Raspberry Pi wifi adapter dmesg output
Linux version 3.1.9+ (dc4@dc4-arm-01) (gcc version 4.5.1 (Broadcom-2708) ) #52 Tue May 8 23:49:32 BST 2012 | |
CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d | |
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache | |
Machine: BCM2708 | |
Memory policy: ECC disabled, Data cache writeback | |
On node 0 totalpages: 57344 | |
free_area_init_node: node 0, pgdat c03bb910, node_mem_map c0408000 | |
Normal zone: 448 pages used for memmap | |
Normal zone: 0 pages reserved | |
Normal zone: 56896 pages, LIFO batch:15 | |
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 | |
pcpu-alloc: [0] 0 | |
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 56896 | |
Kernel command line: dma.dmachans=0x3c bcm2708_fb.fbwidth=1504 bcm2708_fb.fbheight=1104 bcm2708.boardrev=0x2 bcm2708.serial=0x3660bc2 smsc95xx.macaddr=B8:27:EB:66:0B:C2 dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait | |
PID hash table entries: 1024 (order: 0, 4096 bytes) | |
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) | |
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) | |
Memory: 224MB = 224MB total | |
Memory: 223208k/223208k available, 6168k reserved, 0K highmem | |
Virtual kernel memory layout: | |
vector : 0xffff0000 - 0xffff1000 ( 4 kB) | |
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) | |
DMA : 0xffc00000 - 0xffe00000 ( 2 MB) | |
vmalloc : 0xce800000 - 0xd8000000 ( 152 MB) | |
lowmem : 0xc0000000 - 0xce000000 ( 224 MB) | |
modules : 0xbf000000 - 0xc0000000 ( 16 MB) | |
.text : 0xc0008000 - 0xc0381000 (3556 kB) | |
.init : 0xc0381000 - 0xc039e000 ( 116 kB) | |
.data : 0xc039e000 - 0xc03bbfa0 ( 120 kB) | |
.bss : 0xc03bbfc4 - 0xc0407478 ( 302 kB) | |
NR_IRQS:85 | |
timer_set_mode: unhandled mode:1 | |
timer_set_mode: unhandled mode:3 | |
Console: colour dummy device 80x30 | |
console [tty1] enabled | |
Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216) | |
pid_max: default: 32768 minimum: 301 | |
Mount-cache hash table entries: 512 | |
CPU: Testing write buffer coherency: ok | |
devtmpfs: initialized | |
NET: Registered protocol family 16 | |
vc-mem: mm_vc_mem_phys_addr = 0x00000000 | |
vc-mem: mm_vc_mem_size = 0x10000000 (256 MiB) | |
mailbox: Broadcom VideoCore Mailbox driver | |
bcm2708_vcio: mailbox at f200b880 | |
bcm_power: Broadcom power driver | |
bcm_power_open() -> 0 | |
bcm_power_request(0, 8) | |
bcm_mailbox_read -> 00000080, 0 | |
bcm_power_request -> 0 | |
Serial: AMBA PL011 UART driver | |
dev:f1: ttyAMA0 at MMIO 0x20201000 (irq = 83) is a PL011 rev3 | |
console [ttyAMA0] enabled | |
bio: create slab <bio-0> at 0 | |
SCSI subsystem initialized | |
usbcore: registered new interface driver usbfs | |
usbcore: registered new interface driver hub | |
usbcore: registered new device driver usb | |
Switching to clocksource stc | |
FS-Cache: Loaded | |
CacheFiles: Loaded | |
Switched to NOHz mode on CPU #0 | |
NET: Registered protocol family 2 | |
IP route cache hash table entries: 2048 (order: 1, 8192 bytes) | |
TCP established hash table entries: 8192 (order: 4, 65536 bytes) | |
TCP bind hash table entries: 8192 (order: 3, 32768 bytes) | |
TCP: Hash tables configured (established 8192 bind 8192) | |
TCP reno registered | |
UDP hash table entries: 256 (order: 0, 4096 bytes) | |
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) | |
NET: Registered protocol family 1 | |
RPC: Registered named UNIX socket transport module. | |
RPC: Registered udp transport module. | |
RPC: Registered tcp transport module. | |
RPC: Registered tcp NFSv4.1 backchannel transport module. | |
bcm2708_dma: DMA manager at ce808000 | |
bcm2708_gpio: bcm2708_gpio_probe c03a3d88 | |
vc-mem: Videocore memory driver | |
VFS: Disk quotas dquot_6.5.2 | |
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) | |
FS-Cache: Netfs 'nfs' registered for caching | |
msgmni has been set to 435 | |
io scheduler noop registered | |
io scheduler deadline registered | |
io scheduler cfq registered (default) | |
BCM2708FB: registering framebuffer (1504x1104@16) | |
bcm2708_fb_set_par info(cd888000) 1504x1104 (1504x1104), 0, 16 | |
BCM2708FB: start = cec00000,4f385000 width=1504, height=1104, bpp=16, pitch=3008 size=3321856 success=0 | |
Console: switching to colour frame buffer device 188x69 | |
BCM2708FB: register framebuffer (0) | |
brd: module loaded | |
loop: module loaded | |
vcos: [1]: vchiq_init_state: slot_zero = 0xffd80000, is_master = 0 | |
vcos: [1]: vchiq_init_state: called | |
vcos: [1]: vchiq: initialised - version 2 (min 2), device 253.0 | |
usbcore: registered new interface driver smsc95xx | |
cdc_ncm: 04-Aug-2011 | |
usbcore: registered new interface driver cdc_ncm | |
dwc_otg: version 2.90b 6-MAY-2010 (platform bus) | |
Core Release: 2.80a | |
Setting default values for core params | |
Finished setting default values for core params | |
ce840008 -> 1 | |
Using Buffer DMA mode | |
Periodic Transfer Interrupt Enhancement - disabled | |
Multiprocessor Interrupt Enhancement - disabled | |
Dedicated Tx FIFOs mode | |
dwc_otg bcm2708_usb: DWC OTG Controller | |
dwc_otg bcm2708_usb: new USB bus registered, assigned bus number 1 | |
dwc_otg bcm2708_usb: irq 75, io mem 0x00000000 | |
Init: Port Power? op_state=1 | |
Init: Power Port (0) | |
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 | |
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 | |
usb usb1: Product: DWC OTG Controller | |
usb usb1: Manufacturer: Linux 3.1.9+ dwc_otg_hcd | |
usb usb1: SerialNumber: bcm2708_usb | |
hub 1-0:1.0: USB hub found | |
hub 1-0:1.0: 1 port detected | |
Module dwc_common_port init | |
usbcore: registered new interface driver uas | |
Initializing USB Mass Storage driver... | |
usbcore: registered new interface driver usb-storage | |
USB Mass Storage support registered. | |
usbcore: registered new interface driver libusual | |
mousedev: PS/2 mouse device common for all mice | |
cpuidle: using governor ladder | |
cpuidle: using governor menu | |
sdhci: Secure Digital Host Controller Interface driver | |
sdhci: Copyright(c) Pierre Ossman | |
bcm_power_open() -> 1 | |
Registered led device: mmc0:: | |
mmc0: SDHCI controller on BCM2708_Arasan [platform] using platform's DMA | |
mmc0: BCM2708 SDHC host at 0x20300000 DMA 2 IRQ 77 | |
sdhci-pltfm: SDHCI platform and OF driver helper | |
Registered led device: led0 | |
usbcore: registered new interface driver usbhid | |
usbhid: USB HID core driver | |
TCP cubic registered | |
Initializing XFRM netlink socket | |
NET: Registered protocol family 17 | |
Registering the dns_resolver key type | |
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5 | |
Waiting for root device /dev/mmcblk0p2... | |
mmc0: new SD card at address 0002 | |
mmcblk0: mmc0:0002 00000 1.86 GiB | |
mmcblk0: p1 p2 p3 | |
usb 1-1: new high speed USB device number 2 using dwc_otg | |
usb 1-1: New USB device found, idVendor=0424, idProduct=9512 | |
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 | |
hub 1-1:1.0: USB hub found | |
hub 1-1:1.0: 3 ports detected | |
usb 1-1.1: new high speed USB device number 3 using dwc_otg | |
usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00 | |
usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 | |
smsc95xx v1.0.4 | |
smsc95xx 1-1.1:1.0: eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:66:0b:c2 | |
usb 1-1.2: new low speed USB device number 4 using dwc_otg | |
usb 1-1.2: New USB device found, idVendor=045e, idProduct=00b4 | |
usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 | |
usb 1-1.2: Product: Microsoft\xffffffc2\xffffffae\xffffffae Digital Media Keyboard | |
usb 1-1.2: Manufacturer: Microsoft | |
input: Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Digital Media Keyboard as /devices/platform/bcm2708_usb/usb1/1-1/1-1.2/1-1.2:1.0/input/input0 | |
generic-usb 0003:045E:00B4.0001: input: USB HID v1.11 Keyboard [Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Digital Media Keyboard] on usb-bcm2708_usb-1.2/input0 | |
input: Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Digital Media Keyboard as /devices/platform/bcm2708_usb/usb1/1-1/1-1.2/1-1.2:1.1/input/input1 | |
generic-usb 0003:045E:00B4.0002: input: USB HID v1.11 Device [Microsoft Microsoft\xffffffc2\xffffffae\xffffffae Digital Media Keyboard] on usb-bcm2708_usb-1.2/input1 | |
EXT4-fs (mmcblk0p2): recovery complete | |
EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) | |
VFS: Mounted root (ext4 filesystem) on device 179:2. | |
Freeing init memory: 116K | |
EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) | |
smsc95xx 1-1.1:1.0: eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1 | |
usb 1-1.3: new high speed USB device number 5 using dwc_otg | |
usb 1-1.3: New USB device found, idVendor=7392, idProduct=7811 | |
usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 | |
usb 1-1.3: Product: 802.11n WLAN Adapter | |
usb 1-1.3: Manufacturer: Realtek | |
usb 1-1.3: SerialNumber: 00e04c000001 | |
rtw driver version=v3.0.2164.20110715 | |
register rtw_netdev_ops to netdev_ops | |
CHIP TYPE: RTL8188C_8192C | |
usb_endpoint_descriptor(0): | |
bLength=7 | |
bDescriptorType=5 | |
bEndpointAddress=81 | |
wMaxPacketSize=200 | |
bInterval=0 | |
RT_usb_endpoint_is_bulk_in = 1 | |
usb_endpoint_descriptor(1): | |
bLength=7 | |
bDescriptorType=5 | |
bEndpointAddress=2 | |
wMaxPacketSize=200 | |
bInterval=0 | |
RT_usb_endpoint_is_bulk_out = 2 | |
usb_endpoint_descriptor(2): | |
bLength=7 | |
bDescriptorType=5 | |
bEndpointAddress=3 | |
wMaxPacketSize=200 | |
bInterval=0 | |
RT_usb_endpoint_is_bulk_out = 3 | |
usb_endpoint_descriptor(3): | |
bLength=7 | |
bDescriptorType=5 | |
bEndpointAddress=84 | |
wMaxPacketSize=40 | |
bInterval=1 | |
RT_usb_endpoint_is_int_in = 4, Interval = 1 | |
nr_endpoint=4, in_num=2, out_num=2 | |
USB_SPEED_HIGH | |
Chip Version ID: VERSION_NORMAL_TSMC_CHIP_88C. | |
RF_Type is 3!! | |
EEPROM type is E-FUSE | |
====> ReadAdapterInfo8192C | |
Boot from EFUSE, Autoload OK ! | |
EEPROMVID = 0x7392 | |
EEPROMPID = 0x7811 | |
EEPROMCustomerID : 0x00 | |
EEPROMSubCustomerID: 0x00 | |
RT_CustomerID: 0x00 | |
_ReadMACAddress MAC Address from EFUSE = 80:1f:02:5c:46:51 | |
EEPROMRegulatory = 0x0 | |
_ReadBoardType(0) | |
BT Coexistance = disable | |
RT_ChannelPlan: 0x00 | |
_ReadPSSetting...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(0) | |
### PS params=> power_mgnt(0),usbss_enable(0) ### | |
### AntDivCfg(0) | |
readAdapterInfo_8192CU(): REPLACEMENT = 1 | |
<==== ReadAdapterInfo8192C in 270 ms | |
rtw_macaddr_cfg MAC Address = 80:1f:02:5c:46:51 | |
MAC Address from pnetdev->dev_addr= 80:1f:02:5c:46:51 | |
bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0 | |
usbcore: registered new interface driver rtl8192cu | |
+871x_drv - drv_open, bup=0 | |
===> FirmwareDownload91C() fw:Rtl819XFwImageArray_TSMC | |
fw_ver=v75, fw_subver=0, sig=0x88c0 | |
fw download ok! | |
Set RF Chip ID to RF_6052 and RF type to 1T1R. | |
GPIO_IN=0c | |
eRfPowerStateToSet=0 | |
IQK:Start!!! | |
Path A IQK Success!! | |
Path A IQK Success!! | |
IQK: final_candidate is 0 | |
IQK: RegE94=103 RegE9C=13 RegEA4=ff RegEAC=3ff RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0 | |
Path A IQ Calibration Success ! | |
pdmpriv->TxPowerTrackControl = 1 | |
MAC Address from REG_MACID = 80:1f:02:5c:46:51 | |
MAC Address = 80:1f:02:5c:46:51 | |
-871x_drv - drv_open, bup=1 | |
[rtw_wx_set_pmkid] IW_PMKSA_FLUSH! | |
set_mode = IW_MODE_INFRA | |
=>rtw_wx_set_essid | |
ssid=g\xffffffc6isQ\xffffffffJ\xffffffec)\xffffffcd\xffffffba\xffffffba\xffffffab\xfffffff2\xfffffffb\xffffffe3F|\xffffffc2T\xfffffff8\x1b\xffffffe8\xffffffe7\xffffff8dvZ.c3\xffffff9f\xffffffc9\xffffff9a\xffffff9a\xffffff80\xfffffff4\xffffffb8\xffffffcd\xffffff80\xffffff80\xfffffff4\xffffffb8\xffffffcd, len=32 | |
[rtw_wx_set_pmkid] IW_PMKSA_FLUSH! | |
###=> usb_read_port_complete => urb status(-71) | |
###=> usb_read_port_complete => urb status(-71) | |
###=> usb_read_port_complete => urb status(-71) | |
###=> usb_read_port_complete => urb status(-71) | |
###=> usb_read_port_complete => urb status(-71) | |
continual_urb_error > 4 | |
###=> usb_read_port_complete => urb status(-71) | |
continual_urb_error > 4 | |
###=> usb_read_port_complete => urb status(-71) | |
continual_urb_error > 4 | |
###=> usb_read_port_complete => urb status(-71) | |
continual_urb_error > 4 | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
reg 0xe08, usb read fail ,status:-71 value=0x0 | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
usb 1-1.3: USB disconnect, device number 5 | |
+rtw_dev_remove | |
(2)871x_drv - drv_close, bup=1, hw_init_completed=1 | |
-871x_drv - drv_close, bup=1 | |
reg 0xe08, usb write fail ,status:-71 value=0x2900 | |
###> rtw_cmd_thread break................. | |
reg 0x4c, usb read fail ,status:-19 value=0x0 | |
===> rtw_dev_unload | |
usb_read_port_cancel | |
usb_write_port_cancel | |
<=== rtw_dev_unload | |
+r871xu_dev_remove, hw_init_completed=1 | |
free_recv_skb_queue not empty, 4 | |
=====> rtl8192c_free_hal_data ===== | |
<===== rtl8192c_free_hal_data ===== | |
-r871xu_dev_remove, done | |
usb 1-1.3: new high speed USB device number 6 using dwc_otg | |
usb 1-1.3: New USB device found, idVendor=7392, idProduct=7811 | |
usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 | |
usb 1-1.3: Product: 802.11n WLAN Adapter | |
usb 1-1.3: Manufacturer: Realtek | |
usb 1-1.3: SerialNumber: 00e04c000001 | |
register rtw_netdev_ops to netdev_ops | |
CHIP TYPE: RTL8188C_8192C | |
usb_endpoint_descriptor(0): | |
bLength=7 | |
bDescriptorType=5 | |
bEndpointAddress=81 | |
wMaxPacketSize=200 | |
bInterval=0 | |
RT_usb_endpoint_is_bulk_in = 1 | |
usb_endpoint_descriptor(1): | |
bLength=7 | |
bDescriptorType=5 | |
bEndpointAddress=2 | |
wMaxPacketSize=200 | |
bInterval=0 | |
RT_usb_endpoint_is_bulk_out = 2 | |
usb_endpoint_descriptor(2): | |
bLength=7 | |
bDescriptorType=5 | |
bEndpointAddress=3 | |
wMaxPacketSize=200 | |
bInterval=0 | |
RT_usb_endpoint_is_bulk_out = 3 | |
usb_endpoint_descriptor(3): | |
bLength=7 | |
bDescriptorType=5 | |
bEndpointAddress=84 | |
wMaxPacketSize=40 | |
bInterval=1 | |
RT_usb_endpoint_is_int_in = 4, Interval = 1 | |
nr_endpoint=4, in_num=2, out_num=2 | |
USB_SPEED_HIGH | |
Chip Version ID: VERSION_NORMAL_TSMC_CHIP_88C. | |
RF_Type is 3!! | |
EEPROM type is E-FUSE | |
====> ReadAdapterInfo8192C | |
Boot from EFUSE, Autoload OK ! | |
EEPROMVID = 0x7392 | |
EEPROMPID = 0x7811 | |
EEPROMCustomerID : 0x00 | |
EEPROMSubCustomerID: 0x00 | |
RT_CustomerID: 0x00 | |
_ReadMACAddress MAC Address from EFUSE = 80:1f:02:5c:46:51 | |
EEPROMRegulatory = 0x0 | |
_ReadBoardType(0) | |
BT Coexistance = disable | |
RT_ChannelPlan: 0x00 | |
_ReadPSSetting...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(0) | |
### PS params=> power_mgnt(0),usbss_enable(0) ### | |
### AntDivCfg(0) | |
readAdapterInfo_8192CU(): REPLACEMENT = 1 | |
<==== ReadAdapterInfo8192C in 300 ms | |
rtw_macaddr_cfg MAC Address = 80:1f:02:5c:46:51 | |
MAC Address from pnetdev->dev_addr= 80:1f:02:5c:46:51 | |
bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0 | |
+871x_drv - drv_open, bup=0 | |
===> FirmwareDownload91C() fw:Rtl819XFwImageArray_TSMC | |
fw_ver=v75, fw_subver=0, sig=0x88c0 | |
fw download ok! | |
Set RF Chip ID to RF_6052 and RF type to 1T1R. | |
GPIO_IN=0c | |
eRfPowerStateToSet=0 | |
IQK:Start!!! | |
Path A IQK Success!! | |
Path A IQK Success!! | |
IQK: final_candidate is 0 | |
IQK: RegE94=104 RegE9C=13 RegEA4=ff RegEAC=3ff RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0 | |
Path A IQ Calibration Success ! | |
pdmpriv->TxPowerTrackControl = 1 | |
MAC Address from REG_MACID = 80:1f:02:5c:46:51 | |
MAC Address = 80:1f:02:5c:46:51 | |
-871x_drv - drv_open fail, bup=0 | |
+871x_drv - drv_open, bup=0 | |
===> FirmwareDownload91C() fw:Rtl819XFwImageArray_TSMC | |
fw_ver=v75, fw_subver=0, sig=0x88c0 | |
rtl8192c_FirmwareSelfReset =====> 8051 reset success (100) . | |
reg 0x80, usb read fail ,status:-110 value=0x0 | |
fw download ok! | |
Set RF Chip ID to RF_6052 and RF type to 1T1R. | |
GPIO_IN=0c | |
eRfPowerStateToSet=0 | |
pdmpriv->TxPowerTrackControl = 1 | |
MAC Address from REG_MACID = 80:1f:02:5c:46:51 | |
MAC Address = 80:1f:02:5c:46:51 | |
-871x_drv - drv_open, bup=1 | |
[rtw_wx_set_pmkid] IW_PMKSA_FLUSH! | |
set_mode = IW_MODE_INFRA | |
=>rtw_wx_set_essid | |
ssid=g\xffffffc6isQ\xffffffffJ\xffffffec)\xffffffcd\xffffffba\xffffffba\xffffffab\xfffffff2\xfffffffb\xffffffe3F|\xffffffc2T\xfffffff8\x1b\xffffffe8\xffffffe7\xffffff8dvZ.c3\xffffff9f\xffffffc9\xffffff9a\xffffff9a, len=32 | |
[rtw_wx_set_pmkid] IW_PMKSA_FLUSH! | |
###=> usb_read_port_complete => urb status(-71) | |
###=> usb_read_port_complete => urb status(-71) | |
###=> usb_read_port_complete => urb status(-71) | |
###=> usb_read_port_complete => urb status(-71) | |
###=> usb_read_port_complete => urb status(-71) | |
continual_urb_error > 4 | |
###=> usb_read_port_complete => urb status(-71) | |
continual_urb_error > 4 | |
###=> usb_read_port_complete => urb status(-71) | |
continual_urb_error > 4 | |
###=> usb_read_port_complete => urb status(-71) | |
continual_urb_error > 4 | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
reg 0xe08, usb read fail ,status:-71 value=0x0 | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
reg 0xe08, usb write fail ,status:-71 value=0x2900 | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
reg 0x86c, usb read fail ,status:-71 value=0x0 | |
usb 1-1.3: USB disconnect, device number 6 | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
+rtw_dev_remove | |
(2)871x_drv - drv_close, bup=1, hw_init_completed=1 | |
-871x_drv - drv_close, bup=1 | |
reg 0x86c, usb write fail ,status:-71 value=0x29292900 | |
###> rtw_cmd_thread break................. | |
reg 0x4c, usb read fail ,status:-19 value=0x0 | |
===> rtw_dev_unload | |
usb_read_port_cancel | |
usb_write_port_cancel | |
<=== rtw_dev_unload | |
+r871xu_dev_remove, hw_init_completed=1 | |
free_recv_skb_queue not empty, 4 | |
=====> rtl8192c_free_hal_data ===== | |
<===== rtl8192c_free_hal_data ===== | |
-r871xu_dev_remove, done | |
usb 1-1.3: new high speed USB device number 8 using dwc_otg | |
usb 1-1.3: New USB device found, idVendor=7392, idProduct=7811 | |
usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 | |
usb 1-1.3: Product: 802.11n WLAN Adapter | |
usb 1-1.3: Manufacturer: Realtek | |
usb 1-1.3: SerialNumber: 00e04c000001 | |
register rtw_netdev_ops to netdev_ops | |
CHIP TYPE: RTL8188C_8192C | |
usb_endpoint_descriptor(0): | |
bLength=7 | |
bDescriptorType=5 | |
bEndpointAddress=81 | |
wMaxPacketSize=200 | |
bInterval=0 | |
RT_usb_endpoint_is_bulk_in = 1 | |
usb_endpoint_descriptor(1): | |
bLength=7 | |
bDescriptorType=5 | |
bEndpointAddress=2 | |
wMaxPacketSize=200 | |
bInterval=0 | |
RT_usb_endpoint_is_bulk_out = 2 | |
usb_endpoint_descriptor(2): | |
bLength=7 | |
bDescriptorType=5 | |
bEndpointAddress=3 | |
wMaxPacketSize=200 | |
bInterval=0 | |
RT_usb_endpoint_is_bulk_out = 3 | |
usb_endpoint_descriptor(3): | |
bLength=7 | |
bDescriptorType=5 | |
bEndpointAddress=84 | |
wMaxPacketSize=40 | |
bInterval=1 | |
RT_usb_endpoint_is_int_in = 4, Interval = 1 | |
nr_endpoint=4, in_num=2, out_num=2 | |
USB_SPEED_HIGH | |
Chip Version ID: VERSION_NORMAL_TSMC_CHIP_88C. | |
RF_Type is 3!! | |
EEPROM type is E-FUSE | |
====> ReadAdapterInfo8192C | |
Boot from EFUSE, Autoload OK ! | |
EEPROMVID = 0x7392 | |
EEPROMPID = 0x7811 | |
EEPROMCustomerID : 0x00 | |
EEPROMSubCustomerID: 0x00 | |
RT_CustomerID: 0x00 | |
_ReadMACAddress MAC Address from EFUSE = 80:1f:02:5c:46:51 | |
EEPROMRegulatory = 0x0 | |
_ReadBoardType(0) | |
BT Coexistance = disable | |
RT_ChannelPlan: 0x00 | |
_ReadPSSetting...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(0) | |
### PS params=> power_mgnt(0),usbss_enable(0) ### | |
### AntDivCfg(0) | |
readAdapterInfo_8192CU(): REPLACEMENT = 1 | |
<==== ReadAdapterInfo8192C in 310 ms | |
rtw_macaddr_cfg MAC Address = 80:1f:02:5c:46:51 | |
MAC Address from pnetdev->dev_addr= 80:1f:02:5c:46:51 | |
bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0 | |
+871x_drv - drv_open, bup=0 | |
===> FirmwareDownload91C() fw:Rtl819XFwImageArray_TSMC | |
fw_ver=v75, fw_subver=0, sig=0x88c0 | |
fw download ok! | |
Set RF Chip ID to RF_6052 and RF type to 1T1R. | |
GPIO_IN=0c | |
eRfPowerStateToSet=0 | |
IQK:Start!!! | |
Path A IQK Success!! | |
Path A IQK Success!! | |
IQK: final_candidate is 0 | |
IQK: RegE94=104 RegE9C=13 RegEA4=fe RegEAC=3fe RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0 | |
Path A IQ Calibration Success ! | |
pdmpriv->TxPowerTrackControl = 1 | |
MAC Address from REG_MACID = 80:1f:02:5c:46:51 | |
MAC Address = 80:1f:02:5c:46:51 | |
-871x_drv - drv_open fail, bup=0 | |
+871x_drv - drv_open, bup=0 | |
===> FirmwareDownload91C() fw:Rtl819XFwImageArray_TSMC | |
fw_ver=v75, fw_subver=0, sig=0x88c0 | |
rtl8192c_FirmwareSelfReset =====> 8051 reset success (100) . | |
reg 0x80, usb read fail ,status:-71 value=0x0 | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
reg 0x80, usb write fail ,status:-71 value=0x1 | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
reg 0x82, usb read fail ,status:-71 value=0x0 | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
reg 0x82, usb write fail ,status:-71 value=0x0 | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
reg 0x82, usb read fail ,status:-71 value=0x0 | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
reg 0x82, usb write fail ,status:-71 value=0x0 | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
reg 0x1000, usb write fail ,status:-71 value=0xad4302 | |
usb 1-1.3: USB disconnect, device number 8 | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
DEBUG:handle_hc_chhltd_intr_dma:: XactErr without NYET/NAK/ACK | |
+rtw_dev_remove | |
reg 0x10c4, usb write fail ,status:-71 value=0x30001010 | |
chksum report faill ! REG_MCUFWDL:0x00000000 . | |
DL Firmware failed! | |
fw download fail! | |
-871x_drv - drv_open fail, bup=0 | |
<=== rtw_dev_unload | |
+r871xu_dev_remove, hw_init_completed=0 | |
free_recv_skb_queue not empty, 8 | |
=====> rtl8192c_free_hal_data ===== | |
<===== rtl8192c_free_hal_data ===== | |
-r871xu_dev_remove, done |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
This comment has been minimized.
I have the same problem, my wifi if rtl8723a,Could not connect with the AP.