| smartctl -a /dev/sda | |
| smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-93-generic] (local build) | |
| Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org | |
| Smartctl open device: /dev/sda failed: Permission denied | |
| skinux@skibunix:~/Projects/entertainerlaravel$ sudo smartctl -a /dev/sda | |
| smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-93-generic] (local build) | |
| Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org | |
| === START OF INFORMATION SECTION === | |
| Model Family: Seagate Laptop Thin HDD | |
| Device Model: ST500LT012-9WS142 | |
| Serial Number: W0V48546 | |
| LU WWN Device Id: 5 000c50 05dbc6e01 | |
| Firmware Version: 0001SDM1 | |
| User Capacity: 500,107,862,016 bytes [500 GB] | |
| Sector Sizes: 512 bytes logical, 4096 bytes physical | |
| Rotation Rate: 5400 rpm | |
| Form Factor: 2.5 inches | |
| Device is: In smartctl database [for details use: -P show] | |
| ATA Version is: ATA8-ACS T13/1699-D revision 4 | |
| SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s) | |
| Local Time is: Sun Sep 17 05:04:06 2017 PDT | |
| SMART support is: Available - device has SMART capability. | |
| SMART support is: Enabled | |
| === START OF READ SMART DATA SECTION === | |
| SMART overall-health self-assessment test result: PASSED | |
| General SMART Values: | |
| Offline data collection status: (0x82) Offline data collection activity | |
| was completed without error. | |
| Auto Offline Data Collection: Enabled. | |
| Self-test execution status: ( 0) The previous self-test routine completed | |
| without error or no self-test has ever | |
| been run. | |
| Total time to complete Offline | |
| data collection: ( 0) seconds. | |
| Offline data collection | |
| capabilities: (0x7b) SMART execute Offline immediate. | |
| Auto Offline data collection on/off support. | |
| Suspend Offline collection upon new | |
| command. | |
| Offline surface scan supported. | |
| Self-test supported. | |
| Conveyance Self-test supported. | |
| Selective Self-test supported. | |
| SMART capabilities: (0x0003) Saves SMART data before entering | |
| power-saving mode. | |
| Supports SMART auto save timer. | |
| Error logging capability: (0x01) Error logging supported. | |
| General Purpose Logging supported. | |
| Short self-test routine | |
| recommended polling time: ( 1) minutes. | |
| Extended self-test routine | |
| recommended polling time: ( 106) minutes. | |
| Conveyance self-test routine | |
| recommended polling time: ( 2) minutes. | |
| SCT capabilities: (0x1035) SCT Status supported. | |
| SCT Feature Control supported. | |
| SCT Data Table supported. | |
| SMART Attributes Data Structure revision number: 10 | |
| Vendor Specific SMART Attributes with Thresholds: | |
| ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE | |
| 1 Raw_Read_Error_Rate 0x000f 119 073 006 Pre-fail Always - 205174312 | |
| 3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always - 0 | |
| 4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1670 | |
| 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 | |
| 7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 13752733939 | |
| 9 Power_On_Hours 0x0032 060 060 000 Old_age Always - 35114 (30 20 0) | |
| 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 | |
| 12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1503 | |
| 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 | |
| 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 17003 | |
| 188 Command_Timeout 0x0032 100 099 000 Old_age Always - 4295032838 | |
| 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 | |
| 190 Airflow_Temperature_Cel 0x0022 066 050 045 Old_age Always - 34 (Min/Max 32/35) | |
| 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 1736 | |
| 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 306 | |
| 193 Load_Cycle_Count 0x0032 027 027 000 Old_age Always - 147171 | |
| 194 Temperature_Celsius 0x0022 034 050 000 Old_age Always - 34 (0 9 0 0 0) | |
| 196 Reallocated_Event_Count 0x000f 061 061 030 Pre-fail Always - 34878 (10667 0) | |
| 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 | |
| 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 | |
| 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 | |
| 240 Head_Flying_Hours 0x0000 061 061 000 Old_age Offline - 34878 (41 171 0) | |
| 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 1061428046 | |
| 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 3642957928 | |
| 254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0 | |
| SMART Error Log Version: 1 | |
| ATA Error Count: 17003 (device log contains only the most recent five errors) | |
| CR = Command Register [HEX] | |
| FR = Features Register [HEX] | |
| SC = Sector Count Register [HEX] | |
| SN = Sector Number Register [HEX] | |
| CL = Cylinder Low Register [HEX] | |
| CH = Cylinder High Register [HEX] | |
| DH = Device/Head Register [HEX] | |
| DC = Device Command Register [HEX] | |
| ER = Error register [HEX] | |
| ST = Status register [HEX] | |
| Powered_Up_Time is measured from power on, and printed as | |
| DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, | |
| SS=sec, and sss=millisec. It "wraps" after 49.710 days. | |
| Error 17003 occurred at disk power-on lifetime: 33814 hours (1408 days + 22 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 40 51 00 ff ff ff 0f Error: WP at LBA = 0x0fffffff = 268435455 | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| 61 00 60 ff ff ff 4f 00 25d+18:42:14.966 WRITE FPDMA QUEUED | |
| 61 00 08 ff ff ff 4f 00 25d+18:42:14.966 WRITE FPDMA QUEUED | |
| 60 00 08 ff ff ff 4f 00 25d+18:42:14.966 READ FPDMA QUEUED | |
| 60 00 08 ff ff ff 4f 00 25d+18:42:14.966 READ FPDMA QUEUED | |
| 60 00 08 ff ff ff 4f 00 25d+18:42:14.966 READ FPDMA QUEUED | |
| Error 17002 occurred at disk power-on lifetime: 33814 hours (1408 days + 22 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| 60 00 08 ff ff ff 4f 00 25d+18:42:06.754 READ FPDMA QUEUED | |
| 60 00 08 ff ff ff 4f 00 25d+18:42:06.744 READ FPDMA QUEUED | |
| 60 00 08 ff ff ff 4f 00 25d+18:42:06.720 READ FPDMA QUEUED | |
| 60 00 08 ff ff ff 4f 00 25d+18:42:06.711 READ FPDMA QUEUED | |
| 60 00 08 ff ff ff 4f 00 25d+18:42:06.711 READ FPDMA QUEUED | |
| Error 17001 occurred at disk power-on lifetime: 23877 hours (994 days + 21 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 40 51 00 ff ff ff 0f Error: WP at LBA = 0x0fffffff = 268435455 | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| 61 00 10 ff ff ff 4f 00 13:07:51.002 WRITE FPDMA QUEUED | |
| 60 00 28 ff ff ff 4f 00 13:07:51.002 READ FPDMA QUEUED | |
| 61 00 08 ff ff ff 4f 00 13:07:51.002 WRITE FPDMA QUEUED | |
| 61 00 10 ff ff ff 4f 00 13:07:51.002 WRITE FPDMA QUEUED | |
| 61 00 18 ff ff ff 4f 00 13:07:51.002 WRITE FPDMA QUEUED | |
| Error 17000 occurred at disk power-on lifetime: 23877 hours (994 days + 21 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| 60 00 20 ff ff ff 4f 00 13:07:42.827 READ FPDMA QUEUED | |
| 60 00 30 ff ff ff 4f 00 13:07:42.815 READ FPDMA QUEUED | |
| 60 00 20 ff ff ff 4f 00 13:07:42.815 READ FPDMA QUEUED | |
| 60 00 18 ff ff ff 4f 00 13:07:42.812 READ FPDMA QUEUED | |
| ea 00 00 00 00 00 a0 00 13:07:42.801 FLUSH CACHE EXT | |
| Error 16999 occurred at disk power-on lifetime: 23515 hours (979 days + 19 hours) | |
| When the command that caused the error occurred, the device was active or idle. | |
| After command completion occurred, registers were: | |
| ER ST SC SN CL CH DH | |
| -- -- -- -- -- -- -- | |
| 40 51 00 e0 f0 d1 01 Error: WP at LBA = 0x01d1f0e0 = 30535904 | |
| Commands leading to the command that caused the error were: | |
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
| -- -- -- -- -- -- -- -- ---------------- -------------------- | |
| 61 00 00 f0 48 91 4e 00 02:40:14.715 WRITE FPDMA QUEUED | |
| 61 00 00 f0 47 91 4e 00 02:40:14.715 WRITE FPDMA QUEUED | |
| 61 00 00 f0 46 91 4e 00 02:40:14.715 WRITE FPDMA QUEUED | |
| 61 00 00 f0 45 91 4e 00 02:40:14.715 WRITE FPDMA QUEUED | |
| 61 00 00 f0 44 91 4e 00 02:40:14.715 WRITE FPDMA QUEUED | |
| SMART Self-test log structure revision number 1 | |
| Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error | |
| # 1 Short offline Completed without error 00% 23704 - | |
| # 2 Offline Aborted by host 90% 23703 - | |
| # 3 Short offline Completed without error 00% 23452 - | |
| # 4 Offline Aborted by host 90% 23452 - | |
| # 5 Short offline Completed without error 00% 23370 - | |
| # 6 Offline Aborted by host 90% 23370 - | |
| # 7 Offline Aborted by host 90% 22984 - | |
| # 8 Offline Aborted by host 90% 22890 - | |
| # 9 Short offline Completed: read failure 90% 22753 210345360 | |
| #10 Offline Aborted by host 90% 22752 - | |
| #11 Offline Aborted by host 90% 22684 - | |
| #12 Offline Aborted by host 90% 22465 - | |
| #13 Short offline Aborted by host 90% 20737 - | |
| #14 Short offline Aborted by host 90% 19993 - | |
| #15 Short offline Aborted by host 90% 18075 - | |
| #16 Short offline Completed without error 00% 9597 - | |
| #17 Short offline Completed without error 00% 7256 - | |
| #18 Offline Aborted by host 90% 7256 - | |
| #19 Short offline Completed without error 00% 3102 - | |
| #20 Short offline Completed without error 00% 1770 - | |
| #21 Short offline Completed without error 00% 491 - | |
| SMART Selective self-test log data structure revision number 1 | |
| SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS | |
| 1 0 0 Not_testing | |
| 2 0 0 Not_testing | |
| 3 0 0 Not_testing | |
| 4 0 0 Not_testing | |
| 5 0 0 Not_testing | |
| Selective self-test flags (0x0): | |
| After scanning selected spans, do NOT read-scan remainder of disk. | |
| If Selective self-test is pending on power-up, resume after 0 minute delay. |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment