/gist:2340773
Created Apr 9, 2012
| sudo smartctl --all /dev/sda | |
| smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.0.0-17-generic] (local build) | |
| Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net | |
| === START OF INFORMATION SECTION === | |
| Model Family: Seagate Momentus 7200.4 | |
| Device Model: ST9500420AS | |
| Serial Number: 5VJCM2D9 | |
| LU WWN Device Id: 5 000c50 03900031e | |
| Firmware Version: 0003LVM1 | |
| User Capacity: 500,107,862,016 bytes [500 GB] | |
| Sector Size: 512 bytes logical/physical | |
| Device is: In smartctl database [for details use: -P show] | |
| ATA Version is: 8 | |
| ATA Standard is: ATA-8-ACS revision 4 | |
| Local Time is: Sun Apr 8 08:46:28 2012 COT | |
| SMART support is: Available - device has SMART capability. | |
| SMART support is: Enabled | |
| === START OF READ SMART DATA SECTION === | |
| SMART overall-health self-assessment test result: FAILED! | |
| Drive failure expected in less than 24 hours. SAVE ALL DATA. | |
| See vendor-specific Attribute list for failed Attributes. | |
| General SMART Values: | |
| Offline data collection status: (0x00) Offline data collection activity | |
| was never started. | |
| Auto Offline Data Collection: Disabled. | |
| Self-test execution status: ( 0) The previous self-test routine completed | |
| without error or no self-test has ever | |
| been run. | |
| Total time to complete Offline | |
| data collection: ( 0) seconds. | |
| Offline data collection | |
| capabilities: (0x73) SMART execute Offline immediate. | |
| Auto Offline data collection on/off support. | |
| Suspend Offline collection upon new | |
| command. | |
| No Offline surface scan supported. | |
| Self-test supported. | |
| Conveyance Self-test supported. | |
| Selective Self-test supported. | |
| SMART capabilities: (0x0003) Saves SMART data before entering | |
| power-saving mode. | |
| Supports SMART auto save timer. | |
| Error logging capability: (0x01) Error logging supported. | |
| General Purpose Logging supported. | |
| Short self-test routine | |
| recommended polling time: ( 1) minutes. | |
| Extended self-test routine | |
| recommended polling time: ( 109) minutes. | |
| Conveyance self-test routine | |
| recommended polling time: ( 2) minutes. | |
| SCT capabilities: (0x103b) SCT Status supported. | |
| SCT Error Recovery Control supported. | |
| SCT Feature Control supported. | |
| SCT Data Table supported. | |
| SMART Attributes Data Structure revision number: 10 | |
| Vendor Specific SMART Attributes with Thresholds: | |
| ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE | |
| 1 Raw_Read_Error_Rate 0x000f 090 086 034 Pre-fail Always - 65517349 | |
| 3 Spin_Up_Time 0x0003 100 098 000 Pre-fail Always - 0 | |
| 4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1311 | |
| 5 Reallocated_Sector_Ct 0x0033 030 030 036 Pre-fail Always FAILING_NOW 1444 | |
| 7 Seek_Error_Rate 0x000f 063 059 030 Pre-fail Always - 98826442143 | |
| 9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 18549963753688 | |
| 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 | |
| 12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1126 | |
| 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 | |
| 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 1554 | |
| 188 Command_Timeout 0x0032 100 095 000 Old_age Always - 103081181222 | |
| 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 | |
| 190 Airflow_Temperature_Cel 0x0022 076 041 045 Old_age Always In_the_past 24 (0 37 24 13) | |
| 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 160 | |
| 192 Power-Off_Retract_Count 0x0032 067 067 000 Old_age Always - 66362 | |
| 193 Load_Cycle_Count 0x0032 062 062 000 Old_age Always - 77421 | |
| 194 Temperature_Celsius 0x0022 024 059 000 Old_age Always - 24 (0 2 0 0) | |
| 195 Hardware_ECC_Recovered 0x001a 048 046 000 Old_age Always - 65517349 | |
| 196 Reallocated_Event_Count 0x000f 099 099 030 Pre-fail Always - 1638 (26250, 0) | |
| 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 2 | |
| 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 2 | |
| 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 | |
| 254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0 | |
| SMART Error Log Version: 1 | |
| ATA Error Count: 1208 (device log contains only the most recent five errors) | |
| CR = Command Register [HEX] | |
| FR = Features Register [HEX] | |
| SC = Sector Count Register [HEX] | |
| SN = Sector Number Register [HEX] | |
| CL = Cylinder Low Register [HEX] | |
| CH = Cylinder High Register [HEX] | |
| DH = Device/Head Register [HEX] | |
| DC = Device Command Register [HEX] | |
| ER = Error register [HEX] | |
| ST = Status register [HEX] | |
| Powered_Up_Time is measured from power on, and printed as | |
| DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, | |
| SS=sec, and sss=millisec. It "wraps" after 49.710 days. | |
| Error 1208 occurred at disk power-on lifetime: 2263 hours (94 days + 7 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| 60 00 e8 ff ff ff 4f 00 00:33:42.015 READ FPDMA QUEUED | |
| 60 00 10 b0 b3 de 48 00 00:33:41.793 READ FPDMA QUEUED | |
| 60 00 08 a0 b3 de 48 00 00:33:41.496 READ FPDMA QUEUED | |
| 60 00 08 ff ff ff 4f 00 00:33:41.379 READ FPDMA QUEUED | |
| 60 00 08 ff ff ff 4f 00 00:33:41.378 READ FPDMA QUEUED | |
| Error 1207 occurred at disk power-on lifetime: 2262 hours (94 days + 6 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 40 51 00 2b ae 1a 0a Error: UNC at LBA = 0x0a1aae2b = 169520683 | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| 60 00 00 08 ae 1a 4a 00 00:01:17.343 READ FPDMA QUEUED | |
| 60 00 00 08 af 1a 4a 00 00:01:17.341 READ FPDMA QUEUED | |
| 27 00 00 00 00 00 e0 00 00:01:17.341 READ NATIVE MAX ADDRESS EXT | |
| ec 00 00 00 00 00 a0 00 00:01:17.332 IDENTIFY DEVICE | |
| ef 03 45 00 00 00 a0 00 00:01:17.332 SET FEATURES [Set transfer mode] | |
| Error 1206 occurred at disk power-on lifetime: 2262 hours (94 days + 6 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 40 51 00 2b ae 1a 0a Error: UNC at LBA = 0x0a1aae2b = 169520683 | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| 60 00 00 08 af 1a 4a 00 00:01:15.016 READ FPDMA QUEUED | |
| 60 00 00 08 ae 1a 4a 00 00:01:14.191 READ FPDMA QUEUED | |
| 60 00 c0 48 ad 1a 4a 00 00:01:14.188 READ FPDMA QUEUED | |
| 60 00 38 08 ad 1a 4a 00 00:01:14.188 READ FPDMA QUEUED | |
| 60 00 00 08 ac 1a 4a 00 00:01:14.179 READ FPDMA QUEUED | |
| Error 1205 occurred at disk power-on lifetime: 2262 hours (94 days + 6 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 40 51 00 ff ff ff 0f Error: WP at LBA = 0x0fffffff = 268435455 | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| 61 00 50 ff ff ff 4f 00 00:02:19.059 WRITE FPDMA QUEUED | |
| 60 00 20 ff ff ff 4f 00 00:02:19.059 READ FPDMA QUEUED | |
| 60 00 18 ff ff ff 4f 00 00:02:19.057 READ FPDMA QUEUED | |
| ea 00 00 00 00 00 a0 00 00:02:19.029 FLUSH CACHE EXT | |
| 60 00 20 ff ff ff 4f 00 00:02:18.994 READ FPDMA QUEUED | |
| Error 1204 occurred at disk power-on lifetime: 2258 hours (94 days + 2 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| 60 00 00 ff ff ff 4f 00 00:06:25.726 READ FPDMA QUEUED | |
| 27 00 00 00 00 00 e0 00 00:06:25.725 READ NATIVE MAX ADDRESS EXT | |
| ec 00 00 00 00 00 a0 00 00:06:25.716 IDENTIFY DEVICE | |
| ef 03 45 00 00 00 a0 00 00:06:25.716 SET FEATURES [Set transfer mode] | |
| 27 00 00 00 00 00 e0 00 00:06:25.715 READ NATIVE MAX ADDRESS EXT | |
| SMART Self-test log structure revision number 1 | |
| Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error | |
| # 1 Short offline Completed: unknown failure 90% 2263 0 | |
| # 2 Extended offline Completed: unknown failure 90% 2263 0 | |
| # 3 Extended offline Completed: unknown failure 90% 2263 0 | |
| SMART Selective self-test log data structure revision number 1 | |
| SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS | |
| 1 0 0 Not_testing | |
| 2 0 0 Not_testing | |
| 3 0 0 Not_testing | |
| 4 0 0 Not_testing | |
| 5 0 0 Not_testing | |
| Selective self-test flags (0x0): | |
| After scanning selected spans, do NOT read-scan remainder of disk. | |
| If Selective self-test is pending on power-up, resume after 0 minute delay. | |
| LilArooni ~: |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment