Last active
August 14, 2019 18:46
-
-
Save yorickvP/d73f3d9ef22d64132f1bfe0711899e65 to your computer and use it in GitHub Desktop.
9260 iw-list
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| Wiphy phy0 | |
| max # scan SSIDs: 20 | |
| max scan IEs length: 422 bytes | |
| max # sched scan SSIDs: 20 | |
| max # match sets: 11 | |
| max # scan plans: 2 | |
| max scan plan interval: 65535 | |
| max scan plan iterations: 254 | |
| Retry short limit: 7 | |
| Retry long limit: 4 | |
| Coverage class: 0 (up to 0m) | |
| Device supports RSN-IBSS. | |
| Device supports AP-side u-APSD. | |
| Device supports T-DLS. | |
| Supported Ciphers: | |
| * WEP40 (00-0f-ac:1) | |
| * WEP104 (00-0f-ac:5) | |
| * TKIP (00-0f-ac:2) | |
| * CCMP-128 (00-0f-ac:4) | |
| * GCMP-128 (00-0f-ac:8) | |
| * GCMP-256 (00-0f-ac:9) | |
| * CMAC (00-0f-ac:6) | |
| * GMAC-128 (00-0f-ac:11) | |
| * GMAC-256 (00-0f-ac:12) | |
| Available Antennas: TX 0 RX 0 | |
| Supported interface modes: | |
| * IBSS | |
| * managed | |
| * AP | |
| * AP/VLAN | |
| * monitor | |
| * P2P-client | |
| * P2P-GO | |
| * P2P-device | |
| Band 1: | |
| Capabilities: 0x19ef | |
| RX LDPC | |
| HT20/HT40 | |
| SM Power Save disabled | |
| RX HT20 SGI | |
| RX HT40 SGI | |
| TX STBC | |
| RX STBC 1-stream | |
| Max AMSDU length: 7935 bytes | |
| DSSS/CCK HT40 | |
| Maximum RX AMPDU length 65535 bytes (exponent: 0x003) | |
| Minimum RX AMPDU time spacing: 4 usec (0x05) | |
| HT Max RX data rate: 300 Mbps | |
| HT TX/RX MCS rate indexes supported: 0-15 | |
| Bitrates (non-HT): | |
| * 1.0 Mbps | |
| * 2.0 Mbps (short preamble supported) | |
| * 5.5 Mbps (short preamble supported) | |
| * 11.0 Mbps (short preamble supported) | |
| * 6.0 Mbps | |
| * 9.0 Mbps | |
| * 12.0 Mbps | |
| * 18.0 Mbps | |
| * 24.0 Mbps | |
| * 36.0 Mbps | |
| * 48.0 Mbps | |
| * 54.0 Mbps | |
| Frequencies: | |
| * 2412 MHz [1] (20.0 dBm) | |
| * 2417 MHz [2] (20.0 dBm) | |
| * 2422 MHz [3] (20.0 dBm) | |
| * 2427 MHz [4] (20.0 dBm) | |
| * 2432 MHz [5] (20.0 dBm) | |
| * 2437 MHz [6] (20.0 dBm) | |
| * 2442 MHz [7] (20.0 dBm) | |
| * 2447 MHz [8] (20.0 dBm) | |
| * 2452 MHz [9] (20.0 dBm) | |
| * 2457 MHz [10] (20.0 dBm) | |
| * 2462 MHz [11] (20.0 dBm) | |
| * 2467 MHz [12] (20.0 dBm) | |
| * 2472 MHz [13] (20.0 dBm) | |
| Band 2: | |
| Capabilities: 0x19ef | |
| RX LDPC | |
| HT20/HT40 | |
| SM Power Save disabled | |
| RX HT20 SGI | |
| RX HT40 SGI | |
| TX STBC | |
| RX STBC 1-stream | |
| Max AMSDU length: 7935 bytes | |
| DSSS/CCK HT40 | |
| Maximum RX AMPDU length 65535 bytes (exponent: 0x003) | |
| Minimum RX AMPDU time spacing: 4 usec (0x05) | |
| HT Max RX data rate: 300 Mbps | |
| HT TX/RX MCS rate indexes supported: 0-15 | |
| VHT Capabilities (0x039071f6): | |
| Max MPDU length: 11454 | |
| Supported Channel Width: 160 MHz | |
| RX LDPC | |
| short GI (80 MHz) | |
| short GI (160/80+80 MHz) | |
| TX STBC | |
| SU Beamformee | |
| MU Beamformee | |
| VHT RX MCS set: | |
| 1 streams: MCS 0-9 | |
| 2 streams: MCS 0-9 | |
| 3 streams: not supported | |
| 4 streams: not supported | |
| 5 streams: not supported | |
| 6 streams: not supported | |
| 7 streams: not supported | |
| 8 streams: not supported | |
| VHT RX highest supported: 0 Mbps | |
| VHT TX MCS set: | |
| 1 streams: MCS 0-9 | |
| 2 streams: MCS 0-9 | |
| 3 streams: not supported | |
| 4 streams: not supported | |
| 5 streams: not supported | |
| 6 streams: not supported | |
| 7 streams: not supported | |
| 8 streams: not supported | |
| VHT TX highest supported: 0 Mbps | |
| Bitrates (non-HT): | |
| * 6.0 Mbps | |
| * 9.0 Mbps | |
| * 12.0 Mbps | |
| * 18.0 Mbps | |
| * 24.0 Mbps | |
| * 36.0 Mbps | |
| * 48.0 Mbps | |
| * 54.0 Mbps | |
| Frequencies: | |
| * 5180 MHz [36] (20.0 dBm) (no IR) | |
| * 5200 MHz [40] (20.0 dBm) (no IR) | |
| * 5220 MHz [44] (20.0 dBm) (no IR) | |
| * 5240 MHz [48] (20.0 dBm) (no IR) | |
| * 5260 MHz [52] (20.0 dBm) (no IR, radar detection) | |
| * 5280 MHz [56] (20.0 dBm) (no IR, radar detection) | |
| * 5300 MHz [60] (20.0 dBm) (no IR, radar detection) | |
| * 5320 MHz [64] (20.0 dBm) (no IR, radar detection) | |
| * 5500 MHz [100] (22.0 dBm) (no IR, radar detection) | |
| * 5520 MHz [104] (22.0 dBm) (no IR, radar detection) | |
| * 5540 MHz [108] (22.0 dBm) (no IR, radar detection) | |
| * 5560 MHz [112] (22.0 dBm) (no IR, radar detection) | |
| * 5580 MHz [116] (22.0 dBm) (no IR, radar detection) | |
| * 5600 MHz [120] (22.0 dBm) (no IR, radar detection) | |
| * 5620 MHz [124] (22.0 dBm) (no IR, radar detection) | |
| * 5640 MHz [128] (22.0 dBm) (no IR, radar detection) | |
| * 5660 MHz [132] (22.0 dBm) (no IR, radar detection) | |
| * 5680 MHz [136] (22.0 dBm) (no IR, radar detection) | |
| * 5700 MHz [140] (22.0 dBm) (no IR, radar detection) | |
| * 5720 MHz [144] (disabled) | |
| * 5745 MHz [149] (13.0 dBm) | |
| * 5765 MHz [153] (13.0 dBm) | |
| * 5785 MHz [157] (13.0 dBm) | |
| * 5805 MHz [161] (13.0 dBm) | |
| * 5825 MHz [165] (13.0 dBm) | |
| Supported commands: | |
| * new_interface | |
| * set_interface | |
| * new_key | |
| * start_ap | |
| * new_station | |
| * set_bss | |
| * authenticate | |
| * associate | |
| * deauthenticate | |
| * disassociate | |
| * join_ibss | |
| * remain_on_channel | |
| * set_tx_bitrate_mask | |
| * frame | |
| * frame_wait_cancel | |
| * set_wiphy_netns | |
| * set_channel | |
| * set_wds_peer | |
| * tdls_mgmt | |
| * tdls_oper | |
| * start_sched_scan | |
| * probe_client | |
| * set_noack_map | |
| * register_beacons | |
| * start_p2p_device | |
| * set_mcast_rate | |
| * connect | |
| * disconnect | |
| * channel_switch | |
| * set_qos_map | |
| * add_tx_ts | |
| * set_multicast_to_unicast | |
| Supported TX frame types: | |
| * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| Supported RX frame types: | |
| * IBSS: 0x40 0xb0 0xc0 0xd0 | |
| * managed: 0x40 0xd0 | |
| * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 | |
| * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 | |
| * mesh point: 0xb0 0xc0 0xd0 | |
| * P2P-client: 0x40 0xd0 | |
| * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 | |
| * P2P-device: 0x40 0xd0 | |
| WoWLAN support: | |
| * wake up on disconnect | |
| * wake up on magic packet | |
| * wake up on pattern match, up to 20 patterns of 16-128 bytes, | |
| maximum packet offset 0 bytes | |
| * can do GTK rekeying | |
| * wake up on GTK rekey failure | |
| * wake up on EAP identity request | |
| * wake up on 4-way handshake | |
| * wake up on rfkill release | |
| * wake up on network detection, up to 11 match sets | |
| software interface modes (can always be added): | |
| * AP/VLAN | |
| * monitor | |
| valid interface combinations: | |
| * #{ managed } <= 1, #{ AP, P2P-client, P2P-GO } <= 1, #{ P2P-device } <= 1, | |
| total <= 3, #channels <= 2 | |
| HT Capability overrides: | |
| * MCS: ff ff ff ff ff ff ff ff ff ff | |
| * maximum A-MSDU length | |
| * supported channel width | |
| * short GI for 40 MHz | |
| * max A-MPDU length exponent | |
| * min MPDU start spacing | |
| Device supports TX status socket option. | |
| Device supports HT-IBSS. | |
| Device supports SAE with AUTHENTICATE command | |
| Device supports low priority scan. | |
| Device supports scan flush. | |
| Device supports per-vif TX power setting | |
| P2P GO supports CT window setting | |
| P2P GO supports opportunistic powersave setting | |
| Driver supports full state transitions for AP/GO clients | |
| Driver supports a userspace MPM | |
| Driver/device bandwidth changes during BSS lifetime (AP/GO mode) | |
| Device adds DS IE to probe requests | |
| Device can update TPC Report IE | |
| Device supports static SMPS | |
| Device supports dynamic SMPS | |
| Device supports WMM-AC admission (TSPECs) | |
| Device supports configuring vdev MAC-addr on create. | |
| Device supports randomizing MAC-addr in scans. | |
| Device supports randomizing MAC-addr in sched scans. | |
| Device supports randomizing MAC-addr in net-detect scans. | |
| Supported extended features: | |
| * [ RRM ]: RRM | |
| * [ MU_MIMO_AIR_SNIFFER ]: MU-MIMO sniffer | |
| * [ SCAN_START_TIME ]: scan start timestamp | |
| * [ BSS_PARENT_TSF ]: BSS last beacon/probe TSF | |
| * [ SET_SCAN_DWELL ]: scan dwell setting | |
| * [ FILS_STA ]: STA FILS (Fast Initial Link Setup) | |
| * [ FILS_MAX_CHANNEL_TIME ]: FILS max channel attribute override with dwell time | |
| * [ ACCEPT_BCAST_PROBE_RESP ]: accepts broadcast probe response | |
| * [ OCE_PROBE_REQ_HIGH_TX_RATE ]: probe request TX at high rate (at least 5.5Mbps) | |
| * [ OCE_PROBE_REQ_DEFERRAL_SUPPRESSION ]: probe request tx deferral and suppression | |
| * [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211 |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment