Last active
October 15, 2020 01:01
-
-
Save bakueikozo/b4111af2668124feb4df142bb01a7124 to your computer and use it in GitHub Desktop.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
[0]HELLO! BOOT0 is starting! | |
[2]boot0 commit : e9d7c88390ded1551ff4a4bcfef31cbc9cf717cb | |
[27]key press : s | |
7 | |
U-Boot 2014.07 (Jul 21 2020 - 03:52:33) Allwinner Technology | |
uboot commit : 8 | |
i2c_init: by cpux | |
err: gpio count < =0 ,gpio_count is: -1 | |
[I2C-ERROR]:sunxi_i2c_init() 427 error:fail to set the i2c gpio | |
[1.162]pmbus: ready | |
axp: get node[/soc/pmu0] error | |
axp_probe error | |
[1.168]PMU: cpux 408 Mhz,AXI=408 Mhz | |
PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz | |
key value = 4294967295, fel_key = [256,426] | |
DRAM: 64 MiB | |
[1.181]fdt addr: 0x82ae7c20 | |
[1.184]gd->fdt_size: 0xc120 | |
Relocation Offset is: 03541000 | |
axp: get node[/soc/pmu0] error | |
int sunxi_dma_init--- | |
irq enable | |
[1.260]display init start | |
drv_disp_init | |
init_clocks: finish init_clocks. | |
irq_of_parse_and_map irq 1 fail for be | |
pwm_request 628 | |
pwm_request: reg = 0x1c21000. pwm = 0. | |
request pwm success, pwm = 0. | |
pll_freq=297000000HZ, lcd_dclk_freq=10000000HZ, clk_div=29 | |
******************************* | |
*** | |
*** LCD Panel Parameter Check | |
*** | |
*** by guozhenjie | |
*** | |
******************************** | |
*** | |
*** Interface: | |
*** lcd_if: 1 | |
*** lcd_hv_if: 0 | |
*** lcd_cpu_if: 7 | |
*** Lcd Frm to RGB565 | |
*** | |
*** Timing: | |
*** lcd_x: 240 | |
*** lcd_y: 240 | |
*** lcd_ht: 495 | |
*** lcd_hbp: 11 | |
*** lcd_vt: 270 | |
*** lcd_vbp: 5 | |
*** lcd_hspw: 10 | |
*** lcd_vspw: 4 | |
*** lcd_frame_frq: 74Hz | |
*** | |
*** WRN03: Recommend "lcd_dclk_frq = 8" | |
*** | |
*** LCD Panel Parameter Check End | |
******************************* | |
pwm_config 551 | |
sunxi_pwm_config 190 | |
panel driver ST7789VW_240x240 register | |
disp0 device type(1) enable | |
pll_freq=297000000HZ, lcd_dclk_freq=10000000HZ, clk_div=29 | |
unable to get ldo_count from [regulator0] | |
unable to find regulator vcc-lcd from [pmu1_regu] or [pmu2_regu] | |
enable power vcc-lcd, ret=-1 | |
[1.401]display init end | |
[1.403]flash init start | |
workmode = 0,storage type = 0 | |
[1.408]NAND: NAND_UbootInit | |
[1.410]NAND_UbootInit start | |
[1.413]NB1: enter NAND_LogicInit | |
[1.416]SpiNandHwInit: Start Nand Hardware initializing Jul 21 2020 03:53:21..... | |
[1.423]uboot: nand version: 3 6020 20200228 1256 | |
int sunxi_dma_init--- | |
irq enable | |
_change_spic_clk: 0x01c05024=0x1009 | |
_change_spic_clk_v1: mclk=0xc8 | |
_change_spic_clk: 0x01c05024=0x1004 | |
_change_spic_clk_v1: mclk=0xc8 | |
_change_spic_clk: 0x01c05024=0x1001 | |
_change_spic_clk_v1: mclk=0xc8 | |
_get_spic_clk_v1: sclk0=0x32 | |
[1.507]not burn nand partition table! | |
[2.017]NB1: nftl num: 1 | |
[2.019]init nftl: 0 | |
pwm_enable 568 | |
sunxi_pwm_enable 289 | |
sunxi_pwm_pin_set_state 129 | |
[2.924]NB1: NAND_LogicInit ok, result = 0x0 | |
[2.928]NAND_UbootInit end: 0x0 | |
[2.931]sunxi flash init ok | |
used mbr [0], count = 8 | |
[2.939]flash init end | |
[2.941]try to burn key | |
logo addr = 0x83f80000 | |
can't get bootlogo partition | |
do not find fastboot status flag | |
--------fastboot partitions-------- | |
-total partitions:8- | |
-name- -start- -size- | |
boot-resource: 400000 100000 | |
env : 500000 40000 | |
boot : 540000 600000 | |
rootfs : b40000 3200000 | |
rootfs_data : 3d40000 1900000 | |
misc : 5640000 40000 | |
private : 5680000 40000 | |
UDISK : 56c0000 0 | |
----------------------------------- | |
[3.064]base bootcmd=run setargs_nand boot_normal | |
[3.068]bootcmd set setargs_nand | |
[3.071]key -1 | |
[3.072]cant find rcvy value | |
[3.075]cant find fstbt value | |
[3.077]misc partition found | |
[3.080]to be run cmd=run setargs_nand boot_normal | |
disable nand error: FDT_ERR_BADPATH | |
disable nand error: FDT_ERR_BADPATH | |
[3.100](weak)update dtb dram start | |
## error: update_fdt_dram_para : FDT_ERR_NOTFOUND | |
PowerBus = 0( 2:vBus 3:acBus other: not exist) | |
no battery exist | |
sunxi_bmp_logo_display | |
reading bootlogo.bmp | |
38454 bytes read in 13 ms (2.8 MiB/s) | |
[3.135]bmp file buffer: 0x80000000, bmp_info.buffer: 82010000 | |
screen_id =0, screen_width =240, screen_height =240 | |
[3.146]inter uboot shell | |
Hit any key to stop autoboot: 0 | |
sunxi#ssssssssssssssssssssssssssssssssssssssssssssss |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment