| smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.9.0-7-amd64] (local build) | |
| Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org | |
| === START OF INFORMATION SECTION === | |
| Model Family: Hitachi Travelstar 5K500.B | |
| Device Model: Hitachi HTS545025B9A300 | |
| Serial Number: 100203PB42061SEHSN1L | |
| LU WWN Device Id: 5 000cca 5e8e35957 | |
| Firmware Version: PB2OC60F | |
| User Capacity: 250,059,350,016 bytes [250 GB] | |
| Sector Size: 512 bytes logical/physical | |
| Rotation Rate: 5400 rpm | |
| Form Factor: 2.5 inches | |
| Device is: In smartctl database [for details use: -P show] | |
| ATA Version is: ATA8-ACS T13/1699-D revision 6 | |
| SATA Version is: SATA 2.6, 3.0 Gb/s | |
| Local Time is: Thu Dec 12 18:28:13 2019 +03 | |
| SMART support is: Available - device has SMART capability. | |
| SMART support is: Enabled | |
| === START OF READ SMART DATA SECTION === | |
| SMART overall-health self-assessment test result: PASSED | |
| General SMART Values: | |
| Offline data collection status: (0x00) Offline data collection activity | |
| was never started. | |
| Auto Offline Data Collection: Disabled. | |
| Self-test execution status: ( 0) The previous self-test routine completed | |
| without error or no self-test has ever | |
| been run. | |
| Total time to complete Offline | |
| data collection: ( 645) seconds. | |
| Offline data collection | |
| capabilities: (0x5b) SMART execute Offline immediate. | |
| Auto Offline data collection on/off support. | |
| Suspend Offline collection upon new | |
| command. | |
| Offline surface scan supported. | |
| Self-test supported. | |
| No Conveyance Self-test supported. | |
| Selective Self-test supported. | |
| SMART capabilities: (0x0003) Saves SMART data before entering | |
| power-saving mode. | |
| Supports SMART auto save timer. | |
| Error logging capability: (0x01) Error logging supported. | |
| General Purpose Logging supported. | |
| Short self-test routine | |
| recommended polling time: ( 2) minutes. | |
| Extended self-test routine | |
| recommended polling time: ( 83) minutes. | |
| SCT capabilities: (0x003d) SCT Status supported. | |
| SCT Error Recovery Control supported. | |
| SCT Feature Control supported. | |
| SCT Data Table supported. | |
| SMART Attributes Data Structure revision number: 16 | |
| Vendor Specific SMART Attributes with Thresholds: | |
| ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE | |
| 1 Raw_Read_Error_Rate 0x000b 095 095 062 Pre-fail Always - 851968 | |
| 2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0 | |
| 3 Spin_Up_Time 0x0007 208 208 033 Pre-fail Always - 1 | |
| 4 Start_Stop_Count 0x0012 098 098 000 Old_age Always - 3532 | |
| 5 Reallocated_Sector_Ct 0x0033 037 037 005 Pre-fail Always - 0 | |
| 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 | |
| 8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0 | |
| 9 Power_On_Hours 0x0012 001 001 000 Old_age Always - 69646 | |
| 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 | |
| 12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 3505 | |
| 191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0 | |
| 192 Power-Off_Retract_Count 0x0032 086 086 000 Old_age Always - 2981 | |
| 193 Load_Cycle_Count 0x0012 001 001 000 Old_age Always - 3247899 | |
| 194 Temperature_Celsius 0x0002 137 137 000 Old_age Always - 40 (Min/Max 11/54) | |
| 196 Reallocated_Event_Count 0x0032 050 050 000 Old_age Always - 2652 | |
| 197 Current_Pending_Sector 0x0022 084 084 000 Old_age Always - 1167 | |
| 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 | |
| 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 | |
| 223 Load_Retry_Count 0x000a 100 100 000 Old_age Always - 0 | |
| SMART Error Log Version: 1 | |
| ATA Error Count: 54729 (device log contains only the most recent five errors) | |
| CR = Command Register [HEX] | |
| FR = Features Register [HEX] | |
| SC = Sector Count Register [HEX] | |
| SN = Sector Number Register [HEX] | |
| CL = Cylinder Low Register [HEX] | |
| CH = Cylinder High Register [HEX] | |
| DH = Device/Head Register [HEX] | |
| DC = Device Command Register [HEX] | |
| ER = Error register [HEX] | |
| ST = Status register [HEX] | |
| Powered_Up_Time is measured from power on, and printed as | |
| DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, | |
| SS=sec, and sss=millisec. It "wraps" after 49.710 days. | |
| Error 54729 occurred at disk power-on lifetime: 4110 hours (171 days + 6 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 40 51 02 a6 ec bd e9 Error: UNC 2 sectors at LBA = 0x09bdeca6 = 163441830 | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| c8 00 08 a0 ec bd e9 08 9d+05:10:46.416 READ DMA | |
| ca 00 08 a0 2e 30 e0 08 9d+05:10:46.416 WRITE DMA | |
| ca 00 08 48 2e 30 e0 08 9d+05:10:46.416 WRITE DMA | |
| ca 00 08 30 2d 30 e0 08 9d+05:10:46.416 WRITE DMA | |
| ca 00 08 38 2c 30 e0 08 9d+05:10:46.416 WRITE DMA | |
| Error 54728 occurred at disk power-on lifetime: 4110 hours (171 days + 6 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 40 51 29 f7 ed bd e9 Error: UNC 41 sectors at LBA = 0x09bdedf7 = 163442167 | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| 25 00 40 e0 ed bd e0 08 9d+05:10:29.716 READ DMA EXT | |
| c8 00 08 40 f1 24 e5 08 9d+05:10:29.716 READ DMA | |
| c8 00 08 78 21 21 e5 08 9d+05:10:29.616 READ DMA | |
| c8 00 20 c0 15 cc e4 08 9d+05:10:29.616 READ DMA | |
| c8 00 10 d0 03 35 e5 08 9d+05:10:29.616 READ DMA | |
| Error 54727 occurred at disk power-on lifetime: 4110 hours (171 days + 6 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 40 51 32 a6 ec bd e9 Error: UNC 50 sectors at LBA = 0x09bdeca6 = 163441830 | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| 25 00 40 98 eb bd e0 08 9d+05:10:23.116 READ DMA EXT | |
| 25 00 40 70 e8 bd e0 08 9d+05:10:23.016 READ DMA EXT | |
| 25 00 40 28 e4 bd e0 08 9d+05:10:23.016 READ DMA EXT | |
| c8 00 08 98 98 f3 e8 08 9d+05:10:23.016 READ DMA | |
| c8 00 10 80 98 f3 e8 08 9d+05:10:22.916 READ DMA | |
| Error 54726 occurred at disk power-on lifetime: 4110 hours (171 days + 6 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 40 51 02 a6 ec bd e9 Error: UNC 2 sectors at LBA = 0x09bdeca6 = 163441830 | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| c8 00 08 a0 ec bd e9 08 9d+05:01:43.516 READ DMA | |
| c8 00 08 98 ec bd e9 08 9d+05:01:43.316 READ DMA | |
| c8 00 20 b0 ab bc e8 08 9d+05:01:43.216 READ DMA | |
| c8 00 20 80 ec 07 e9 08 9d+05:01:43.216 READ DMA | |
| c8 00 08 70 41 d8 e0 08 9d+05:01:43.216 READ DMA | |
| Error 54725 occurred at disk power-on lifetime: 4110 hours (171 days + 6 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 40 51 29 f7 ed bd e9 Error: UNC 41 sectors at LBA = 0x09bdedf7 = 163442167 | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| 25 00 40 e0 ed bd e0 08 9d+05:01:33.816 READ DMA EXT | |
| 27 00 00 00 00 00 e0 08 9d+05:01:33.816 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] | |
| ec 00 00 00 00 00 a0 08 9d+05:01:33.816 IDENTIFY DEVICE | |
| ef 03 46 00 00 00 a0 08 9d+05:01:33.816 SET FEATURES [Set transfer mode] | |
| 27 00 00 00 00 00 e0 08 9d+05:01:33.816 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] | |
| SMART Self-test log structure revision number 1 | |
| Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error | |
| # 1 Short offline Completed without error 00% 0 - | |
| # 2 Short offline Completed without error 00% 0 - | |
| SMART Selective self-test log data structure revision number 1 | |
| SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS | |
| 1 0 0 Not_testing | |
| 2 0 0 Not_testing | |
| 3 0 0 Not_testing | |
| 4 0 0 Not_testing | |
| 5 0 0 Not_testing | |
| Selective self-test flags (0x0): | |
| After scanning selected spans, do NOT read-scan remainder of disk. | |
| If Selective self-test is pending on power-up, resume after 0 minute delay. |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment