-
-
Save numinit/91ccef5be625808d28953be3e64348eb to your computer and use it in GitHub Desktop.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.14.83] (local build) | |
| Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org | |
| === START OF INFORMATION SECTION === | |
| Model Family: Western Digital Red | |
| Device Model: WDC WD40EFRX-68N32N0 | |
| Serial Number: WD-redact | |
| LU WWN Device Id: 5 0014ee 2ba917268 | |
| Firmware Version: 82.00A82 | |
| User Capacity: 4,000,787,030,016 bytes [4.00 TB] | |
| Sector Sizes: 512 bytes logical, 4096 bytes physical | |
| Rotation Rate: 5400 rpm | |
| Form Factor: 3.5 inches | |
| Device is: In smartctl database [for details use: -P show] | |
| ATA Version is: ACS-3 T13/2161-D revision 5 | |
| SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) | |
| SMART support is: Available - device has SMART capability. | |
| SMART support is: Enabled | |
| === START OF READ SMART DATA SECTION === | |
| SMART overall-health self-assessment test result: FAILED! | |
| Drive failure expected in less than 24 hours. SAVE ALL DATA. | |
| See vendor-specific Attribute list for failed Attributes. | |
| General SMART Values: | |
| Offline data collection status: (0x02) Offline data collection activity | |
| was completed without error. | |
| Auto Offline Data Collection: Disabled. | |
| Self-test execution status: ( 0) The previous self-test routine completed | |
| without error or no self-test has ever | |
| been run. | |
| Total time to complete Offline | |
| data collection: (44040) seconds. | |
| Offline data collection | |
| capabilities: (0x7b) SMART execute Offline immediate. | |
| Auto Offline data collection on/off support. | |
| Suspend Offline collection upon new | |
| command. | |
| Offline surface scan supported. | |
| Self-test supported. | |
| Conveyance Self-test supported. | |
| Selective Self-test supported. | |
| SMART capabilities: (0x0003) Saves SMART data before entering | |
| power-saving mode. | |
| Supports SMART auto save timer. | |
| Error logging capability: (0x01) Error logging supported. | |
| General Purpose Logging supported. | |
| Short self-test routine | |
| recommended polling time: ( 2) minutes. | |
| Extended self-test routine | |
| recommended polling time: ( 467) minutes. | |
| Conveyance self-test routine | |
| recommended polling time: ( 5) minutes. | |
| SCT capabilities: (0x303d) SCT Status supported. | |
| SCT Error Recovery Control supported. | |
| SCT Feature Control supported. | |
| SCT Data Table supported. | |
| SMART Attributes Data Structure revision number: 16 | |
| Vendor Specific SMART Attributes with Thresholds: | |
| ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE | |
| 1 Raw_Read_Error_Rate 0x002f 188 188 051 Pre-fail Always - 1480 | |
| 3 Spin_Up_Time 0x0027 202 182 021 Pre-fail Always - 4883 | |
| 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 7 | |
| 5 Reallocated_Sector_Ct 0x0033 133 133 140 Pre-fail Always FAILING_NOW 1963 | |
| 7 Seek_Error_Rate 0x002e 196 194 000 Old_age Always - 416 | |
| 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 625 | |
| 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 | |
| 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 | |
| 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 7 | |
| 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 2 | |
| 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 47 | |
| 194 Temperature_Celsius 0x0022 105 101 000 Old_age Always - 45 | |
| 196 Reallocated_Event_Count 0x0032 166 166 000 Old_age Always - 34 | |
| 197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 65526 | |
| 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 | |
| 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 | |
| 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 | |
| SMART Error Log Version: 1 | |
| ATA Error Count: 128 (device log contains only the most recent five errors) | |
| CR = Command Register [HEX] | |
| FR = Features Register [HEX] | |
| SC = Sector Count Register [HEX] | |
| SN = Sector Number Register [HEX] | |
| CL = Cylinder Low Register [HEX] [23/1887] | |
| CH = Cylinder High Register [HEX] | |
| DH = Device/Head Register [HEX] | |
| DC = Device Command Register [HEX] | |
| ER = Error register [HEX] | |
| ST = Status register [HEX] | |
| Powered_Up_Time is measured from power on, and printed as | |
| DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, | |
| SS=sec, and sss=millisec. It "wraps" after 49.710 days. | |
| Error 128 occurred at disk power-on lifetime: 615 hours (25 days + 15 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 04 61 02 00 00 00 a0 Device Fault; Error: ABRT | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| ef 10 02 00 00 00 a0 08 00:01:14.464 SET FEATURES [Enable SATA feature] | |
| ec 00 00 00 00 00 a0 08 00:01:14.464 IDENTIFY DEVICE | |
| ef 03 46 00 00 00 a0 08 00:01:14.464 SET FEATURES [Set transfer mode] | |
| ef 10 02 00 00 00 a0 08 00:01:14.464 SET FEATURES [Enable SATA feature] | |
| ec 00 00 00 00 00 a0 08 00:01:14.463 IDENTIFY DEVICE | |
| Error 127 occurred at disk power-on lifetime: 615 hours (25 days + 15 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 04 61 46 00 00 00 a0 Device Fault; Error: ABRT | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| ef 03 46 00 00 00 a0 08 00:01:14.464 SET FEATURES [Set transfer mode] | |
| ef 10 02 00 00 00 a0 08 00:01:14.464 SET FEATURES [Enable SATA feature] | |
| ec 00 00 00 00 00 a0 08 00:01:14.463 IDENTIFY DEVICE | |
| ef 10 02 00 00 00 a0 08 00:01:14.455 SET FEATURES [Enable SATA feature] | |
| Error 126 occurred at disk power-on lifetime: 615 hours (25 days + 15 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 04 61 02 00 00 00 a0 Device Fault; Error: ABRT | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| ef 10 02 00 00 00 a0 08 00:01:14.464 SET FEATURES [Enable SATA feature] | |
| ec 00 00 00 00 00 a0 08 00:01:14.463 IDENTIFY DEVICE | |
| ef 10 02 00 00 00 a0 08 00:01:14.455 SET FEATURES [Enable SATA feature] | |
| ec 00 00 00 00 00 a0 08 00:01:14.455 IDENTIFY DEVICE | |
| Error 125 occurred at disk power-on lifetime: 615 hours (25 days + 15 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 04 61 02 00 00 00 a0 Device Fault; Error: ABRT | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| ef 10 02 00 00 00 a0 08 00:01:14.455 SET FEATURES [Enable SATA feature] | |
| ec 00 00 00 00 00 a0 08 00:01:14.455 IDENTIFY DEVICE | |
| ef 03 46 00 00 00 a0 08 00:01:14.455 SET FEATURES [Set transfer mode] | |
| ef 10 02 00 00 00 a0 08 00:01:14.455 SET FEATURES [Enable SATA feature] | |
| ec 00 00 00 00 00 a0 08 00:01:14.454 IDENTIFY DEVICE | |
| Error 124 occurred at disk power-on lifetime: 615 hours (25 days + 15 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 04 61 46 00 00 00 a0 Device Fault; Error: ABRT | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| ef 03 46 00 00 00 a0 08 00:01:14.455 SET FEATURES [Set transfer mode] | |
| ef 10 02 00 00 00 a0 08 00:01:14.455 SET FEATURES [Enable SATA feature] | |
| ec 00 00 00 00 00 a0 08 00:01:14.454 IDENTIFY DEVICE | |
| ef 10 02 00 00 00 a0 08 00:01:14.448 SET FEATURES [Enable SATA feature] | |
| SMART Self-test log structure revision number 1 | |
| Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error | |
| # 1 Extended offline Completed without error 00% 272 - | |
| # 2 Extended offline Completed: read failure 70% 231 2478939616 | |
| 1 of 1 failed self-tests are outdated by newer successful extended offline self-test # 1 | |
| SMART Selective self-test log data structure revision number 1 | |
| SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS | |
| 1 0 0 Not_testing | |
| 2 0 0 Not_testing | |
| 3 0 0 Not_testing | |
| 4 0 0 Not_testing | |
| 5 0 0 Not_testing | |
| Selective self-test flags (0x0): | |
| After scanning selected spans, do NOT read-scan remainder of disk. | |
| If Selective self-test is pending on power-up, resume after 0 minute delay. |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment