C-75 boot log

gistfile1.txt

U-Boot 1.1.4 (Jun 22 2014 - 15:02:11)

ap135 - Scorpion 1.0DRAM:
sri
Scorpion 1.0
ath_ddr_initial_config(200): (32bit) ddr2 init
tap = 0x00000003
Tap (low, high) = (0x5, 0x1f)
Tap values = (0x12, 0x12, 0x12, 0x12)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 208k for U-Boot at: 87fc8000
Reserving 192k for malloc() at: 87f98000
Reserving 44 Bytes for Board Info at: 87f97fd4
Reserving 36 Bytes for Global Data at: 87f97fb0
Reserving 128k for boot params() at: 87f77fb0
Stack Pointer at: 87f77f98
Now running in RAM - U-Boot at: 87fc8000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 32 MB
*** Warning *** : PCIe WLAN Module not found !!!
In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
athrs_sgmii_res_cal: cal value = 0xe
Fetching MAC Address from 0x87feaa8c
Fetching MAC Address from 0x87feaa8c
ath_gmac_enet_initialize: reset mask:c02200
Scorpion  ----> S17 PHY *
Vlan config...
s17 phy0 register value 0x00004140
TEST: FINAL REG VAL after TX Calibration - 0x86000000
TEST: FINAL XMII VAL after RX Calibration - 0x96000000
TEST: FINAL ETH_CFG VAL after RX Calibration - 0x00000001
athrs17_reg_init: complete
: cfg1 0x80000000 cfg2 0x7335
eth0: 88:b1:e1:61:fe:5f
eth0 up
athrs17_reg_init_wan done
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 88:b1:e1:61:fe:5e
eth1 up
eth0, eth1
Setting 0x18116290 to 0x50a1a14f
Hit enter key to stop autoboot:  0
## Booting image at 9f060000 ...
   Image Name:   Linux Kernel Image
   Created:      2017-03-02  11:13:59 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1166207 Bytes =  1.1 MB
   Load Address: 80002000
   Entry Point:  80264180
   Verifying Checksum at 0x9f060040 ...OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80264180) ...
## Giving linux memsize in bytes, 134217728

Starting kernel ...

DEBUG_LOG [586] [start_kernel]
DEBUG_LOG [595] [setup_arch]
Booting QCA955x
DEBUG_LOG [492] [arch_mem_init]
DEBUG_LOG [496] [arch_mem_init]
DEBUG_LOG [499] [arch_mem_init]
DEBUG_LOG [501] [arch_mem_init]
DEBUG_LOG [506] [arch_mem_init]
DEBUG_LOG [510] [arch_mem_init]
DEBUG_LOG [514] [arch_mem_init]
DEBUG_LOG [279] [bootmem_init]
DEBUG_LOG [319] [bootmem_init]
DEBUG_LOG [347] [bootmem_init]
DEBUG_LOG [354] [bootmem_init]
DEBUG_LOG [382] [bootmem_init]
DEBUG_LOG [421] [bootmem_init]
DEBUG_LOG [427] [bootmem_init]
DEBUG_LOG [432] [bootmem_init]
DEBUG_LOG [516] [arch_mem_init]
DEBUG_LOG [518] [arch_mem_init]
DEBUG_LOG [325] [paging_init]
DEBUG_LOG [327] [paging_init]
DEBUG_LOG [335] [paging_init]
DEBUG_LOG [360] [paging_init]
DEBUG_LOG [362] [paging_init]
DEBUG_LOG [520] [arch_mem_init]
DEBUG_LOG [597] [setup_arch]
DEBUG_LOG [600] [setup_arch]
DEBUG_LOG [602] [setup_arch]
DEBUG_LOG [589] [start_kernel]
DEBUG_LOG [591] [start_kernel]
DEBUG_LOG [593] [start_kernel]
DEBUG_LOG [595] [start_kernel]
DEBUG_LOG [597] [start_kernel]
DEBUG_LOG [599] [start_kernel]
DEBUG_LOG [602] [start_kernel]
DEBUG_LOG [604] [start_kernel]
DEBUG_LOG [607] [start_kernel]
DEBUG_LOG [609] [start_kernel]
DEBUG_LOG [613] [start_kernel]
DEBUG_LOG [618] [start_kernel]
DEBUG_LOG [620] [start_kernel]
DEBUG_LOG [622] [start_kernel]
DEBUG_LOG [624] [start_kernel]
DEBUG_LOG [626] [start_kernel]
DEBUG_LOG [628] [start_kernel]
DEBUG_LOG [635] [start_kernel]
DEBUG_LOG [641] [start_kernel]
DEBUG_LOG [649] [start_kernel]
DEBUG_LOG [651] [start_kernel]
DEBUG_LOG [654] [start_kernel]
DEBUG_LOG [656] [start_kernel]
DEBUG_LOG [658] [start_kernel]
DEBUG_LOG [660] [start_kernel]
DEBUG_LOG [662] [start_kernel]
DEBUG_LOG [664] [start_kernel]
DEBUG_LOG [666] [start_kernel]
DEBUG_LOG [668] [start_kernel]
DEBUG_LOG [670] [start_kernel]
DEBUG_LOG [672] [start_kernel]
DEBUG_LOG [679] [start_kernel]
DEBUG_LOG [681] [start_kernel]
DEBUG_LOG [683] [start_kernel]
DEBUG_LOG [687] [start_kernel]
DEBUG_LOG [690] [start_kernel]
DEBUG_LOG [698] [start_kernel]
DEBUG_LOG [699] [start_kernel]
DEBUG_LOG [706] [start_kernel]
DEBUG_LOG [708] [start_kernel]
DEBUG_LOG [716] [start_kernel]
DEBUG_LOG [719] [start_kernel]
DEBUG_LOG [729] [start_kernel]
DEBUG_LOG [732] [start_kernel]
DEBUG_LOG [734] [start_kernel]
DEBUG_LOG [736] [start_kernel]
DEBUG_LOG [738] [start_kernel]
DEBUG_LOG [740] [start_kernel]
DEBUG_LOG [742] [start_kernel]
DEBUG_LOG [744] [start_kernel]
DEBUG_LOG [746] [start_kernel]
DEBUG_LOG [752] [start_kernel]
DEBUG_LOG [754] [start_kernel]
DEBUG_LOG [756] [start_kernel]
DEBUG_LOG [758] [start_kernel]
DEBUG_LOG [768] [start_kernel]
DEBUG_LOG [770] [start_kernel]
DEBUG_LOG [772] [start_kernel]
DEBUG_LOG [774] [start_kernel]
DEBUG_LOG [776] [start_kernel]
DEBUG_LOG [778] [start_kernel]
DEBUG_LOG [780] [start_kernel]
DEBUG_LOG [782] [start_kernel]
DEBUG_LOG [784] [start_kernel]
DEBUG_LOG [786] [start_kernel]
DEBUG_LOG [788] [start_kernel]
DEBUG_LOG [791] [start_kernel]
DEBUG_LOG [793] [start_kernel]
DEBUG_LOG [795] [start_kernel]
DEBUG_LOG [797] [start_kernel]
DEBUG_LOG [799] [start_kernel]
DEBUG_LOG [801] [start_kernel]
DEBUG_LOG [803] [start_kernel]
DEBUG_LOG [805] [start_kernel]
DEBUG_LOG [808] [start_kernel]
DEBUG_LOG [811] [start_kernel]
DEBUG_LOG [814] [start_kernel]
cpu apb ddr apb ath_sys_frequency: cpu 720 ddr 600 ahb 200
flash_size passed from bootloader = 32
arg 1: console=ttyS0,115200
arg 2: root=31:03
arg 3: rootfstype=jffs2
arg 4: init=/sbin/init
arg 5: mtdparts=ath-nor0:256k(u-boot),128k(uboot-env),2048k(kernel),13888k(rootfs),64k(ART);ath-nor1:16M(opt)
arg 6: mem=128M
CPU revision is: 00019750 (MIPS 74Kc)
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
 memory: 08000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00008000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00008000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ath-nor0:256k(u-boot),128k(uboot-env),2048k(kernel),13888k(rootfs),64k(ART);ath-nor1:16M(opt) mem=128M
PID hash table entries: 512 (order: 9, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 112000k/131072k available (2459k kernel code, 18884k reserved, 661k data, 168k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Console: colour dummy device 80x25
Calibrating delay loop... 359.42 BogoMIPS (lpj=718848)
Mount-cache hash table entries: 512

****************ALLOC***********************
 Packet mem: 8034f160 (0xe00000 bytes)
********************************************

NET: Registered protocol family 16
ath_pcibios_init: bus 0
ath_pcibios_init(250): PCI 0 CMD write: 0x356
registering PCI controller with io_map_base unset
ath_pcibios_init: bus 1
***** Warning PCIe 1 H/W not found !!!
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pcibios_map_irq: IRQ 75 for bus 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
fuse init (API version 7.12)
msgmni has been set to 219
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
brd: module loaded
5 cmdlinepart partitions found on MTD device ath-nor0
Creating 5 MTD partitions on "ath-nor0":
0x000000000000-0x000000040000 : "u-boot"
0x000000040000-0x000000060000 : "uboot-env"
0x000000060000-0x000000260000 : "kernel"
0x000000260000-0x000000ff0000 : "rootfs"
0x000000ff0000-0x000001000000 : "ART"
1 cmdlinepart partitions found on MTD device ath-nor1
Creating 1 MTD partitions on "ath-nor1":
0x000001000000-0x000002000000 : "opt"
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Port Status 1c000004
ath-ehci ath-ehci.0: ATH EHCI
ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: ATH EHCI
usb usb1: Manufacturer: Linux 2.6.31-dirty ehci_hcd
usb usb1: SerialNumber: platform
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Port Status 1c000000
ath-ehci1 ath-ehci1.1: ATH EHCI
ath-ehci1 ath-ehci1.1: new USB bus registered, assigned bus number 2
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci1 ath-ehci1.1: irq 3, io mem 0x1b400000
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci1 ath-ehci1.1: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: ATH EHCI
usb usb2: Manufacturer: Linux 2.6.31-dirty ehci_hcd
usb usb2: SerialNumber: platform
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
dummy_hcd dummy_hcd: USB Host+Gadget Emulator, driver 02 May 2005
dummy_hcd dummy_hcd: Dummy host controller
dummy_hcd dummy_hcd: new USB bus registered, assigned bus number 3
usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: Dummy host controller
usb usb3: Manufacturer: Linux 2.6.31-dirty dummy_hcd
usb usb3: SerialNumber: dummy_hcd
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
arch/mips/atheros/gpio.c (ath_simple_config_init) JUMPSTART_GPIO: 0
ath_simple_config_invoke_cb: sc 1, irq 0, ignorepb 1, jiffies 4294892562
enable watchdog
athwdt_init: Registering WDT success
ath_otp_init: Registering OTP success
VFS: Mounted root (jffs2 filesystem) readonly on device 31:3.
Freeing unused kernel memory: 168k freed
Warning: unable to open an initial console.
qca955x_GMAC: Length per segment 1536
955x_GMAC: qca955x_gmac_attach
955x_GMAC: qca955x_set_gmac_caps
Currently in polling mode unit0
mac:0 Registering S17....
qca955x_GMAC: RX TASKLET - Pkts per Intr:160
qca955x_GMAC: Mac address for unit 0:bfff0000
qca955x_GMAC: 88:b1:e1:61:fe:5f
qca955x_GMAC: Max segments per packet :   1
qca955x_GMAC: Max tx descriptor count :   128
qca955x_GMAC: Max rx descriptor count :   224
qca955x_GMAC: Mac capability flags    :   10002A00
955x_GMAC: qca955x_gmac_attach
955x_GMAC: qca955x_set_gmac_caps
Currently in polling mode unit1
mac:1 Registering S17....
qca955x_GMAC: RX TASKLET - Pkts per Intr:160
qca955x_GMAC: Mac address for unit 1:bfff0006
qca955x_GMAC: 88:b1:e1:61:fe:5e
qca955x_GMAC: Max segments per packet :   1
qca955x_GMAC: Max tx descriptor count :   128
qca955x_GMAC: Max rx descriptor count :   224
qca955x_GMAC: Mac capability flags    :   12002200
955x_GMAC: Serdes PLL is locked value 0x1f038116
To set s17 LOOKUP_CTRL_REG registers, flag 0
athr_gmac_ring_alloc Allocated 2048 at 0x87a1b800
sram_desc_cnt 1536,mac Unit 0,Tx r->ring_desc 0xbd000000
athr_gmac_ring_alloc Allocated 3584 at 0x87992000
sram_desc_cnt 4224,mac Unit 0,Rx r->ring_desc 0xbd000600
955x_GMAC: eth0 in RGMII MODE
Scorpion -----> S17 PHY
MC0 as SGMII
athrs17_reg_init:done
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
Phy setup Complete
To set s17 LOOKUP_CTRL_REG registers, flag 1
To set s17 LOOKUP_CTRL_REG registers, flag 0
athr_gmac_ring_alloc Allocated 2048 at 0x87a1b000
sram_desc_cnt 5760,mac Unit 1,Tx r->ring_desc 0xbd001080
athr_gmac_ring_alloc Allocated 3584 at 0x87a33000
sram_desc_cnt 8448,mac Unit 1,Rx r->ring_desc 0xbd001680
955x_GMAC: eth1 in SGMII MODE
Scorpion -----> S17 PHY
MAC6 as RGMII
athrs17_reg_init_wan done
955x_SGMII::athr_gmac_sgmii_setup  Done

rewrite SGMII_SERDES_ADDRESS register
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
Phy setup Complete
To set s17 LOOKUP_CTRL_REG registers, flag 1
NET: Registered protocol family 10
ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_UP): eth1: link is not ready
Booting in Standalone AP mode
athr_gmac_ring_free Freeing at 0x87a1b800
athr_gmac_ring_free Freeing at 0x87992000
To set s17 LOOKUP_CTRL_REG registers, flag 0
athr_gmac_ring_alloc Allocated 2048 at 0x87a1b800
sram_desc_cnt 8448,mac Unit 0,Tx r->ring_desc 0xbd000000
athr_gmac_ring_alloc Allocated 3584 at 0x87992000
sram_desc_cnt 8448,mac Unit 0,Rx r->ring_desc 0xbd000600
955x_GMAC: eth0 in RGMII MODE
Scorpion -----> S17 PHY
Error: cannot be initialized twice!
athrs17_reg_init:done
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
Phy setup Complete
To set s17 LOOKUP_CTRL_REG registers, flag 1
ADDRCONF(NETDEV_UP): eth0: link is not ready
device eth0 entered promiscuous mode
device eth0.1001 entered promiscuous mode
br0.1001: port 1(eth0.1001) entering forwarding state
led_driver: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
LED driver initializing
apmode is 1

Enet:0 port1 up
955x_GMAC: enet unit:0 is up...
eth0  RGMII  1000Mbps  full duplex
955x_GMAC: qca955x_soc_gmac_set_mac_duplex
955x_GMAC: qca955x_soc_gmac_set_link Done
955x_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
br0: port 1(eth0) entering forwarding state
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Initializing broadcast multicast optimization module****Address of trace_timer :87bd36c4
ath_hal: 0.9.17.1 (AR5416, AR9380, DEBUG, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_ahb: 10.2.2.83 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
*** All the minfree values should be <= ATH_TXBUF-32, otherwise default value will be used instead ***
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
ATH_TXBUF=512
Bootstrap clock 40MHz
Enterprise mode: 0x50000000
Restoring Cal data from Flash
Setup Background Scanning queue=1,(BK=0)
Green-AP : Green-AP : Attached

ath_get_caps[6361] rx chainmask mismatch actual 7 sc_chainmak 0
ath_get_caps[6336] tx chainmask mismatch actual 7 sc_chainmak 0
ath_attach_dfs[12855] dfsdomain 1
ATN RF Neighbor Table init done!
ath_tx_paprd_init sc 868b8000 PAPRD disabled in HAL
SC Callback Registration for wifi0
wifi0: Atheros ???: mem=0xb8100000, irq=2
ath_pci: 10.2.2.83 (Atheros/multi-bss)
ath_pci_probe
PCI device id is 003c :003c
ath_pci 0000:00:00.0: ath DEBUG: sc=0x87bb6400

 ol_ath_pci_configure : num_desired MSI set to 0

 Using PCI Legacy Interrupt
CE_per_engine_handler_adjust, base=87bb6400 offset=57400
CE_per_engine_handler_adjust, base=87bb6400 offset=57800
__ol_ath_attach: ath_attach TODO
__ol_ath_attach: dev name wifi1
ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko)
 OL_ACBKMinfree : 0
 OL_ACBEMinfree : 0
 OL_ACVIMinfree : 0
 OL_ACVOMinfree : 0
ol_ath_attach() BMI inited.
ol_ath_attach() BMI Get Target Info.
ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c
NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
ol_ath_attach() configure Target .
qc98xx_verify_checksum: flash checksum passed: 0xf317
ol_transfer_bin_file 2139: Download Flash data len 2116
ol_transfer_bin_file 2069: Download Firmware data len 228848
ol_ath_attach() Download FW.
ol_ath_attach() HT Create .
ol_ath_attach() HIF Claim.
ol_ath_attach() BMI Done.
ol_ath_attach() WMI attached. wmi_handle 865c0000
+HWT
SOC_RESET_CONTROL_ADDRESS : 800
CPU_INTR_ADDRESS = [2000000]
SOC_GLOBAL_RESET_ADDRESS = [0]
Rx_Filter : [0]
CE_per_engine_handler_adjust, base=87bb6400 offset=57400
CE_per_engine_handler_adjust, base=87bb6400 offset=57800
CE_per_engine_handler_adjust, base=87bb6400 offset=57c00
CE_per_engine_handler_adjust, base=87bb6400 offset=58000
CE_per_engine_handler_adjust, base=87bb6400 offset=58400
CE_per_engine_handler_adjust, base=87bb6400 offset=58800
CE_recv_buf_enqueue 653 Populate last entry 512 for CE 5
CE_recv_buf_enqueue 662 CE 5 wi 511 dest_ptr 0x75e980 nbytes 0 recv_ctxt 0x86528cc0
-HWT
HTC Service:0x0300 ep:1 TX flow control disabled
CE_pkt_dl_len_set CE 4 Pkt download length 64
ol_txrx_pdev_attach: 1424 tx desc's allocated ; range starts from 86670000
HTC Service:0x0100 ep:2 TX flow control disabled
wmi_service_ready_event_rx:  WMI UNIFIED SERVICE READY event
num_rf_chain : 00000003
ht_cap_info: : 0000085b
vht_cap_info : 338001b2
vht_supp_mcs : 0000ffea
LARGE_AP enabled. num_peers 126, num_vdevs 16, num_tids 220
idx 0 req 1  num_units 0 num_unit_info 2 unit size 444 actual units 127
chunk 0 len 56388 requested ,ptr  0x6680000
FIRMWARE:P 127 V 16 T 389

FIRMWARE:_wlan_rtt_enable
wmi_ready_event_rx:  WMI UNIFIED READY event
ol_ath_connect_htc() WMI is ready
ol_ath_set_host_app_area TODO
target uses HTT version 2.1; host uses 2.1
ol_ath_attach() connect HTC.
bypasswmi : 0
ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
Add VHT80 channel: 5210
Add VHT80 channel: 5290
Add VHT80 channel: 5530
Add VHT80 channel: 5610
Add VHT80 channel: 5690
Add VHT80 channel: 5775
Skipping VHT80 channel 5825
ol_ath_phyerr_attach: called
OL Resmgr Init-ed
Green-AP : Green-AP : Attached

Green-AP : Attached
ol_if_dfs_setup: called
ol_if_dfs_attach: called; ptr=8666d974, radar_info=87b73bf8
ol_ath_rtt_meas_report_attach: called
ol_scan_update_channel_list: 0 channel 052 flags 00800300 info 0000188a
ol_scan_update_channel_list: 1 channel 056 flags 00800300 info 0000188a
ol_scan_update_channel_list: 2 channel 060 flags 00800300 info 0000188a
ol_scan_update_channel_list: 3 channel 064 flags 00800300 info 0000188a
ol_scan_update_channel_list: 4 channel 036 flags 00800100 info 0000180a
ol_scan_update_channel_list: 5 channel 040 flags 00800100 info 0000180a
ol_scan_update_channel_list: 6 channel 044 flags 00800100 info 0000180a
ol_scan_update_channel_list: 7 channel 048 flags 00800100 info 0000180a
ol_scan_update_channel_list: 8 channel 034 flags 00010100 info 00000804
ol_scan_update_channel_list: 9 channel 038 flags 00010100 info 00000804
ol_scan_update_channel_list: 10 channel 042 flags 00010100 info 00000804
ol_scan_update_channel_list: 11 channel 046 flags 00010100 info 00000804
ol_scan_update_channel_list: 12 channel 144 flags 00800300 info 0000188a
ol_scan_update_channel_list: 13 channel 149 flags 00800100 info 0000180a
ol_scan_update_channel_list: 14 channel 153 flags 00800100 info 0000180a
ol_scan_update_channel_list: 15 channel 157 flags 00800100 info 0000180a
ol_scan_update_channel_list: 16 channel 161 flags 00800100 info 0000180a
ol_scan_update_channel_list: 17 channel 165 flags 00100100 info 00001808
ol_scan_update_channel_list: 18 channel 100 flags 00800300 info 0000188a
ol_scan_update_channel_list: 19 channel 104 flags 00800300 info 0000188a
ol_scan_update_channel_list: 20 channel 108 flags 00800300 info 0000188a
ol_scan_update_channel_list: 21 channel 112 flags 00800300 info 0000188a
ol_scan_update_channel_list: 22 channel 116 flags 00800300 info 0000188a
ol_scan_update_channel_list: 23 channel 120 flags 00800300 info 0000188a
ol_scan_update_channel_list: 24 channel 124 flags 00800300 info 0000188a
ol_scan_update_channel_list: 25 channel 128 flags 00800300 info 0000188a
ol_scan_update_channel_list: 26 channel 132 flags 00800300 info 0000188a
ol_scan_update_channel_list: 27 channel 136 flags 00800300 info 0000188a
ol_scan_update_channel_list: 28 channel 140 flags 00800300 info 0000188a
ol_scan_update_channel_list: 29 channel 208 flags 00010100 info 00000804
ol_scan_update_channel_list: 30 channel 212 flags 00010100 info 00000804
ol_scan_update_channel_list: 31 channel 216 flags 00010100 info 00000804
ol_scan_update_channel_list: 32 channel 184 flags 00010100 info 00000804
ol_scan_update_channel_list: 33 channel 188 flags 00010100 info 00000804
ol_scan_update_channel_list: 34 channel 192 flags 00010100 info 00000804
ol_scan_update_channel_list: 35 channel 196 flags 00010100 info 00000804
ol_scan_update_channel_list: 36 channel 169 flags 00010100 info 00000804
ol_scan_update_channel_list: 37 channel 173 flags 00010100 info 00000804
ol_ath_attach() UMAC attach .
ol_ath_attach: Calling ol_if_dfs_configure
__ol_ath_attach: init tx/rx TODO
__ol_ath_attach: hard_header_len reservation 58
SC Callback Registration for wifi1
Initializing Pktlogs for 11ac
ath_attach_dfs[12855] dfsdomain 1
isCountryCodeValid: EEPROM regdomain 0x0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
Add VHT80 channel: 5210
Add VHT80 channel: 5290
Add VHT80 channel: 5530
Add VHT80 channel: 5610
Add VHT80 channel: 5690
Add VHT80 channel: 5775
Skipping VHT80 channel 5825
ol_scan_update_channel_list: 0 channel 052 flags 00800300 info 0000188a
ol_scan_update_channel_list: 1 channel 056 flags 00800300 info 0000188a
ol_scan_update_channel_list: 2 channel 060 flags 00800300 info 0000188a
ol_scan_update_channel_list: 3 channel 064 flags 00800300 info 0000188a
ol_scan_update_channel_list: 4 channel 036 flags 00800100 info 0000180a
ol_scan_update_channel_list: 5 channel 040 flags 00800100 info 0000180a
ol_scan_update_channel_list: 6 channel 044 flags 00800100 info 0000180a
ol_scan_update_channel_list: 7 channel 048 flags 00800100 info 0000180a
ol_scan_update_channel_list: 8 channel 034 flags 00010100 info 00000804
ol_scan_update_channel_list: 9 channel 038 flags 00010100 info 00000804
ol_scan_update_channel_list: 10 channel 042 flags 00010100 info 00000804
ol_scan_update_channel_list: 11 channel 046 flags 00010100 info 00000804
ol_scan_update_channel_list: 12 channel 144 flags 00800300 info 0000188a
ol_scan_update_channel_list: 13 channel 149 flags 00800100 info 0000180a
ol_scan_update_channel_list: 14 channel 153 flags 00800100 info 0000180a
[wifi1] FWLOG: [97980] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x460, 0x460, 0x0 )
[wifi1] FWLOG: [97980] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x460, 0x460, 0x0 )
[wifi1] FWLOG: [97980] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x460, 0x460, 0x0 )
[wifi1] FWLOG: [97980] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x460, 0x460, 0x0 )
[wifi1] FWLOG: [97985] WHAL_ERROR_RECV_STOPPCU ( 0x110298a, 0x3 )
[wifi1] FWLOG: [97985] WHAL_ERROR_RESET_PM (  )
[wifi1] FWLOG: [98381] ANI Enable:  1
ol_scan_update_channel_list: 15 channel 157 flags 00800100 info 0000180a
ol_scan_update_channel_list: 16 channel 161 flags 00800100 info 0000180a
ol_scan_update_channel_list: 17 channel 165 flags 00100100 info 00001808
ol_scan_update_channel_list: 18 channel 100 flags 00800300 info 0000188a
ol_scan_update_channel_list: 19 channel 104 flags 00800300 info 0000188a
ol_scan_update_channel_list: 20 channel 108 flags 00800300 info 0000188a
ol_scan_update_channel_list: 21 channel 112 flags 00800300 info 0000188a
ol_scan_update_channel_list: 22 channel 116 flags 00800300 info 0000188a
ol_scan_update_channel_list: 23 channel 120 flags 00800300 info 0000188a
ol_scan_update_channel_list: 24 channel 124 flags 00800300 info 0000188a
ol_scan_update_channel_list: 25 channel 128 flags 00800300 info 0000188a
ol_scan_update_channel_list: 26 channel 132 flags 00800300 info 0000188a
ol_scan_update_channel_list: 27 channel 136 flags 00800300 info 0000188a
ol_scan_update_channel_list: 28 channel 140 flags 00800300 info 0000188a
ol_scan_update_channel_list: 29 channel 208 flags 00010100 info 00000804
ol_scan_update_channel_list: 30 channel 212 flags 00010100 info 00000804
ol_scan_update_channel_list: 31 channel 216 flags 00010100 info 00000804
ol_scan_update_channel_list: 32 channel 184 flags 00010100 info 00000804
ol_scan_update_channel_list: 33 channel 188 flags 00010100 info 00000804
ol_scan_update_channel_list: 34 channel 192 flags 00010100 info 00000804
ol_scan_update_channel_list: 35 channel 196 flags 00010100 info 00000804
ol_scan_update_channel_list: 36 channel 169 flags 00010100 info 00000804
ol_scan_update_channel_list: 37 channel 173 flags 00010100 info 00000804
wlan_vap_create : enter. devhandle=0x868502c0, opmode=IEEE80211_M_HOSTAP, flags=0x8001
wlan_vap_create : exit. devhandle=0x868502c0, opmode=IEEE80211_M_HOSTAP, flags=0x8001.
VAP device mon0 created osifp: (8673d2c0) os_if: (8686c000)
initialise_atn_info: Initialising background scanning.
mon0: atn_init DONE
ath_ioctl: SIOC80211IFCREATE CALLED
wmi_unified_vdev_create_send: ID = 8 VAP Addr = 88:b1:e1:61:fe:58:
VAP device mon1 created osifp: (8687fac0) os_if: (86774000)
initialise_atn_info: Initialising background scanning.
mon1: atn_init DONE
Initialising Reset Sensor module
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
GRE over IPv4 tunneling driver
Registering the character device successfull 254
Registering Iptalbe WCMASK module
GRE over IPv6 tunneling driver
 ip6gre_init_net GRE over IPv6 tunneling driver 1.1
 ip6gre_init_net GRE over IPv6 tunneling driver 1.2 ip6gre_net_id[5]
 ip6gre_init_net GRE over IPv6 tunneling driver 1.3
 ip6gre_init_net GRE over IPv6 tunneling driver 1.4
 ip6gre_init_net GRE over IPv6 tunneling driver 1.5
 ip6gre_init_net GRE over IPv6 tunneling driver 1.6
 ip6gre_init_net GRE over IPv6 tunneling driver 1.7
 ip6gre_init_net GRE over IPv6 tunneling driver 1.8
u32 classifier
    Actions configured
Mirror/redirect action on
wifi0 DCS for CW interference mitigation:   0
wifi0 DCS for WLAN interference mitigation: 0
wifi0: ieee80211_acs_set_param 2176 disabling DCS sleep timer (if it was running)
wifi1 OL DCS for CW interference mitigation:   0
wifi1 OL DCS for WLAN interference mitigation: 0
wifi1: ieee80211_acs_set_param 2176 disabling DCS sleep timer (if it was running)
mon0: ATN_IOCTL: param=414
Sensor Integrity Check: [PASSED]

 (none) mips #1 Thu Mar 2 16:43:33 IST 2017 (none)
(

gistfile2.txt

ACS: Init First boot Acs
------------[ cut here ]------------
WARNING: at kernel/softirq.c:143 local_bh_enable+0x90/0xec()
Modules linked in:
 ifb act_police act_mirred sch_htb sch_tbf sch_ingress cls_u32 ip6_gre ip6_tunnel tunnel6 iptable_WCMASK xt_CONNMARK xt_connmark iptable_PKT_MANGLE(P) nf_nat_pptp nf_nat_proto_gre nf_conntrack_pptp nf_conntrack_proto_gre iptable_CONTANALYTICS(P) ip_gre xt_physdev xt_mark ipt_MASQUERADE ipt_REDIRECT iptable_nat nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 ipt_REJECT iptable_mangle iptable_filter ip_tables xt_conntrack xt_state nf_conntrack_ftp nf_conntrack nfnetlink_queue xt_tcpudp xt_multiport xt_mac xt_NFQUEUE xt_MARK x_tables nfnetlink reset_sensor(P) ath_pktlog(P) umac ath_dev(P) ath_dfs(P) ath_rate_atheros(P) ath_hal(P) asf(P) adf(P) broadcast_multicast_opt(P) led_driver(P) ipv6 athrs_gmac
Call Trace:
[<80267af8>] dump_stack+0x8/0x34
[<80027690>] warn_slowpath_common+0x70/0xb0
[<8002d9e4>] local_bh_enable+0x90/0xec
[<8594e260>] atn_apc_packet_handler+0x1f4/0xa54 [umac]
[<858259a0>] atn_bgscan_rx_proc+0x570/0xe4c [umac]
[<8689cbd8>] atn_bgscan_tx+0x90/0xf0 [ath_dev]
[<86883ff8>] ath_beacon_tasklet+0x3d8/0xad0 [ath_dev]
[<858c0884>] ath_intr_aponly+0x45c/0x5ac [umac]
[<858c0a04>] ath_isr_aponly+0x30/0x118 [umac]
[<80051124>] handle_IRQ_event+0x90/0x17c
[<80052d28>] handle_percpu_irq+0x48/0xb4
[<80006268>] ath_dispatch_wlan_intr+0x68/0xe0
[<80006aac>] ret_from_irq+0x0/0x4

---[ end trace 91056aebe0d39233 ]---