/1TB-file.txt
Last active Feb 16, 2017
| smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-62-generic] (local build) | |
| Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org | |
| === START OF INFORMATION SECTION === | |
| Model Family: Western Digital Caviar Green | |
| Device Model: WDC WD10EADS-11M2B2 | |
| Serial Number: WD-WCAV59534464 | |
| LU WWN Device Id: 5 0014ee 25985d7d9 | |
| Firmware Version: 80.00A80 | |
| User Capacity: 1.000.204.886.016 bytes [1,00 TB] | |
| Sector Sizes: 512 bytes logical, 4096 bytes physical | |
| Device is: In smartctl database [for details use: -P show] | |
| ATA Version is: ATA8-ACS (minor revision not indicated) | |
| SATA Version is: SATA 2.6, 3.0 Gb/s | |
| Local Time is: Thu Feb 16 08:32:53 2017 CET | |
| SMART support is: Available - device has SMART capability. | |
| SMART support is: Enabled | |
| === START OF READ SMART DATA SECTION === | |
| SMART overall-health self-assessment test result: PASSED | |
| General SMART Values: | |
| Offline data collection status: (0x82) Offline data collection activity | |
| was completed without error. | |
| Auto Offline Data Collection: Enabled. | |
| Self-test execution status: ( 0) The previous self-test routine completed | |
| without error or no self-test has ever | |
| been run. | |
| Total time to complete Offline | |
| data collection: (20100) seconds. | |
| Offline data collection | |
| capabilities: (0x7b) SMART execute Offline immediate. | |
| Auto Offline data collection on/off support. | |
| Suspend Offline collection upon new | |
| command. | |
| Offline surface scan supported. | |
| Self-test supported. | |
| Conveyance Self-test supported. | |
| Selective Self-test supported. | |
| SMART capabilities: (0x0003) Saves SMART data before entering | |
| power-saving mode. | |
| Supports SMART auto save timer. | |
| Error logging capability: (0x01) Error logging supported. | |
| General Purpose Logging supported. | |
| Short self-test routine | |
| recommended polling time: ( 2) minutes. | |
| Extended self-test routine | |
| recommended polling time: ( 231) minutes. | |
| Conveyance self-test routine | |
| recommended polling time: ( 5) minutes. | |
| SCT capabilities: (0x3031) SCT Status supported. | |
| SCT Feature Control supported. | |
| SCT Data Table supported. | |
| SMART Attributes Data Structure revision number: 16 | |
| Vendor Specific SMART Attributes with Thresholds: | |
| ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE | |
| 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 | |
| 3 Spin_Up_Time 0x0027 131 123 021 Pre-fail Always - 6441 | |
| 4 Start_Stop_Count 0x0032 070 070 000 Old_age Always - 30141 | |
| 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 | |
| 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 | |
| 9 Power_On_Hours 0x0032 053 053 000 Old_age Always - 34711 | |
| 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 | |
| 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 | |
| 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 396 | |
| 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 71 | |
| 193 Load_Cycle_Count 0x0032 061 061 000 Old_age Always - 419702 | |
| 194 Temperature_Celsius 0x0022 117 087 000 Old_age Always - 30 | |
| 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 | |
| 197 Current_Pending_Sector 0x0032 196 196 000 Old_age Always - 783 | |
| 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 44 | |
| 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 | |
| 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 48 | |
| SMART Error Log Version: 1 | |
| No Errors Logged | |
| SMART Self-test log structure revision number 1 | |
| Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error | |
| # 1 Short offline Completed: read failure 60% 34711 1328 | |
| SMART Selective self-test log data structure revision number 1 | |
| SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS | |
| 1 0 0 Not_testing | |
| 2 0 0 Not_testing | |
| 3 0 0 Not_testing | |
| 4 0 0 Not_testing | |
| 5 0 0 Not_testing | |
| Selective self-test flags (0x0): | |
| After scanning selected spans, do NOT read-scan remainder of disk. | |
| If Selective self-test is pending on power-up, resume after 0 minute delay. | |
| smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-62-generic] (local build) | |
| Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org | |
| === START OF INFORMATION SECTION === | |
| Model Family: Seagate Desktop HDD.15 | |
| Device Model: ST4000DM000-1F2168 | |
| Serial Number: Z3018WRR | |
| LU WWN Device Id: 5 000c50 065b223b1 | |
| Firmware Version: CC52 | |
| User Capacity: 4.000.787.030.016 bytes [4,00 TB] | |
| Sector Sizes: 512 bytes logical, 4096 bytes physical | |
| Rotation Rate: 5900 rpm | |
| Form Factor: 3.5 inches | |
| Device is: In smartctl database [for details use: -P show] | |
| ATA Version is: ATA8-ACS T13/1699-D revision 4 | |
| SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) | |
| Local Time is: Thu Feb 16 08:18:18 2017 CET | |
| SMART support is: Available - device has SMART capability. | |
| SMART support is: Enabled | |
| === START OF READ SMART DATA SECTION === | |
| SMART overall-health self-assessment test result: PASSED | |
| General SMART Values: | |
| Offline data collection status: (0x00) Offline data collection activity | |
| was never started. | |
| Auto Offline Data Collection: Disabled. | |
| Self-test execution status: ( 0) The previous self-test routine completed | |
| without error or no self-test has ever | |
| been run. | |
| Total time to complete Offline | |
| data collection: ( 592) seconds. | |
| Offline data collection | |
| capabilities: (0x73) SMART execute Offline immediate. | |
| Auto Offline data collection on/off support. | |
| Suspend Offline collection upon new | |
| command. | |
| No Offline surface scan supported. | |
| Self-test supported. | |
| Conveyance Self-test supported. | |
| Selective Self-test supported. | |
| SMART capabilities: (0x0003) Saves SMART data before entering | |
| power-saving mode. | |
| Supports SMART auto save timer. | |
| Error logging capability: (0x01) Error logging supported. | |
| General Purpose Logging supported. | |
| Short self-test routine | |
| recommended polling time: ( 1) minutes. | |
| Extended self-test routine | |
| recommended polling time: ( 520) minutes. | |
| Conveyance self-test routine | |
| recommended polling time: ( 2) minutes. | |
| SCT capabilities: (0x1085) SCT Status supported. | |
| SMART Attributes Data Structure revision number: 10 | |
| Vendor Specific SMART Attributes with Thresholds: | |
| ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE | |
| 1 Raw_Read_Error_Rate 0x000f 119 099 006 Pre-fail Always - 229949488 | |
| 3 Spin_Up_Time 0x0003 092 091 000 Pre-fail Always - 0 | |
| 4 Start_Stop_Count 0x0032 088 088 020 Old_age Always - 12590 | |
| 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 | |
| 7 Seek_Error_Rate 0x000f 074 060 030 Pre-fail Always - 4320600056 | |
| 9 Power_On_Hours 0x0032 085 085 000 Old_age Always - 13693 | |
| 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 | |
| 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 226 | |
| 183 Runtime_Bad_Block 0x0032 099 099 000 Old_age Always - 1 | |
| 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 | |
| 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 | |
| 188 Command_Timeout 0x0032 100 096 000 Old_age Always - 333 333 373 | |
| 189 High_Fly_Writes 0x003a 096 096 000 Old_age Always - 4 | |
| 190 Airflow_Temperature_Cel 0x0022 067 046 045 Old_age Always - 33 (Min/Max 21/33) | |
| 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 | |
| 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 47 | |
| 193 Load_Cycle_Count 0x0032 090 090 000 Old_age Always - 21807 | |
| 194 Temperature_Celsius 0x0022 033 054 000 Old_age Always - 33 (0 14 0 0 0) | |
| 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 | |
| 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 | |
| 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 | |
| 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 2572h+35m+01.741s | |
| 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 6946901707 | |
| 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 4104443642 | |
| SMART Error Log Version: 1 | |
| No Errors Logged | |
| SMART Self-test log structure revision number 1 | |
| Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error | |
| # 1 Short offline Completed without error 00% 13692 - | |
| SMART Selective self-test log data structure revision number 1 | |
| SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS | |
| 1 0 0 Not_testing | |
| 2 0 0 Not_testing | |
| 3 0 0 Not_testing | |
| 4 0 0 Not_testing | |
| 5 0 0 Not_testing | |
| Selective self-test flags (0x0): | |
| After scanning selected spans, do NOT read-scan remainder of disk. | |
| If Selective self-test is pending on power-up, resume after 0 minute delay. | |
| [99296.489446] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command | |
| [99301.705303] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command | |
| [99301.909276] usb 2-2: device not accepting address 69, error -62 | |
| [99307.113488] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command | |
| [99312.329488] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command | |
| [99312.533509] usb 2-2: device not accepting address 70, error -62 | |
| [99317.737370] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command | |
| [99322.953588] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command | |
| [99323.157365] usb 2-2: device not accepting address 71, error -62 | |
| [99323.157387] xhci_hcd 0000:00:14.0: Cannot set link state. | |
| [99323.157407] usb usb2-port2: cannot disable (err = -32) | |
| [99327.145373] usb usb2-port2: Cannot enable. Maybe the USB cable is bad? | |
| [99327.145406] xhci_hcd 0000:00:14.0: Cannot set link state. | |
| [99327.145430] usb usb2-port2: cannot disable (err = -32) | |
| [99327.145494] usb usb2-port2: unable to enumerate USB device | |
| [99327.145512] xhci_hcd 0000:00:14.0: Cannot set link state. | |
| [99327.145533] usb usb2-port2: cannot disable (err = -32) | |
| [99370.169748] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command | |
| [99375.385460] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command | |
| [99375.589655] usb 2-2: device not accepting address 73, error -62 | |
| [99377.144283] usb 2-2: new SuperSpeed USB device number 74 using xhci_hcd | |
| [99377.170562] usb 2-2: device descriptor read/8, error -71 | |
| [99377.273468] usb 2-2: new SuperSpeed USB device number 74 using xhci_hcd | |
| [99382.289497] usb 2-2: device descriptor read/8, error -110 | |
| [99382.393467] xhci_hcd 0000:00:14.0: Cannot set link state. | |
| [99382.393506] usb usb2-port2: cannot disable (err = -32) | |
| [99382.561606] usb 2-2: new SuperSpeed USB device number 75 using xhci_hcd | |
| [99382.578310] usb 2-2: New USB device found, idVendor=067b, idProduct=2773 | |
| [99382.578323] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 | |
| [99382.578331] usb 2-2: Product: ATAPI-6 Bridge Controller | |
| [99382.578338] usb 2-2: Manufacturer: Prolific Technology Inc. | |
| [99382.578344] usb 2-2: SerialNumber: 0123456789000000005 | |
| [99382.579435] usb 2-2: Set SEL for device-initiated U1 failed. | |
| [99382.579492] usb 2-2: Set SEL for device-initiated U2 failed. | |
| [99382.579739] usb-storage 2-2:1.0: USB Mass Storage device detected | |
| [99382.580784] scsi host20: usb-storage 2-2:1.0 | |
| [99383.578326] scsi 20:0:0:0: Direct-Access ST4000DM 000-1F2168 CC52 PQ: 0 ANSI: 0 | |
| [99383.579588] sd 20:0:0:0: Attached scsi generic sg1 type 0 | |
| [99383.579819] sd 20:0:0:0: [sdb] Very big device. Trying to use READ CAPACITY(16). | |
| [99383.580099] sd 20:0:0:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB) | |
| [99383.580329] sd 20:0:0:0: [sdb] Write Protect is off | |
| [99383.580339] sd 20:0:0:0: [sdb] Mode Sense: 03 00 00 00 | |
| [99383.580562] sd 20:0:0:0: [sdb] No Caching mode page found | |
| [99383.580571] sd 20:0:0:0: [sdb] Assuming drive cache: write through | |
| [99383.584537] sd 20:0:0:0: [sdb] Very big device. Trying to use READ CAPACITY(16). | |
| [99383.644792] sdb: sdb1 sdb2 sdb3 | |
| [99383.646370] sd 20:0:0:0: [sdb] Very big device. Trying to use READ CAPACITY(16). | |
| [99383.647145] sd 20:0:0:0: [sdb] Attached SCSI disk | |
| [99384.343739] EXT4-fs (sdb3): mounted filesystem with ordered data mode. Opts: (null) | |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment