q8h-v5-boot-uart.log

HELLO! BOOT0 is starting!
boot0 version : 3.0.0
reg_addr 0x01f00100 =0x00000000
reg_addr 0x01f00104 =0x00000000
reg_addr 0x01f00108 =0x00000000
reg_addr 0x01f0010c =0x00000000
reg_addr 0x01f00110 =0x00000000
reg_addr 0x01f00114 =0x00000000
[DRAM]ver 0.8 clk = 480
dram ok
dram size =512
sum=0xf0f07415
src_sum=0xf0f07415
Ready to disable icache.
Jump to secend Boot.
[      0.136]

U-Boot 2011.09-rc1-dirty (Dec 28 2013 - 09:46:56) Allwinner Technology

[      0.144]version: 1.1.0
[      0.157]pmbus:   ready
[      0.159]PMU: AXP221
[      0.162]PMU: AXP22x found
[      0.164]PMU: bat ratio = 73
[      0.167]PMU: dcdc3 1260
[      0.170]PMU: pll1 1008 Mhz
set power on vol to default
dcdc1_vol = 3000
dcdc2_vol = 1100
dcdc3_vol = 1260
dcdc4_vol = 0
dcdc5_vol = 1500
aldo2_vol = 2500
aldo3_vol = 3000
find power_sply to end
only battery exist, limit to dc
fel key old mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
[      0.215]DRAM:  512 MiB
relocation Offset is: 14b1b000
DRV_DISP_Init: opened
[      0.372]fetch script data boot_disp.output_type fail
[      0.378]fetch script data boot_disp.output_mode fail
[      0.383]fetch script data boot_disp.auto_hpd fail
[      0.388]lcd0_para.lcd_used=1
workmode = 0
[      0.403]NAND: NAND_UbootInit
NB1 : enter NAND_LogicInit
not burn nand partition table!
NB1 : nftl num: 2
 init nftl: 0
NB1 : NAND_LogicInit ok, result = 0x0
[      1.249]sunxi flash init ok
In:    serial
Out:   serial
Err:   serial
--------fastboot partitions--------
-total partitions:10-
-name-        -start-       -size-
boot-resource: 1000000       2000000
env         : 3000000       1000000
boot        : 4000000       1000000
system      : 5000000       30000000
data        : 35000000      20000000
misc        : 55000000      1000000
recovery    : 56000000      2000000
cache       : 58000000      20000000
databk      : 78000000      8000000
UDISK       : 80000000      0
-----------------------------------
check user_data_burn: run setargs_nand boot_normal
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_nand
key 0
recovery key high 12, low 4
cant find fstbt value
to be run cmd=run setargs_nand boot_normal
cant open script.bin, maybe it is not exist
WORK_MODE_BOOT
board_status_probe
[      1.343]pre sys mode
sunxi_bmp_display
[      1.349]Hit any key to stop autoboot:  0
read boot or recovery all
[      1.699]sunxi flash read :offset 4000000, 9876896 bytes OK
no signature
[      1.708]ready to boot
NAND_UbootExit
NB1 : NAND_LogicExit
[      1.710]
Starting kernel ...