celeron55

------Addition of New Official Games to Minetest------

The following criteria should be met by any game before it is considered for inclusion as an official game for Minetest:

1. Playable.
		To be assessed by testers. See Testing section below.
2. Enjoyable.
		To be assessed by testers. See Testing section below.

celeron55

#define DISCHARGE_SOFT_LIMIT_LOWEST_A 10
#define DISCHARGE_SOFT_LIMIT_UPPER_CELL_VOLTAGE 3.6
#define DISCHARGE_SOFT_LIMIT_LOWEST_CELL_VOLTAGE 2.9


    if(min_cell_v < DISCHARGE_SOFT_LIMIT_UPPER_CELL_VOLTAGE){
        float factor = (min_cell_v - DISCHARGE_SOFT_LIMIT_LOWEST_CELL_VOLTAGE) / (DISCHARGE_SOFT_LIMIT_UPPER_CELL_VOLTAGE - DISCHARGE_SOFT_LIMIT_LOWEST_CELL_VOLTAGE);
        if(factor < 0.0)
            factor = 0.0;
        if(factor > 1.0)

celeron55

void update_bms_discharge_motor_torque_req_limit()
{
    // Limit torque request according to bms_status.max_discharge_current_Ax10
    if(bms_status.max_discharge_current_Ax10 < 2000){
        // Calculate rough motor current limit based on motor speed, rail
        // voltage and rail current limit
        float speed_rpm = abs(inverter_status.speed / INVERTER_BITS_PER_RPM);
        float rail_voltage = inverter_status.voltage / INVERTER_BITS_PER_VOLT;
        float rail_current_per_motor_current = speed_rpm / 3000.0f;
        float rail_current_limit = (float)bms_status.max_discharge_current_Ax10 / 10.0f;

celeron55

Total 12 modules  266.03 V
* Module 1: (22.26) 3.73 3.73 3.73 3.73 3.73 3.73 V  24.2/24.1°C
* Module 2: (22.29) 3.73 3.73 3.70 3.79 3.73 3.73 V  24.3/24.0°C
* Module 3: (22.26) 3.73 3.73 3.73 3.73 3.73 3.73 V  24.0/23.9°C
* Module 4: (22.28) 3.73 3.73 3.73 3.73 3.73 3.73 V  23.9/24.0°C
* Module 5: (22.28) 3.73 3.73 3.73 3.73 3.73 3.73 V  23.8/23.7°C
* Module 6: (22.22) 3.73 3.74 3.73 3.72 3.71 3.71 V  23.8/23.7°C
* Module 7: (22.27) 3.73 3.73 3.73 3.73 3.73 3.73 V  24.0/23.9°C
* Module 8: (22.26) 3.73 3.73 3.73 3.73 3.73 3.73 V  23.8/23.8°C
* Module 9: (22.28) 3.73 3.73 3.73 3.73 3.73 3.73 V  23.9/24.0°C

celeron55

Total 1 modules  0.00 V
FAULT STATE ACTIVE
* Module 1: (0.00) 3.38 3.35 3.38 3.46 3.53 3.70 V  -98.4/-89.3°C  FAULTS: OV   ALERTS: OT1 
44.601s: 44.601s: INFO: Command: reg load overwrite
Overwriting module configuration registers
53.187s: 53.187s: INFO: Command: ls
Total 1 modules  20.96 V
* Module 1: (20.96) 3.39 3.36 3.39 3.47 3.52 3.63 V  -83.1/-89.3°C
01m02.785s: 01m02.785s: INFO: Command: eprom write 1
Writing eprom of module number 1

celeron55

10:05:12 <+selleri> tuo laturi käskyttää EVSE-piuhasta releen kiinni vaikka sille ei syötä mitään can-viestejä 
10:14:32 <+selleri> meneeköhän tuo johonkin failsafe-moodiin akkujännitteen ollessa nolla (kuten nyt on) ja se moodi 
                    on sellainen että se yrittää ladata itsenäisesti 
10:15:31 <+selleri> se ei kyllä nosta akulle jännitteen kuin 7 volttiin, ei vaikuta latausyritykseltä 
10:15:55 <+selleri> ehkä se odottaa että akulla olisi joku jännite ja sitten lataisi jos on 
10:16:15 <+selleri> ilman että se sanoo vikakoodia siitä että akun jännite on liian alhainen 
10:18:17 <+selleri> se jännite liian matala -vikakoodi on määritelty manuaalissa tulevan "during normal charging" 
10:18:25 <+selleri> ja ei ole vikakoodia joka tulisi latauksen alussa tai kun aiotaan ladata 
10:18:45 <+selleri> eli ehkä se koodi voi tulla vasta sen jälkeen kun laturi on itsekseen päättänyt että nyt voi  
                    ladata 

celeron55

Entering Configuration Mode Successful!
Setting Baudrate Successful!
Initialization ok
Available commands:
  filter <hex id>
  rmfilter <hex id>
  lsfilter
  send <hex id> <hex data>
  dtcr | dr | dtcra | dra  - Read DTCs (a: all op cycles)
  dtcc | dc  - Clear DTCs

celeron55

Entering Configuration Mode Successful!
Setting Baudrate Successful!
Initialization ok
Available commands:
  filter <hex id>
  rmfilter <hex id>
  lsfilter
  send <hex id> <hex data>
  dtcr | dr | dtcra | dra  - Read DTCs (a: all op cycles)
  dtcc | dc  - Clear DTCs

celeron55

Entering Configuration Mode Successful!
Setting Baudrate Successful!
Initialization ok
Available commands:
  filter <hex id>
  rmfilter <hex id>
  lsfilter
  send <hex id> <hex data>
  dtcr | dr | dtcra | dra  - Read DTCs (a: all op cycles)
  dtcc | dc  - Clear DTCs

celeron55

Entering Configuration Mode Successful!
Setting Baudrate Successful!
Initialization ok
Available commands:
  filter <hex id>
  rmfilter <hex id>
  lsfilter
  send <hex id> <hex data>
  dtcr | dr | dtcra | dra  - Read DTCs (a: all op cycles)
  dtcc | dc  - Clear DTCs