trendmicro-virusbuster

BootROM - 1.73

Booting from MMC
BootROM: RSA Public key verification PASSED
BootROM: CSK block signature verification PASSED
BootROM: Boot header signature verification PASSED
BootROM: Flash ID verification PASSED
BootROM: Box ID verification PASSED
BootROM: JTAG is enabled
BootROM: Image checksum verification PASSED
BootROM: Boot image signature verification PASSED
aaaaaaaaaaaaaaaaaaaagd->baudrate=115200
whoAmI()=0

 __   __                      _ _
|  \/  | __ _ _ ____   _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| |  | | (_| | |   \ V /  __/ | |
|_|  |_|\__,_|_|    \_/ \___|_|_|
         _   _     ____              _
        | | | |   | __ )  ___   ___ | |_
        | | | |___|  _ \ / _ \ / _ \| __|
        | |_| |___| |_) | (_) | (_) | |_
         \___/    |____/ \___/ \___/ \__|
 ** LOADER **


U-Boot 2013.01 (Jun 22 2017 - 03:36:44) Marvell version: 2015_T1.0p16

Board: A38x-Customer-Board-0
SoC:   MV88F6820 Rev A0
       running 2 CPUs
CPU:   ARM Cortex A9 MPCore (Rev 1) LE
       CPU 0
       CPU    @ 1332 [MHz]
       L2     @ 666 [MHz]
       TClock @ 200 [MHz]
       DDR3    @ 666 [MHz]
       DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM:  512 MiB
NAND:  mvNfcInit() failed.
0 MiB
MMC:   mv_sdh: 0

Map:   Code:                    0x1feec000:0x1ffa18a8
       BSS:                     0x1ffefc38
       Stack:                   0x1f96bf20
       Heap:                    0x1f96c000:0x1feec000
       U-Boot Environment:      0x00300000:0x00380000 (MMC)

Board configuration detected:
Net:
|  port  | Interface | PHY address  |
|--------|-----------|--------------|
| egiga1 |   SGMII   |     0x00     |
, egiga1
uart_2_command 3
b4 mv_serial_init_2
b4 mv_serial_init_2
b4 mv_serial_init_2
b4 mv_serial_init_2
mv_serial_init_2
mv_serial_init_2
mv_serial_init_2
mv_serial_init_2
mv_serial_init_2
mv_serial_init_2
xfax03x03x0x0x0xfb
xfax03x03x0x0x0xfb
length = 18
tmp=fa
cmd[0]=0xfa
tmp=03
cmd[1]=0x3
tmp=03
cmd[2]=0x3
tmp=0
cmd[3]=0x0
tmp=0
cmd[4]=0x0
tmp=0
cmd[5]=0x0
tmp=fb
cmd[6]=0xfb
uart_2_command 2
xfax03x02x07x07x00xfb
xfax03x02x07x07x00xfb
length = 21
tmp=fa
cmd[0]=0xfa
tmp=03
cmd[1]=0x3
tmp=02
cmd[2]=0x2
tmp=07
cmd[3]=0x7
tmp=07
cmd[4]=0x7
tmp=00
cmd[5]=0x0
tmp=fb
cmd[6]=0xfb
reset button detect
button env=released
High
addrDtb = 2048
szImageSizeValue = 30ad
zImageDtbSizeInHex=3113

SECURE = 00000001
Value(s) obtained from eFuse "SECURE" [0X0F9180]:
00000001
tmp   = 00000001
value = 00000001
mmc - MMC sub system

Usage:
mmc mmc read addr blk# cnt
mmc erase blk# cnt
mmc rescan
mmc dev [dev] [part] - show or set current mmc device [partition]
mmc list - lists available devicesmmc setdsr - set DSR register value


MMC read: dev # 0, block # 2048, count 12563 ... 12563 blocks read: OK
zImageSize=30ad

start to do sha1 0x2000000
D6 50 A6 0F FC CF 09 2A 23 46 CA C4 B4 FD C8 D7 B9 09 A0 43
9b 9d 99 db e8 16 ba de 46 73 fe a9 59 ee b8 8c
55 db 31 c5 2d b9 89 00 0d 7a 6e 4a 9d c0 ef a5
ef 24 9e df 80 20 f5 29 42 20 c0 4c a2 e2 bc 32
a7 b3 1c 4d a8 00 d6 6f 0b 67 08 7b 4e a1 4f dc
5c 24 c1 1d ec 7f 58 1b 08 51 e8 63 cc e5 17 2c
96 85 85 c9 e1 23 0c 52 89 f0 d8 2b a3 f9 5f 2b
ae 07 fc f8 c2 48 9a ca 32 2b 4a f4 5d f8 ea ee
6a fa 22 5f 7f 1d ab 52 f4 90 05 71 ad 73 71 af
e9 ac 72 93 71 b6 28 84 ff ea d8 06 1b f3 ae 5a
dd e3 23 53 85 16 71 4b a8 d9 a3 29 75 f3 2f c9
35 a9 b2 7c e9 d9 fc 39 ac c5 e7 93 4a 58 fc d8
6e ed 40 5d ea e7 e8 c5 5e 97 46 2d 86 9c 38 9d
8d fe de 36 a4 d9 90 a2 a8 d5 d9 3b a1 14 0f 2a
42 2e bb 9f bf c2 64 21 0e 4b ea 37 da 83 96 ec
d4 6e 4c 42 0e ec 44 53 63 21 0b 7a a2 44 f7 36
7b 8a f9 ab 96 43 e7 fa d9 70 e2 14 ed f2 ff b3 rsa.len=256

  . OK

## Flattened Device Tree blob at 02000000
   Booting using the fdt blob at 0x02000000
   Loading Device Tree to 00ff9000, end 00fffdff ... OK

   Skipping Device Tree update ('fdt_skip_update' = yes)

Limit DDR size at 3GB due to power of 2 requirement of Address decoding

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 3.10.70 (root@steven-Song-OptiPlex-9020) (gcc version 4.6.4 (Marve
ll GCC release 20160226-c4af733b 64K MAXPAGESIZE ALIGN) ) #1 SMP Tue Aug 23 16:2
8:32 CST 2016
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Marvell Armada 380/381/382/383/384/385/388 (Device Tree), model: Marvel
l Armada 385 Development Board
Memory policy: ECC disabled, Data cache writealloc
PERCPU: Embedded 7 pages/cpu @c140a000 s7168 r8192 d13312 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
Kernel command line: console=ttyS0,115200
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512MB = 512MB total
Memory: 506408k/506408k available, 17880k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xe0800000 - 0xfff00000   ( 503 MB)
    lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc08dc000   (9040 kB)
      .init : 0xc08dc000 - 0xc0c33c00   (3423 kB)
      .data : 0xc0c34000 - 0xc0c8bbe0   ( 351 kB)
       .bss : 0xc0c8bbe0 - 0xc0cec240   ( 386 kB)
Hierarchical RCU implementation.
        RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
NR_IRQS:16 nr_irqs:16 16

  LSP version: linux-3.10.70-2015_T1.1p7

sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B
Console: colour dummy device 80x30
Calibrating delay loop... 2655.84 BogoMIPS (lpj=13279232)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0xc06cbd60 - 0xc06cbdb8
mvebu-pmsu: Initializing Power Management Service Unit
Initializing CPU Reset module
CPU1: Booted secondary processor
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
Brought up 2 CPUs
SMP: Total of 2 processors activated (5311.69 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
xor: measuring software checksum speed
   arm4regs  :  2361.600 MB/sec
   8regs     :  1594.800 MB/sec
   32regs    :  1360.000 MB/sec
xor: using function: arm4regs (2361.600 MB/sec)
pinctrl core: initialized pinctrl subsystem
regulator-dummy: no parameters
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
irq: Cannot allocate irq_descs @ IRQ194, assuming pre-allocated
irq: Cannot allocate irq_descs @ IRQ226, assuming pre-allocated
bio: create slab <bio-0> at 0
raid6: int32x1    169 MB/s
raid6: int32x2    245 MB/s
raid6: int32x4    312 MB/s
raid6: int32x8    316 MB/s
raid6: using algorithm int32x8 (316 MB/s)
raid6: using intx1 recovery algorithm
mvebu-pcie pcie-controller.3: PCIe0.0: link down
mvebu-pcie pcie-controller.3: PCIe1.0: link down
mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io  0x1000-0xfffff]
pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
pci_bus 0000:00: root bus resource [bus 00-ff]
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
PCI: bus1: Fast back to back transfers enabled
PCI: bus2: Fast back to back transfers enabled
pci 0000:00:01.0: PCI bridge to [bus 01]
pci 0000:00:02.0: PCI bridge to [bus 02]
PCI: enabling device 0000:00:01.0 (0140 -> 0143)
PCI: enabling device 0000:00:02.0 (0140 -> 0143)
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@l
inux.it>
PTP clock support registered
Advanced Linux Sound Architecture Driver Initialized.
Switching to clocksource armada_370_xp_clocksource
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
audit: initializing netlink socket (disabled)
type=2000 audit(1.110:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.30 [Flags: R/O].
jffs2: version 2.2. (NAND) ﾂｩ 2001-2006 Red Hat, Inc.
bio: create slab <bio-1> at 1
Btrfs loaded
msgmni has been set to 989
async_tx: api initialized (async)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
mv_xor f1060800.xor: Marvell shared XOR driver
mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq )
mv_xor f1060800.xor: freeing 1 in use descriptors!
mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( intr crc32c )
mv_xor f1060900.xor: Marvell shared XOR driver
mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq )
mv_xor f1060900.xor: freeing 1 in use descriptors!
mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( intr crc32c )
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A
console [ttyS0] enabled
f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 45) is a 16550A
TM button driver installed
loop: module loaded
ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform
mode
ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
scsi0 : ahci_mv_platform
scsi1 : ahci_mv_platform
ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58
ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58
m25p80 spi0.0: found mr25h256, expected w25q32
m25p80 spi0.0: mr25h256 (32 Kbytes)
SoC: model = 0x6820, revision = 0x4
mvPncVirtBase = 0xe0c00000, pncTcamSize = 1024
  o 3 Giga ports supported
  o SKB recycle supported for SWF (Disabled)
  o NETA acceleration mode 4
  o BM supported for CPU: 4 BM pools
  o PnC supported (Enabled)
  o RX Queue support: 8 Queues * 256 Descriptors
  o TX Queue support: 8 Queues * 532 Descriptors
  o GSO supported
  o GRO supported
  o Receive checksum offload supported
  o Transmit checksum offload supported
  o Driver ERROR statistics enabled
  o Driver INFO statistics enabled
  o Driver DEBUG statistics enabled

port #1: is_sgmii=1, is_rgmii=0, phy_addr=0
  o Loading network interface(s) for port #1: cpu_mask=0x3, tx_csum_limit=2048

  o Port 1 is connected to Linux netdevice
    o eth0, ifindex = 2, GbE port = 1
        giga p=1: mtu=1500, mac=54:2a:a2:c6:24:95 (hw config)

libphy: orion_mdio_bus: probed
mdio_bus f1072004.mdio-mi: cannot get PHY at address 1
e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
e1000: Copyright (c) 1999-2006 Intel Corporation.
e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-orion: EHCI orion driver
orion-ehci f1058000.usb: EHCI Host Controller
orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
orion-ehci f1058000.usb: irq 50, io mem 0xf1058000
orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
xhci-hcd f10f0000.usb3: xHCI Host Controller
xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
xhci-hcd f10f0000.usb3: xHCI Host Controller
xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
xhci-hcd f10f8000.usb3: xHCI Host Controller
xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
xhci-hcd f10f8000.usb3: xHCI Host Controller
xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0
i2c /dev entries driver
armada_thermal f10e4078.thermal: Overheat threshold between 92..107
orion_wdt: Initial timeout 171 sec
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
ata2: SATA link down (SStatus 0 SControl 300)
ata1: SATA link down (SStatus 0 SControl 300)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
cpuidle: using governor ladder
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: no vqmmc regulator found
mmc0: no vmmc regulator found
mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA
sdhci-pltfm: SDHCI platform and OF driver helper
armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels s
upported 2
armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: int_coales
cing(1)
armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources threshold 0x2, threshold_
time 0xfffff
mvCesaInit: channels=2, session=640, queue=256
armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) m
ode
cesadev_init(c08f97e8)
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Loading Marvell spi device
cs42l51-codec 0-004a: failed to read I2C
Netfilter messages via NETLINK v0.30.
nfnl_acct: registering with nfnetlink.
nf_conntrack version 0.5.0 (7912 buckets, 31648 max)
xt_time: kernel timezone is -0000
ipip: IPv4 over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP: cubic registered
NET: Registered protocol family 10
mip6: Mobile IPv6
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
Bridge firewalling registered
mmc0: BKOPS_EN bit is not set
8021q: 802.1Q VLAN Support v1.8
mmc0: new high speed MMC card at address 0001
VFP support v0.3: mmcblk0: mmc0:0001 H4G2a 3.64 GiB
mmcblk0boot0: mmc0:0001 H4G2a partition 1 4.00 MiB
mmcblk0boot1: mmc0:0001 H4G2a partition 2 4.00 MiB
mmcblk0rpmb: mmc0:0001 H4G2a partition 3 4.00 MiB
 mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8
 mmcblk0boot1: unknown partition table
 mmcblk0boot0: unknown partition table
implementor 41 architecture 3 part 30 variant 9 rev 4
regulator-dummy: disabling
mvebu-rtc f10a3800.rtc: setting system clock to 2106-02-07 06:28:15 UTC (4294967
295)
ALSA device list:
  No soundcards found.
Freeing unused kernel memory: 3420K (c08dc000 - c0c33000)
Diamond : initramfs start
Diamond : Mounting procfs...
Diamond : Mounting sysfs...
---------------------------------------------------------
---------------------------------------------------------
Linux (none) 3.10.70 #1 SMP Tue Aug 23 16:28:32 CST 2016 armv7l GNU/Linux
---------------------------------------------------------
---------------------------------------------------------
environment (524288 bytes)
Read 0x80000 bytes at 0x300000 on /dev/mmcblk0boot0
Diamond : devicetree_addr=800
Diamond : MOUNT_SYSTEM=/dev/mmcblk0p4
Diamond : Mounting /dev/mmcblk0p4...
EXT4-fs (mmcblk0p4): recovery complete
EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
shaFileSize = 24166400
ae b0 22 7b e5 ce 01 ba c4 e1 6e 6a a1 98 cd f9
cc 50 02 3d f6 9f d7 8a 45 98 cb bc 4b 64 12 af
00 a4 ca 6f 53 bf 0e aa a9 da 50 2a a9 8d 3f 40
df 95 39 d3 0d 98 a9 bb e1 c8 74 b4 93 08 fd 3f
73 f8 34 b9 49 53 6a 55 93 6e 42 9f 74 0c 52 77
72 b7 d5 eb cb cc 34 44 72 63 95 3a ae 79 3c 6e
10 74 f8 86 c9 60 84 e9 ff 77 c3 66 1a 02 39 b9
d5 50 42 75 be 19 55 9e a0 7d f1 8e ff 32 42 fe
d3 3f 6e 05 a3 cb 61 d7 6f 39 96 d1 0f 72 ff 1e
ee f2 b5 0a 61 39 bb d5 f1 43 fb 97 49 d6 f0 65
13 f2 ed 5c 51 68 67 e1 1c 7e fc 8b 3c a2 6c 53
ed 27 a1 e7 08 37 c7 e2 84 44 7c 26 1d dc 00 68
6d 6a 3d 96 75 d9 15 e4 53 e0 76 82 6d 46 ef 81
59 fa d8 6b 46 dc 37 92 24 a8 f6 af 20 c5 6a dd
db 26 32 59 03 b9 fa 12 66 6a 7e 63 c8 84 a5 1a
f3 ef 88 61 49 8d 21 8e d8 b3 2a 1a 32 f9 90 38
  . Verifying the RSA/SHA-1 signature
start to do sha1
C8 61 87 4B 6B AA 5E 57 31 79 41 49 7F 6A 41 A4 FD F2 09 E3
rsa.len=256

  . OK

Diamond : Verify Squashfs:0
Diamond : Check and create dev/ttyS0 and dev/tts/0
rootfs on / type rootfs (rw)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
/dev/mmcblk0p4 on /mnt/system type ext4 (rw,relatime,data=ordered)
/dev/loop0 on /mnt/rootfs type squashfs (ro,relatime)
tmpfs on /mnt/rootfs/dev type tmpfs (rw,relatime,size=2048k)
Diamond : /sbin/init found on /mnt/rootfs, switching rootfs ...
environment (524288 bytes)
Read 0x80000 bytes at 0x300000 on /dev/mmcblk0boot0
mknod: /dev/tm_button: File exists
Diamond : Mounting /dev/mmcblk0p7...
EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: (null)
Diamond : Mount /dev/mmcblk0p7 as /secure OK
Diamond : UserMode
Diamond : Checking Opt file system integrity...
Diamond : Diamond : FSCKCODE=1
Diamond : Mounting /dev/mmcblk0p8...
EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: (null)
Diamond : Mount /dev/mmcblk0p8 as /opt OK
Diamond : run TmResetButtond
Starting logging: OK
Starting watchdog...
Initializing random number generator... read-only file system detected...done
Starting network...
pool #1: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added
eth0: started
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Detect DHCP mode...
Starting runspec...
copying table from file '/tmp/incrond_coredump_rule'
device eth0 entered promiscuous mode
Started runspec...