Skip to content

Instantly share code, notes, and snippets.

Embed
What would you like to do?
;A20 PAD application
;-------------------------------------------------------------------------------
; 说明:
; 1. 脚本中的字符串区分大小写,用户可以修改"="后面的数值,但是不要修改前面的字符串
; 2. 新增主键和子键的名称必须控制在32个字符以内,不包括32个
; 3. 所以的注释以“;”开始,单独占据一行
; 4. 注释不可和配置项同行,例如:主键和子健后面不能添加任何形式的注释
;
; gpio的描述形式:Port:端口+组内序号<功能分配><内部电阻状态><驱动能力><输出电平状态>
; 例如:port:PA0<0><default><default><default>
;-------------------------------------------------------------------------------
[product]
version = "100"
machine = "evb-v10"
[platform]
eraseflag = 0
[target]
boot_clock = 912
dcdc2_vol = 1400
dcdc3_vol = 1200
ldo2_vol = 3000
ldo3_vol = 2800
ldo4_vol = 2800
storage_type = -1
[clock]
pll3 = 297
pll4 = 300
pll6 = 600
pll7 = 297
pll8 = 336
[card_boot]
logical_start = 40960
sprite_gpio0 =
[card0_boot_para]
card_ctrl = 0
card_high_speed = 1
card_line = 4
sdc_d1 = port:PF0<2><1><default><default>
sdc_d0 = port:PF1<2><1><default><default>
sdc_clk = port:PF2<2><1><default><default>
sdc_cmd = port:PF3<2><1><default><default>
sdc_d3 = port:PF4<2><1><default><default>
sdc_d2 = port:PF5<2><1><default><default>
[card2_boot_para]
card_ctrl = 2
card_high_speed = 1
card_line = 4
sdc_cmd = port:PC6<3><1>
sdc_clk = port:PC7<3><1>
sdc_d0 = port:PC8<3><1>
sdc_d1 = port:PC9<3><1>
sdc_d2 = port:PC10<3><1>
sdc_d3 = port:PC11<3><1>
[twi_para]
twi_port = 0
twi_scl = port:PB0<2><default><default><default>
twi_sda = port:PB1<2><default><default><default>
[uart_para]
uart_debug_port = 0
uart_debug_tx = port:PB22<2><1><default><default>
uart_debug_rx = port:PB23<2><1><default><default>
[uart_force_debug]
uart_debug_port = 0
uart_debug_tx =port:PB22<2><1><default><default>
uart_debug_rx =port:PB23<2><1><default><default>
[jtag_para]
jtag_enable = 0
jtag_ms = port:PB14<3><default><default><default>
jtag_ck = port:PB15<3><default><default><default>
jtag_do = port:PB16<3><default><default><default>
jtag_di = port:PB17<3><default><default><default>
;---------------------------------------------------------------------------------------------------------
; if 1 == standby_mode, then support super standby;
; else, support normal standby.
;---------------------------------------------------------------------------------------------------------
[pm_para]
standby_mode = 0
;-------------------------------------------------------------------------------
;sdram configuration
;-------------------------------------------------------------------------------
[dram_para]
dram_baseaddr = 0x40000000
dram_clk = 408
dram_type = 3
dram_rank_num = 0xffffffff
dram_chip_density = 0xffffffff
dram_io_width = 0xffffffff
dram_bus_width = 0xffffffff
dram_cas = 9
dram_zq = 0x7b
dram_odt_en = 0
dram_size = 0xffffffff
dram_tpr0 = 0x42d899b7
dram_tpr1 = 0xa090
dram_tpr2 = 0x22a00
dram_tpr3 = 0x0
dram_tpr4 = 0x0
dram_tpr5 = 0x0
dram_emr1 = 0x4
dram_emr2 = 0x10
dram_emr3 = 0x0
;-------------------------------------------------------------------------------
;Mali configuration
;-------------------------------------------------------------------------------
[mali_para]
mali_used = 1
mali_clkdiv = 1
;-------------------------------------------------------------------------------
;Ethernet MAC configuration
;-------------------------------------------------------------------------------
[emac_para]
emac_used = 0
emac_rxd3 = port:PA00<2><default><default><default>
emac_rxd2 = port:PA01<2><default><default><default>
emac_rxd1 = port:PA02<2><default><default><default>
emac_rxd0 = port:PA03<2><default><default><default>
emac_txd3 = port:PA04<2><default><default><default>
emac_txd2 = port:PA05<2><default><default><default>
emac_txd1 = port:PA06<2><default><default><default>
emac_txd0 = port:PA07<2><default><default><default>
emac_rxclk = port:PA08<2><default><default><default>
emac_rxerr = port:PA09<2><default><default><default>
emac_rxdV = port:PA10<2><default><default><default>
emac_mdc = port:PA11<2><default><default><default>
emac_mdio = port:PA12<2><default><default><default>
emac_txen = port:PA13<2><default><default><default>
emac_txclk = port:PA14<2><default><default><default>
emac_crs = port:PA15<2><default><default><default>
emac_col = port:PA16<2><default><default><default>
emac_reset = port:PA17<1><default><default><default>
;-------------------------------------------------------------------------------
;i2c configuration
;-------------------------------------------------------------------------------
[twi0_para]
twi0_used = 1
twi0_scl = port:PB0<2><default><default><default>
twi0_sda = port:PB1<2><default><default><default>
[twi1_para]
twi1_used = 1
twi1_scl = port:PB18<2><default><default><default>
twi1_sda = port:PB19<2><default><default><default>
[twi2_para]
twi2_used = 1
twi2_scl = port:PB20<2><default><default><default>
twi2_sda = port:PB21<2><default><default><default>
;-------------------------------------------------------------------------------
;uart configuration
;uart_type --- 2 (2 wire), 4 (4 wire), 8 (8 wire, full function)
;-------------------------------------------------------------------------------
[uart_para0]
uart_used = 1
uart_port = 0
uart_type = 2
uart_tx = port:PB22<2><1><default><default>
uart_rx = port:PB23<2><1><default><default>
[uart_para1]
uart_used = 0
uart_port = 1
uart_type = 8
uart_tx = port:PA10<4><1><default><default>
uart_rx = port:PA11<4><1><default><default>
uart_rts = port:PA12<4><1><default><default>
uart_cts = port:PA13<4><1><default><default>
uart_dtr = port:PA14<4><1><default><default>
uart_dsr = port:PA15<4><1><default><default>
uart_dcd = port:PA16<4><1><default><default>
uart_ring = port:PA17<4><1><default><default>
[uart_para2]
uart_used = 1
uart_port = 2
uart_type = 4
uart_tx = port:PI18<3><1><default><default>
uart_rx = port:PI19<3><1><default><default>
uart_rts = port:PI16<3><1><default><default>
uart_cts = port:PI17<3><1><default><default>
[uart_para3]
uart_used = 0
uart_port = 3
uart_type = 4
uart_tx = port:PH00<4><1><default><default>
uart_rx = port:PH01<4><1><default><default>
uart_rts = port:PH02<4><1><default><default>
uart_cts = port:PH03<4><1><default><default>
[uart_para4]
uart_used = 0
uart_port = 4
uart_type = 2
uart_tx = port:PH04<4><1><default><default>
uart_rx = port:PH05<4><1><default><default>
[uart_para5]
uart_used = 0
uart_port = 5
uart_type = 2
uart_tx = port:PI10<3><1><default><default>
uart_rx = port:PI11<3><1><default><default>
[uart_para6]
uart_used = 0
uart_port = 6
uart_type = 2
uart_tx = port:PI12<3><1><default><default>
uart_rx = port:PI13<3><1><default><default>
[uart_para7]
uart_used = 0
uart_port = 7
uart_type = 2
uart_tx = port:PI20<3><1><default><default>
uart_rx = port:PI21<3><1><default><default>
;-------------------------------------------------------------------------------
;spi configuration
;-------------------------------------------------------------------------------
[spi0_para]
spi_used = 0
spi_cs_bitmap = 1
spi_cs0 = port:PI10<2><default><default><default>
spi_cs1 = port:PI14<2><default><default><default>
spi_sclk = port:PI11<2><default><default><default>
spi_mosi = port:PI12<2><default><default><default>
spi_miso = port:PI13<2><default><default><default>
[spi1_para]
spi_used = 0
spi_cs_bitmap = 1
spi_cs0 = port:PA00<3><default><default><default>
spi_cs1 = port:PA04<3><default><default><default>
spi_sclk = port:PA01<3><default><default><default>
spi_mosi = port:PA02<3><default><default><default>
spi_miso = port:PA03<3><default><default><default>
[spi2_para]
spi_used = 0
spi_cs_bitmap = 1
spi_cs0 = port:PC19<3><default><default><default>
spi_cs1 = port:PB13<2><default><default><default>
spi_sclk = port:PC20<3><default><default><default>
spi_mosi = port:PC21<3><default><default><default>
spi_miso = port:PC22<3><default><default><default>
[spi3_para]
spi_used = 0
spi_cs_bitmap = 1
spi_cs0 = port:PA05<3><default><default><default>
spi_cs1 = port:PA09<3><default><default><default>
spi_sclk = port:PA06<3><default><default><default>
spi_mosi = port:PA07<3><default><default><default>
spi_miso = port:PA08<3><default><default><default>
;----------------------------------------------------------------------------------
;resistance tp configuration
;----------------------------------------------------------------------------------
[rtp_para]
rtp_used = 0
rtp_screen_size = 5
rtp_regidity_level = 5
rtp_press_threshold_enable = 0
rtp_press_threshold = 0x1f40
rtp_sensitive_level = 0xf
rtp_exchange_x_y_flag = 0
;-------------------------------------------------------------------------------
;capacitor tp configuration
;external int function
;wakeup output function
;notice:
; tp_int_port & tp_io_port use the same port
;-------------------------------------------------------------------------------
[ctp_para]
ctp_used = 0
ctp_twi_id = 2
ctp_twi_name =
ctp_screen_max_x = 800
ctp_screen_max_y = 480
ctp_revert_x_flag = 0
ctp_revert_y_flag = 0
ctp_exchange_x_y_flag = 0
ctp_int_port = port:PH21<6><default><default><default>
ctp_wakeup = port:PB13<1><default><default><1>
;-------------------------------------------------------------------------------
;touch key configuration
;-------------------------------------------------------------------------------
[tkey_para]
tkey_used = 0
tkey_twi_id = 2
tkey_twi_addr = 0x62
tkey_int = port:PI13<6><default><default><default>
;-------------------------------------------------------------------------------
;motor configuration
;-------------------------------------------------------------------------------
[motor_para]
motor_used = 0
motor_shake = port:PB03<1><default><default><1>
;-------------------------------------------------------------------------------
;nand flash configuration
;-------------------------------------------------------------------------------
[nand_para]
nand_used = 1
nand_we = port:PC00<2><default><default><default>
nand_ale = port:PC01<2><default><default><default>
nand_cle = port:PC02<2><default><default><default>
nand_ce1 = port:PC03<2><default><default><default>
nand_ce0 = port:PC04<2><default><default><default>
nand_nre = port:PC05<2><default><default><default>
nand_rb0 = port:PC06<2><default><default><default>
nand_rb1 = port:PC07<2><default><default><default>
nand_d0 = port:PC08<2><default><default><default>
nand_d1 = port:PC09<2><default><default><default>
nand_d2 = port:PC10<2><default><default><default>
nand_d3 = port:PC11<2><default><default><default>
nand_d4 = port:PC12<2><default><default><default>
nand_d5 = port:PC13<2><default><default><default>
nand_d6 = port:PC14<2><default><default><default>
nand_d7 = port:PC15<2><default><default><default>
nand_wp = port:PC16<2><default><default><default>
nand_ce2 = port:PC17<2><default><default><default>
nand_ce3 = port:PC18<2><default><default><default>
nand_ce4 =
nand_ce5 =
nand_ce6 =
nand_ce7 =
nand_spi = port:PC23<3><default><default><default>
nand_ndqs = port:PC24<2><default><default><default>
good_block_ratio = 0
;-------------------------------------------------------------------------------
;disp init configuration
;
;disp_mode (0:screen0<screen0,fb0> 1:screen1<screen1,fb0> 2:two_diff_screen_diff_contents<screen0,screen1,fb0,fb1>
; 3:two_same_screen_diff_contets<screen0,screen1,fb0> 4:two_diff_screen_same_contents<screen0,screen1,fb0>)
;screenx_output_type (0:none; 1:lcd; 2:tv; 3:hdmi; 4:vga)
;screenx_output_mode (used for tv/hdmi output, 0:480i 1:576i 2:480p 3:576p 4:720p50 5:720p60 6:1080i50 7:1080i60 8:1080p24 9:1080p50 10:1080p60 11:pal 14:ntsc)
;screenx_output_mode (used for vga output, 0:1680*1050 1:1440*900 2:1360*768 3:1280*1024 4:1024*768 5:800*600 6:640*480 10:1920*1080 11:1280*720)
;fbx format (4:RGB655 5:RGB565 6:RGB556 7:ARGB1555 8:RGBA5551 9:RGB888 10:ARGB8888 12:ARGB4444)
;fbx pixel sequence (0:ARGB 1:BGRA 2:ABGR 3:RGBA) --- 0 for linux, 2 for android
;lcd0_bright (lcd0 init bright,the range:[0,256],default:197
;lcd1_bright (lcd1 init bright,the range:[0,256],default:197
;-------------------------------------------------------------------------------
[disp_init]
disp_init_enable = 1
disp_mode = 0
screen0_output_type = 1
screen0_output_mode = 4
screen1_output_type = 3
screen1_output_mode = 4
fb0_framebuffer_num = 2
fb0_format = 10
fb0_pixel_sequence = 0
fb0_scaler_mode_enable = 0
fb1_framebuffer_num = 2
fb1_format = 10
fb1_pixel_sequence = 0
fb1_scaler_mode_enable = 0
lcd0_backlight = 197
lcd1_backlight = 197
lcd0_bright = 50
lcd0_contrast = 50
lcd0_saturation = 57
lcd0_hue = 50
lcd1_bright = 50
lcd1_contrast = 50
lcd1_saturation = 57
lcd1_hue = 50
;-------------------------------------------------------------------------------
;lcd0 configuration
;lcd_dclk_freq: in MHZ unit
;lcd_pwm_freq: in HZ unit
;lcd_if: 0:hv(sync+de); 1:8080; 2:ttl; 3:lvds
;lcd_hbp: hsync back porch
;lcd_ht: hsync total cycle
;lcd_vbp: vsync back porch
;lcd_vt: vysnc total cycle *2
;lcd_hv_if: 0:hv parallel 1:hv serial
;lcd_hv_smode: 0:RGB888 1:CCIR656
;lcd_hv_s888_if serial RGB format
;lcd_hv_syuv_if: serial YUV format
;lcd_hspw: hsync plus width
;lcd_vspw: vysnc plus width
;lcd_lvds_ch: 0:single channel; 1:dual channel
;lcd_lvds_mode: 0:NS mode; 1:JEIDA mode
;lcd_lvds_bitwidth: 0:24bit; 1:18bit
;lcd_lvds_io_cross: 0:normal; 1:pn cross
;lcd_cpu_if: 0:18bit; 1:16bit mode0; 2:16bit mode1; 3:16bit mode2; 4:16bit mode3; 5:9bit; 6:8bit 256K; 7:8bit 65K
;lcd_frm: 0:disable; 1:enable rgb666 dither; 2:enable rgb656 dither
;lcd_gpio_0: SCL
;lcd_gpio_1 SDA
;-------------------------------------------------------------------------------
[lcd0_para]
lcd_used = 1
lcd_x = 1024
lcd_y = 600
lcd_dclk_freq = 52
lcd_pwm_not_used = 0
lcd_pwm_ch = 0
lcd_pwm_freq = 10000
lcd_pwm_pol = 1
lcd_if = 3
lcd_hbp = 33
lcd_ht = 1344
lcd_vbp = 23
lcd_vt = 1270
lcd_vspw = 0
lcd_hspw = 0
lcd_hv_if = 0
lcd_hv_smode = 0
lcd_hv_s888_if = 0
lcd_hv_syuv_if = 0
lcd_lvds_ch = 0
lcd_lvds_mode = 0
lcd_lvds_bitwidth = 0
lcd_lvds_io_cross = 0
lcd_cpu_if = 0
lcd_frm = 1
lcd_io_cfg0 = 0x10000000
lcd_gamma_correction_en = 0
lcd_gamma_tbl_0 = 0x00000000
lcd_gamma_tbl_1 = 0x00010101
lcd_gamma_tbl_255 = 0x00ffffff
lcd_bl_en_used = 1
lcd_bl_en = port:PH07<1><0><default><1>
lcd_power_used = 1
lcd_power = port:PH08<1><0><default><1>
lcd_pwm_used = 1
lcd_pwm = port:PB02<2><0><default><default>
lcdd0 = port:PD00<2><0><default><default>
lcdd1 = port:PD01<2><0><default><default>
lcdd2 = port:PD02<2><0><default><default>
lcdd3 = port:PD03<2><0><default><default>
lcdd4 = port:PD04<2><0><default><default>
lcdd5 = port:PD05<2><0><default><default>
lcdd6 = port:PD06<2><0><default><default>
lcdd7 = port:PD07<2><0><default><default>
lcdd8 = port:PD08<2><0><default><default>
lcdd9 = port:PD09<2><0><default><default>
lcdd10 = port:PD10<2><0><default><default>
lcdd11 = port:PD11<2><0><default><default>
lcdd12 = port:PD12<2><0><default><default>
lcdd13 = port:PD13<2><0><default><default>
lcdd14 = port:PD14<2><0><default><default>
lcdd15 = port:PD15<2><0><default><default>
lcdd16 = port:PD16<2><0><default><default>
lcdd17 = port:PD17<2><0><default><default>
lcdd18 = port:PD18<2><0><default><default>
lcdd19 = port:PD19<2><0><default><default>
lcdd20 = port:PD20<2><0><default><default>
lcdd21 = port:PD21<2><0><default><default>
lcdd22 = port:PD22<2><0><default><default>
lcdd23 = port:PD23<2><0><default><default>
lcdclk = port:PD24<2><0><default><default>
lcdde = port:PD25<2><0><default><default>
lcdhsync = port:PD26<2><0><default><default>
lcdvsync = port:PD27<2><0><default><default>
;----------------------------------------------------------------------------------
;lcd1 configuration
;lcd_dclk_freq: in MHZ unit
;lcd_pwm_freq: in HZ unit
;lcd_if: 0:hv(sync+de); 1:8080; 2:ttl; 3:lvds
;lcd_hbp: hsync back porch
;lcd_ht: hsync total cycle
;lcd_vbp: vsync back porch
;lcd_vt: vysnc total cycle *2
;lcd_hv_if: 0:hv parallel 1:hv serial
;lcd_hv_smode: 0:RGB888 1:CCIR656
;lcd_hv_s888_if serial RGB format
;lcd_hv_syuv_if: serial YUV format
;lcd_hspw: hsync plus width
;lcd_vspw: vysnc plus width
;lcd_lvds_ch: 0:single channel; 1:dual channel
;lcd_lvds_mode: 0:NS mode; 1:JEIDA mode
;lcd_lvds_bitwidth: 0:24bit; 1:18bit
;lcd_lvds_io_cross: 0:normal; 1:pn cross
;lcd_cpu_if: 0:18bit; 1:16bit mode0; 2:16bit mode1; 3:16bit mode2; 4:16bit mode3; 5:9bit; 6:8bit 256K; 7:8bit 65K
;lcd_frm: 0:disable; 1:enable rgb666 dither; 2:enable rgb656 dither
;lcd_gpio_0: SCL
;lcd_gpio_1 SDA
;----------------------------------------------------------------------------------
[lcd1_para]
lcd_used = 0
lcd_x = 0
lcd_y = 0
lcd_dclk_freq = 0
lcd_pwm_not_used = 0
lcd_pwm_ch = 1
lcd_pwm_freq = 0
lcd_pwm_pol = 0
lcd_if = 0
lcd_hbp = 0
lcd_ht = 0
lcd_vbp = 0
lcd_vt = 0
lcd_vspw = 0
lcd_hspw = 0
lcd_hv_if = 0
lcd_hv_smode = 0
lcd_hv_s888_if = 0
lcd_hv_syuv_if = 0
lcd_lvds_ch = 0
lcd_lvds_mode = 0
lcd_lvds_bitwidth = 0
lcd_lvds_io_cross = 0
lcd_cpu_if = 0
lcd_frm = 0
lcd_io_cfg0 = 0
lcd_gamma_correction_en = 0
lcd_gamma_tbl_0 = 0x00000000
lcd_gamma_tbl_1 = 0x00010101
lcd_gamma_tbl_255 = 0x00ffffff
lcd_bl_en_used = 0
lcd_bl_en =
lcd_power_used = 0
lcd_power =
lcd_pwm_used = 1
lcd_pwm = port:PI03<2><0><default><default>
lcd_gpio_0 =
lcd_gpio_1 =
lcd_gpio_2 =
lcd_gpio_3 =
lcdd0 = port:PH00<2><0><default><default>
lcdd1 = port:PH01<2><0><default><default>
lcdd2 = port:PH02<2><0><default><default>
lcdd3 = port:PH03<2><0><default><default>
lcdd4 = port:PH04<2><0><default><default>
lcdd5 = port:PH05<2><0><default><default>
lcdd6 = port:PH06<2><0><default><default>
lcdd7 = port:PH07<2><0><default><default>
lcdd8 = port:PH08<2><0><default><default>
lcdd9 = port:PH09<2><0><default><default>
lcdd10 = port:PH10<2><0><default><default>
lcdd11 = port:PH11<2><0><default><default>
lcdd12 = port:PH12<2><0><default><default>
lcdd13 = port:PH13<2><0><default><default>
lcdd14 = port:PH14<2><0><default><default>
lcdd15 = port:PH15<2><0><default><default>
lcdd16 = port:PH16<2><0><default><default>
lcdd17 = port:PH17<2><0><default><default>
lcdd18 = port:PH18<2><0><default><default>
lcdd19 = port:PH19<2><0><default><default>
lcdd20 = port:PH20<2><0><default><default>
lcdd21 = port:PH21<2><0><default><default>
lcdd22 = port:PH22<2><0><default><default>
lcdd23 = port:PH23<2><0><default><default>
lcdclk = port:PH24<2><0><default><default>
lcdde = port:PH25<2><0><default><default>
lcdhsync = port:PH26<2><0><default><default>
lcdvsync = port:PH27<2><0><default><default>
;-------------------------------------------------------------------------------
;tv out dac configuration
;dacx_src: 0:composite; 1:luma; 2:chroma; 4:Y; 5:Pb; 6: Pr; 7:none
;-------------------------------------------------------------------------------
[tv_out_dac_para]
dac_used = 1
dac0_src = 4
dac1_src = 5
dac2_src = 6
dac3_src = 0
;----------------------------------------------------------------------------------
;hdmi configuration
;----------------------------------------------------------------------------------
[hdmi_para]
hdmi_used = 1
[camera_list_para]
camera_list_para_used = 0
ov7670 = 0
gc0308 = 1
gt2005 = 0
hi704 = 0
sp0838 = 0
mt9m112 = 0
mt9m113 = 0
ov2655 = 0
hi253 = 0
gc0307 = 0
mt9d112 = 0
ov5640 = 1
gc2015 = 0
ov2643 = 0
gc0329 = 0
gc0309 = 0
tvp5150 = 0
s5k4ec = 0
ov5650_mv9335 = 0
siv121d = 0
;--------------------------------------------------------------------------------
;csi gpio configuration
;csi_if: 0:hv_8bit 1:hv_16bit 2:hv_24bit 3:bt656 1ch 4:bt656 2ch 5:bt656 4ch
;csi_mode: 0:sample one csi to one buffer 1:sample two csi to one buffer
;csi_dev_qty: The quantity of devices linked to csi interface
;csi_vflip: flip in vertical direction 0:disable 1:enable
;csi_hflip: flip in horizontal direction 0:disable 1:enable
;csi_stby_mode: 0:not shut down power at standby 1:shut down power at standby
;csi_iovdd: camera module io power , pmu power supply
;csi_avdd: camera module analog power , pmu power supply
;csi_dvdd: camera module core power , pmu power supply
;pmu_ldo3: fill "axp20_pll"
;pmu_ldo4: fill "axp20_hdmi"
;fill "" when not using any pmu power supply
;csi_flash_pol: the active polority of the flash light IO 0:low active 1:high active
;--------------------------------------------------------------------------------
[csi0_para]
csi_used = 1
csi_dev_qty = 1
csi_stby_mode = 0
csi_mname = "gc0308"
csi_if = 0
csi_iovdd = ""
csi_avdd = ""
csi_dvdd = ""
csi_vol_iovdd =
csi_vol_dvdd =
csi_vol_avdd =
csi_vflip = 0
csi_hflip = 0
csi_flash_pol = 0
csi_facing = 0
csi_twi_id = 1
csi_twi_addr = 0x42
csi_pck = port:PE00<3><default><default><default>
csi_ck = port:PE01<3><default><default><default>
csi_hsync = port:PE02<3><default><default><default>
csi_vsync = port:PE03<3><default><default><default>
csi_d0 = port:PE04<3><default><default><default>
csi_d1 = port:PE05<3><default><default><default>
csi_d2 = port:PE06<3><default><default><default>
csi_d3 = port:PE07<3><default><default><default>
csi_d4 = port:PE08<3><default><default><default>
csi_d5 = port:PE09<3><default><default><default>
csi_d6 = port:PE10<3><default><default><default>
csi_d7 = port:PE11<3><default><default><default>
csi_reset = port:PH13<1><default><default><0>
csi_power_en = port:PH16<1><default><default><1>
csi_stby = port:PH18<1><default><default><1>
[csi1_para]
csi_used = 0
csi_dev_qty = 1
csi_stby_mode = 0
csi_mname = "gc0308"
csi_if = 0
csi_iovdd = ""
csi_avdd = ""
csi_dvdd = ""
csi_vol_iovdd =
csi_vol_dvdd =
csi_vol_avdd =
csi_vflip = 0
csi_hflip = 0
csi_flash_pol = 0
csi_facing = 1
csi_twi_id = 1
csi_twi_addr = 0x42
csi_pck = port:PG00<3><default><default><default>
csi_ck = port:PG01<3><default><default><default>
csi_hsync = port:PG02<3><default><default><default>
csi_vsync = port:PG03<3><default><default><default>
csi_d0 = port:PG04<3><default><default><default>
csi_d1 = port:PG05<3><default><default><default>
csi_d2 = port:PG06<3><default><default><default>
csi_d3 = port:PG07<3><default><default><default>
csi_d4 = port:PG08<3><default><default><default>
csi_d5 = port:PG09<3><default><default><default>
csi_d6 = port:PG10<3><default><default><default>
csi_d7 = port:PG11<3><default><default><default>
csi_reset = port:PH14<1><default><default><0>
csi_power_en =
csi_stby = port:PH17<1><default><default><0>
;-------------------------------------------------------------------------------
;tv configuration
;
;-------------------------------------------------------------------------------
[tvout_para]
tvout_used = 0
tvout_channel_num = 1
[tvin_para]
tvin_used = 0
tvin_channel_num = 4
;-------------------------------------------------------------------------------
;sata configuration
;
;-------------------------------------------------------------------------------
[sata_para]
sata_used = 0
sata_power_en =
;-------------------------------------------------------------------------------
; SDMMC PINS MAPPING
; ------------------------------------------------------------------------------
; Config Guide
; sdc_used: 1-enable card, 0-disable card
; sdc_detmode: card detect mode
; 1-detect card by gpio polling
; 2-detect card by gpio irq(must use IO with irq function)
; 3-no detect, always in for boot card
; 4-manually insert and remove by /proc/driver/sunxi-mmc.x/insert
; sdc_buswidth: card bus width, 1-1bit, 4-4bit, 8-8bit
; sdc_use_wp: 1-with write protect IO, 0-no write protect IO
; sdc_isio: for sdio card
; sdc_regulator: power control.
; other: GPIO Mapping configuration
; ------------------------------------------------------------------------------
; Note:
; 1 if detmode=2, sdc_det's config=6
; else if detmode=1, sdc_det's config=0
; else sdc_det IO is not necessary
; 2 if the customer wants to support UHS-I and HS200 features, he must provide
; an independent power supply for the card. This is only used in platforms
; that supports SD3.0 cards and eMMC4.4+ flashes
;-------------------------------------------------------------------------------
[mmc0_para]
sdc_used = 1
sdc_detmode = 1
sdc_buswidth = 4
sdc_clk = port:PF02<2><1><2><default>
sdc_cmd = port:PF03<2><1><2><default>
sdc_d0 = port:PF01<2><1><2><default>
sdc_d1 = port:PF00<2><1><2><default>
sdc_d2 = port:PF05<2><1><2><default>
sdc_d3 = port:PF04<2><1><2><default>
sdc_det = port:PH1<0><1><default><default>
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"
[mmc1_para]
sdc_used = 0
sdc_detmode = 4
sdc_buswidth = 4
sdc_clk = port:PG00<2><1><2><default>
sdc_cmd = port:PG01<2><1><2><default>
sdc_d0 = port:PG02<2><1><2><default>
sdc_d1 = port:PG03<2><1><2><default>
sdc_d2 = port:PG04<2><1><2><default>
sdc_d3 = port:PG05<2><1><2><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"
[mmc2_para]
sdc_used = 0
sdc_detmode = 3
sdc_buswidth = 4
sdc_cmd = port:PC06<3><1><2><default>
sdc_clk = port:PC07<3><1><2><default>
sdc_d0 = port:PC08<3><1><2><default>
sdc_d1 = port:PC09<3><1><2><default>
sdc_d2 = port:PC10<3><1><2><default>
sdc_d3 = port:PC11<3><1><2><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"
[mmc3_para]
sdc_used = 1
sdc_detmode = 4
sdc_buswidth = 4
sdc_cmd = port:PI04<2><1><2><default>
sdc_clk = port:PI05<2><1><2><default>
sdc_d0 = port:PI06<2><1><2><default>
sdc_d1 = port:PI07<2><1><2><default>
sdc_d2 = port:PI08<2><1><2><default>
sdc_d3 = port:PI09<2><1><2><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 1
sdc_regulator = "none"
; ------------------------------------------------------------------------------
; memory stick configuration
;-------------------------------------------------------------------------------
[ms_para]
ms_used = 0
ms_bs = port:PH06<5><default><default><default>
ms_clk = port:PH07<5><default><default><default>
ms_d0 = port:PH08<5><default><default><default>
ms_d1 = port:PH09<5><default><default><default>
ms_d2 = port:PH10<5><default><default><default>
ms_d3 = port:PH11<5><default><default><default>
ms_det =
; ------------------------------------------------------------------------------
; sim card configuration
;-------------------------------------------------------------------------------
[smc_para]
smc_used = 0
smc_rst = port:PH13<5><default><default><default>
smc_vppen = port:PH14<5><default><default><default>
smc_vppp = port:PH15<5><default><default><default>
smc_det = port:PH16<5><default><default><default>
smc_vccen = port:PH17<5><default><default><default>
smc_sck = port:PH18<5><default><default><default>
smc_sda = port:PH19<5><default><default><default>
;-------------------------------------------------------------------------------
;ps2 configuration
;-------------------------------------------------------------------------------
[ps2_0_para]
ps2_used = 0
ps2_scl = port:PI20<2><1><default><default>
ps2_sda = port:PI21<2><1><default><default>
[ps2_1_para]
ps2_used = 0
ps2_scl = port:PI14<3><1><default><default>
ps2_sda = port:PI15<3><1><default><default>
;-------------------------------------------------------------------------------
;can bus configuration
;-------------------------------------------------------------------------------
[can_para]
can_used = 0
can_tx = port:PA16<3><default><default><default>
can_rx = port:PA17<3><default><default><default>
;-------------------------------------------------------------------------------
;key matrix
;-------------------------------------------------------------------------------
[keypad_para]
kp_used = 0
kp_in_size = 8
kp_out_size = 8
kp_in0 = port:PH08<4><1><default><default>
kp_in1 = port:PH09<4><1><default><default>
kp_in2 = port:PH10<4><1><default><default>
kp_in3 = port:PH11<4><1><default><default>
kp_in4 = port:PH14<4><1><default><default>
kp_in5 = port:PH15<4><1><default><default>
kp_in6 = port:PH16<4><1><default><default>
kp_in7 = port:PH17<4><1><default><default>
kp_out0 = port:PH18<4><1><default><default>
kp_out1 = port:PH19<4><1><default><default>
kp_out2 = port:PH22<4><1><default><default>
kp_out3 = port:PH23<4><1><default><default>
kp_out4 = port:PH24<4><1><default><default>
kp_out5 = port:PH25<4><1><default><default>
kp_out6 = port:PH26<4><1><default><default>
kp_out7 = port:PH27<4><1><default><default>
;-------------------------------------------------------------------------------
;[usbc0]:控制器0的配置。
;usb_used:USB使能标志。置1,表示系统中USB模块可用,置0,则表示系统USB禁用。
;usb_port_type:USB端口的使用情况。 0:device only;1:host only;2:OTG
;usb_detect_type:USB端口的检查方式。0:不做检测;1:vbus/id检查;2:id/dpdm检查
;usb_id_gpio:USB ID pin脚配置。具体请参考gpio配置说明。
;usb_det_vbus_gpio:USB DET_VBUS pin脚配置。具体请参考gpio配置说明。
;usb_drv_vbus_gpio:USB DRY_VBUS pin脚配置。具体请参考gpio配置说明。
;usb_det_vbus_gpio: "axp_ctrl",表示axp 提供
;usb_restrict_gpio usb限流控制pin
;usb_restric_flag: usb限流标置
;-------------------------------------------------------------------------------
;-------------------------------------------------------------------------------
;--- USB0控制标志
;-------------------------------------------------------------------------------
[usbc0]
usb_used = 0
usb_port_type = 2
usb_detect_type = 1
usb_id_gpio = port:PH04<0><1><default><default>
usb_det_vbus_gpio = "axp_ctrl"
usb_drv_vbus_gpio = port:PB09<1><0><default><0>
usb_restrict_gpio = port:PH06<1><0><default><0>
usb_host_init_state = 0
usb_restric_flag = 0
usb_restric_voltage = 3550000
usb_restric_capacity= 5
;-------------------------------------------------------------------------------
;--- USB1控制标志
;------------------------------------------------------------------------------
[usbc1]
usb_used = 1
usb_port_type = 1
usb_detect_type = 0
usb_drv_vbus_gpio = port:PH12<1><0><default><0>
usb_restrict_gpio =
usb_host_init_state = 1
usb_restric_flag = 0
;------------------------------------------------------------------------------
;--- USB2控制标志
;------------------------------------------------------------------------------
[usbc2]
usb_used = 1
usb_port_type = 1
usb_detect_type = 0
usb_drv_vbus_gpio = port:PH03<1><0><default><0>
usb_restrict_gpio =
usb_host_init_state = 1
usb_restric_flag = 0
;--------------------------------
;--- USB Device
;--------------------------------
[usb_feature]
vendor_id = 0x18D1
mass_storage_id = 0x0001
adb_id = 0x0002
manufacturer_name = "USB Developer"
product_name = "Android"
serial_number = "20080411"
[msc_feature]
vendor_name = "USB 2.0"
product_name = "USB Flash Driver"
release = 100
luns = 3
;-------------------------------------------------------------------------------
; G sensor configuration
; gs_twi_id --- TWI ID for controlling Gsensor (0: TWI0, 1: TWI1, 2: TWI2)
;-------------------------------------------------------------------------------
[gsensor_para]
gsensor_used = 0
gsensor_twi_id = 1
gsensor_int1 =
gsensor_int2 =
;-------------------------------------------------------------------------------
; gps gpio configuration
; gps_spi_id --- the index of SPI controller. 0: SPI0, 1: SPI1, 2: SPI2, 15: no SPI used
; gps_spi_cs_num --- the chip select number of SPI controller. 0: SPI CS0, 1: SPI CS1
; gps_lradc --- the lradc number for GPS used. 0 and 1 is valid, set 2 if not use lradc
;-------------------------------------------------------------------------------
[gps_para]
gps_used = 0
gps_spi_id = 2
gps_spi_cs_num = 0
gps_lradc = 1
gps_clk = port:PI00<2><default><default><default>
gps_sign = port:PI01<2><default><default><default>
gps_mag = port:PI02<2><default><default><default>
gps_vcc_en = port:PC22<1><default><default><0>
gps_osc_en = port:PI14<1><default><default><0>
gps_rx_en = port:PI15<1><default><default><0>
;--------------------------------------------------------------------------------
;wifi configuration
;wifi_sdc_id --- 0- SDC0, 1- SDC1, 2- SDC2, 3- SDC3
;wifi_usbc_id --- 0- USB0, 1- USB1, 2- USB2
;wifi_usbc_type -- 1- EHCI(speed 2.0), 2- OHCI(speed 1.0)
;wifi_mod_sel --- 0- none, 1- bcm40181, 2- bcm40183(wifi+bt),
; 3 - rtl8723as(wifi+bt), 4- rtl8189es(SM89E00),
; 5 - rtl8192cu, 6 - rtl8188eu, 7 - ap6210
;--------------------------------------------------------------------------------
[wifi_para]
wifi_used = 0
wifi_sdc_id = 3
wifi_usbc_id = 2
wifi_usbc_type = 1
wifi_mod_sel = 7
wifi_power = ""
; 1 - bcm40181 sdio wifi gpio config
;bcm40181_shdn = port:PH09<1><default><default><0>
;bcm40181_host_wake = port:PH10<0><default><default><0>
; 2 - bcm40183 sdio wifi gpio config
;bcm40183_wl_regon = port:PH09<1><default><default><0>
;bcm40183_wl_host_wake = port:PH10<0><default><default><0>
;bcm40183_bt_rst = port:PB05<1><default><default><0>
;bcm40183_bt_regon = port:PB05<1><default><default><0>
;bcm40183_bt_wake = port:PI20<1><default><default><0>
;bcm40183_bt_host_wake = port:PI21<0><default><default><0>
; 3 - rtl8723as sdio wifi + bt gpio config
rtk_rtl8723as_wl_dis = port:PH09<1><default><default><0>
rtk_rtl8723as_bt_dis = port:PB05<1><default><default><0>
rtk_rtl8723as_wl_host_wake = port:PH10<0><default><default><0>
rtk_rtl8723as_bt_host_wake = port:PI21<0><default><default><0>
; 4 - rtl8189es sdio wifi gpio config
;rtl8189es_shdn = port:PH09<1><default><default><0>
;rtl8189es_wakeup = port:PH10<1><default><default><1>
; 5 - rtl8192cu usb wifi
; 6 - rtl8188eu usb wifi
; 7 - ap6210 sdio wifi + bt gpio config
ap6xxx_wl_regon = port:PH09<1><default><default><0>
ap6xxx_wl_host_wake = port:PH10<0><default><default><0>
ap6xxx_bt_regon = port:PB05<1><default><default><0>
ap6xxx_bt_wake = port:PI20<1><default><default><0>
ap6xxx_bt_host_wake = port:PI21<0><default><default><0>
;-------------------------------------------------------------------------------
;3G configuration
;-------------------------------------------------------------------------------
[3g_para]
3g_used = 0
3g_usbc_num = 2
3g_uart_num = 0
3g_pwr =
3g_wakeup =
3g_int =
;-------------------------------------------------------------------------------
;gyroscope
;-------------------------------------------------------------------------------
[gy_para]
gy_used = 0
gy_twi_id = 1
gy_twi_addr = 0x00
gy_int1 = port:PH18<6><1><default><default>
gy_int2 = port:PH19<6><1><default><default>
;-------------------------------------------------------------------------------
;light sensor
;-------------------------------------------------------------------------------
[ls_para]
ls_used = 0
ls_twi_id = 1
ls_twi_addr = 0x00
ls_int = port:PH20<6><1><default><default>
;-------------------------------------------------------------------------------
;compass
;-------------------------------------------------------------------------------
[compass_para]
compass_used = 0
compass_twi_id = 1
compass_twi_addr = 0x00
compass_int = port:PI13<6><1><default><default>
;-------------------------------------------------------------------------------
;blue tooth
;bt_used ---- blue tooth used (0- no used, 1- used)
;bt_uard_id ---- uart index
;-------------------------------------------------------------------------------
[bt_para]
bt_used = 1
bt_uart_id = 2
bt_wakeup = port:PH23<1><default><default><1>
bt_gpio =
bt_rst =
[i2s_para]
i2s_used = 0
i2s_channel = 2
i2s_mclk = port:PB5<2><1><default><default>
i2s_bclk = port:PB6<2><1><default><default>
i2s_lrclk = port:PB7<2><1><default><default>
i2s_dout0 = port:PB8<2><1><default><default>
i2s_dout1 =
i2s_dout2 =
i2s_dout3 =
i2s_din = port:PB12<2><1><default><default>
[spdif_para]
spdif_used = 0
spdif_mclk =
spdif_dout = port:PB13<4><1><default><default>
spdif_din =
[audio_para]
audio_used = 1
audio_pa_ctrl = port:PH15<1><default><default><0>
[switch_para]
switch_used=1
;-------------------------------------------------------------------------------
;ir --- infra remote configuration
;-------------------------------------------------------------------------------
[ir_para]
ir_used = 1
ir_rx = port:PB04<2><default><default><default>
;-------------------------------------------------------------------------------
;pmu_twi_addr ---slave address
;pmu_twi_id ---i2c bus number (0 TWI0, 1 TWI2, 2 TWI3)
;pmu_irq_id ---irq number (0 irq0,1 irq1,……)
;pmu_battery_rdc ---battery initial resistance,mΩ,根据实际电池内阻填写
;pmu_battery_cap ---battery capability,mAh,根据实际电池容量填写
;pmu_init_chgcur ---set initial charging current limite,mA,300/400/500/600/700/800/900/1000/1100/1200/1300/1400/1500/1600/1700/1800
;pmu_suspend_chgcur ---set suspend charging current limite,mA,300/400/500/600/700/800/900/1000/1100/1200/1300/1400/1500/1600/1700/1800
;pmu_resume_chgcur ---set resume charging current limite,mA,300/400/500/600/700/800/900/1000/1100/1200/1300/1400/1500/1600/1700/1800
;pmu_shutdown_chgcur ---set shutdown charging current limite,mA,300/400/500/600/700/800/900/1000/1100/1200/1300/1400/1500/1600/1700/1800
;pmu_init_chgvol ---set initial charing target voltage,mV,4100/4150/4200/4360
;pmu_init_chgend_rate ---set initial charing end current rate,10/15
;pmu_init_chg_enabled ---set initial charing enabled,0:关闭,1:打开
;pmu_init_adc_freq ---set initial adc frequency,Hz,25/50/100/200
;pmu_init_adc_freqc ---set initial coulomb adc coufrequency,Hz,25/50/100/200
;pmu_init_chg_pretime ---set initial pre-charging time,min,40/50/60/70
;pmu_init_chg_csttime ---set initial constance-charging time,min,360/480/600/720
;pmu_bat_para1 ---battery indication at 3.1328V
;pmu_bat_para2 ---battery indication at 3.2736V
;pmu_bat_para3 ---battery indication at 3.4144V
;pmu_bat_para4 ---battery indication at 3.5552V
;pmu_bat_para5 ---battery indication at 3.6256V
;pmu_bat_para6 ---battery indication at 3.6608V
;pmu_bat_para7 ---battery indication at 3.6960V
;pmu_bat_para8 ---battery indication at 3.7312V
;pmu_bat_para9 ---battery indication at 3.7664V
;pmu_bat_para10 ---battery indication at 3.8016V
;pmu_bat_para11 ---battery indication at 3.8368V
;pmu_bat_para12 ---battery indication at 3.8720V
;pmu_bat_para13 ---battery indication at 3.9424V
;pmu_bat_para14 ---battery indication at 4.0128V
;pmu_bat_para15 ---battery indication at 4.0832V
;pmu_bat_para16 ---battery indication at 4.1536V
;pmu_usbvol ---set usb-ac limited voltage level,mV,4000/4100/4200/4300/4400/4500/4600/4700,0 - not limite
;pmu_usbcur ---set usb-ac limited voltage level,mA,100/500/900, 0 - not limite
;pmu_usbvol_pc ---set usb-pc limited voltage level,mV,4000/4100/4200/4300/4400/4500/4600/4700,0 - not limite
;pmu_usbcur_pc ---set usb-pc limited voltage level,mA,100/500/900, 0 - not limite
;pmu_pwroff_vol ---set protect voltage when system start up,mV,2600/2700/2800/2900/3000/3100/3200/3300
;pmu_pwron_vol ---set protect voltage after system start up,mV,2600/2700/2800/2900/3000/3100/3200/3300
;pmu_pekoff_time ---set pek off time,ms, 4000/6000/8000/10000
;pmu_pekoff_en ---set pek off enable, 0:关闭,1:打开
;pmu_peklong_time ---set pek pek long irq time,ms,1000/1500/2000/2500
;pmu_pekon_time ---set pek on time,ms,128/1000/2000/3000
;pmu_pwrok_time ---set pmu pwrok delay time,ms,8/64
;pmu_pwrnoe_time ---set pmu n_oe power down delay time,ms,128/1000/2000/3000
;pmu_intotp_en ---set pmu power down when overtempertur enable,0:关闭,1:打开
;pmu_suspendpwroff_vol ---set pmu shutdown voltage when cpu is suspend and battery voltage is low
;pmu_batdeten ---set pmu battery detect enabled,0:关闭,1:打开
;-------------------------------------------------------------------------------
[pmu_para]
pmu_used = 1
pmu_twi_addr = 0x34
pmu_twi_id = 0
pmu_irq_id = 32
pmu_battery_rdc = 100
pmu_battery_cap = 2600
pmu_init_chgcur = 300
pmu_earlysuspend_chgcur = 600
pmu_suspend_chgcur = 1000
pmu_resume_chgcur = 300
pmu_shutdown_chgcur = 1000
pmu_init_chgvol = 4200
pmu_init_chgend_rate = 15
pmu_init_chg_enabled = 1
pmu_init_adc_freq = 100
pmu_init_adc_freqc = 100
pmu_init_chg_pretime = 50
pmu_init_chg_csttime = 720
pmu_bat_para1 = 0
pmu_bat_para2 = 0
pmu_bat_para3 = 0
pmu_bat_para4 = 0
pmu_bat_para5 = 5
pmu_bat_para6 = 8
pmu_bat_para7 = 11
pmu_bat_para8 = 22
pmu_bat_para9 = 33
pmu_bat_para10 = 43
pmu_bat_para11 = 50
pmu_bat_para12 = 59
pmu_bat_para13 = 71
pmu_bat_para14 = 83
pmu_bat_para15 = 92
pmu_bat_para16 = 100
pmu_usbvol_limit = 1
pmu_usbcur_limit = 0
pmu_usbvol = 4000
pmu_usbcur = 0
pmu_usbvol_pc = 4000
pmu_usbcur_pc = 0
pmu_pwroff_vol = 3300
pmu_pwron_vol = 2900
pmu_pekoff_time = 6000
pmu_pekoff_en = 1
pmu_peklong_time = 1500
pmu_pekon_time = 1000
pmu_pwrok_time = 64
pmu_pwrnoe_time = 2000
pmu_intotp_en = 1
pmu_used2 = 0
pmu_adpdet = port:PH02<0><default><default><default>
pmu_init_chgcur2 = 400
pmu_earlysuspend_chgcur2 = 600
pmu_suspend_chgcur2 = 1200
pmu_resume_chgcur2 = 400
pmu_shutdown_chgcur2 = 1200
pmu_suspendpwroff_vol = 3500
pmu_batdeten = 1
[recovery_key]
key_min =4
key_max =6
;----------------------------------------------------------------------------------
; dvfs voltage-frequency table configuration
;
; max_freq: cpu maximum frequency, based on Hz, can not be more than 1008MHz
; min_freq: cpu minimum frequency, based on Hz, can not be less than 60MHz
;
; LV_count: count of LV_freq/LV_volt, must be < 16
;
; LV1: core vdd is 1.45v if cpu frequency is (912Mhz, 1008Mhz]
; LV2: core vdd is 1.40v if cpu frequency is (864Mhz, 912Mhz]
; LV3: core vdd is 1.30v if cpu frequency is (720Mhz, 864Mhz]
; LV4: core vdd is 1.20v if cpu frequency is (528Mhz, 720Mhz]
; LV5: core vdd is 1.10v if cpu frequency is (312Mhz, 528Mhz]
; LV6: core vdd is 1.00v if cpu frequency is (144Mhz, 312Mhz]
; LV7: core vdd is 0.90v if cpu frequency is (60Mhz, 144Mhz]
;
;----------------------------------------------------------------------------------
[dvfs_table]
max_freq = 912000000
min_freq = 60000000
LV_count = 7
LV1_freq = 1008000000
LV1_volt = 1450
LV2_freq = 912000000
LV2_volt = 1400
LV3_freq = 864000000
LV3_volt = 1300
LV4_freq = 720000000
LV4_volt = 1200
LV5_freq = 528000000
LV5_volt = 1200
LV6_freq = 312000000
LV6_volt = 1200
LV7_freq = 144000000
LV7_volt = 1200
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment