
spic_set_clk:mclk=0x51be56d
sunxi spi init OK
spinor id:0x1840ef
spinor size:0x8000
spi_freq = 80000000
[ 0.661]sunxi flash init ok
fail to find part named env
Using default environment
In: serial
Out: serial
Err: serial
flash size =16 M
the flash size is 16 MB
--------fastboot partitions--------
mbr not exist
base bootcmd=sunxi_flash nor_read 40008000 0 2900;bootm 400a8000
no misc partition is found
bootcmd set setargs_nor
to be run cmd=sunxi_flash nor_read 40008000 0 2900;bootm 400a8000
sunxi_serial: sn_filename is not exist
serial is: 2867973871c3ffffd28a
check kernel/rootfs on sdcard
[ 0.707][mmc]: mmc driver ver 2018-06-25 14:21:00
[ 0.712][mmc]: get sdc_phy_wipe fail.
[ 0.716][mmc]: get sdc0 sdc_erase fail.
[ 0.720][mmc]: get sdc_f_max fail,use default 50000000Hz
[ 0.725][mmc]: get sdc_ex_dly_used fail,use default dly
[ 0.731][mmc]: SUNXI SD/MMC: 0
[ 0.735][mmc]: mmc_config_clock: clk 400000
[ 0.743][mmc]: *Try SD card 0*
[ 0.752][mmc]: mmc_config_clock: clk 25000000
[ 0.757][mmc]: mmc_config_clock: clk 25000000
[ 0.762][mmc]: mmc_config_clock: clk 50000000
[ 0.766][mmc]: CID 0x27504853 0x44363447 0x60da6b79 0x8101778f
[ 0.772][mmc]: mmc clk 50000000
[ 0.775][mmc]: SD/MMC Card: 4bit, capacity: 59344MB
[ 0.780][mmc]: boot0 capacity: 0KB,boot1 capacity: 0KB
[ 0.786][mmc]: ***SD/MMC 0 init OK!!!***
[ 0.791][mmc]: erase_grp_size:0x1WrBlk * 0x200 = 0x200 Byte
[ 0.796][mmc]: secure_feature 0x0
[ 0.800][mmc]: secure_removal_type 0x0
reading uimage
reading rootfs.ramfs
uimage/rootfs loaded, change cmd
WORK_MODE_BOOT
board_status_probe
[ 1.256]key trigger
startup status = 0
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
====== pressed count=5, g_power_key=1
POWER LED:ON
lcd_used = 1
lcd_bl_en: name=, port=0, port_num=0, mul_sel=0, pull=0, drv_level=0, data=0, gpio=0
smcl's set manager is NULL
<axp22, dc1sw>
power cause: 0
boot
sunxi_bmp_logo_display
bmp_info.buffer = 5f000000
decode bmp ok
begin to set framebuffer
screen_id =0, screen_width =480, screen_height =640
frame buffer address 5f001000
begin to show layer
bmp display finish
addr = 5f000000
### main_loop entered: bootdelay=0
[ 2.027]Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at 40008000 ...
Image Name: ARM OpenWrt Linux-3.4.39
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3764264 Bytes = 3.6 MiB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum ... OK
XIP Kernel Image ... OK
OK
para err in disp_ioctl, cmd = 0xa,screen id = 1
[ 2.093][mmc]: MMC Device 2 not found
[ 2.097][mmc]: mmc ????????????????^ not find,so not exit
force sunxi spinor exit
dma 0x5eb99a6c int is not used yet
dma 0x5eb99a6c int is free, you do not need to free it again
dma 0x5eb99a88 int is not used yet
dma 0x5eb99a88 int is free, you do not need to free it again
reload config to 0x43000000
[ 2.104]
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Linux version 3.4.39 (alfchen@alfchen-NUC) (gcc version 6.4.1 (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) ) #1053 SMP PREEMPT Sat Apr 27 03:48:45 UTC 2024
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: sun8i
[ 0.000000] Initialized persistent memory from 43080800-430907ff
[ 0.000000] cma: CMA: reserved 128 MiB at 58000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] On node 0 totalpages: 131072
[ 0.000000] free_area_init_node: node 0, pgdat c0848d40, node_mem_map c0893000
[ 0.000000] Normal zone: 1152 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 129920 pages, LIFO batch:31
[ 0.000000] script_init enter!
[ 0.000000] script_init exit!
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c0d27000 s6592 r8192 d13888 u32768
[ 0.000000] pcpu-alloc: s6592 r8192 d13888 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: boot_type=3 disp_para=100 fb_base=0x5f000000 config_size=40960 boot.serialno=2867973871c3ffffd28a boot.hardware=sun8i console=ttyS1,115200 rootfstype=ramfs rw init8
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 512MB = 512MB total
[ 0.000000] Memory: 363504k/363504k available, 160784k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0701000 (7140 kB)
[ 0.000000] .init : 0xc0701000 - 0xc072d9c0 ( 179 kB)
[ 0.000000] .data : 0xc072e000 - 0xc0849a80 (1135 kB)
[ 0.000000] .bss : 0xc084a900 - 0xc0892c34 ( 289 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:416
[ 0.000000] Architected local timer running at 24.00MHz.
[ 0.000000] Switching to timer-based delay loop
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000186] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000)
[ 0.000206] pid_max: default: 4096 minimum: 301
[ 0.000339] Security Framework initialized
[ 0.000415] Mount-cache hash table entries: 512
[ 0.001241] CPU: Testing write buffer coherency: ok
[ 0.001467] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.001479] [sunxi_smp_prepare_cpus] enter
[ 0.001514] Setting up static identity map for 0x405c4798 - 0x405c47f0
[ 0.006194] CPU1: Booted secondary processor
[ 0.006258] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.010000] CPU2: Booted secondary processor
[ 0.010000] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.010327] CPU3: Booted secondary processor
[ 0.010327] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.010439] Brought up 4 CPUs
[ 0.010439] SMP: Total of 4 processors activated (19200.00 BogoMIPS).
[ 0.014722] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.014842] pinctrl core: initialized pinctrl subsystem
[ 0.024919] NET: Registered protocol family 16
[ 0.025807] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[ 0.025807] script_sysfs_init success
[ 0.025807] sunxi_dump_init success
[ 0.025807] gpiochip_add: registered GPIOs 0 to 383 on device: sunxi-pinctrl
[ 0.025807] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver
[ 0.025807] gpiochip_add: registered GPIOs 1024 to 1031 on device: axp-pinctrl
[ 0.025807] persistent_ram: uncorrectable error in header
[ 0.025807] persistent_ram: no valid data in buffer (sig = 0xffffffff)
[ 0.034144] console [ram-1] enabled
[ 0.034574] [sunxi-module]: [sunxi-module.0] probe success
[ 0.034720] script config pll3 to 297 Mhz
[ 0.034936] script config pll4 to 300 Mhz
[ 0.035072] script config pll6 to 600 Mhz
[ 0.035191] script config pll8 to 408 Mhz
[ 0.035410] script config pll9 to 480 Mhz
[ 0.035529] script config pll10 to 297 Mhz
[ 0.035916] sunxi_default_clk_init
[ 0.036125] try to set pll6ahb1 to 200000000
[ 0.036283] try to set ahb clk source to pll6ahb1
[ 0.036398] set ahb clk source to pll6ahb1
[ 0.036610] try to set ahb1 to 200000000
[ 0.036728] try to set apb1 to 100000000
[ 0.070242] bio: create slab <bio-0> at 0
[ 0.070589] [ARISC] :sunxi-arisc driver v1.02
[ 0.084896] [ARISC] :arisc version: [v0.1.33]
[ 0.091602] [ARISC] :sunxi-arisc driver v1.02 startup succeeded
[ 0.091820] pwm module init!
[ 0.093202] SCSI subsystem initialized
[ 0.093202] usbcore: registered new interface driver usbfs
[ 0.093202] usbcore: registered new interface driver hub
[ 0.093202] usbcore: registered new device driver usb
[ 0.093202] twi_chan_cfg()348 - [twi0] has no twi_regulator.
[ 0.093202] twi_chan_cfg()348 - [twi1] has no twi_regulator.
[ 0.093202] twi_chan_cfg()348 - [twi2] has no twi_regulator.
[ 0.093202] Linux video capture interface: v2.00
[ 0.093202] [axp22_init_chip] read axp22 ic type=0x6
[ 0.100399] current_limit = 1200000
[ 0.100605] Advanced Linux Sound Architecture Driver Version 1.0.25.
[ 0.101098] cfg80211: Calling CRDA to update world regulatory domain
[ 0.102070] Switching to clocksource arch_sys_counter
[ 0.102220] FS-Cache: Loaded
[ 0.102220] CacheFiles: Loaded
[ 0.105919] hci: ERR: get ehci1 abh clk failed.
[ 0.106040] hci: ERR: clock_init failed
[ 0.106262] hci: ERR: get ohci1 abh clk failed.
[ 0.106376] hci: ERR: clock_init failed
[ 0.107746] NET: Registered protocol family 2
[ 0.108211] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.108835] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.109285] TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
[ 0.109665] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.109877] TCP: reno registered
[ 0.110295] NET: Registered protocol family 1
[ 0.110709] Unpacking initramfs...
[ 0.110828] Initramfs unpacking failed: junk in compressed archive
[ 0.126311] Freeing initrd memory: 15360K
[ 0.126953] [pm]aw_pm_init!
[ 0.127073] standby_mode = 1.
[ 0.127187] wakeup src cnt is : 2.
[ 0.127401] [exstandby]leave extended_standby_enable_wakeup_src : event 0x800000
[ 0.127517] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_map 0x80
[ 0.127730] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_group 0x0
[ 0.127945] [exstandby]leave extended_standby_enable_wakeup_src : event 0x800000
[ 0.128062] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_map 0x280
[ 0.128274] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_group 0x0
[ 0.128511] sunxi_reg_init enter
[ 0.129160] audit: initializing netlink socket (disabled)
[ 0.129409] type=2000 audit(0.120:1): initialized
[ 0.130738] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.131010] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.131431] msgmni has been set to 995
[ 0.132752] io scheduler noop registered
[ 0.132873] io scheduler deadline registered
[ 0.133048] io scheduler cfq registered (default)
[ 0.133275] [DISP]disp_module_init
[ 0.134386] OSAL_Pwm_Config pwm 0, <19531 / 100000> , ret = 0
[ 0.134870] ret:0,fb_base:0x5f000000
[ 0.135140] [DISP] parser_disp_init_para,line:184: fetch script data disp_init.screen2_output_type fail
[ 0.135465] [DISP] parser_disp_init_para,line:201: fetch script data disp_init.screen2_output_mode fail
[ 0.135688] fb0_format 0
[ 0.135896] scaler_mode 0
[ 0.136009] fb_width 1e0
[ 0.136121] fb_height 280
[ 0.136240] [DISP] parser_disp_init_para,line:266: fetch script data disp_init.fb2_format fail
[ 0.136563] [DISP] parser_disp_init_para,line:271: fetch script data disp_init.fb2_scaler_mode_enable fail
[ 0.136885] [DISP] parser_disp_init_para,line:276: fetch script data disp_init.fb2_width fail
[ 0.137207] [DISP] parser_disp_init_para,line:281: fetch script data disp_init.fb2_height fail
[ 0.142862] [fb_map_boot_logo]w=480,h=640,phy_addr=0x5f001000, vir_addr=0xe086b000
[ 0.150663] set registered_fb[0] to 480x640
[ 0.150992] set registered_fb[1] to 480x640
[ 0.151215] set registered_fb[2] to 480x640
[ 0.151443] set registered_fb[3] to 480x640
[ 0.151763] set registered_fb[4] to 480x640
[ 0.151992] set registered_fb[5] to 480x640
[ 0.152213] set registered_fb[6] to 480x640
[ 0.152534] set registered_fb[7] to 480x640
[ 0.152972] [DISP]disp_module_init finish
[ 0.153312] sw_uart_get_devinfo()2038 - uart0 has no uart_regulator.
[ 0.153433] sw_uart_get_devinfo()2038 - uart1 has no uart_regulator.
[ 0.154011] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
[ 0.154381] uart1: ttyS1 at MMIO 0x1c28400 (irq = 33) is a SUNXI
[ 0.154596] sw_uart_pm()1296 - uart1 clk is already enable
[ 0.154719] sw_console_setup()1696 - console setup baud 115200 parity n bits 8, flow n
[ 0.250532] console [ttyS1] enabled
[ 0.450996] loop: module loaded
[ 0.647653] [NAND]panic_buff_handle 0xd8588000 ,0x58588000
[ 0.745564] [NAND][NAND]nand init start, nand0_used_flag is 0
[ 0.843718] [NAND]nand_cache_level err! 0[NAND]nand_capacity_level err! 0
[ 1.138293] regisger ISP =====================
[ 1.199854] [NAND]nand driver is disabled
[ 1.204633] no ldo for moto, ignore it
[ 1.208894] no ldo moto voltage config, ignore it
[ 1.214379] sunxi_vibrator init end
[ 1.218526] lradc_fetch_sysconfig_para: used script_get_item err.
[ 1.226265] sunxi_spi_chan_cfg()1389 - [spi-0] has no spi_regulator.
[ 1.234042] spi spi0: master is unqueued, this is deprecated
[ 1.240689] NorFlash ID: 0xef4018 - 0xef40
[ 1.245454] m25p80 spi0.0: found w25q128, expected at25df641
[ 1.251859] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 1.257659] Creating 4 MTD partitions on "(null)":
[ 1.263106] 0x000000000000-0x0000000a0000 : "boot"
[ 1.269274] 0x0000000a0000-0x0000005a0000 : "kernel"
[ 1.275685] 0x0000005a0000-0x000000600000 : "config"
[ 1.281984] 0x000000600000-0x000001000000 : "rootfs"
[ 1.288432] tun: Universal TUN/TAP device driver, 1.6
[ 1.294155] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.301303] RTW: module init start
[ 1.305182] RTW: rtl8188fu v5.11.5.4-0-g65b8f0aad.20220413
[ 1.311481] RTW: build time: Jan 31 2024 16:06:31
[ 1.316859] RTW: rtw_inetaddr_notifier_register
[ 1.322063] usbcore: registered new interface driver rtl8188fu
[ 1.328737] RTW: module init ret=0
[ 1.332625] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.360176] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.369185] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus number 1
[ 1.378247] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000
[ 1.400030] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00
[ 1.406710] ehci_irq: highspeed device connect
[ 1.411961] hub 1-0:1.0: USB hub found
[ 1.416236] hub 1-0:1.0: 1 port detected
[ 1.421020] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.448139] sunxi-ohci sunxi-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 1.456770] sunxi-ohci sunxi-ohci.1: new USB bus registered, assigned bus number 2
[ 1.465412] sunxi-ohci sunxi-ohci.1: irq 105, io mem 0xf1c1a400
[ 1.534375] hub 2-0:1.0: USB hub found
[ 1.538650] hub 2-0:1.0: 1 port detected
[ 1.543450] usbcore: registered new interface driver cdc_acm
[ 1.549931] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.559072] usbcore: registered new interface driver cdc_wdm
[ 1.565469] Initializing USB Mass Storage driver...
[ 1.571085] usbcore: registered new interface driver usb-storage
[ 1.577856] USB Mass Storage support registered.
[ 1.583127] usbcore: registered new interface driver ums-sddr09
[ 1.589926] usbcore: registered new interface driver ums-sddr55
[ 1.596711] usbcore: registered new interface driver usbserial
[ 1.603400] usbserial: USB Serial Driver core
[ 1.608375] usbcore: registered new interface driver option
[ 1.614805] USB Serial support registered for GSM modem (1-port)
[ 1.740041] usb 1-1: new high-speed USB device number 2 using sunxi-ehci
[ 1.891432] RTW:
[ 1.891435] usb_endpoint_descriptor(0):
[ 1.898023] RTW: bLength=7
[ 1.901143] RTW: bDescriptorType=5
[ 1.905019] RTW: bEndpointAddress=81
[ 1.909085] RTW: wMaxPacketSize=512
[ 1.913165] RTW: bInterval=0
[ 1.916467] RTW: RT_usb_endpoint_is_bulk_in = 1
[ 1.921607] RTW:
[ 1.921610] usb_endpoint_descriptor(1):
[ 1.928292] RTW: bLength=7
[ 1.931407] RTW: bDescriptorType=5
[ 1.935283] RTW: bEndpointAddress=2
[ 1.939351] RTW: wMaxPacketSize=512
[ 1.943335] RTW: bInterval=0
[ 1.946633] RTW: RT_usb_endpoint_is_bulk_out = 2
[ 1.951965] RTW:
[ 1.951968] usb_endpoint_descriptor(2):
[ 1.958552] RTW: bLength=7
[ 1.961667] RTW: bDescriptorType=5
[ 1.965637] RTW: bEndpointAddress=3
[ 1.969608] RTW: wMaxPacketSize=512
[ 1.973590] RTW: bInterval=0
[ 1.976886] RTW: RT_usb_endpoint_is_bulk_out = 3
[ 1.982216] RTW: nr_endpoint=3, in_num=1, out_num=2
[ 1.982221]
[ 1.989479] RTW: USB_SPEED_HIGH
[ 1.993172] RTW: CHIP TYPE: RTL8188FU
[ 1.997570] RTW: Chip Version Info: CHIP_8188F_S2_1T1R_RomVer(0)
[ 2.004457] RTW: _ConfigChipOutEP_8188F OutEpQueueSel(0x05), OutEpNumber(2)
[ 2.012561] RTW: EEPROM type is E-FUSE
[ 2.017307] RTW: Boot from EFUSE, Autoload OK !
[ 2.022811] RTW: hal_EfuseSwitchToBank: Efuse switch bank to 0
[ 2.154558] RTW: hal_ReadEFuse_WiFi: data end at address=0x6e
[ 2.161339] RTW: HW EFUSE
[ 2.164568] RTW: 0x000: 29 81 00 FC 0B 00 00 00 00 0C 04 4C 10 07 00 00
[ 2.174483] RTW: 0x010: 2B 2A 2A 2A 29 2E 2D 2D 2D 2D 2D 22 FF FF FF FF
[ 2.184410] RTW: 0x020: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.194426] RTW: 0x030: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.204343] RTW: 0x040: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.214245] RTW: 0x050: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.224164] RTW: 0x060: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.234077] RTW: 0x070: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.243990] RTW: 0x080: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.253904] RTW: 0x090: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.263803] RTW: 0x0A0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.273805] RTW: 0x0B0: FF FF FF FF FF FF FF FF 23 18 24 00 00 00 00 FF
[ 2.283720] RTW: 0x0C0: FF 02 00 10 00 FF 00 FF 00 00 FF FF FF FF FF FF
[ 2.293644] RTW: 0x0D0: DA 0B 79 F1 47 66 40 C8 FE 0F 97 AC 8E 09 03 52
[ 2.303568] RTW: 0x0E0: 65 61 6C 74 65 6B 09 03 38 30 32 2E 31 31 6E 00
[ 2.313479] RTW: 0x0F0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.323380] RTW: 0x100: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.333291] RTW: 0x110: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.343195] RTW: 0x120: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.353202] RTW: 0x130: C1 B6 FF FF FF FF FF FF FF FF 00 11 FF FF FF FF
[ 2.363118] RTW: 0x140: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.373020] RTW: 0x150: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.382937] RTW: 0x160: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.392858] RTW: 0x170: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.402782] RTW: 0x180: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.412708] RTW: 0x190: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.422628] RTW: 0x1A0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.432628] RTW: 0x1B0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.442539] RTW: 0x1C0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.452446] RTW: 0x1D0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.462368] RTW: 0x1E0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.472286] RTW: 0x1F0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[ 2.482219] RTW: EEPROM VID = 0x bda
[ 2.486287] RTW: EEPROM PID = 0xf179
[ 2.490470] RTW: hal_com_config_channel_plan chplan:0x23
[ 2.496472] RTW: Hal_EfuseParsePowerSavingMode_8188F...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(1)
[ 2.508168] RTW: ### PS params=> power_mgnt(2),usbss_enable(0) ###
[ 2.517557] RTW: kfree Pwr Trim flag:1
[ 2.521833] RTW: bb_gain:0
[ 2.528435] RTW: rtl8188f_FirmwareDownload fw: FW_NIC, size: 20832
[ 2.535512] RTW: rtl8188f_FirmwareDownload: fw_ver=f fw_subver=0001 sig=0x88f1, Month=05, Date=06, Hour=09, Minute=34
[ 2.547500] RTW: rtl8188f_FirmwareDownload(): Shift for fw header!
[ 2.554476] RTW: rtl8188f_FirmwareDownload by IO write!
[ 2.592061] RTW: polling_fwdl_chksum: Checksum report OK! (1, 0ms), REG_MCUFWDL:0x00050105
[ 2.602931] RTW: _8051Reset8188: Finish
[ 2.616434] RTW: _FWFreeToGo: Polling FW ready OK! (73, 10ms), REG_MCUFWDL:0x000501c6
[ 2.625336] RTW: rtl8188f_FirmwareDownload: DLFW OK !
[ 2.631059] RTW: rtl8188f_FirmwareDownload success. write_fw:1, 80ms
[ 2.638433] RTW: <=== rtl8188f_FirmwareDownload()
[ 2.645687] RTW: CardDisableRTL8188FU
[ 2.654435] RTW: hal_read_mac_hidden_rpt OK! (1, 10ms), fwdl:1, id:0x19
[ 2.661988] RTW: InitAdapterVariablesByPROM_8188FU(): REPLACEMENT = 0
[ 2.669240] RTW: rtw_hal_read_chip_info in 650 ms
[ 2.674716] RTW: init_channel_set((null)) ChannelPlan ID:0x23, ch num:14
[ 2.682304] RTW: [RF_PATH] ver_id.RF_TYPE:RF_1T1R
[ 2.687723] RTW: [RF_PATH] HALSPEC's rf_reg_trx_path_bmp:0x11, rf_reg_path_avail_num:1, max_tx_cnt:1
[ 2.698070] RTW: [RF_PATH] PG's trx_path_bmp:0x00, max_tx_cnt:0
[ 2.704754] RTW: [RF_PATH] Registry's trx_path_bmp:0x00, tx_path_lmt:0, rx_path_lmt:0
[ 2.713653] RTW: [RF_PATH] HALDATA's trx_path_bmp:0x11, max_tx_cnt:1
[ 2.720819] RTW: [RF_PATH] HALDATA's rf_type:RF_1T1R, NumTotalRFPath:1
[ 2.728266] RTW: rtw_hal_rfpath_init trx_path_bmp:0x11(RF_1T1R), NumTotalRFPath:1, max_tx_cnt:1
[ 2.738134] RTW: [TRX_Nss] HALSPEC - tx_nss:1, rx_nss:1
[ 2.744047] RTW: [TRX_Nss] Registry - tx_nss:0, rx_nss:0
[ 2.750149] RTW: [TRX_Nss] HALDATA - tx_nss:1, rx_nss:1
[ 2.756051] RTW: rtw_hal_trxnss_init tx_nss:1, rx_nss:1
[ 2.762189] RTW: init_mlme_default_rate_set: support CCK
[ 2.768189] RTW: init_mlme_default_rate_set: support OFDM
[ 2.774903] RTW: NR_RECVBUFF: 8, recvbuf_nr: 8
[ 2.779942] RTW: MAX_RECVBUF_SZ: 32768
[ 2.784238] RTW: NR_PREALLOC_RECV_SKB: 8
[ 2.789058] RTW: rtw_alloc_macid((null)) if1, mac_addr:ff:ff:ff:ff:ff:ff macid:1
[ 2.797407] RTW: rtw_init_pwrctrl_priv: IPS_mode=1, LPS_mode=2, LPS_level=0
[ 2.805482] RTW: IQK FW offload:disable
[ 2.809854] RTW: Init_ODM_ComInfo_8188f(): Fv=0 Cv=12
[ 2.815715] RTW: rtw_regsty_chk_target_tx_power_valid return _FALSE for band:0, path:0, rs:0, t:-1
[ 2.825960] RTW: phy_ConfigBBWithPgParaFile(): No File PHY_REG_PG.txt, Load from HWImg Array!
[ 2.835566] RTW: default power by rate loaded
[ 2.840674] RTW: pwrctrlpriv.bSupportRemoteWakeup~~~~~~
[ 2.846575] RTW: pwrctrlpriv.bSupportRemoteWakeup~~~[1]~~~
[ 2.852881] RTW: rtw_macaddr_cfg mac addr:c8:fe:0f:97:ac:8e
[ 2.859171] RTW: bDriverStopped:True, bSurpriseRemoved:False, bup:0, hw_init_completed:0
[ 2.868386] RTW: rtw_cfg80211_init_wiphy_band:rf_type=0
[ 2.874315] RTW: [HT] HAL Support STBC = 0x01
[ 2.879351] RTW: rtw_wiphy_alloc(phy0)
[ 2.883666] RTW: rtw_wdev_alloc(padapter=e0999000)
[ 2.889089] RTW: rtw_wiphy_register(phy0)
[ 2.894110] RTW: rtw_ndev_init(wlan0) if1 mac_addr=c8:fe:0f:97:ac:8e
[ 2.901780] RTW: rtw_ndev_notifier_call(wlan0) state:16
[ 2.908410] RTW: rtw_ndev_notifier_call(wlan0) state:5
[ 2.915038] file system registered
[ 2.920171] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 2.927910] android_usb gadget: Number of LUNs=1
[ 2.933248] lun0: LUN: removable file: (no medium)
[ 2.939062] android_usb gadget: android_usb ready
[ 2.944625] sunxikbd_init failed.
[ 2.949002] sunxi-rtc sunxi-rtc: rtc core: registered sunxi-rtc as rtc0
[ 2.956514] i2c /dev entries driver
[ 3.121177] i2c driver added
[ 3.124564] sunxi cedar version 0.1
[ 3.128679] [cedar]: install start!!!
[ 3.133006] [cedar]: install end!!!
[ 3.137107] sunxi_pwr_key_fetch_sysconfig_para script_parser_fetch "pwr_ctrl" pwr_ctrl_used = -679256216
[ 3.147843] =========script_get_err============
[ 3.156288] axp22_dcdc3: Failed to create debugfs directory
[ 3.165219] sdhci: Secure Digital Host Controller Interface driver
[ 3.172182] sdhci: Copyright(c) Pierre Ossman
[ 3.177096] [mmc]: SD/MMC/SDIO Host Controller Driver(v1.126 2018-10-15 14:05) Compiled in Jan 31 2024 at 16:06:26
[ 3.188766] is sdio=0
[ 3.191452] [mmc]: get mmc0's sdc_power is null!
[ 3.196665] force 2 used=0
[ 3.199754] is sdio=1
[ 3.202359] force 2 sdio=1
[ 3.205520] [mmc]: get mmc2's 2xmode ok, val = 0
[ 3.210730] [mmc]: get mmc2's ddrmode ok, val = 0
[ 3.216032] [mmc]: MMC host used card: 0x5, boot card: 0x0, io_card 4
[ 3.224226] [mmc]: sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 3.237274] [mmc]: sdc2 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 3.249815] no led1_active_low, sunxi_leds_fetch_sysconfig_para failed!
[ 3.257252] =========script_get_err============
[ 3.262444] [led]:sunxi_led_init begin!
[ 3.266780] =====led_sysconfig_para=====.
[ 3.271324] led1 gpio number is 362
[ 3.275347] led1_trigger gpio number is default-on
[ 3.280978] Registered led device: led1
[ 3.285938] usbcore: registered new interface driver usbhid
[ 3.292295] usbhid: USB HID core driver
[ 3.296631] zram: num_devices not specified. Using default: 1
[ 3.303172] zram: Creating 1 devices ...
[ 3.308105] Linux telephony interface: v1.00
[ 3.313697] usbcore: registered new interface driver snd-usb-audio
[ 3.321614] [ audio ] err:try to get audio_pa_en failed !
[ 3.327688] request gpio failed!
[ 3.331458] plugio = 357, enio = 356
[ 3.335592] audio_run_thread
[ 3.335752] [ audio ] err:try to get audio_linein_detect failed!
[ 3.335759] [ audio ] err:try to get usb_detect failed!
[ 3.335765] [ audio ] err:try to get mic_array_led_ctrl failed!
[ 3.337742] codec_set_bias_level,line:2240, SND_SOC_BIAS_STANDBY
[ 3.365094] audio plug io value = 1, oldvalue = -1, audio en expectval=1, val=1
[ 3.375092] asoc: codec-aif1 <-> sunxi-codec mapping ok
[ 3.381201] asoc: codec-aif2 <-> sunxi-codec-aif2-dai mapping ok
[ 3.388168] asoc: codec-aif3 <-> sunxi-codec-aif2-dai mapping ok
[ 3.398433] u32 classifier
[ 3.401614] Actions configured
[ 3.405471] Netfilter messages via NETLINK v0.30.
[ 3.410793] nf_conntrack version 0.5.0 (7967 buckets, 31868 max)
[ 3.417852] ctnetlink v0.93: registering with nfnetlink.
[ 3.423871] IPVS: Registered protocols ()
[ 3.428528] IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
[ 3.436861] IPVS: Creating netns size=840 id=0
[ 3.442003] IPVS: ipvs loaded.
[ 3.445617] IPv4 over IPv4 tunneling driver
[ 3.450714] gre: GRE over IPv4 demultiplexor driver
[ 3.456286] ip_gre: GRE over IPv4 tunneling driver
[ 3.462108] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.468291] TCP: cubic registered
[ 3.472061] Initializing XFRM netlink socket
[ 3.476896] NET: Registered protocol family 17
[ 3.482007] NET: Registered protocol family 15
[ 3.487510] ThumbEE CPU extension supported.
[ 3.492434] Registering SWP/SWPB emulation handler
[ 3.498139] [LCD]lcd_module_init
[ 3.501902] ====== lcd_init
[ 3.505561] =========== default LCD_open_flow 0
[ 3.510810] [LCD]lcd_module_init finish
[ 3.516073] sunxi-rtc sunxi-rtc: setting system clock to 1970-01-01 00:00:25 UTC (25)
[ 3.516929] disp_lcd_set_bright d7a993c0 50
[ 3.516936] OSAL_Pwm_Config -678564864 19922 0
[ 3.516946] OSAL_Pwm_Config pwm 0, <19922 / 100000> , ret = 0
[ 3.516952] disp_lcd_set_bright d7a993c0 50
[ 3.516957] OSAL_Pwm_Config -678564864 19922 0
[ 3.516963] OSAL_Pwm_Config pwm 0, <19922 / 100000> , ret = 0
[ 3.516985] disp_lcd_set_bright d7a993c0 50
[ 3.516990] OSAL_Pwm_Config -678564864 19922 0
[ 3.516996] OSAL_Pwm_Config pwm 0, <19922 / 100000> , ret = 0
[ 3.573773] ths_fetch_sysconfig_para: type err device_used = 1.
[ 3.580983] sunxi_cpu_budget_vftable_init: support only one vf_table
[ 3.588535] CPU Budget:Register notifier
[ 3.592991] CPU Budget:register Success
[ 3.597406] sunxi-budget-cooling sunxi-budget-cooling: Cooling device registered: thermal-budget-0
[ 3.609752] ALSA device list:
[ 3.613249] #0: sndcodec
[ 3.616618] Waiting for root device ...
[ 4.060026] ====codec_init_events===
[ 4.130030] WRN:L2917(drivers/usb/sunxi_usb/udc/sunxi_udc.c):pdev is null
[ 4.225013] [mmc]: mmc 0 detect change, present 1
[ 4.730035] [mmc]: sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.741364] [mmc]: sdc0 power_supply is null
[ 4.760025] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.792354] [mmc]: *** sunxi_mci_dump_errinfo(L977): smc 0 err, cmd 52, RTO !!
[ 4.801568] [mmc]: *** sunxi_mci_dump_errinfo(L977): smc 0 err, cmd 52, RTO !!
[ 4.809940] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.822740] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.834379] *******************Try sdio*******************
[ 4.841453] [mmc]: *** sunxi_mci_dump_errinfo(L977): smc 0 err, cmd 5, RTO !!
[ 4.849648] mmc0: req failed (CMD5): -110, retrying...
[ 4.856268] [mmc]: *** sunxi_mci_dump_errinfo(L977): smc 0 err, cmd 5, RTO !!
[ 4.864544] mmc0: req failed (CMD5): -110, retrying...
[ 4.871163] [mmc]: *** sunxi_mci_dump_errinfo(L977): smc 0 err, cmd 5, RTO !!
[ 4.879437] mmc0: req failed (CMD5): -110, retrying...
[ 4.886056] [mmc]: *** sunxi_mci_dump_errinfo(L977): smc 0 err, cmd 5, RTO !!
[ 4.894330] *******************Try sd *******************
[ 4.901074] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.911473] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.924262] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.951530] [mmc]: sdc0 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.962133] [mmc]: sdc0 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.973934] [mmc]: sdc0 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
[ 4.984407] [mmc]: sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
[ 4.994893] [mmc]: sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B
[ 5.005369] mmc0: new high speed SDXC card at address 5048
[ 5.011914] mmcblk0: mmc0:5048 SD64G 57.9 GiB
[ 5.018490] mmcblk0: p1 p2
[ 5.022214] *******************sd init ok*******************
@acmeplus
Copy link
Author

acmeplus commented Oct 9, 2024 •
edited
Loading

For comparison, here's the boot log for the stock from mtd (without SDCARD)

HELLO! BOOT0 is starting!
boot0 version : 4.2.0
boot0 commit : ec3a840e24084ed1f604eb32b8f07791ec77ff75
 
fel_flag = 0x00000000
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
DRAM DRIVE INFO: V1.8
DRAM Type =3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM zq value: 00003bfbDRAM CLK =552 MHZ
ID CHECK VERSION: V0.1
ic use default id
USE PLL DDR1
USE PLL NORMAL
PLL FREQUENCE = 1104 MHZ
DRAM master priority setting ok.
Auto calculate timing parameter!
para_dram_tpr0 = 0047214f
para_dram_tpr1 = 01c2294b
para_dram_tpr2 = 00061043
tcl = 6,tcwl = 4
DRAM TIMING PARA0 = 0b0e180b
DRAM TIMING PARA1 = 0003040f
DRAM TIMING PARA2 = 0406050a
DRAM TIMING PARA3 = 0000400c
DRAM TIMING PARA4 = 05020405
DRAM TIMING PARA5 = 05050403
DRAM TIMING PARA8 = 90003310
DRAM PHY INTERFACE PARA = 02040102
DRAM VTC is disable
DRAM dynamic DQS/DQ ODT is on
DRAM SIZE AUTO SCAN ENABLE.
NOW,the work mode register value is 004318e5
DRAM DQS gate is open.
DRAM two rank training is on,the value is 93003587
DRAM training error,PGSR0 = 9040005f
DRAM low 8  DQs information,DXnGSR = 023f9e80
DRAM high 8 DQs information,DXnGSR = 023d9e00
DRAM do not have two rank,NOW set one rank
DRAM recovery DQS gate mode 0
DRAM DQS gate is close.
DRAM work mode register value = 004318e4
DRAM SIZE =512 M
set one rank ODTMAP
DRAM simple test OK.
dram size =512
Reg pull reg_val=0x00005150,read=0x00005150

read CCM_AHB1_RST_REG0[0x00004040]

read CCM_AHB1_RST_REG0[0x00004040]

read enable CCM_AHB1_RST_REG0[0x00104040]
read s CCM_AHB1_GATE0_CTRL[0x00104040]
SPI clock source :0x23c34600
spi spic->sclk =0x03404c2e
spic_set_clk:mclk=0x03404c2e
Succeed in reading Boot1 file head.
The size of uboot is 00090000.
Ready to disable icache.
Jump to secend Boot.
[      0.407]

U-Boot 2011.09-rc1-00000-gd7d6afeaa-dirty (Apr 26 2024 - 22:18:20) Allwinner Technology 

[      0.417]version: 1.1.0
[      0.419]uboot commit : d7d6afeaaeaf434a19e1135b67e44255d17b5ce2

[      0.426]pmbus:   normal or secure os
ready
[      0.431]PMU: AXP221
[      0.433]PMU: AXP22x found
bat_vol=0, ratio=100
[      0.438]PMU: dcdc3 1200
[      0.441]PMU: pll1 1008 Mhz,PLL6=600 Mhz
AXI=336 Mhz,AHB=200 Mhz, APB1=100 Mhz 
dcdc1_vol = 3000
dcdc2_vol = 1100
dcdc3_vol = 1200
dcdc4_vol = 0
dcdc5_vol = 1500
aldo2_vol = 2500
aldo3_vol = 3000
dldo2_vol = 3300
find power_sply to end
vbus exist
no battery, limit to dc
fel key new mode
run key detect
fel_key_mode:0
no key input
dram_para_set start
dram_para_set end
[      0.567]DRAM:  512 MiB
relocation Offset is: 1e21f000
save config for small mem_size 
board.c 661
workmode = 0
flash size =16 M
sunxi spinor is initing...
Reg pull reg_val=0x5150,read=0x5150

read CCM_AHB1_RST_REG0[0x4040]

read CCM_AHB1_RST_REG0[0x4040]

read enable CCM_AHB1_RST_REG0[0x104040]
read s CCM_AHB1_GATE0_CTRL[0x104040]
SPI clock source :0x23c34600
spi spic->sclk =0x51be56d
spic_set_clk:mclk=0x51be56d
sunxi spi init OK
spinor id:0x1840ef
spinor size:0x8000
spi_freq = 80000000
[      0.661]sunxi flash init ok
fail to find part named env
Using default environment

In:    serial
Out:   serial
Err:   serial
flash size =16 M
the flash size is 16 MB
--------fastboot partitions--------
mbr not exist
base bootcmd=sunxi_flash nor_read 40008000 0 2900;bootm 400a8000
no misc partition is found
bootcmd set setargs_nor
to be run cmd=sunxi_flash nor_read 40008000 0 2900;bootm 400a8000
sunxi_serial: sn_filename is not exist
serial is: 2867973871c3ffffd28a
check kernel/rootfs on sdcard
[      0.707][mmc]: mmc driver ver 2018-06-25 14:21:00
[      0.712][mmc]: get sdc_phy_wipe fail.
[      0.716][mmc]: get sdc0 sdc_erase fail.
[      0.720][mmc]: get sdc_f_max fail,use default 50000000Hz
[      0.725][mmc]: get sdc_ex_dly_used fail,use default dly
[      0.731][mmc]: SUNXI SD/MMC: 0
[      0.735][mmc]: mmc_config_clock: clk 400000
[      0.743][mmc]: *Try SD card 0*
[      0.746][mmc]: mmc 0 cmd 8 err 100
[      0.750][mmc]: mmc send if cond failed
[      0.754][mmc]: mmc 0 cmd 55 err 100
[      0.758][mmc]: send app cmd failed
[      0.762][mmc]: *Try MMC card 0*
[      0.769][mmc]: mmc 0 cmd 1 err 100
[      0.773][mmc]: mmc send op cond failed
[      0.777][mmc]: Card did not respond to voltage select!
[      0.782][mmc]: ***SD/MMC 0 init error!!!***
[      0.786][mmc]: erase_grp_size:0x0WrBlk * 0x0 = 0x0 Byte
[      0.792][mmc]: secure_feature 0x0
[      0.795][mmc]: secure_removal_type  0x0
card0 init failed
sdcard plugout
WORK_MODE_BOOT
board_status_probe
[      0.805]key trigger
startup status = 0
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
====== pressed count=5, g_power_key=1
POWER LED:ON
lcd_used = 1
lcd_bl_en: name=, port=0, port_num=0, mul_sel=0, pull=0, drv_level=0, data=0, gpio=0
smcl's set manager is NULL
<axp22, dc1sw>
power cause: 0
boot
sunxi_bmp_logo_display
bmp_info.buffer = 5f000000
decode bmp ok
begin to set framebuffer
screen_id =0, screen_width =480, screen_height =640
frame buffer address 5f001000
begin to show layer
bmp display finish
addr = 5f000000 
### main_loop entered: bootdelay=0

[      1.576]Hit any key to stop autoboot:  0 
read nor
[      1.868]sunxi flash nor read[40008000] :offset 0, 10496 sectors OK
## Booting kernel from Legacy Image at 400a8000 ...
   Image Name:   ARM OpenWrt Linux-3.4.39
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3764264 Bytes = 3.6 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
para err in disp_ioctl, cmd = 0xa,screen id = 1
[      1.960][mmc]: MMC Device 2 not found
[      1.964][mmc]:  mmc ????????????????^ not find,so not exit
force sunxi spinor exit
dma 0x5eb99a6c int is not used yet
dma 0x5eb99a6c int is free, you do not need to free it again
dma 0x5eb99a88 int is not used yet
dma 0x5eb99a88 int is free, you do not need to free it again
reload config to 0x43000000
[      1.971]
Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Linux version 3.4.39 (alfchen@alfchen-NUC) (gcc version 6.4.1 (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) ) #1053 SMP PREEMPT Sat Apr 27 03:48:45 UTC 2024
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: sun8i
[    0.000000] Initialized persistent memory from 43080800-430907ff
[    0.000000] cma: CMA: reserved 128 MiB at 58000000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] On node 0 totalpages: 131072
[    0.000000] free_area_init_node: node 0, pgdat c0848d40, node_mem_map c0893000
[    0.000000]   Normal zone: 1152 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 129920 pages, LIFO batch:31
[    0.000000] script_init enter!
[    0.000000] script_init exit!
[    0.000000] PERCPU: Embedded 7 pages/cpu @c0d27000 s6592 r8192 d13888 u32768
[    0.000000] pcpu-alloc: s6592 r8192 d13888 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 129920
[    0.000000] Kernel command line: boot_type=3 disp_para=100 fb_base=0x5f000000 config_size=40960 boot.serialno=2867973871c3ffffd28a boot.hardware=sun8i console=ttyS1,115200 rootfstype=squashfs rw r8
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 512MB = 512MB total
[    0.000000] Memory: 378864k/378864k available, 145424k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xe0800000 - 0xff000000   ( 488 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0701000   (7140 kB)
[    0.000000]       .init : 0xc0701000 - 0xc072d9c0   ( 179 kB)
[    0.000000]       .data : 0xc072e000 - 0xc0849a80   (1135 kB)
[    0.000000]        .bss : 0xc084a900 - 0xc0892c34   ( 289 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:416
[    0.000000] Architected local timer running at 24.00MHz.
[    0.000000] Switching to timer-based delay loop
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] Console: colour dummy device 80x30
[    0.000186] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000)
[    0.000205] pid_max: default: 4096 minimum: 301
[    0.000339] Security Framework initialized
[    0.000418] Mount-cache hash table entries: 512
[    0.001249] CPU: Testing write buffer coherency: ok
[    0.001474] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.001484] [sunxi_smp_prepare_cpus] enter
[    0.001521] Setting up static identity map for 0x405c4798 - 0x405c47f0
[    0.006192] CPU1: Booted secondary processor
[    0.006258] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.010000] CPU2: Booted secondary processor
[    0.010000] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.010334] CPU3: Booted secondary processor
[    0.010334] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.010446] Brought up 4 CPUs
[    0.010446] SMP: Total of 4 processors activated (19200.00 BogoMIPS).
[    0.014716] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.014837] pinctrl core: initialized pinctrl subsystem
[    0.024919] NET: Registered protocol family 16
[    0.025797] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[    0.025797] script_sysfs_init success
[    0.025797] sunxi_dump_init success
[    0.025797] gpiochip_add: registered GPIOs 0 to 383 on device: sunxi-pinctrl
[    0.025797] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver
[    0.025797] gpiochip_add: registered GPIOs 1024 to 1031 on device: axp-pinctrl
[    0.025797] persistent_ram: uncorrectable error in header
[    0.025797] persistent_ram: no valid data in buffer (sig = 0xffffffff)
[    0.034221] console [ram-1] enabled
[    0.034650] [sunxi-module]: [sunxi-module.0] probe success
[    0.034798] script config pll3 to 297 Mhz
[    0.035015] script config pll4 to 300 Mhz
[    0.035152] script config pll6 to 600 Mhz
[    0.035271] script config pll8 to 408 Mhz
[    0.035492] script config pll9 to 480 Mhz
[    0.035610] script config pll10 to 297 Mhz
[    0.035996] sunxi_default_clk_init
[    0.036205] try to set pll6ahb1 to 200000000
[    0.036363] try to set ahb clk source to pll6ahb1
[    0.036478] set ahb clk source to pll6ahb1
[    0.036689] try to set ahb1 to 200000000
[    0.036805] try to set apb1 to 100000000
[    0.070242] bio: create slab <bio-0> at 0
[    0.070590] [ARISC] :sunxi-arisc driver v1.02
[    0.084878] [ARISC] :arisc version: [v0.1.33]
[    0.091590] [ARISC] :sunxi-arisc driver v1.02 startup succeeded
[    0.091810] pwm module init!
[    0.093196] SCSI subsystem initialized
[    0.093196] usbcore: registered new interface driver usbfs
[    0.093196] usbcore: registered new interface driver hub
[    0.093196] usbcore: registered new device driver usb
[    0.093196] twi_chan_cfg()348 - [twi0] has no twi_regulator.
[    0.093196] twi_chan_cfg()348 - [twi1] has no twi_regulator.
[    0.093196] twi_chan_cfg()348 - [twi2] has no twi_regulator.
[    0.093196] Linux video capture interface: v2.00
[    0.093196] [axp22_init_chip] read axp22 ic type=0x6
[    0.100400] current_limit = 1200000
[    0.100598] Advanced Linux Sound Architecture Driver Version 1.0.25.
[    0.101091] cfg80211: Calling CRDA to update world regulatory domain
[    0.102062] Switching to clocksource arch_sys_counter
[    0.102215] FS-Cache: Loaded
[    0.102215] CacheFiles: Loaded
[    0.105960] hci: ERR: get ehci1 abh clk failed.
[    0.106080] hci: ERR: clock_init failed
[    0.106302] hci: ERR: get ohci1 abh clk failed.
[    0.106416] hci: ERR: clock_init failed
[    0.107795] NET: Registered protocol family 2
[    0.108260] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.108882] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.109332] TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
[    0.109712] TCP: Hash tables configured (established 16384 bind 16384)
[    0.109924] TCP: reno registered
[    0.110354] NET: Registered protocol family 1
[    0.111287] [pm]aw_pm_init!
[    0.111409] standby_mode = 1. 
[    0.111523] wakeup src cnt is : 2. 
[    0.111737] [exstandby]leave extended_standby_enable_wakeup_src : event 0x800000
[    0.111854] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_map 0x80
[    0.112065] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_group 0x0
[    0.112277] [exstandby]leave extended_standby_enable_wakeup_src : event 0x800000
[    0.112395] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_map 0x280
[    0.112606] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_group 0x0
[    0.112839] sunxi_reg_init enter
[    0.113435] audit: initializing netlink socket (disabled)
[    0.113584] type=2000 audit(0.100:1): initialized
[    0.114939] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.115111] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.115617] msgmni has been set to 995
[    0.116849] io scheduler noop registered
[    0.117063] io scheduler deadline registered
[    0.117244] io scheduler cfq registered (default)
[    0.117376] [DISP]disp_module_init
[    0.118588] OSAL_Pwm_Config pwm 0, <19531 / 100000> , ret = 0
[    0.119064] ret:0,fb_base:0x5f000000
[    0.119335] [DISP] parser_disp_init_para,line:184:    fetch script data disp_init.screen2_output_type fail
[    0.119564] [DISP] parser_disp_init_para,line:201:    fetch script data disp_init.screen2_output_mode fail
[    0.119885] fb0_format 0
[    0.120116] scaler_mode 0
[    0.120232] fb_width 1e0
[    0.120345] fb_height 280
[    0.120464] [DISP] parser_disp_init_para,line:266:    fetch script data disp_init.fb2_format fail
[    0.120785] [DISP] parser_disp_init_para,line:271:    fetch script data disp_init.fb2_scaler_mode_enable fail
[    0.121107] [DISP] parser_disp_init_para,line:276:    fetch script data disp_init.fb2_width fail
[    0.121428] [DISP] parser_disp_init_para,line:281:    fetch script data disp_init.fb2_height fail
[    0.126905] [fb_map_boot_logo]w=480,h=640,phy_addr=0x5f001000, vir_addr=0xe086b000
[    0.134795] set registered_fb[0] to 480x640
[    0.135027] set registered_fb[1] to 480x640
[    0.135346] set registered_fb[2] to 480x640
[    0.135574] set registered_fb[3] to 480x640
[    0.135898] set registered_fb[4] to 480x640
[    0.136126] set registered_fb[5] to 480x640
[    0.136354] set registered_fb[6] to 480x640
[    0.136671] set registered_fb[7] to 480x640
[    0.137113] [DISP]disp_module_init finish
[    0.137357] sw_uart_get_devinfo()2038 - uart0 has no uart_regulator.
[    0.137573] sw_uart_get_devinfo()2038 - uart1 has no uart_regulator.
[    0.138159] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
[    0.138535] uart1: ttyS1 at MMIO 0x1c28400 (irq = 33) is a SUNXI
[    0.138751] sw_uart_pm()1296 - uart1 clk is already enable
[    0.138873] sw_console_setup()1696 - console setup baud 115200 parity n bits 8, flow n
[    0.234683] console [ttyS1] enabled
[    0.434839] loop: module loaded
[    0.533368] [NAND]panic_buff_handle 0xd8588000 ,0x58588000
[    1.023764] [NAND][NAND]nand init start, nand0_used_flag is 0
[    1.155326] [NAND]nand_cache_level err! 0[NAND]nand_capacity_level err! 0
[    1.163178] regisger ISP =====================
[    1.168232] [NAND]nand driver is disabled 
[    1.172913] no ldo for moto, ignore it
[    1.177270] no ldo moto voltage config, ignore it
[    1.182753] sunxi_vibrator init end
[    1.186802] lradc_fetch_sysconfig_para: used script_get_item  err. 
[    1.194627] sunxi_spi_chan_cfg()1389 - [spi-0] has no spi_regulator.
[    1.202300] spi spi0: master is unqueued, this is deprecated
[    1.209030] NorFlash ID: 0xef4018 - 0xef40
[    1.213717] m25p80 spi0.0: found w25q128, expected at25df641
[    1.220214] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    1.225916] Creating 4 MTD partitions on "(null)":
[    1.231459] 0x000000000000-0x0000000a0000 : "boot"
[    1.237640] 0x0000000a0000-0x0000005a0000 : "kernel"
[    1.244062] 0x0000005a0000-0x000000600000 : "config"
[    1.250354] 0x000000600000-0x000001000000 : "rootfs"
[    1.256701] tun: Universal TUN/TAP device driver, 1.6
[    1.262525] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.269565] RTW: module init start
[    1.273555] RTW: rtl8188fu v5.11.5.4-0-g65b8f0aad.20220413
[    1.279746] RTW: build time: Jan 31 2024 16:06:31
[    1.285229] RTW: rtw_inetaddr_notifier_register
[    1.290434] usbcore: registered new interface driver rtl8188fu
[    1.297106] RTW: module init ret=0
[    1.300994] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.328430] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.337546] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus number 1
[    1.346610] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000
[    1.370025] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00
[    1.376801] ehci_irq: highspeed device connect
[    1.381955] hub 1-0:1.0: USB hub found
[    1.386327] hub 1-0:1.0: 1 port detected
[    1.391112] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.418141] sunxi-ohci sunxi-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    1.426870] sunxi-ohci sunxi-ohci.1: new USB bus registered, assigned bus number 2
[    1.435506] sunxi-ohci sunxi-ohci.1: irq 105, io mem 0xf1c1a400
[    1.504373] hub 2-0:1.0: USB hub found
[    1.508742] hub 2-0:1.0: 1 port detected
[    1.513551] usbcore: registered new interface driver cdc_acm
[    1.519939] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.529079] usbcore: registered new interface driver cdc_wdm
[    1.535569] Initializing USB Mass Storage driver...
[    1.541184] usbcore: registered new interface driver usb-storage
[    1.548047] USB Mass Storage support registered.
[    1.553322] usbcore: registered new interface driver ums-sddr09
[    1.560133] usbcore: registered new interface driver ums-sddr55
[    1.566900] usbcore: registered new interface driver usbserial
[    1.573585] usbserial: USB Serial Driver core
[    1.578561] usbcore: registered new interface driver option
[    1.584894] USB Serial support registered for GSM modem (1-port)
[    1.710039] usb 1-1: new high-speed USB device number 2 using sunxi-ehci
[    1.861461] RTW: 
[    1.861464] usb_endpoint_descriptor(0):
[    1.868055] RTW: bLength=7
[    1.871177] RTW: bDescriptorType=5
[    1.875149] RTW: bEndpointAddress=81
[    1.879217] RTW: wMaxPacketSize=512
[    1.883203] RTW: bInterval=0
[    1.886599] RTW: RT_usb_endpoint_is_bulk_in = 1
[    1.891738] RTW: 
[    1.891741] usb_endpoint_descriptor(1):
[    1.898326] RTW: bLength=7
[    1.901533] RTW: bDescriptorType=5
[    1.905408] RTW: bEndpointAddress=2
[    1.909379] RTW: wMaxPacketSize=512
[    1.913456] RTW: bInterval=0
[    1.916753] RTW: RT_usb_endpoint_is_bulk_out = 2
[    1.921989] RTW: 
[    1.921992] usb_endpoint_descriptor(2):
[    1.928673] RTW: bLength=7
[    1.931786] RTW: bDescriptorType=5
[    1.935661] RTW: bEndpointAddress=3
[    1.939727] RTW: wMaxPacketSize=512
[    1.943709] RTW: bInterval=0
[    1.947005] RTW: RT_usb_endpoint_is_bulk_out = 3
[    1.952336] RTW: nr_endpoint=3, in_num=1, out_num=2
[    1.952341] 
[    1.959601] RTW: USB_SPEED_HIGH
[    1.963197] RTW: CHIP TYPE: RTL8188FU
[    1.967721] RTW: Chip Version Info: CHIP_8188F_S2_1T1R_RomVer(0)
[    1.974514] RTW: _ConfigChipOutEP_8188F OutEpQueueSel(0x05), OutEpNumber(2)
[    1.982711] RTW: EEPROM type is E-FUSE
[    1.987334] RTW: Boot from EFUSE, Autoload OK !
[    1.992964] RTW: hal_EfuseSwitchToBank: Efuse switch bank to 0
[    2.124710] RTW: hal_ReadEFuse_WiFi: data end at address=0x6e
[    2.131491] RTW: HW EFUSE
[    2.134720] RTW: 0x000: 29 81 00 FC  0B 00 00 00  00 0C 04 4C  10 07 00 00  
[    2.144638] RTW: 0x010: 2B 2A 2A 2A  29 2E 2D 2D  2D 2D 2D 22  FF FF FF FF  
[    2.154658] RTW: 0x020: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.164570] RTW: 0x030: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.174477] RTW: 0x040: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.184398] RTW: 0x050: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.194320] RTW: 0x060: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.204231] RTW: 0x070: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.214141] RTW: 0x080: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.224053] RTW: 0x090: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.234058] RTW: 0x0A0: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.243970] RTW: 0x0B0: FF FF FF FF  FF FF FF FF  23 18 24 00  00 00 00 FF  
[    2.253894] RTW: 0x0C0: FF 02 00 10  00 FF 00 FF  00 00 FF FF  FF FF FF FF  
[    2.263804] RTW: 0x0D0: DA 0B 79 F1  47 66 40 C8  FE 0F 97 AC  8E 09 03 52  
[    2.273706] RTW: 0x0E0: 65 61 6C 74  65 6B 09 03  38 30 32 2E  31 31 6E 00  
[    2.283619] RTW: 0x0F0: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.293537] RTW: 0x100: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.303453] RTW: 0x110: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.313467] RTW: 0x120: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.323391] RTW: 0x130: C1 B6 FF FF  FF FF FF FF  FF FF 00 11  FF FF FF FF  
[    2.333309] RTW: 0x140: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.343229] RTW: 0x150: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.353149] RTW: 0x160: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.363064] RTW: 0x170: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.372980] RTW: 0x180: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.382894] RTW: 0x190: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.392912] RTW: 0x1A0: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.402818] RTW: 0x1B0: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.412724] RTW: 0x1C0: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.422642] RTW: 0x1D0: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.432560] RTW: 0x1E0: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.442471] RTW: 0x1F0: FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF  
[    2.452384] RTW: EEPROM VID = 0x bda
[    2.456451] RTW: EEPROM PID = 0xf179
[    2.460537] RTW: hal_com_config_channel_plan chplan:0x23
[    2.466633] RTW: Hal_EfuseParsePowerSavingMode_8188F...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(1)
[    2.478330] RTW: ### PS params=>  power_mgnt(2),usbss_enable(0) ###
[    2.487708] RTW: kfree Pwr Trim flag:1
[    2.492079] RTW: bb_gain:0
[    2.498835] RTW: rtl8188f_FirmwareDownload fw: FW_NIC, size: 20832
[    2.505817] RTW: rtl8188f_FirmwareDownload: fw_ver=f fw_subver=0001 sig=0x88f1, Month=05, Date=06, Hour=09, Minute=34
[    2.517805] RTW: rtl8188f_FirmwareDownload(): Shift for fw header!
[    2.524876] RTW: rtl8188f_FirmwareDownload by IO write!
[    2.562463] RTW: polling_fwdl_chksum: Checksum report OK! (1, 0ms), REG_MCUFWDL:0x00050105
[    2.573332] RTW: _8051Reset8188: Finish
[    2.586836] RTW: _FWFreeToGo: Polling FW ready OK! (73, 10ms), REG_MCUFWDL:0x000501c6
[    2.595738] RTW: rtl8188f_FirmwareDownload: DLFW OK !
[    2.601555] RTW: rtl8188f_FirmwareDownload success. write_fw:1, 80ms
[    2.608834] RTW:  <=== rtl8188f_FirmwareDownload()
[    2.616214] RTW: CardDisableRTL8188FU
[    2.624961] RTW: hal_read_mac_hidden_rpt OK! (1, 10ms), fwdl:1, id:0x19
[    2.632515] RTW: InitAdapterVariablesByPROM_8188FU(): REPLACEMENT = 0
[    2.639768] RTW: rtw_hal_read_chip_info in 650 ms
[    2.645244] RTW: init_channel_set((null)) ChannelPlan ID:0x23, ch num:14
[    2.652832] RTW: [RF_PATH] ver_id.RF_TYPE:RF_1T1R
[    2.658253] RTW: [RF_PATH] HALSPEC's rf_reg_trx_path_bmp:0x11, rf_reg_path_avail_num:1, max_tx_cnt:1
[    2.668504] RTW: [RF_PATH] PG's trx_path_bmp:0x00, max_tx_cnt:0
[    2.675283] RTW: [RF_PATH] Registry's trx_path_bmp:0x00, tx_path_lmt:0, rx_path_lmt:0
[    2.684183] RTW: [RF_PATH] HALDATA's trx_path_bmp:0x11, max_tx_cnt:1
[    2.691348] RTW: [RF_PATH] HALDATA's rf_type:RF_1T1R, NumTotalRFPath:1
[    2.698793] RTW: rtw_hal_rfpath_init trx_path_bmp:0x11(RF_1T1R), NumTotalRFPath:1, max_tx_cnt:1
[    2.708562] RTW: [TRX_Nss] HALSPEC - tx_nss:1, rx_nss:1
[    2.714569] RTW: [TRX_Nss] Registry - tx_nss:0, rx_nss:0
[    2.720576] RTW: [TRX_Nss] HALDATA - tx_nss:1, rx_nss:1
[    2.726571] RTW: rtw_hal_trxnss_init tx_nss:1, rx_nss:1
[    2.732617] RTW: init_mlme_default_rate_set: support CCK
[    2.738712] RTW: init_mlme_default_rate_set: support OFDM
[    2.745319] RTW: NR_RECVBUFF: 8, recvbuf_nr: 8
[    2.750483] RTW: MAX_RECVBUF_SZ: 32768
[    2.754752] RTW: NR_PREALLOC_RECV_SKB: 8
[    2.759476] RTW: rtw_alloc_macid((null)) if1, mac_addr:ff:ff:ff:ff:ff:ff macid:1
[    2.767923] RTW: rtw_init_pwrctrl_priv: IPS_mode=1, LPS_mode=2, LPS_level=0
[    2.776010] RTW: IQK FW offload:disable
[    2.780399] RTW: Init_ODM_ComInfo_8188f(): Fv=0 Cv=12
[    2.786152] RTW: rtw_regsty_chk_target_tx_power_valid return _FALSE for band:0, path:0, rs:0, t:-1
[    2.796394] RTW: phy_ConfigBBWithPgParaFile(): No File PHY_REG_PG.txt, Load from HWImg Array!
[    2.806106] RTW: default power by rate loaded
[    2.811114] RTW: pwrctrlpriv.bSupportRemoteWakeup~~~~~~
[    2.817112] RTW: pwrctrlpriv.bSupportRemoteWakeup~~~[1]~~~
[    2.823320] RTW: rtw_macaddr_cfg mac addr:c8:fe:0f:97:ac:8e
[    2.829703] RTW: bDriverStopped:True, bSurpriseRemoved:False, bup:0, hw_init_completed:0
[    2.838821] RTW: rtw_cfg80211_init_wiphy_band:rf_type=0
[    2.844846] RTW: [HT] HAL Support STBC = 0x01
[    2.849785] RTW: rtw_wiphy_alloc(phy0)
[    2.854200] RTW: rtw_wdev_alloc(padapter=e0999000)
[    2.859624] RTW: rtw_wiphy_register(phy0)
[    2.864552] RTW: rtw_ndev_init(wlan0) if1 mac_addr=c8:fe:0f:97:ac:8e
[    2.872322] RTW: rtw_ndev_notifier_call(wlan0) state:16
[    2.878858] RTW: rtw_ndev_notifier_call(wlan0) state:5
[    2.885579] file system registered
[    2.890609] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    2.898441] android_usb gadget: Number of LUNs=1
[    2.903688]  lun0: LUN: removable file: (no medium)
[    2.909603] android_usb gadget: android_usb ready
[    2.915168] sunxikbd_init failed. 
[    2.919447] sunxi-rtc sunxi-rtc: rtc core: registered sunxi-rtc as rtc0
[    2.927057] i2c /dev entries driver
[    3.091176] i2c driver added
[    3.094567] sunxi cedar version 0.1 
[    3.098778] [cedar]: install start!!!
[    3.103100] [cedar]: install end!!!
[    3.107106] sunxi_pwr_key_fetch_sysconfig_para script_parser_fetch "pwr_ctrl" pwr_ctrl_used = -679256216
[    3.117844] =========script_get_err============
[    3.126356] axp22_dcdc3: Failed to create debugfs directory
[    3.135092] sdhci: Secure Digital Host Controller Interface driver
[    3.142121] sdhci: Copyright(c) Pierre Ossman
[    3.147036] [mmc]: SD/MMC/SDIO Host Controller Driver(v1.126 2018-10-15 14:05) Compiled in Jan 31 2024 at 16:06:26
[    3.158708] is sdio=0
[    3.161321] [mmc]: get mmc0's sdc_power is null!
[    3.166609] force 2 used=0
[    3.169695] is sdio=1
[    3.172300] force 2 sdio=1
[    3.175384] [mmc]: get mmc2's 2xmode ok, val = 0
[    3.180670] [mmc]: get mmc2's ddrmode ok, val = 0
[    3.185975] [mmc]: MMC host used card: 0x5, boot card: 0x0, io_card 4
[    3.194184] [mmc]: sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    3.207142] [mmc]: sdc2 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[    3.219770] no led1_active_low, sunxi_leds_fetch_sysconfig_para failed!
[    3.227282] =========script_get_err============
[    3.232400] [led]:sunxi_led_init begin!
[    3.236809] =====led_sysconfig_para=====.
[    3.241351] led1 gpio number is 362
[    3.245300] led1_trigger gpio number is default-on
[    3.251020] Registered led device: led1
[    3.255981] usbcore: registered new interface driver usbhid
[    3.262263] usbhid: USB HID core driver
[    3.266678] zram: num_devices not specified. Using default: 1
[    3.273142] zram: Creating 1 devices ...
[    3.278174] Linux telephony interface: v1.00
[    3.283802] usbcore: registered new interface driver snd-usb-audio
[    3.291826] [ audio ] err:try to get audio_pa_en failed !
[    3.297899] request gpio failed!
[    3.301592] plugio = 357, enio = 356
[    3.305805] audio_run_thread
[    3.305965] [ audio ] err:try to get audio_linein_detect failed!
[    3.305973] [ audio ] err:try to get usb_detect failed!
[    3.305979] [ audio ] err:try to get mic_array_led_ctrl failed!
[    3.307913] codec_set_bias_level,line:2240, SND_SOC_BIAS_STANDBY
[    3.335289] audio plug io value = 1, oldvalue = -1, audio en expectval=1, val=1
[    3.345276] asoc: codec-aif1 <-> sunxi-codec mapping ok
[    3.351392] asoc: codec-aif2 <-> sunxi-codec-aif2-dai mapping ok
[    3.358379] asoc: codec-aif3 <-> sunxi-codec-aif2-dai mapping ok
[    3.368622] u32 classifier
[    3.371730]     Actions configured
[    3.375663] Netfilter messages via NETLINK v0.30.
[    3.380986] nf_conntrack version 0.5.0 (7967 buckets, 31868 max)
[    3.388040] ctnetlink v0.93: registering with nfnetlink.
[    3.394065] IPVS: Registered protocols ()
[    3.398641] IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
[    3.407059] IPVS: Creating netns size=840 id=0
[    3.412120] IPVS: ipvs loaded.
[    3.415806] IPv4 over IPv4 tunneling driver
[    3.420903] gre: GRE over IPv4 demultiplexor driver
[    3.426402] ip_gre: GRE over IPv4 tunneling driver
[    3.432236] ip_tables: (C) 2000-2006 Netfilter Core Team
[    3.438350] TCP: cubic registered
[    3.442202] Initializing XFRM netlink socket
[    3.447038] NET: Registered protocol family 17
[    3.452075] NET: Registered protocol family 15
[    3.457646] ThumbEE CPU extension supported.
[    3.462491] Registering SWP/SWPB emulation handler
[    3.468278] [LCD]lcd_module_init
[    3.472034] ====== lcd_init
[    3.475610] =========== default LCD_open_flow 0
[    3.480920] [LCD]lcd_module_init finish
[    3.481332] disp_lcd_set_bright d7a8b3c0 50
[    3.481339] OSAL_Pwm_Config -678302720 19922 0
[    3.481350] OSAL_Pwm_Config pwm 0, <19922 / 100000> , ret = 0
[    3.481355] disp_lcd_set_bright d7a8b3c0 50
[    3.481360] OSAL_Pwm_Config -678302720 19922 0
[    3.481367] OSAL_Pwm_Config pwm 0, <19922 / 100000> , ret = 0
[    3.481388] disp_lcd_set_bright d7a8b3c0 50
[    3.481394] OSAL_Pwm_Config -678302720 19922 0
[    3.481400] OSAL_Pwm_Config pwm 0, <19922 / 100000> , ret = 0
[    3.534999] sunxi-rtc sunxi-rtc: setting system clock to 1970-01-01 00:00:07 UTC (7)
[    3.543711] ths_fetch_sysconfig_para: type err  device_used = 1. 
[    3.551019] sunxi_cpu_budget_vftable_init: support only one vf_table
[    3.558499] CPU Budget:Register notifier
[    3.563023] CPU Budget:register Success
[    3.567377] sunxi-budget-cooling sunxi-budget-cooling: Cooling device registered: thermal-budget-0
[    3.579805] ALSA device list:
[    3.583207]   #0: sndcodec
[    3.589375] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    3.597654] Freeing init memory: 176K
[    3.935543] init: Console is alive
[    3.939704] init: - preinit -
[    4.030053] ====codec_init_events===
[    4.130053] WRN:L2917(drivers/usb/sunxi_usb/udc/sunxi_udc.c):pdev is null
[    4.238434] gpio_keys_polled_init start
[    4.409627] block: (block info) there is no /dev/by-name/UDISK
formating /dev/by-name/UDISK to vfat
mkfs.vfat: can't open '/dev/by-name/UDISK': No such file or directory
[    4.448600] mount_root: mounting /dev/root
[    4.454168] mount_root: loading kmods from internal overlay
[    4.560888] block: attempting to load /etc/config/fstab
[    4.591399] block: extroot: not configured
[    4.655863] procd: - early -
[    4.777438] procd: - ubus -
[    4.781265] procd (1): /proc/96/oom_adj is deprecated, please use /proc/96/oom_score_adj instead.
[    4.886869] procd: - init -
Please press Enter to activate this console.
[    4.970417] android_usb: already disabled
[    5.285043] udevd[138]: starting version 3.2
[    5.286110] adb_open
[    5.286128] adb_bind_config
[    5.286159] ep_matches, wrn: endpoint already claimed, ep(0xc082d3a4, 0xd7aca980, ep1in-bulk)
[    5.428770] udevd[138]: specified group 'tty' unknown
[    5.435089] udevd[138]: specified group 'dialout' unknown
[    5.441850] udevd[138]: specified group 'kmem' unknown
[    5.448191] udevd[138]: specified group 'input' unknown
[    5.454674] udevd[138]: specified group 'video' unknown
[    5.461518] udevd[138]: specified group 'lp' unknown
[    5.467718] udevd[138]: specified group 'disk' unknown
[    5.473937] udevd[138]: specified group 'cdrom' unknown
[    5.480355] udevd[138]: specified group 'tape' unknown
[    5.496830] udevd[209]: starting eudev-3.2
[    5.521532] vmalloc: allocation failure: 0 bytes
[    5.527034] kmodloader: page allocation failure: order:0, mode:0xd0
[    5.539547] Mali<2>: Inserting Mali v900 device driver. 
[    5.546042] Mali<2>: Compiled: Jan 31 2024, time: 16:04:59.
[    5.552677] Mali<2>: Driver revision: r8p1-00rel0-e008d1c2d
[    5.559385] Mali<2>: mali_module_init() registering device
[    5.565959] Mali: ERR: /home/alfchen/ProjectData/miyoo_allwinner/a33_tina3.5.1/lichee/linux-3.4/modules/gpu/mali-utgard/kernel_mode/driver/src/devicedrv/mali/linux/mali_platform.c
[    5.584266]            aw_init() 672
[    5.584275]            Failed to get regulator!
[    5.593858] 
[    5.595724] Mali: Set gpu frequency to 384 MHz
[    5.601876] Mali: Mali GPU initialization finished.
[    5.607672] Mali<2>: mali_module_init() registering driver
[    5.614547] Mali<2>: mali_probe(): Called for platform device mali-utgard
[    5.625464] Mali<2>: Mali SWAP: Swap out threshold vaule is 60M
[    5.632704] Mali<2>: Mali memory settings (shared: 0x1F228000)
[    5.639591] Mali<2>: Using device defined frame buffer settings (0x00384000@0x58200000)
[    5.649707] Mali<2>: Memory Validator installed for Mali physical address base=0x58200000, size=0x00384000
[    5.661102] Mali<2>: Mali PM domain: Creating Mali PM domain (mask=0x00001000)
[    5.669741] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP0
[    5.676590] Mali<2>: Mali PP: Base address of PP core: 0x1c48000
[    5.684013] Mali<2>: Found Mali GPU Mali-400 MP r1p1
[    5.706663] Mali<2>: Mali L2 cache: Created Mali_L2:  64K, 4-way, 64byte cache line,  64bit external bus
[    5.718486] Mali<2>: Mali MMU: Creating Mali MMU: Mali_GP_MMU
[    5.726641] Mali<2>: mali_mmu_probe_irq_acknowledge: intstat 0x3
[    5.730024] Mali<2>: Probe: Page fault detect: PASSED
[    5.730024] Mali<2>: Probe: Bus read error detect: PASSED
[    5.746501] Mali<2>: Mali GP: Creating Mali GP core: Mali_GP
[    5.754087] Mali<2>: Mali MMU: Creating Mali MMU: Mali_PP0_MMU
[    5.761260] Mali<2>: mali_mmu_probe_irq_acknowledge: intstat 0x3
[    5.768338] Mali<2>: Probe: Page fault detect: PASSED
[    5.770025] Mali<2>: Probe: Bus read error detect: PASSED
[    5.780828] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP0
[    5.787739] Mali<2>: Mali PP: Base address of PP core: 0x1c48000
[    5.795179] Mali<2>: Mali MMU: Creating Mali MMU: Mali_PP1_MMU
[    5.802432] Mali<2>: mali_mmu_probe_irq_acknowledge: intstat 0x3
[    5.809450] Mali<2>: Probe: Page fault detect: PASSED
[    5.810027] Mali<2>: Probe: Bus read error detect: PASSED
[    5.822144] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP1
[    5.829107] Mali<2>: Mali PP: Base address of PP core: 0x1c4a000
[    5.836641] Mali<2>: 2+0 PP cores initialized
[    5.842142] Mali<2>: Mali GPU Timer: 500
[    5.846997] Mali<2>: Mali GPU Utilization: Utilization handler installed 
[    5.856258] Mali<2>: 
[    5.858816] android_usb gadget: high-speed config #1: android
[    5.866115] mali_probe(): Successfully initialized driver for platform device mali-utgard
[    5.875825] Mali: Mali device driver loaded
[    5.885523] xt_time: kernel timezone is -0000
[    7.385029] jffs2: notice: (511) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    8.924506] set AIF1_CLK 
[    8.927936] codec_set_bias_level,line:2235, SND_SOC_BIAS_PREPARE
[    8.934862] late_enable_dac,line:482
[    8.943948] late_enable_dac,line:482
[    8.948149] post:open:ac_speaker_event,line:610
[    8.956436] codec_set_bias_level,line:2231, SND_SOC_BIAS_ON
[    9.112430] codec_set_bias_level,line:2235, SND_SOC_BIAS_PREPARE
[    9.119321] pre:close:ac_speaker_event,line:631
[    9.124762] codec_set_bias_level,line:2240, SND_SOC_BIAS_STANDBY
[    9.220122] audio plug io value = 1, oldvalue = 1, audio en expectval=1, val=0
[    9.284783] bsp_disp_lcd_set_bright 0 50
[    9.289312] disp_lcd_set_bright d7a8b3c0 50
[    9.294253] OSAL_Pwm_Config -678302720 19922 0
[    9.299485] OSAL_Pwm_Config pwm 0, <19922 / 100000> , ret = 0
[    9.712448] RTW: rtw_ndev_notifier_call(wlan0) state:13
[    9.718686] RTW: _netdev_open(wlan0) , bup=0
[    9.727537] RTW:  power-on :REG_SYS_CLKR 0x09=0xfc. REG_CR 0x100=0x3f.
[    9.735184] RTW:  MAC has already power on.
[    9.741496] RTW: rtl8188f_FirmwareDownload fw: FW_NIC, size: 20832
[    9.748734] RTW: rtl8188f_FirmwareDownload: fw_ver=f fw_subver=0001 sig=0x88f1, Month=05, Date=06, Hour=09, Minute=34
[    9.760993] RTW: rtl8188f_FirmwareDownload(): Shift for fw header!
[    9.768084] RTW: rtl8188f_FirmwareDownload by IO write!
[    9.810363] RTW: polling_fwdl_chksum: Checksum report OK! (1, 0ms), REG_MCUFWDL:0x00050105
[    9.821872] RTW: _8051Reset8188: Finish
[    9.835360] RTW: _FWFreeToGo: Polling FW ready OK! (71, 10ms), REG_MCUFWDL:0x000501c6
[    9.844413] RTW: rtl8188f_FirmwareDownload: DLFW OK !
[    9.850407] RTW: rtl8188f_FirmwareDownload success. write_fw:1, 90ms
[    9.857869] RTW:  <=== rtl8188f_FirmwareDownload()
[    9.863676] RTW: fw download ok!
[    9.884876] RTW: PHY_MACConfig8188F OK!
[    9.937478] RTW: PHY_BBConfig8188F OK!
[    9.985578] set AIF1_CLK 
[    9.989111] codec_set_bias_level,line:2235, SND_SOC_BIAS_PREPARE
[    9.996089] late_enable_dac,line:482
[   10.005496] late_enable_dac,line:482
[   10.009655] post:open:ac_speaker_event,line:610
[   10.018158] codec_set_bias_level,line:2231, SND_SOC_BIAS_ON
[   10.200736] RTW: PHY_RFConfig8188F OK!
[   10.212738] RTW: usb_AggSettingRxUpdate: RX Aggregation USB mode, size=20KB, timeout=1024us
[   10.234229] RTW: txpath=0x1, rxpath=0x1
[   10.238790] RTW: txpath_1ss:0x1, num:1
[   10.335225] RTW: rtl8188fu_hal_init in 610ms
[   10.340295] RTW: rtw_hal_set_macaddr_port wlan0- hw port(0) mac_addr =c8:fe:0f:97:ac:8e
[   10.350724] RTW: [HW_VAR_ENABLE_RX_BAR] 0x6A2=0x500
[   10.366010] RTW: rtw_hal_set_macaddr_port wlan0- hw port(0) mac_addr =c8:fe:0f:97:ac:8e
[   10.376611] RTW: #### hw_var_set_opmode() -4562 hw_port(0) mode = 2 ####
[   10.385232] RTW: rtw_rf_get_kfree_tx_gain_offset path:0, ch:6, bb_gain_sel:0, kfree_offset:0
[   10.395970] RTW: kfree gain_offset 0x55:0x82060 RTW:  after :0x2060
[   10.405571] RTW: MAC Address = c8:fe:0f:97:ac:8e
[   10.410940] RTW: rtw_start_drv_threads(wlan0) enter
[   10.416681] RTW: rtw_start_drv_threads(wlan0) start RTW_CMD_THREAD
[   10.424201] RTW: -871x_drv - drv_open, bup=1
[   10.429415] RTW: cfg80211_rtw_set_power_mgmt(wlan0) enabled:1, timeout:-1
[   10.437499] RTW: rtw_ndev_notifier_call(wlan0) state:1
[   12.045132] bsp_disp_lcd_set_bright 0 50
[   12.049693] disp_lcd_set_bright d7a8b3c0 50
[   12.055766] OSAL_Pwm_Config -678302720 19922 0
[   12.061209] OSAL_Pwm_Config pwm 0, <19922 / 100000> , ret = 0
[   12.440382] RTW: ==>rtw_ps_processor .fw_state(8)
[   12.445931] RTW: ==>ips_enter cnts:1
[   12.450131] RTW: nolinked power save enter
[   12.454854] RTW: ===> rtw_ips_pwr_down...................
[   12.461282] RTW: ====> rtw_ips_dev_unload...
[   12.469522] RTW: usb_read_port_cancel
[   12.473985] RTW: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[   12.484725] RTW: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[   12.495471] RTW: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[   12.506235] RTW: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[   12.516980] RTW: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[   12.527733] RTW: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[   12.538352] RTW: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[   12.549263] RTW: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[   12.559991] RTW: usb_write_port_cancel
[   12.564511] RTW: ==> rtl8188fu_hal_deinit
[   12.569852] RTW: CardDisableRTL8188FU
[   12.602243] RTW: <=== rtw_ips_pwr_down..................... in 150ms```

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment