PrusaSlicer configuraion export: Default M2 PETG setup
# generated by PrusaSlicer 2.2.0+linux-x64 on 2021-01-01 at 13:33:03 UTC | |
avoid_crossing_perimeters = 0 | |
bed_custom_model = | |
bed_custom_texture = | |
bed_shape = -100x-125,100x-125,100x125,-100x125 | |
bed_temperature = 90 | |
before_layer_gcode = | |
between_objects_gcode = | |
bottom_fill_pattern = hilbertcurve | |
bottom_solid_layers = 3 | |
bottom_solid_min_thickness = 0 | |
bridge_acceleration = 0 | |
bridge_angle = 0 | |
bridge_fan_speed = 100 | |
bridge_flow_ratio = 1 | |
bridge_speed = 50 | |
brim_width = 0 | |
clip_multipart_objects = 1 | |
colorprint_heights = | |
complete_objects = 0 | |
cooling = 1 | |
cooling_tube_length = 5 | |
cooling_tube_retraction = 91.5 | |
default_acceleration = 0 | |
default_filament_profile = "" | |
default_print_profile = | |
deretract_speed = 0 | |
disable_fan_first_layers = 6 | |
dont_support_bridges = 1 | |
draft_shield = 0 | |
duplicate_distance = 6 | |
elefant_foot_compensation = 0 | |
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
end_gcode = ;-- PrusaSlicer End G-Code for M2 starts --\n; Ed Nisley KE4NZU - 15 November 2013\nG1 Z160 F2000 ; lower bed\nG1 X135 Y100 F30000 ; nozzle to right, bed front\nM104 S0 ; drop extruder temperature\nM140 S0 ; drop bed temperature\nM106 S0 ; bed fan off\nM84 ; disable motors\n;-- PrusaSlicer End G-Code ends --\n\n | |
ensure_vertical_shell_thickness = 1 | |
external_perimeter_extrusion_width = 0 | |
external_perimeter_speed = 50% | |
external_perimeters_first = 0 | |
extra_loading_move = -2 | |
extra_perimeters = 1 | |
extruder_clearance_height = 20 | |
extruder_clearance_radius = 20 | |
extruder_colour = "" | |
extruder_offset = 0x0 | |
extrusion_axis = E | |
extrusion_multiplier = 0.95 | |
extrusion_width = 0.4 | |
fan_always_on = 0 | |
fan_below_layer_time = 15 | |
filament_colour = #29B2B2 | |
filament_cooling_final_speed = 3.4 | |
filament_cooling_initial_speed = 2.2 | |
filament_cooling_moves = 4 | |
filament_cost = 25 | |
filament_density = 0.95 | |
filament_deretract_speed = nil | |
filament_diameter = 1.72 | |
filament_load_time = 0 | |
filament_loading_speed = 28 | |
filament_loading_speed_start = 3 | |
filament_max_volumetric_speed = 0 | |
filament_minimal_purge_on_wipe_tower = 15 | |
filament_notes = "" | |
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" | |
filament_retract_before_travel = nil | |
filament_retract_before_wipe = nil | |
filament_retract_layer_change = nil | |
filament_retract_length = nil | |
filament_retract_lift = nil | |
filament_retract_lift_above = nil | |
filament_retract_lift_below = nil | |
filament_retract_restart_extra = nil | |
filament_retract_speed = nil | |
filament_settings_id = "M2 Esun PETG" | |
filament_soluble = 0 | |
filament_toolchange_delay = 0 | |
filament_type = PET | |
filament_unload_time = 0 | |
filament_unloading_speed = 90 | |
filament_unloading_speed_start = 100 | |
filament_vendor = (Unknown) | |
filament_wipe = nil | |
fill_angle = 45 | |
fill_density = 25% | |
fill_pattern = 3dhoneycomb | |
first_layer_acceleration = 0 | |
first_layer_bed_temperature = 90 | |
first_layer_extrusion_width = 0 | |
first_layer_height = 0.25 | |
first_layer_speed = 15 | |
first_layer_temperature = 250 | |
gap_fill_speed = 25 | |
gcode_comments = 0 | |
gcode_flavor = marlin | |
gcode_label_objects = 0 | |
high_current_on_filament_swap = 0 | |
host_type = octoprint | |
infill_acceleration = 0 | |
infill_every_layers = 1 | |
infill_extruder = 1 | |
infill_extrusion_width = 0 | |
infill_first = 1 | |
infill_only_where_needed = 0 | |
infill_overlap = 15% | |
infill_speed = 60 | |
interface_shells = 0 | |
layer_gcode = | |
layer_height = 0.25 | |
machine_max_acceleration_e = 10000,5000 | |
machine_max_acceleration_extruding = 10000,1250 | |
machine_max_acceleration_retracting = 10000,1250 | |
machine_max_acceleration_x = 2500,1000 | |
machine_max_acceleration_y = 2500,1000 | |
machine_max_acceleration_z = 2500,200 | |
machine_max_feedrate_e = 10000,5000 | |
machine_max_feedrate_x = 450,200 | |
machine_max_feedrate_y = 450,200 | |
machine_max_feedrate_z = 100,30 | |
machine_max_jerk_e = 100,50 | |
machine_max_jerk_x = 25,10 | |
machine_max_jerk_y = 25,10 | |
machine_max_jerk_z = 10,5 | |
machine_min_extruding_rate = 0,0 | |
machine_min_travel_rate = 0,0 | |
max_fan_speed = 100 | |
max_layer_height = 0 | |
max_print_height = 200 | |
max_print_speed = 80 | |
max_volumetric_speed = 0 | |
min_fan_speed = 100 | |
min_layer_height = 0.1 | |
min_print_speed = 10 | |
min_skirt_length = 25 | |
notes = | |
nozzle_diameter = 0.35 | |
only_retract_when_crossing_perimeters = 1 | |
ooze_prevention = 0 | |
output_filename_format = [input_filename_base].gcode | |
overhangs = 1 | |
parking_pos_retraction = 92 | |
perimeter_acceleration = 0 | |
perimeter_extruder = 1 | |
perimeter_extrusion_width = 0 | |
perimeter_speed = 50 | |
perimeters = 3 | |
post_process = | |
print_host = | |
print_settings_id = M2 Default | |
printer_model = | |
printer_notes = | |
printer_settings_id = M2 Default | |
printer_technology = FFF | |
printer_variant = | |
printer_vendor = | |
printhost_apikey = | |
printhost_cafile = | |
raft_layers = 0 | |
remaining_times = 0 | |
resolution = 0.01 | |
retract_before_travel = 3 | |
retract_before_wipe = 0% | |
retract_layer_change = 0 | |
retract_length = 1 | |
retract_length_toolchange = 10 | |
retract_lift = 0 | |
retract_lift_above = 0 | |
retract_lift_below = 0 | |
retract_restart_extra = 0 | |
retract_restart_extra_toolchange = 0 | |
retract_speed = 60 | |
seam_position = nearest | |
serial_port = | |
serial_speed = 250000 | |
silent_mode = 1 | |
single_extruder_multi_material = 0 | |
single_extruder_multi_material_priming = 1 | |
skirt_distance = 3 | |
skirt_height = 1 | |
skirts = 3 | |
slice_closing_radius = 0.049 | |
slowdown_below_layer_time = 5 | |
small_perimeter_speed = 25% | |
solid_infill_below_area = 70 | |
solid_infill_every_layers = 0 | |
solid_infill_extruder = 1 | |
solid_infill_extrusion_width = 0 | |
solid_infill_speed = 75% | |
spiral_vase = 0 | |
standby_temperature_delta = -5 | |
start_filament_gcode = "; Filament gcode\n" | |
start_gcode = ;-- PrusaSlicer Start G-Code for M2 starts --\n; Ed Nisley KE4NZU\n; Makergear V4 hot end\n; Origin at platform center, set by MANUAL_X_HOME_POS compiled constants\n; Z-min switch at platform, must move nozzle to X=135 to clear\nG90 ; absolute coordinates\nG21 ; millimeters\nM83 ; relative extrusion distance\nM104 S[first_layer_temperature] ; start extruder heating\nM140 S[first_layer_bed_temperature] ; start bed heating\nM17 ; enable steppers\nG4 P500 ; ... wait for power up\nG92 Z0 ; set Z to zero, wherever it might be now\nG0 Z10 F1000 ; move platform downward to clear nozzle; may crash at bottom\nG28 Y ; home Y to clear plate, offset from compiled constant\nG28 X ; home X, offset from M206 X, offset from compiled constant\nG0 X135 Y0 F15000 ; move off platform to right side, center Y\nG28 Z ; home Z to platform switch, offset from M206 Z measured\nG0 Z2.0 F1000 ; get air under switch\nG0 Y-126 F10000 ; set up for priming, zig around corner\nG0 X0 ; center X\nG0 Y-124.5 ; just over platform edge\nG0 Z0 F500 ; exactly at platform\nM190 S[first_layer_bed_temperature] ; wait for bed to finish heating\nM109 S[first_layer_temperature] ; set extruder temperature and wait\nG1 E20 F300 ; prime to get pressure, generate blob on edge\nG0 Y-123 F5000 ; shear off blob\nG0 X15 F15000 ; jerk away from blob, move over surface\nG4 P500 ; pause to attach\nG1 X45 F500 ; slowly smear snot to clear nozzle\nG1 Z1.0 F2000 ; clear bed for travel\n;-- PrusaSlicer Start G-Code ends --\n | |
support_material = 0 | |
support_material_angle = 0 | |
support_material_auto = 1 | |
support_material_buildplate_only = 0 | |
support_material_contact_distance = 0.2 | |
support_material_enforce_layers = 0 | |
support_material_extruder = 1 | |
support_material_extrusion_width = 0.31 | |
support_material_interface_contact_loops = 0 | |
support_material_interface_extruder = 1 | |
support_material_interface_layers = 3 | |
support_material_interface_spacing = 0 | |
support_material_interface_speed = 100% | |
support_material_pattern = rectilinear | |
support_material_spacing = 2.5 | |
support_material_speed = 60 | |
support_material_synchronize_layers = 0 | |
support_material_threshold = 0 | |
support_material_with_sheath = 1 | |
support_material_xy_spacing = 50% | |
temperature = 250 | |
thin_walls = 1 | |
threads = 4 | |
thumbnails = | |
toolchange_gcode = | |
top_fill_pattern = hilbertcurve | |
top_infill_extrusion_width = 0 | |
top_solid_infill_speed = 50% | |
top_solid_layers = 3 | |
top_solid_min_thickness = 0 | |
travel_speed = 300 | |
use_firmware_retraction = 0 | |
use_relative_e_distances = 0 | |
use_volumetric_e = 0 | |
variable_layer_height = 1 | |
wipe = 0 | |
wipe_into_infill = 0 | |
wipe_into_objects = 0 | |
wipe_tower = 0 | |
wipe_tower_bridging = 10 | |
wipe_tower_no_sparse_layers = 0 | |
wipe_tower_rotation_angle = 0 | |
wipe_tower_width = 60 | |
wipe_tower_x = 180 | |
wipe_tower_y = 140 | |
wiping_volumes_extruders = 70,70 | |
wiping_volumes_matrix = 0 | |
xy_size_compensation = 0 | |
z_offset = 0 |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
This comment has been minimized.
More details on my blog at https://wp.me/poZKh-9HJ