Xavier 5.0.2 Uart Log - Failed to Flash

gistfile1.txt

[0012.873] I> MB1 (prd-version: 2.3.0.0-t194-41334769-0a17edc1)
[0012.879] I> Boot-mode: Platform RCM
[0012.882] I> Platform: Silicon
[0012.885] I> Chip revision : A02P
[0012.888] I> Bootrom patch version : 15 (correctly patched)
[0012.893] I> ATE fuse revision : 0x200
[0012.897] I> Ram repair fuse : 0x0
[0012.900] I> Ram Code : 0x2
[0012.902] I> rst_source: 0x0, rst_level: 0x0
[0012.908] I> USB configuration success
[0014.972] I> mb2 image downloaded
[0014.997] I> Recovery boot mode 0
[0015.002] I> UPHY full init done
[0015.009] I> MB1 done

[0015.014] I> Welcome to MB2(TBoot-BPMP) Applet (version: default.t194-mobile-27d8d121)
[0015.021] I> DMA Heap @ [0x40020000 - 0x40065800]
[0015.026] I> Default Heap @ [0xd486400 - 0xd48a400]
[0015.031] W> Profiler not initialized
[0015.099] I> sdmmc DDR50 mode
[0015.103] E> SPI_FLASH: Invalid value device id: 7.
[0015.108] I> QSPI Flash is not present.
[0015.114] E> CLK_RST: instance 6 not found in module 44.
[0015.119] E> MPhy CAR configuration failed error = 1747992077
[0015.124] E> UFS initialization failed
[0015.128] I> UFS is not present
[0015.134] I> Found 17 partitions in SDMMC_BOOT (instance 3)
[0015.143] I> Found 42 partitions in SDMMC_USER (instance 3)
[0015.148] W> Profiler not initialized
[0015.152] I> Entering 3p server
[0015.155] I> USB configuration success
[0016.131] I> Populate chip info
[0016.171] I> Populate eeprom info
[0016.175] I> Populate eeprom info for module cvm
[0016.180]  > DEVICE_PROD: device prod is not initialized.
RATCHET: MB1 binary ratchet value 4 is larger than ratchet level 2 from HW fuses.
[0124.330] I> MB1 (prd-version: 2.3.0.0-t194-41334769-0a17edc1)
[0124.336] I> Boot-mode: RCM
[0124.338] I> Platform: Silicon
[0124.341] I> Chip revision : A02P
[0124.344] I> Bootrom patch version : 15 (correctly patched)
[0124.349] I> ATE fuse revision : 0x200
[0124.353] I> Ram repair fuse : 0x0
[0124.356] I> Ram Code : 0x2
[0124.358] I> rst_source: 0xb, rst_level: 0x1
[0124.363] I> USB configuration success
[0126.380] I> bct_bootrom image downloaded
[0126.388] W> PROD_CONFIG: device prod data is empty in MB1 BCT.
[0126.395] I> Temperature = 30000
[0126.398] W> Skipping boost for clk: BPMP_CPU_NIC
[0126.403] W> Skipping boost for clk: BPMP_APB
[0126.407] W> Skipping boost for clk: AXI_CBB
[0126.411] W> Skipping boost for clk: AON_CPU_NIC
[0126.415] W> Skipping boost for clk: CAN1
[0126.419] W> Skipping boost for clk: CAN2
[0126.423] I> Boot-device: SDMMC (instance: 3)
[0126.427] I> bct_mb1 image downloaded
[0126.437] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000
[0126.445] W>  Thermal config not found in BCT
[0126.453] W>  MEMIO rail config not found in BCT
[0126.469] C> Task 0x4d failed (err: 0x8c8c011c)
[0126.473] E> Top caller module: MB1_MSS, error module: MB1_MSS, reason: 0x1c, aux_info: 0x01
[0126.481] C> Error: 0x8c8c011c
[0126.484] C> MB1(2.3.0.0-t194-41334769-0a17edc1) BIT boot status dump :
00000000001111111110010000000000011110111111000000111111111111110011100011111000000000000000000000000000
00000000000000000000000010100000000001010000000000000101000000000010100000000000000000000000000000000000
000000000000000000000000000000000000000000000000
[0126.514]