flashforge.g

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Sun Aug 25 2019 01:45:40 GMT-0400 (Eastern Daylight Time)

; General preferences
G90                                                ; Send absolute coordinates...
M83                                                ; ...but relative extruder moves

; Network
M550 P"Flashforge"                                 ; Set machine name
M552 S1                                            ; Enable network
M587 S"IceIceBaby" P"vanilla1c3" ; Configure access point. You can delete this line once connected
M586 P0 S1                                         ; Enable HTTP
M586 P1 S0                                         ; Disable FTP
M586 P2 S1                                         ; Disable Telnet

; Drives
M569 P0 S1                                         ; Physical drive 0 goes forwards
M569 P1 S1                                         ; Physical drive 1 goes forwards
M569 P2 S0                                         ; Physical drive 2 goes backwards
M569 P3 S0                                         ; Physical drive 3 goes forwards
M569 P4 S1                                         ; Physical drive 4 goes forwards
M584 X0 Y1 Z2 E3:4                                 ; set drive mapping
M350 X16 Y16 I1                                      ; Configure microstepping without interpolation
M350 Z16 E16:16 I1                                 ; Configure microstepping with interpolation
M92 X94.12 Y94.12 Z400.00 E96.28:96.28             ; Set steps per mm
M566 X900.00 Y900.00 Z180.00 E1200.00:1200.00      ; Set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z180.00 E1560.00:1560.00 ; Set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z150.00 E2000.00:2000.00    ; Set accelerations (mm/s^2)
M906 X600 Y600 Z600 E600:600 I30                  ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; Set axis minima
M208 X227 Y148 Z150 S0                             ; Set axis maxima

; Endstops
M574 X2 Y2 Z1 S0                                   ; Set active low endstops

; Z-Probe
M558 P0 H5 F120 T6000                              ; Disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:148 S20                           ; Define mesh grid

; Heaters
M307 H0 B0 S1.00                                  ; disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100900 B4230 R4700 L0 H0                  ; Set thermistor + ADC parameters for heater 0
M143 H0 S120                                       ; Set temperature limit for heater 0 to 120C
M305 P1 X150                                       ; Configure thermocouple for heater 1
M143 H1 S280                                       ; Set temperature limit for heater 1 to 280C
M305 P2 X151                                       ; Configure thermocouple for heater 2
M143 H2 S280                                       ; Set temperature limit for heater 2 to 280C

; Fans
M106 P0 S1 I0 F500 H1 T75                         ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H2 T75                         ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S0 I0 F500 H-1                            ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0 S"Left"                                 ; define tool 0
G10 P0 X0 Y0 Z0                                   ; set tool 0 axis offsets
G10 P0 R0 S0                                      ; set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H2 F1 S"Right"                                 ; define tool 1
G10 P1 X0 Y0 Z0                                   ; set tool 1 axis offsets
G10 P1 R0 S0                                      ; set initial tool 1 active and standby temperatures to 0C

; Automatic power saving
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Custom settings are not configured

; Miscellaneous
M501                                               ; Load saved parameters from non-volatile memory
T0                                                ; select first tool