Skip to content

Instantly share code, notes, and snippets.

Embed
What would you like to do?
pfSense software 2.4.3 on espresso.bin (now booting from SD card)
NOTICE: Booting Trusted Firmware
NOTICE: BL1: v1.3(debug):armada-17.06.2:297d68f
NOTICE: BL1: Built : 11:01:44, Jan 9 2NOTICE: BL2: v1.3(debug):armada-17.06.2:297d68f
NOTICE: BL2: Built : 11:01:47, Jan 9 2018NOTICE: BL31: v1.3(debug):armada-17.06.2:297d68f
NOTICE: BL31:
U-Boot 2017.03-armada-17.06.3-ga33ecb8-dirty (Jan 09 2018 - 10:56:45 -0200)
Model: Marvell Armada 3720 Community Board ESPRESSOBin
CPU @ 1000 [MHz]
L2 @ 800 [MHz]
TClock @ 200 [MHz]
DDR @ 800 [MHz]
DRAM: 2 GiB
U-Boot DComphy-0: USB3 5 Gbps
Comphy-1: PEX0 2.5 Gbps
Comphy-2: SATA0 6 Gbps
SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: ncq led only pmp fbss pio slum part sxs
PCIE-0: Link down
MMC: sdhci@d0000: 0
SF: Detected w25q32dw with page size 256 Bytes, erase size 4 KiB, total 4 MiB
Net:
Warning: neta@30000 (eth0) using random MAC address - f2:42:9f:a5:0a:72
eth0: neta@30000 [PRIME]
Hit any key to stop autoboot: 0
reading /boot/dtb/armada-3720-espressobin.dtb
12313 bytes read in 24 ms (501 KiB/s)
reading efi/boot/bootaa64.efi
393216 bytes read in 31 ms (12.1 MiB/s)
## Starting EFI application at 00200000 ...
Scanning disk sdhci@d0000.blk...
Found 4 disks
>> FreeBSD EFI boot block
Loader path: /boot/loader.efi
Initializing modules: ZFS UFS
Probing 4 block devices......* done
ZFS found no pools
UFS found 1 partition
Consoles: EFI console
Command line arguments: loader.efi
Image base: 0x7c99f008
EFI version: 2.05
EFI Firmware: Das U-boot (rev 0.00)
FreeBSD/arm64 EFI loader, Revision 1.1
(Fri Feb 9 17:22:38 CST 2018 root@buildbot2.netgate.com)
EFI boot environment
Loading /boot/defaults/loader.conf
/boot/kernel/kernel text=0x9502f0 data=0x872038+0x39b2f6 syms=[0x8+0x110790+0x8+0xea987]
|
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
Using DTB provided by EFI at 0x8000000.
Copyright (c) 1992-2017 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.1-RELEASE-p6 #0 r313908+93ca43746b4(factory-RELENG_2_4): Fri Feb 9 17:24:30 CST 2018
root@buildbot2.netgate.com:/xbuilder/crossbuild-master/work/aarch64/obj/M6UEwngT/arm64.aarch64/xbuilder/crossbuild-master/pfSense/tmp/FreeBSD-src/sys/pfSense arm64
FreeBSD clang version 4.0.0 (tags/RELEASE_400/final 297347) (based on LLVM 4.0.0)
VT: init without driver.
Starting CPU 1 (1)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
random: entropy device external interface
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffff00000016151c, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffff0000001615c8, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffff000000161674, 0) error 1
wlan: mac acl policy registered
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xffff000000161720, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffff0000001617cc, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffff000000161878, 0) error 1
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
simplebus1: <Flattened device tree simple bus> on simplebus0
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
gic0: <ARM Generic Interrupt Controller v3.0> mem 0x1d00000-0x1d0ffff,0x1d40000-0x1d7ffff,0x1d80000-0x1d81fff,0x1d90000-0x1d91fff,0x1da0000-0x1dbffff irq 21 on simplebus1
generic_timer0: <ARMv8 Generic Timer> irq 0,1,2,3 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 12500000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 12500000 Hz quality 1000
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpu1: <Open Firmware CPU> on cpulist0
pmu0: <Performance Monitoring Unit> irq 4 on ofwbus0
uart0: <Marvell Armada 3700 UART> mem 0x12000-0x121ff irq 9,10,11 on simplebus1
uart0: console (115200,n,8,1)
mvneta0: <NETA controller> mem 0x30000-0x33fff irq 14 on simplebus1
mvneta0: version is 10
mvneta0: Ethernet address: f4:81:38:b4:8a:00
mdio0: <MDIO> on mvneta0
e6000sw0: <Marvell 88E6341> on mdio0
e6000sw0: multi-chip addressing mode
e6000sw0: CPU port at 0
e6000sw0: fixed port at 0
e6000sw0: PHY at port 1
miibus0: <MII bus> on e6000sw0
e1000phy0: <Marvell 88E1000 Gigabit PHY> PHY 17 on miibus0
e1000phy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 2
miibus1: <MII bus> on e6000sw0
e1000phy1: <Marvell 88E1000 Gigabit PHY> PHY 18 on miibus1
e1000phy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: PHY at port 3
miibus2: <MII bus> on e6000sw0
e1000phy2: <Marvell 88E1000 Gigabit PHY> PHY 19 on miibus2
e1000phy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
e6000sw0: switch is ready.
etherswitch0: <Switch controller> on e6000sw0
xhci0: <Marvell Integrated USB 3.0 controller> mem 0x58000-0x5bfff irq 16 on simplebus1
xhci0: 32 bytes context size, 32-bit DMA
usbus0 on xhci0
ehci0: <Marvell Integrated USB 2.0 controller> mem 0x5e000-0x5ffff irq 17 on simplebus1
usbus1: EHCI version 1.0
usbus1 on ehci0
sdhci_xenon0: <Armada Xenon SDHCI controller> mem 0xd0000-0xd02ff,0x1e808-0x1e80b irq 18 on simplebus1
mmc0: <MMC/SD bus> on sdhci_xenon0
ahci0: <AHCI SATA controller> mem 0xe0000-0xe1fff irq 20 on simplebus1
ahci0: AHCI v1.30 with 1 6Gbps ports, Port Multiplier supported with FBS
ahcich0: <AHCI channel> at channel 0 on ahci0
cryptosoft0: <software crypto>
Timecounters tick every 1.000 msec
mvneta0: link state changed to UP
e6000sw0port1: link state changed to DOWN
e6000sw0port2: link state changed to DOWN
e6000sw0port3: link state changed to DOWN
usbus0: 5.0Gbps Super Speed USB v3.0
usbus1: 480Mbps High Speed USB v2.0
ugen0.1: <Marvell XHCI root HUB> at usbus0
uhub0: <Marvell XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
ugen1.1: <Marvell EHCI root HUB> at usbus1
uhub1: <Marvell EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
mmcsd0: 8GB <SDHC SS08G 8.0 SN 5D33074C MFG 12/2015 by 3 SD> at mmc0 50.0MHz/4bit/65535-block
uhub0: 2 ports with 2 removable, self powered
uhub1: 1 port with 1 removable, self powered
e6000sw0port1: link state changed to UP
Release APs
APs not started
taskqgroup_adjust failed cnt: 2 stride: 1 mp_ncpus: 2 smp_started: 0
taskqgroup_adjust failed cnt: 1 stride: 1 mp_ncpus: 2 smp_started: 0
Trying to mount root from ufs:/dev/ufsid/5a7e2f0a18ee6324 [rw,noatime]...
warning: no time-of-day clock registered, system time will not be set accurately
Configuring crash dumps...
No suitable dump device was found.
Growing root partition to fill device
mmcsd0s3 resized
super-block backups (for fsck_ffs -b #) at:
1953472, 2441792, 2930112, 3418432, 3906752, 4395072, 4883392, 5371712,
5860032, 6348352, 6836672, 7324992, 7813312, 8301632, 8789952, 9278272,
9766592, 10254912, 10743232, 11231552, 11719872, 12208192, 12696512, 13184832,
13673152, 14161472, 14649792, 15138112
/dev/ufsid/5a7e2f0a18ee6324: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ufsid/5a7e2f0a18ee6324: clean, 1654582 free (62 frags, 206815 blocks, 0.0% fragmentation)
Filesystems are clean, continuing...
Mounting filesystems...
random: unblocking device.
__
_ __ / _|___ ___ _ __ ___ ___
| '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \
| |_) | _\__ \ __/ | | \__ \ __/
| .__/|_| |___/\___|_| |_|___/\___|
|_|
Welcome to pfSense 2.4.3-DEVELOPMENT...
...ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/lib/ipsec /usr/local/lib/perl5/5.24/mach/CORE
done.
External config loader 1.0 is now starting... mmcsd0s1 mmcsd0s2 mmcsd0s3
Launching the init system....... done.
Initializing.................. done.
Starting device manager (devd)...done.
Loading configuration......done.
Updating configuration........................done.
Checking config backups consistency...done.
Setting up extended sysctls...done.
Setting timezone...done.
Configuring loopback interface...done.
Starting syslog...done.
Starting Secure Shell Services...done.
Configuring switch...done.
Setting up interfaces microcode...done.
Configuring loopback interface...done.
Creating wireless clone interfaces...done.
Configuring LAGG interfaces...done.
Configuring VLAN interfaces...done.
Configuring QinQ interfaces...done.
Configuring WAN interface...done.
Configuring LAN interface...done.
Configuring CARP settings...done.
Syncing OpenVPN settings...done.
Configuring firewall......done.
Starting PFLOG...done.
Setting up gateway monitors...done.
Setting up static routes...done.
Setting up DNSs...Starting DNS Resolver...done.
done.
Synchronizing user settings...done.
Starting webConfigurator...done.
Configuring CRON...done.
Starting NTP time client...done.
Starting DHCP service...done.
Starting DHCPv6 service...done.
Configuring firewall......done.
Generating RRD graphs...done.
Starting syslog...done.
Starting CRON... done.
pfSense 2.4.3-DEVELOPMENT arm64 Fri Feb 09 17:06:44 CST 2018
Bootup complete
FreeBSD/arm64 (pfSense.localdomain) (ttyu0)
Marvell Armada 3700 - Netgate Device ID: ed5d2878c9371dc449d8
*** Welcome to pfSense 2.4.3-DEVELOPMENT (arm64) on pfSense ***
WAN (wan) -> mvneta0.4090 -> v4/DHCP4: 192.168.0.150/24
LAN (lan) -> mvneta0.4091 -> v4: 192.168.1.1/24
0) Logout (SSH only) 9) pfTop
1) Assign Interfaces 10) Filter Logs
2) Set interface(s) IP address 11) Restart webConfigurator
3) Reset webConfigurator password 12) PHP shell + pfSense tools
4) Reset to factory defaults 13) Update from console
5) Reboot system 14) Enable Secure Shell (sshd)
6) Halt system 15) Restore recent configuration
7) Ping host 16) Restart PHP-FPM
8) Shell
Enter an option: 8
[2.4.3-DEVELOPMENT][root@pfSense.localdomain]/root: ifconfig
mvneta0: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM>
ether f4:81:38:b4:8a:00
hwaddr f4:81:38:b4:8a:00
inet6 fe80::f681:38ff:feb4:8a00%mvneta0 prefixlen 64 scopeid 0x1
media: Ethernet 1000baseT <full-duplex>
status: active
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
enc0: flags=0<> metric 0 mtu 1536
groups: enc
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x7
inet 127.0.0.1 netmask 0xff000000
groups: lo
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
pfsync0: flags=0<> metric 0 mtu 1500
syncpeer: 224.0.0.240 maxupd: 128 defer: on
syncok: 1
groups: pfsync
pflog0: flags=100<PROMISC> metric 0 mtu 33160
groups: pflog
mvneta0.4090: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=3<RXCSUM,TXCSUM>
ether f4:81:38:b4:8a:00
inet6 fe80::f681:38ff:feb4:8a00%mvneta0.4090 prefixlen 64 scopeid 0xa
inet 192.168.0.150 netmask 0xffffff00 broadcast 192.168.0.255
groups: vlan
vlan: 4090 vlanpcp: 0 parent interface: mvneta0
media: Ethernet 1000baseT <full-duplex>
status: active
nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>
mvneta0.4091: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=3<RXCSUM,TXCSUM>
ether f4:81:38:b4:8a:00
inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255
inet6 fe80::1:1%mvneta0.4091 prefixlen 64 scopeid 0xb
groups: vlan
vlan: 4091 vlanpcp: 0 parent interface: mvneta0
media: Ethernet 1000baseT <full-duplex>
status: active
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
[2.4.3-DEVELOPMENT][root@pfSense.localdomain]/root: etherswitchcfg
etherswitch0: VLAN mode: DOT1Q
port0:
pvid: 1
flags=1<CPUPORT>
media: Ethernet 1000baseT <full-duplex>
status: active
port1:
pvid: 4090
flags=0<>
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
port2:
pvid: 4091
flags=0<>
media: Ethernet autoselect (none)
status: no carrier
port3:
pvid: 4091
flags=0<>
media: Ethernet autoselect (none)
status: no carrier
vlangroup0:
vlan: 1
members 0
vlangroup1:
vlan: 4090
members 0t,1
vlangroup2:
vlan: 4091
members 0t,2,3
[2.4.3-DEVELOPMENT][root@pfSense.localdomain]/root:
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment
You can’t perform that action at this time.