Planex_MZK-W300NAG

gistfile1.txt

Starting kernel ...

FDT DTB  at: 0x882d5950
CPU   clock:  266MHz
Timer clock:  133MHz
UART  clock:  133MHz

U-Boot args (from 0 args):
        None
Environment:
entry: mips_init()
RAM size: 16MB (from FDT)
Cache info:
  picache_stride    = 4096
  picache_loopcount = 4
  pdcache_stride    = 4096
  pdcache_loopcount = 4
  max line size     = 16
cpu0: MIPS Technologies processor v108.144
  MMU: Standard TLB, 16 entries (4K 16K 64K 256K 1M 16M 64M 256M pg sizes)
  L1 i-cache: 4 ways of 256 sets, 16 bytes per line
  L1 d-cache: 4 ways of 256 sets, 16 bytes per line
  L2 cache: disabled
  Config1=0x9e9b4d86<MIPS16,EJTAG>
  Config2=0x80000000
  Config3=0x20
Physical memory chunk(s):
0x8336000 - 0x8ffffff, 13410304 bytes (3274 pages)
Maxmem is 0x9000000
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2017 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 12.0-CURRENT #6 7fbf228(zrouter)-dirty: Mon Oct 30 17:15:12 JST 2017
    hiroki@microserver:/storage/home/hiroki/zorg/obj/storage/home/hiroki/zorg/ZR
outer/tmp/mips.mipsel/storage/home/hiroki/freebsd/sys/Planex_MZK-W300NAG mips
gcc version 4.2.1 20070831 patched [FreeBSD]
Preloaded elf kernel "kernel" at 0x88329d90.
real memory  = 16777216 (16384K bytes)
Physical memory chunk(s):
0x083c2000 - 0x08f88fff, 12349440 bytes (3015 pages)
avail memory = 12054528 (11MB)
arc4random: no preloaded entropy cache
ULE: setup cpu 0
random: entropy device external interface
null: <full device, null device, zero device>
openfirm: <Open Firmware control device>
mem: <memory>
nexus0: <MIPS32 root nexus>
random: harvesting attach, 8 bytes (4 bits) from nexus0
ofwbus0: <Open Firmware Device Tree> on nexus0
palmbus0: <MTK Palmbus> mem 0x300000-0x4fffff on ofwbus0
random: harvesting attach, 8 bytes (4 bits) from palmbus0
random: harvesting attach, 8 bytes (4 bits) from ofwbus0
cpupic0: <MIPS32 Interrupt Controller> on ofwbus0
random: harvesting attach, 8 bytes (4 bits) from cpupic0
sysc0: <MTK System Controller> mem 0-0xff on palmbus0
random: harvesting attach, 8 bytes (4 bits) from sysc0
pinctrl0: <MTK Pin Controller> on ofwbus0
pinctrl0: GPIO mode start: 0x00000026
Processing 1 pin-config node(s) in pinctrl-0 for i2c@900
Processing 1 pin-config node(s) in pinctrl-0 for pinctrl
pinctrl0: GPIO mode end  : 0x00000026
random: harvesting attach, 8 bytes (4 bits) from pinctrl0
rstctrl0: <MTK Reset Controller> on ofwbus0
random: harvesting attach, 8 bytes (4 bits) from rstctrl0
clkctrl0: <MTK Clock Controller> on ofwbus0
random: harvesting attach, 8 bytes (4 bits) from clkctrl0
intc0: <MTK Interrupt Controller (v2)> mem 0x200-0x2ff irq 3 on palmbus0
random: harvesting attach, 8 bytes (4 bits) from intc0
gpio0: <MTK GPIO Controller (v1)> mem 0x600-0x633 irq 4 on palmbus0
gpiobus0: <OFW GPIO bus> on gpio0
random: harvesting attach, 8 bytes (4 bits) from gpiobus0
random: harvesting attach, 8 bytes (4 bits) from gpio0
cpulist0: <Open Firmware CPU Group> on ofwbus0
random: harvesting attach, 8 bytes (4 bits) from cpulist0
palmbus0: <timer@100> mem 0x100-0x11f irq 2 disabled compat ralink,rt2880-timer 
(no driver attached)
palmbus0: <watchdog@120> mem 0x120-0x12f compat ralink,rt2880-wdt (no driver att
ached)
palmbus0: <memc@300> mem 0x300-0x3ff compat ralink,rt2880-memc (no driver attach
ed)
gpioc0: <GPIO controller> on gpio0
random: harvesting attach, 8 bytes (4 bits) from gpioc0
palmbus0: <gpio@638> mem 0x638-0x65b disabled compat ralink,rt2880-gpio (no driv
er attached)
palmbus0: <gpio@660> mem 0x660-0x683 disabled compat ralink,rt2880-gpio (no driv
er attached)
iichb0: <MTK I2C Controller> mem 0x900-0x9ff on palmbus0
iicbus0: <OFW I2C bus> on iichb0
iicbus0: <unknown card> at addr 0xa8
iic0: <I2C generic I/O> on iicbus0
random: harvesting attach, 8 bytes (4 bits) from iic0
rtc85830: <EPSON RTC-8583> at addr 0xa0 on iicbus0
random: harvesting attach, 8 bytes (4 bits) from rtc85830
random: harvesting attach, 8 bytes (4 bits) from iicbus0
random: harvesting attach, 8 bytes (4 bits) from iichb0
uart0: <MTK UART Controller> mem 0xc00-0xcff irq 5 on palmbus0
uart0: console (57870,n,8,1)
uart0: fast interrupt
uart0: PPS capture mode: DCD
random: harvesting attach, 8 bytes (4 bits) from uart0
rt0: <Ralink RT2880 onChip Ethernet driver> mem 0x400000-0x40ffff irq 0 disabled
 on ofwbus0
rt0: RT305XF Ethernet MAC (rev 0x00000000)
rt0: use hardcoded 00:18:e7:d5:83:90 macaddr
rt0: bpf attached
rt0: Ethernet address: 00:18:e7:d5:83:90
random: harvesting attach, 8 bytes (4 bits) from rt0
ofwbus0: <mdio-bus> mem 0x400000-0x40ffff compat ralink,rt2880-mdio (no driver a
ttached)
ofwbus0: <wmac@480000> mem 0x480000-0x4bffff irq 1 compat ralink,rt2880-wmac (no
 driver attached)
cfi0: <AMD/Fujitsu - 4MB> mem 0x1f000000-0x1f7fffff on ofwbus0
cfi0: [8x8KB,63x64KB]
cfid0 on cfi0
random: harvesting attach, 8 bytes (4 bits) from cfid0
random: harvesting attach, 8 bytes (4 bits) from cfi0
gpioled0: <GPIO LEDs> on ofwbus0
random: harvesting attach, 8 bytes (4 bits) from gpioled0
ofwbus0: <gpio-keys-polled> compat gpio-keys-polled (no driver attached)
gpioiic0: <GPIO I2C bit-banging FDT driver> on ofwbus0
iicbb0: <I2C bit-banging driver> on gpioiic0
iicbus1: <OFW I2C bus> on iicbb0 master-only
rtl8366rb1: <RTL8366SR Ethernet Switch Controller> at addr 0xa8 on iicbus1
rtl8366rb1: rev. 1
miibus0: <MII bus> on rtl8366rb1
ukphy0: <Generic IEEE 802.3u media interface> PHY 0 on miibus0
ukphy0: OUI 0x00e04c, model 0x0016, rev. 0
ukphy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000ba
seT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
random: harvesting attach, 8 bytes (4 bits) from ukphy0
random: harvesting attach, 8 bytes (4 bits) from miibus0
miibus1: <MII bus> on rtl8366rb1
ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus1
ukphy1: OUI 0x00e04c, model 0x0016, rev. 0
ukphy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000ba
seT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
random: harvesting attach, 8 bytes (4 bits) from ukphy1
random: harvesting attach, 8 bytes (4 bits) from miibus1
miibus2: <MII bus> on rtl8366rb1
ukphy2: <Generic IEEE 802.3u media interface> PHY 2 on miibus2
ukphy2: OUI 0x00e04c, model 0x0016, rev. 0
ukphy2:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000ba
seT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
random: harvesting attach, 8 bytes (4 bits) from ukphy2
random: harvesting attach, 8 bytes (4 bits) from miibus2
miibus3: <MII bus> on rtl8366rb1
ukphy3: <Generic IEEE 802.3u media interface> PHY 3 on miibus3
ukphy3: OUI 0x00e04c, model 0x0016, rev. 0
ukphy3:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000ba
seT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
random: harvesting attach, 8 bytes (4 bits) from ukphy3
random: harvesting attach, 8 bytes (4 bits) from miibus3
miibus4: <MII bus> on rtl8366rb1
ukphy4: <Generic IEEE 802.3u media interface> PHY 4 on miibus4
ukphy4: OUI 0x00e04c, model 0x0016, rev. 0
ukphy4:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000ba
seT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
random: harvesting attach, 8 bytes (4 bits) from ukphy4
random: harvesting attach, 8 bytes (4 bits) from miibus4
etherswitch0: <Switch controller> on rtl8366rb1
random: harvesting attach, 8 bytes (4 bits) from etherswitch0
random: harvesting attach, 8 bytes (4 bits) from rtl8366rb1
iic1: <I2C generic I/O> on iicbus1
random: harvesting attach, 8 bytes (4 bits) from iic1
random: harvesting attach, 8 bytes (4 bits) from iicbus1
random: harvesting attach, 8 bytes (4 bits) from iicbb0
random: harvesting attach, 8 bytes (4 bits) from gpioiic0
ofwbus0: <rtl8366rb> compat realtek,rtl8366rb (no driver attached)
clock0: <Generic MIPS32 ticker> on nexus0
Timecounter "MIPS32" frequency 133333333 Hz quality 800
Event timer "MIPS32" frequency 133333333 Hz quality 800
random: harvesting attach, 8 bytes (4 bits) from clock0
Device configuration finished.
Timecounters tick every 10.000 msec
lo0: bpf attached
vlan: initialized, using hash tables with chaining
tcp_init: net.inet.tcp.tcbhashsize auto tuned to 512
rtc85830: registered as a time-of-day clock, resolution 1.000000s
rtl8366rb1port0: link state changed to DOWN
rtl8366rb1port1: link state changed to DOWN
rtl8366rb1port2: link state changed to DOWN
rtl8366rb1port3: link state changed to DOWN
rtl8366rb1port4: link state changed to DOWN
GEOM: new disk cfid0
Trying to mount root from cd9660:cfid0s.rootfs.uzip []...
cfid0: slice 00000000-0002ffff: Bootloader (191KB)
cfid0: slice 00030000-0003ffff: Config (63KB)
cfid0: slice 00040000-0004ffff: Factory (63KB)
cfid0: slice 00050000-0013ffff: kernel (959KB)
cfid0: slice 00140000-003dffff: rootfs (2687KB)
cfid0: slice 003e0000-003fffff: Cimage (127KB)
MAP: No valid partition found at cfid0
MAP: No valid partition found at cfid0s.Bootloader
MAP: No valid partition found at cfid0s.Config
MAP: No valid partition found at cfid0s.Factory
MAP: No valid partition found at cfid0s.kernel
MAP: No valid partition found at cfid0s.rootfs
MAP: No valid partition found at cfid0s.Cimage
MAP: No valid partition found at cfid0s.rootfs.uzip
cd9660: RockRidge Extension
rtc85830: providing initial system time
start_init: trying /sbin/init
rtl8366rb1port2: link state changed to UP
kenv: unable to get HostName

kern.coredump: 1 -> 0
net.inet.ip.forwarding: 0 -> 1
memory disk size = 4m
MAP: No valid partition found at md0
random: unblocking device.
MAP: No valid partition found at md0
port0:
        pvid: 1
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port1:
        pvid: 1
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port2:
        pvid: 1
        flags=0<>
        media: Ethernet autoselect (100baseTX <full-duplex>)
        status: active
port3:
        pvid: 1
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port4:
        pvid: 1
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port5:
        pvid: 1
        flags=1<CPUPORT>
        media: Ethernet 1000baseT <full-duplex,rxpause,txpause>
        status: active
vlangroup0:
        vlan: 1
        members 0,1,2,3,4,5
vlangroup1:
        vlan: 2
        members none

Mon Oct 30 17:18:46 UTC 2017
login: