crysxd/macros.cfg

## macros.cfg
## LDO recommended macros to get you started
# These macros are recommended by LDO
# You can copy these entries into your printer.cfg.
#
# Alternatively,
# You can copy these entries into your printer.cfg.
#


[gcode_macro M300]
description: Custom M300 code to allow beeper to be used in gcode
gcode:
    RESPOND PREFIX="BEEP"

[gcode_macro T0]
gcode:
    # Deactivate second extruder stepper
    SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=
    # Activate first extruder stepper
    SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
    SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=active_extruder VALUE=0

[gcode_macro T1]
gcode:
    # Deactivate first extruder stepper
    SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=
    # Activate second extruder stepper
    SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
    SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=active_extruder VALUE=1

[gcode_macro SET_PRESSURE_ADVANCE]
rename_existing: SET_PRESSURE_ADVANCE_BASE
variable_active_extruder: -1
gcode:
    {% set ADVANCE = params.ADVANCE|float %}
    {% set EXTRUDER = params.EXTRUDER|default("") %}
    {% set ACTIVE_EXTRUDER = printer["gcode_macro SET_PRESSURE_ADVANCE"].active_extruder %}

    {% if EXTRUDER == "" %}
      RESPOND PREFIX="Extruder not given, invering from active=" MSG={ACTIVE_EXTRUDER}
      {% if ACTIVE_EXTRUDER == 0 %}
         {% set EXTRUDER = "extruder" %}
      {% endif %}
      {% if ACTIVE_EXTRUDER == 1 %}
         {% set EXTRUDER = "extruder1" %}
      {% endif %}
    {% endif %}

    RESPOND PREFIX="Setting pressurece advance for" MSG={EXTRUDER}
    SET_PRESSURE_ADVANCE_BASE ADVANCE={ADVANCE} EXTRUDER={EXTRUDER}


[gcode_macro PAUSE]
rename_existing: PAUSE_BASE
gcode:
  G1 E-15 F4000
  PAUSE_BASE
  {% set park_z = printer.toolhead.axis_maximum.z|float - 20 %}
  {% set park_y = printer.toolhead.axis_maximum.y|float - 10 %}
  {% set park_x = printer.toolhead.axis_maximum.x|float / 2.0 %}
  G90
  G1 X{park_x} Y{park_y} Z{park_z} F8000

[gcode_macro RESUME]
rename_existing: RESUME_BASE
gcode:
  RESUME_BASE
  G1 E13 F4000

[gcode_macro G28]
rename_existing: G990028
gcode:
  {% set do_x = 0 %}
  {% set do_y = 0 %}
  {% set do_z = 0 %}

  {% if params.Y is defined %}
    ## for y home just y
    {% set do_y = 1 %}
  {% endif %}

  {% if params.X is defined %}
    ## for x home y first then X
    {% set do_x = 1 %}
  {% endif %}

  {% if params.Z is defined %}
    ## for z home all
    {% if "y" not in printer.toolhead.homed_axes %}
      {% set do_y = 1 %}
    {% endif %}
    {% if "x" not in printer.toolhead.homed_axes %}
      {% set do_x = 1 %}
    {% endif %}
    {% set do_z = 1 %}
  {% endif %}


  {% if do_y == 1 %}
    RESPOND PREFIX="info" MSG="Home > Todo: Y"
  {% endif %}
  {% if do_x == 1 %}
    RESPOND PREFIX="info" MSG="Home > Todo: X"
  {% endif %}
  {% if do_z == 1 %}
    RESPOND PREFIX="info" MSG="Home > Todo: Z"
  {% endif %}

  {% if do_x == 0 and do_y == 0 and do_z == 0 %}
    {% set do_x = 1 %}
    {% set do_y = 1 %}
    {% set do_z = 1 %}
    RESPOND PREFIX="info" MSG="Home > Doing all XYZ"
  {% endif %}

  {% if do_z == 1 %}
    {% set do_x = 1 %}
    {% set do_y = 1 %}
    RESPOND PREFIX="info" MSG="Home Z > Doing all XYZ"

    {% if "z" not in printer.toolhead.homed_axes %}
       SET_KINEMATIC_POSITION Z=0
    {% endif %}
    G91
    G1 Z5 F2000
  {% endif %}

  {% if do_y == 1 %}
    RESPOND PREFIX="info" MSG="Home > Y"
    G90
    G990028 Y0
    G91
    G0 Y5 F2000
    G90
  {% endif %}

  {% if do_x == 1 %}
    RESPOND PREFIX="info" MSG="Homing > X"
    G90
    G990028 X0
    G91
    G0 X5 F2000
    G90
  {% endif %}

  {% if do_z == 1 %}
    RESPOND PREFIX="info" MSG="Homing > Z"
    G90
    G0 X125 Y125 F12000
    G990028 Z0
    G91
    G0 Z20
    G90
  {% endif %}

  RESPOND PREFIX="info" MSG="Homing > Done"

[gcode_macro PRINT_START]
#   Use PRINT_START for the slicer starting script - please customize for your slicer of choice
# gcode:
    # CHOME                          ; home all axes if not done already
    # G90                            ; absolute positioning
    # G1 Z20 F3000                   ; move nozzle away from bed
    # G92 E0                         ; prime nozzle
    # G1 X2 Y1 Z0.28 F1500
    # G1 Y110 E20 F1500
    # G92 E0
gcode:
    LIGHT_PENDING
    {% set BED_TEMP = params.BED_TEMP|default(60)|float %}
    {% set EXTRUDER_TEMP = params.EXTRUDER_TEMP|default(190)|float %}
    {% set AREA_START = params.AREA_START|default("0,0") %}
    {% set AREA_END = params.AREA_END|default("200,200") %}
  	# Start TLM Start G-Code
	# Clear Display
	M117
	# Clear Existing Feedrate
	M220 S100
	# Clear Existing Flowrate
	M221 S100
    # Heat up Bed and extruder, do not wait
    M104 S150
	M140 S{BED_TEMP}
    # Home
	CHOME
	# Move to side and wait for final temps
    G1 X1 Y10 Z5 F4000
	M190 S{BED_TEMP}
    # Probe print area
    BED_MESH_CALIBRATE AREA_START={AREA_START} AREA_END={AREA_END}
	# Let's Print
	# Beep
	M300 S100 P1
	M300 S1000 P1
	# Relative Extruder
	M83
	# Set units to millimeters
	G21
	# Use absolute coordinates
	G90
	# Use absolute distances for extrusion
	M82
	# Fan Off
	M107
    {% if BED_TEMP > 90 %}
      FILTER_ON
    {% endif %}

	# Prime Blob disabled because I like doing skirts instead at the momemnt
    G1 X1 Y10 Z5 F4000
    M109 S{EXTRUDER_TEMP}
	NOZZLE_PURGE
    LIGHT_PRINTING

[gcode_macro PRINT_END]
#   Use PRINT_END for the slicer ending script - please customize for your slicer of choice
gcode:
    M400                           ; wait for buffer to clear
    G92 E0                         ; zero the extruder
    G1 E-4.0 F3600                 ; retract filament
    G91                            ; relative positioning

    #   Get Boundaries
    {% set max_x = printer.configfile.config["stepper_x"]["position_max"]|float %}
    {% set max_y = printer.configfile.config["stepper_y"]["position_max"]|float %}
    {% set max_z = printer.configfile.config["stepper_z"]["position_max"]|float %}

    #   Check end position to determine safe direction to move
    {% if printer.toolhead.position.x < (max_x - 20) %}
        {% set x_safe = 20.0 %}
    {% else %}
        {% set x_safe = -20.0 %}
    {% endif %}

    {% if printer.toolhead.position.y < (max_y - 20) %}
        {% set y_safe = 20.0 %}
    {% else %}
        {% set y_safe = -20.0 %}
    {% endif %}

    {% if printer.toolhead.position.z < (max_z - 20) %}
        {% set z_safe = 20.0 %}
    {% else %}
        {% set z_safe = max_z - printer.toolhead.position.z %}
    {% endif %}

    G0 Z{z_safe} F3600             ; move nozzle up
    G0 X{x_safe} Y{y_safe} F20000  ; move nozzle to remove stringing
    TURN_OFF_HEATERS
    M107                           ; turn off fan
    G90                            ; absolute positioning
    G0 X60 Y{max_y - 5} F3600      ; park nozzle at rear
    LIGHT_OFF
    FILTER_OFF

[gcode_macro FILTER_ON]
  gcode:
    SET_FAN_SPEED FAN=Nevermore SPEED=100

[gcode_macro FILTER_OFF]
  gcode:
    SET_FAN_SPEED FAN=Nevermore SPEED=0

[gcode_macro CHOME]
description: Homes XYZ axis only if printer is in a non-homed state
gcode:
  {% if "xyz" not in printer.toolhead.homed_axes %}
    G28
  {% endif %}

[gcode_macro UNLOAD_FILAMENT]
description: Unloads filament from toolhead
gcode:
  {% set EXTRUDER_TEMP = params.TEMP|default(230)|int %}
  CHOME
  G91                         ; relative positioning
  G1 Z20                      ; move nozzle upwards
  FRONT                       ; move the toolhead to the front
  LIGHT_PENDING
  M109 S{EXTRUDER_TEMP}       ; heat up the hotend
  LIGHT_PRINTING
  M83                         ; set extruder to relative mode
  G1 E-8 F1800                ; quickly retract a small amount to elimate stringing
  G4 P200                     ; pause for a short amount of time
  G1 E-50 F300                ; retract slowly the rest of the way
  G1 E-20 F300
  M400                        ; wait for moves to finish
  M117 Unload Complete!
  LIGHT_OFF

[gcode_macro LOAD_FILAMENT]
description: Loads new filament into toolhead
gcode:
  {% set EXTRUDER_TEMP = params.TEMP|default(230)|int %}
  FRONT                       ; move the toolhead to the front
  LIGHT_PENDING
  M109 S{EXTRUDER_TEMP}       ; heat up the hotend
  LIGHT_PRINTING
  M83                         ; set extruder to relative mode
  G1 E150 F300                 ; extrude slowlyL
  M400                        ; wait for moves to finish
  M117 Load Complete!
  LIGHT_OFF


[gcode_macro CENTER]
description: Moves the toolhead to the center
gcode:
  CHOME
  {% set x_center = printer.toolhead.axis_maximum.x|float / 2.0 %}
  {% set y_center = printer.toolhead.axis_maximum.y|float / 2.0 %}
  G90
  G1 X{x_center} Y{x_center} F7800

[gcode_macro FRONT]
description: Moves the toolhead to the front
gcode:
  CHOME
  {% set x_center = printer.toolhead.axis_maximum.x|float / 2.0 %}
  {% set y_center = printer.toolhead.axis_maximum.y|float / 2.0 %}
  G90
  G1 X{x_center} Y10 F7800

[gcode_macro BACK]
description: Moves the toolhead to the back
gcode:
  CHOME
  {% set x_center = printer.toolhead.axis_maximum.x|float / 2.0 %}
  {% set y_back = printer.toolhead.axis_maximum.y|float - 10 %}
  G90
  G1 X{x_center} Y{y_back} F7800

[gcode_macro NOZZLE_PURGE]
description: Draw a purge line at the front left edge of the build plate
gcode:
  CHOME
  G0 X2.5 Y4 F3000 ; Go to front
  G0 Z0.3 ; Drop to bed
  M83 ; Set extruder to relative mode
  G1 E25 F500 ;
  G1 X45 E15 F500 ; Extrude 25mm of filament in a 4cm line
  G1 E-0.5 F400 ; Retract a little
  G1 X85 F4000 ; Quickly wipe away from the filament line
  G1 Z0.8 ; Raise and begin printing.

[gcode_macro LIGHT_PENDING]
gcode:
  SET_LED LED=toolhead_light RED=1 GREEN=0.02 BLUE=0.02 WHITE=0
  SET_LED LED=underground_lights RED=1 GREEN=0.02 BLUE=0 WHITE=0
  SET_PIN PIN=bed_lights VALUE=0.2

[gcode_macro LIGHT_PRINTING]
gcode:
  SET_LED LED=toolhead_light RED=1 GREEN=0.3 BLUE=0 WHITE=0 INDEX=1 TRANSMIT=0
  SET_LED LED=toolhead_light RED=0 GREEN=0 BLUE=0 WHITE=1 INDEX=2 TRANSMIT=0
  SET_LED LED=toolhead_light RED=0 GREEN=0 BLUE=0 WHITE=1 INDEX=3
  SET_LED LED=underground_lights RED=1 GREEN=0.3 BLUE=0 WHITE=1
  SET_PIN PIN=bed_lights VALUE=1

[gcode_macro LIGHT_OFF]
gcode:
  SET_LED LED=toolhead_light RED=0 GREEN=0.02 BLUE=0 WHITE=0 INDEX=1 TRANSMIT=0
  SET_LED LED=toolhead_light RED=0 GREEN=0 BLUE=0 WHITE=0 INDEX=2 TRANSMIT=0
  SET_LED LED=toolhead_light RED=0 GREEN=0 BLUE=0 WHITE=0 INDEX=3
  SET_LED LED=underground_lights RED=0 GREEN=0 BLUE=0 WHITE=0
  SET_PIN PIN=bed_lights VALUE=0

[gcode_macro FAN_ON]
gcode:
  SET_FAN_SPEED FAN=hotend_fan SPEED=0.5
  SET_FAN_SPEED FAN=fan SPEED=0.5

[gcode_macro M600]
gcode:
  PAUSE
  FRONT
  UNLOAD_FILAMENT TEMP={ printer.extruder.target }


## printer.cfg
[include fluidd.cfg]
## *** THINGS TO CHANGE/CHECK: ***
## MCU paths                         	[mcu] section
## Thermistor types                      [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
## PID tune                              [extruder] and [heater_bed] sections
## Fine tune E steps                     [extruder] section

## For wiring directions please see https://docs.vorondesign.com/build/electrical/sw_miniE3_v20_wiring.html

## Webclient config files. Uncomment one depending on UI being used.
[include mainsail.cfg]
[include macros.cfg]
[include knomi.cfg]
#[include print_area_bed_mesh.cfg]
#[include shaper.cfg]
#[include fluidd.cfg]
[virtual_sdcard]
path: /home/pi/printer_data/gcodes
on_error_gcode: CANCEL_PRINT


[force_move]
enable_force_move: True

[gcode_arcs] # For OrcoSlicer
[exclude_object]

[printer]
kinematics: corexz
max_velocity: 300
max_accel: 3500
max_z_velocity: 50
max_z_accel: 1000
square_corner_velocity: 4.0

[mcu]
###Change to device found by "ls -l /dev/serial/by-id/" with just one this MCU connected to Pi
serial: /dev/serial/by-id/usb-Klipper_stm32g0b1xx_5000120012504B5735313920-if00

# [mcu v2]
# ###Change to device found by "ls -l /dev/serial/by-id/" with just one this MCU connected to Pi
# serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_39FFD1054247333127622257-if00

[mcu v1]
###Change to device found by "ls -l /dev/serial/by-id/" with just one this MCU connected to Pi
serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_36FFD7055252343511611743-if00

[mcu rpi]
serial: /tmp/klipper_host_mcu

[static_digital_output usb_pullup_enable]
pins: !PC13

#####################################################################
# 	X Stepper Settings
#####################################################################

######
# Motor -XM
# Endstop - X-STOP
###############
[stepper_x]
step_pin: v1:PB13
dir_pin: v1:PB12
enable_pin: !v1:PB14
rotation_distance: 40
full_steps_per_rotation: 200
microsteps: 32
endstop_pin: tmc2209_stepper_x:virtual_endstop
position_endstop: 0
position_min: 0
position_max: 225
homing_speed: 50
homing_positive_dir: false
homing_retract_dist: 0

[tmc2209 stepper_x]
uart_pin: v1:PB15
#tx_pin: v2:PC10
#uart_address: 1
run_current: 0.725 # Creality stock: 0.9A
interpolate: False
stealthchop_threshold: 999999
diag_pin: ^v1:PC0
driver_SGTHRS: 115 # tune this once it's working.

#####################################################################
#   Y Stepper Settings
#####################################################################

######
# Motor -YM
# Endstop - Y-STOP
###############
[stepper_y]
step_pin: PB10
dir_pin: !PB2
enable_pin: !PB11
rotation_distance: 40
full_steps_per_rotation: 200
microsteps: 32
## Ucomment one of the following:
## Switch-based endstop for Y
#endstop_pin: ^PC1
## Sensorless endstop for Y
endstop_pin: tmc2209_stepper_y:virtual_endstop
homing_retract_dist: 0 # Uncomment this line too
position_endstop: 0
position_min: 0
position_max: 235
homing_speed: 50
homing_positive_dir: false

[tmc2209 stepper_y]
uart_pin: PC11
tx_pin: PC10
uart_address: 2
run_current: 0.6 # Creality stock: 0.725A
interpolate: False
stealthchop_threshold: 999999
## Uncomment if using sensorless Y homing.
diag_pin: ^PC1
driver_SGTHRS: 110 # tune this once it's working.

#####################################################################
# 	Z Stepper Settings
#####################################################################

######
# Motor -ZAM
# Endstop - Z-STOP
###############
[stepper_z]
step_pin: v1:PB0
dir_pin: v1:PC5
enable_pin: !v1:PB1
rotation_distance: 40
full_steps_per_rotation: 200
microsteps: 32
endstop_pin: probe:z_virtual_endstop
position_max: 150
homing_speed: 25
position_min: -6.0

[tmc2209 stepper_z]
uart_pin: v1:PC10
# tx_pin: v2:PC10
# uart_address: 3
run_current: 0.725 # Creality stock: 0.9A
interpolate: False
stealthchop_threshold: 999999

#####################################################################
#   Extruder Settings
#####################################################################

######
#Motor - EM
###############
[extruder]
# E0_STEP_PIN        PB3
# E0_DIR_PIN         PB4
# E0_ENABLE_PIN      PB1
# E0_UART_RX         PC11
# E0_UART_TX         PC10
step_pin: v1:PB3 # 2n extruder: v1:PB10 #
dir_pin: !v1:PB4 # 2n extruder: v1:PB2
enable_pin: !v1:PD2 # 2n extruder: !v1:PB11
##  Update value below when you perform extruder calibration
##  If you ask for 100mm of filament, but in reality it is 98mm:
##  rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
##  22.6789511 is a good starting point
rotation_distance: 21.9897831339   #Bondtech 5mm Drive Gears
##  Update Gear Ratio depending on your Extruder Type
##  Use 50:10 for Stealthburner/Clockwork 2
##  Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
##  Use 80:20 for M4, M3.1
gear_ratio: 80:20
microsteps: 32
full_steps_per_rotation: 200
nozzle_diameter: 0.400
filament_diameter: 1.75
heater_pin: PC8
##  Validate the following thermistor type to make sure it is correct
##  See https://www.klipper3d.org/Config_Reference.html#common-thermistors for additional options
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA0
min_temp: 10
max_temp: 270
max_power: 1.0
max_extrude_cross_section: 10
min_extrude_temp:10# 170
#control = pid
#pid_kp = 26.213
#pid_ki = 1.304
#pid_kd = 131.721
#Set appropriate once tuning your printer
pressure_advance: 0.38
##	Default is 0.040, leave stock
# pressure_advance_smooth_time: 0.040
max_extrude_only_distance: 320.0

[tmc2209 extruder]
uart_pin: v1:PC11 # 2n extruder: v1:PC6
# tx_pin: PC10
#uart_address: 1
run_current: 0.55 # Creality stock: 0.725A
hold_current: 0.3
interpolate: False

[extruder_stepper extruder1]
extruder: extruder
step_pin:  v1:PB10
dir_pin: v1:PB2
enable_pin: !v1:PB11
gear_ratio: 80:20
rotation_distance: 21.9830515677   #Bondtech 5mm Drive Gears
microsteps: 32
pressure_advance: 0.38
full_steps_per_rotation: 200

[tmc2209 extruder_stepper extruder1]
uart_pin: v1:PC6
# tx_pin: PC10
#uart_address: 1
run_current: 0.55 # Creality stock: 0.725A
hold_current: 0.3
interpolate: False

#####################################################################
# 	Bed Heater
#####################################################################

######
# BED Connector
###############
[heater_bed]
heater_pin: PC9
##  Validate the following thermistor type to make sure it is correct
##  See https://www.klipper3d.org/Config_Reference.html#common-thermistors for additional options
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC4
min_temp: 0
max_temp: 130
#control: pid
#pid_kp: 58.437
#pid_ki: 2.347
#pid_kd: 363.769

#####################################################################
# 	Probe
#####################################################################

######
#Z Max Connector on Z(main) Board
#Inductive Probe
###############
[bltouch]
sensor_pin: ^PC2
control_pin: PA1
x_offset: 0
y_offset: -23
#z_offset: 1

#####################################################################
# 	Fan Control
#####################################################################

######
# Electronics Fan
# FAN1 Connector
###############
[controller_fan controller_fan]
pin: PC0
max_power: 1.00
kick_start_time: 0.25
heater: heater_bed
cycle_time: .08

######
# Hot End Fan
# FAN2 Connector
###############
[heater_fan extruder_fan]
pin: PB15
heater: extruder
heater_temp: 50.0
##  If you are experiencing back flow, you can reduce fan_speed
#fan_speed: 1.0

######
# Part Cooling Fan
# FAN0 Connector
###############
[fan]
pin: PC6  # "FAN0"
cycle_time: .09
##	Depending on your fan, you may need to increase this value
##	if your fan will not start. Can change cycle_time (increase)
##	if your fan is not able to slow down effectively
kick_start_time: .25

#####################################################################
#   Homing and Bed Mesh
#####################################################################
# [homing_override]
# axes: z
# set_position_z: 0
# gcode:
#     G90
#     G0 Z5 F1000
#     G28 X Y
#     G0 X125 Y125 F12000
#     G28 Z0
#     G0 Z5 F1000

[bed_mesh]
speed: 150
horizontal_move_z: 5
mesh_min: 10,-20
mesh_max: 215.0,170
probe_count: 5,5
algorithm: bicubic
fade_start: 1
fade_end: 10
fade_target: 0
horizontal_move_z: 10

#####################################################################
#   Case Lights
#####################################################################
# [output_pin LIGHTS]
# pin: PA8
# value: 0
# shutdown_value: 0

[neopixel toolhead_light]
pin: PA8
chain_count: 3
color_order: GRBW
initial_RED: 0
initial_GREEN: 0
initial_BLUE: 0
initial_WHITE: 0

[output_pin bed_lights]
pin: v1:PC8
pwm: True
hardware_pwm: True
cycle_time: 0.0001

[neopixel underground_lights]
pin: v1:PC7
chain_count: 17
color_order: GRB
initial_RED: 0
initial_GREEN: 0
initial_BLUE: 0
initial_WHITE: 0


[delayed_gcode _setup_after_boot]
initial_duration: 1
gcode:
  LIGHT_OFF
  BED_MESH_PROFILE LOAD=default
  T0

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bltouch]
#*# z_offset = 4.099
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 29.671
#*# pid_ki = 2.174
#*# pid_kd = 101.251
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 69.505
#*# pid_ki = 2.097
#*# pid_kd = 576.025
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 	  0.925000, 0.856250, 0.825000, 0.843750, 0.875000
#*# 	  0.600000, 0.575000, 0.537500, 0.550000, 0.600000
#*# 	  0.306250, 0.275000, 0.268750, 0.262500, 0.325000
#*# 	  0.050000, 0.018750, 0.012500, 0.025000, 0.125000
#*# 	  -0.181250, -0.231250, -0.225000, -0.200000, -0.125000
#*# x_count = 5
#*# y_count = 5
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = bicubic
#*# tension = 0.2
#*# min_x = 10.0
#*# max_x = 215.0
#*# min_y = -20.0
#*# max_y = 170.0
#*#
#*# [bed_mesh test]
#*# version = 1
#*# points =
#*# 	0.0, 0.087500, 0.121875, 0.190625
#*# 	0.0, 0.037500, 0.109375, 0.209375
#*# 	0, -0.012500, 0.071875, 0.221875
#*# 	0, -0.056250, 0.015625, 0.178125
#*# x_count = 4
#*# y_count = 4
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = bicubic
#*# tension = 0.2
#*# min_x = 10.0
#*# max_x = 214.99
#*# min_y = -20.0
#*# max_y = 169.99
#*#
#*# [input_shaper]
#*# shaper_type_y = ei
#*# shaper_freq_y = 43.4
#*# shaper_type_x = mzv
#*# shaper_freq_x = 49.0
	## LDO recommended macros to get you started
	# These macros are recommended by LDO
	# You can copy these entries into your printer.cfg.
	#
	# Alternatively,
	# You can copy these entries into your printer.cfg.
	#


	[gcode_macro M300]
	description: Custom M300 code to allow beeper to be used in gcode
	gcode:
	RESPOND PREFIX="BEEP"

	[gcode_macro T0]
	gcode:
	# Deactivate second extruder stepper
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=
	# Activate first extruder stepper
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=active_extruder VALUE=0

	[gcode_macro T1]
	gcode:
	# Deactivate first extruder stepper
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=
	# Activate second extruder stepper
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=active_extruder VALUE=1

	[gcode_macro SET_PRESSURE_ADVANCE]
	rename_existing: SET_PRESSURE_ADVANCE_BASE
	variable_active_extruder: -1
	gcode:
	{% set ADVANCE = params.ADVANCE\|float %}
	{% set EXTRUDER = params.EXTRUDER\|default("") %}
	{% set ACTIVE_EXTRUDER = printer["gcode_macro SET_PRESSURE_ADVANCE"].active_extruder %}

	{% if EXTRUDER == "" %}
	RESPOND PREFIX="Extruder not given, invering from active=" MSG={ACTIVE_EXTRUDER}
	{% if ACTIVE_EXTRUDER == 0 %}
	{% set EXTRUDER = "extruder" %}
	{% endif %}
	{% if ACTIVE_EXTRUDER == 1 %}
	{% set EXTRUDER = "extruder1" %}
	{% endif %}
	{% endif %}

	RESPOND PREFIX="Setting pressurece advance for" MSG={EXTRUDER}
	SET_PRESSURE_ADVANCE_BASE ADVANCE={ADVANCE} EXTRUDER={EXTRUDER}


	[gcode_macro PAUSE]
	rename_existing: PAUSE_BASE
	gcode:
	G1 E-15 F4000
	PAUSE_BASE
	{% set park_z = printer.toolhead.axis_maximum.z\|float - 20 %}
	{% set park_y = printer.toolhead.axis_maximum.y\|float - 10 %}
	{% set park_x = printer.toolhead.axis_maximum.x\|float / 2.0 %}
	G90
	G1 X{park_x} Y{park_y} Z{park_z} F8000

	[gcode_macro RESUME]
	rename_existing: RESUME_BASE
	gcode:
	RESUME_BASE
	G1 E13 F4000

	[gcode_macro G28]
	rename_existing: G990028
	gcode:
	{% set do_x = 0 %}
	{% set do_y = 0 %}
	{% set do_z = 0 %}

	{% if params.Y is defined %}
	## for y home just y
	{% set do_y = 1 %}
	{% endif %}

	{% if params.X is defined %}
	## for x home y first then X
	{% set do_x = 1 %}
	{% endif %}

	{% if params.Z is defined %}
	## for z home all
	{% if "y" not in printer.toolhead.homed_axes %}
	{% set do_y = 1 %}
	{% endif %}
	{% if "x" not in printer.toolhead.homed_axes %}
	{% set do_x = 1 %}
	{% endif %}
	{% set do_z = 1 %}
	{% endif %}


	{% if do_y == 1 %}
	RESPOND PREFIX="info" MSG="Home > Todo: Y"
	{% endif %}
	{% if do_x == 1 %}
	RESPOND PREFIX="info" MSG="Home > Todo: X"
	{% endif %}
	{% if do_z == 1 %}
	RESPOND PREFIX="info" MSG="Home > Todo: Z"
	{% endif %}

	{% if do_x == 0 and do_y == 0 and do_z == 0 %}
	{% set do_x = 1 %}
	{% set do_y = 1 %}
	{% set do_z = 1 %}
	RESPOND PREFIX="info" MSG="Home > Doing all XYZ"
	{% endif %}

	{% if do_z == 1 %}
	{% set do_x = 1 %}
	{% set do_y = 1 %}
	RESPOND PREFIX="info" MSG="Home Z > Doing all XYZ"

	{% if "z" not in printer.toolhead.homed_axes %}
	SET_KINEMATIC_POSITION Z=0
	{% endif %}
	G91
	G1 Z5 F2000
	{% endif %}

	{% if do_y == 1 %}
	RESPOND PREFIX="info" MSG="Home > Y"
	G90
	G990028 Y0
	G91
	G0 Y5 F2000
	G90
	{% endif %}

	{% if do_x == 1 %}
	RESPOND PREFIX="info" MSG="Homing > X"
	G90
	G990028 X0
	G91
	G0 X5 F2000
	G90
	{% endif %}

	{% if do_z == 1 %}
	RESPOND PREFIX="info" MSG="Homing > Z"
	G90
	G0 X125 Y125 F12000
	G990028 Z0
	G91
	G0 Z20
	G90
	{% endif %}

	RESPOND PREFIX="info" MSG="Homing > Done"

	[gcode_macro PRINT_START]
	# Use PRINT_START for the slicer starting script - please customize for your slicer of choice
	# gcode:
	# CHOME ; home all axes if not done already
	# G90 ; absolute positioning
	# G1 Z20 F3000 ; move nozzle away from bed
	# G92 E0 ; prime nozzle
	# G1 X2 Y1 Z0.28 F1500
	# G1 Y110 E20 F1500
	# G92 E0
	gcode:
	LIGHT_PENDING
	{% set BED_TEMP = params.BED_TEMP\|default(60)\|float %}
	{% set EXTRUDER_TEMP = params.EXTRUDER_TEMP\|default(190)\|float %}
	{% set AREA_START = params.AREA_START\|default("0,0") %}
	{% set AREA_END = params.AREA_END\|default("200,200") %}
	# Start TLM Start G-Code
	# Clear Display
	M117
	# Clear Existing Feedrate
	M220 S100
	# Clear Existing Flowrate
	M221 S100
	# Heat up Bed and extruder, do not wait
	M104 S150
	M140 S{BED_TEMP}
	# Home
	CHOME
	# Move to side and wait for final temps
	G1 X1 Y10 Z5 F4000
	M190 S{BED_TEMP}
	# Probe print area
	BED_MESH_CALIBRATE AREA_START={AREA_START} AREA_END={AREA_END}
	# Let's Print
	# Beep
	M300 S100 P1
	M300 S1000 P1
	# Relative Extruder
	M83
	# Set units to millimeters
	G21
	# Use absolute coordinates
	G90
	# Use absolute distances for extrusion
	M82
	# Fan Off
	M107
	{% if BED_TEMP > 90 %}
	FILTER_ON
	{% endif %}

	# Prime Blob disabled because I like doing skirts instead at the momemnt
	G1 X1 Y10 Z5 F4000
	M109 S{EXTRUDER_TEMP}
	NOZZLE_PURGE
	LIGHT_PRINTING

	[gcode_macro PRINT_END]
	# Use PRINT_END for the slicer ending script - please customize for your slicer of choice
	gcode:
	M400 ; wait for buffer to clear
	G92 E0 ; zero the extruder
	G1 E-4.0 F3600 ; retract filament
	G91 ; relative positioning

	# Get Boundaries
	{% set max_x = printer.configfile.config["stepper_x"]["position_max"]\|float %}
	{% set max_y = printer.configfile.config["stepper_y"]["position_max"]\|float %}
	{% set max_z = printer.configfile.config["stepper_z"]["position_max"]\|float %}

	# Check end position to determine safe direction to move
	{% if printer.toolhead.position.x < (max_x - 20) %}
	{% set x_safe = 20.0 %}
	{% else %}
	{% set x_safe = -20.0 %}
	{% endif %}

	{% if printer.toolhead.position.y < (max_y - 20) %}
	{% set y_safe = 20.0 %}
	{% else %}
	{% set y_safe = -20.0 %}
	{% endif %}

	{% if printer.toolhead.position.z < (max_z - 20) %}
	{% set z_safe = 20.0 %}
	{% else %}
	{% set z_safe = max_z - printer.toolhead.position.z %}
	{% endif %}

	G0 Z{z_safe} F3600 ; move nozzle up
	G0 X{x_safe} Y{y_safe} F20000 ; move nozzle to remove stringing
	TURN_OFF_HEATERS
	M107 ; turn off fan
	G90 ; absolute positioning
	G0 X60 Y{max_y - 5} F3600 ; park nozzle at rear
	LIGHT_OFF
	FILTER_OFF

	[gcode_macro FILTER_ON]
	gcode:
	SET_FAN_SPEED FAN=Nevermore SPEED=100

	[gcode_macro FILTER_OFF]
	gcode:
	SET_FAN_SPEED FAN=Nevermore SPEED=0

	[gcode_macro CHOME]
	description: Homes XYZ axis only if printer is in a non-homed state
	gcode:
	{% if "xyz" not in printer.toolhead.homed_axes %}
	G28
	{% endif %}

	[gcode_macro UNLOAD_FILAMENT]
	description: Unloads filament from toolhead
	gcode:
	{% set EXTRUDER_TEMP = params.TEMP\|default(230)\|int %}
	CHOME
	G91 ; relative positioning
	G1 Z20 ; move nozzle upwards
	FRONT ; move the toolhead to the front
	LIGHT_PENDING
	M109 S{EXTRUDER_TEMP} ; heat up the hotend
	LIGHT_PRINTING
	M83 ; set extruder to relative mode
	G1 E-8 F1800 ; quickly retract a small amount to elimate stringing
	G4 P200 ; pause for a short amount of time
	G1 E-50 F300 ; retract slowly the rest of the way
	G1 E-20 F300
	M400 ; wait for moves to finish
	M117 Unload Complete!
	LIGHT_OFF

	[gcode_macro LOAD_FILAMENT]
	description: Loads new filament into toolhead
	gcode:
	{% set EXTRUDER_TEMP = params.TEMP\|default(230)\|int %}
	FRONT ; move the toolhead to the front
	LIGHT_PENDING
	M109 S{EXTRUDER_TEMP} ; heat up the hotend
	LIGHT_PRINTING
	M83 ; set extruder to relative mode
	G1 E150 F300 ; extrude slowlyL
	M400 ; wait for moves to finish
	M117 Load Complete!
	LIGHT_OFF


	[gcode_macro CENTER]
	description: Moves the toolhead to the center
	gcode:
	CHOME
	{% set x_center = printer.toolhead.axis_maximum.x\|float / 2.0 %}
	{% set y_center = printer.toolhead.axis_maximum.y\|float / 2.0 %}
	G90
	G1 X{x_center} Y{x_center} F7800

	[gcode_macro FRONT]
	description: Moves the toolhead to the front
	gcode:
	CHOME
	{% set x_center = printer.toolhead.axis_maximum.x\|float / 2.0 %}
	{% set y_center = printer.toolhead.axis_maximum.y\|float / 2.0 %}
	G90
	G1 X{x_center} Y10 F7800

	[gcode_macro BACK]
	description: Moves the toolhead to the back
	gcode:
	CHOME
	{% set x_center = printer.toolhead.axis_maximum.x\|float / 2.0 %}
	{% set y_back = printer.toolhead.axis_maximum.y\|float - 10 %}
	G90
	G1 X{x_center} Y{y_back} F7800

	[gcode_macro NOZZLE_PURGE]
	description: Draw a purge line at the front left edge of the build plate
	gcode:
	CHOME
	G0 X2.5 Y4 F3000 ; Go to front
	G0 Z0.3 ; Drop to bed
	M83 ; Set extruder to relative mode
	G1 E25 F500 ;
	G1 X45 E15 F500 ; Extrude 25mm of filament in a 4cm line
	G1 E-0.5 F400 ; Retract a little
	G1 X85 F4000 ; Quickly wipe away from the filament line
	G1 Z0.8 ; Raise and begin printing.

	[gcode_macro LIGHT_PENDING]
	gcode:
	SET_LED LED=toolhead_light RED=1 GREEN=0.02 BLUE=0.02 WHITE=0
	SET_LED LED=underground_lights RED=1 GREEN=0.02 BLUE=0 WHITE=0
	SET_PIN PIN=bed_lights VALUE=0.2

	[gcode_macro LIGHT_PRINTING]
	gcode:
	SET_LED LED=toolhead_light RED=1 GREEN=0.3 BLUE=0 WHITE=0 INDEX=1 TRANSMIT=0
	SET_LED LED=toolhead_light RED=0 GREEN=0 BLUE=0 WHITE=1 INDEX=2 TRANSMIT=0
	SET_LED LED=toolhead_light RED=0 GREEN=0 BLUE=0 WHITE=1 INDEX=3
	SET_LED LED=underground_lights RED=1 GREEN=0.3 BLUE=0 WHITE=1
	SET_PIN PIN=bed_lights VALUE=1

	[gcode_macro LIGHT_OFF]
	gcode:
	SET_LED LED=toolhead_light RED=0 GREEN=0.02 BLUE=0 WHITE=0 INDEX=1 TRANSMIT=0
	SET_LED LED=toolhead_light RED=0 GREEN=0 BLUE=0 WHITE=0 INDEX=2 TRANSMIT=0
	SET_LED LED=toolhead_light RED=0 GREEN=0 BLUE=0 WHITE=0 INDEX=3
	SET_LED LED=underground_lights RED=0 GREEN=0 BLUE=0 WHITE=0
	SET_PIN PIN=bed_lights VALUE=0

	[gcode_macro FAN_ON]
	gcode:
	SET_FAN_SPEED FAN=hotend_fan SPEED=0.5
	SET_FAN_SPEED FAN=fan SPEED=0.5

	[gcode_macro M600]
	gcode:
	PAUSE
	FRONT
	UNLOAD_FILAMENT TEMP={ printer.extruder.target }
	[include fluidd.cfg]
	## * THINGS TO CHANGE/CHECK: *
	## MCU paths [mcu] section
	## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
	## PID tune [extruder] and [heater_bed] sections
	## Fine tune E steps [extruder] section

	## For wiring directions please see https://docs.vorondesign.com/build/electrical/sw_miniE3_v20_wiring.html

	## Webclient config files. Uncomment one depending on UI being used.
	[include mainsail.cfg]
	[include macros.cfg]
	[include knomi.cfg]
	#[include print_area_bed_mesh.cfg]
	#[include shaper.cfg]
	#[include fluidd.cfg]
	[virtual_sdcard]
	path: /home/pi/printer_data/gcodes
	on_error_gcode: CANCEL_PRINT


	[force_move]
	enable_force_move: True

	[gcode_arcs] # For OrcoSlicer
	[exclude_object]

	[printer]
	kinematics: corexz
	max_velocity: 300
	max_accel: 3500
	max_z_velocity: 50
	max_z_accel: 1000
	square_corner_velocity: 4.0

	[mcu]
	###Change to device found by "ls -l /dev/serial/by-id/" with just one this MCU connected to Pi
	serial: /dev/serial/by-id/usb-Klipper_stm32g0b1xx_5000120012504B5735313920-if00

	# [mcu v2]
	# ###Change to device found by "ls -l /dev/serial/by-id/" with just one this MCU connected to Pi
	# serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_39FFD1054247333127622257-if00

	[mcu v1]
	###Change to device found by "ls -l /dev/serial/by-id/" with just one this MCU connected to Pi
	serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_36FFD7055252343511611743-if00

	[mcu rpi]
	serial: /tmp/klipper_host_mcu

	[static_digital_output usb_pullup_enable]
	pins: !PC13

	#####################################################################
	# X Stepper Settings
	#####################################################################

	######
	# Motor -XM
	# Endstop - X-STOP
	###############
	[stepper_x]
	step_pin: v1:PB13
	dir_pin: v1:PB12
	enable_pin: !v1:PB14
	rotation_distance: 40
	full_steps_per_rotation: 200
	microsteps: 32
	endstop_pin: tmc2209_stepper_x:virtual_endstop
	position_endstop: 0
	position_min: 0
	position_max: 225
	homing_speed: 50
	homing_positive_dir: false
	homing_retract_dist: 0

	[tmc2209 stepper_x]
	uart_pin: v1:PB15
	#tx_pin: v2:PC10
	#uart_address: 1
	run_current: 0.725 # Creality stock: 0.9A
	interpolate: False
	stealthchop_threshold: 999999
	diag_pin: ^v1:PC0
	driver_SGTHRS: 115 # tune this once it's working.

	#####################################################################
	# Y Stepper Settings
	#####################################################################

	######
	# Motor -YM
	# Endstop - Y-STOP
	###############
	[stepper_y]
	step_pin: PB10
	dir_pin: !PB2
	enable_pin: !PB11
	rotation_distance: 40
	full_steps_per_rotation: 200
	microsteps: 32
	## Ucomment one of the following:
	## Switch-based endstop for Y
	#endstop_pin: ^PC1
	## Sensorless endstop for Y
	endstop_pin: tmc2209_stepper_y:virtual_endstop
	homing_retract_dist: 0 # Uncomment this line too
	position_endstop: 0
	position_min: 0
	position_max: 235
	homing_speed: 50
	homing_positive_dir: false

	[tmc2209 stepper_y]
	uart_pin: PC11
	tx_pin: PC10
	uart_address: 2
	run_current: 0.6 # Creality stock: 0.725A
	interpolate: False
	stealthchop_threshold: 999999
	## Uncomment if using sensorless Y homing.
	diag_pin: ^PC1
	driver_SGTHRS: 110 # tune this once it's working.

	#####################################################################
	# Z Stepper Settings
	#####################################################################

	######
	# Motor -ZAM
	# Endstop - Z-STOP
	###############
	[stepper_z]
	step_pin: v1:PB0
	dir_pin: v1:PC5
	enable_pin: !v1:PB1
	rotation_distance: 40
	full_steps_per_rotation: 200
	microsteps: 32
	endstop_pin: probe:z_virtual_endstop
	position_max: 150
	homing_speed: 25
	position_min: -6.0

	[tmc2209 stepper_z]
	uart_pin: v1:PC10
	# tx_pin: v2:PC10
	# uart_address: 3
	run_current: 0.725 # Creality stock: 0.9A
	interpolate: False
	stealthchop_threshold: 999999

	#####################################################################
	# Extruder Settings
	#####################################################################

	######
	#Motor - EM
	###############
	[extruder]
	# E0_STEP_PIN PB3
	# E0_DIR_PIN PB4
	# E0_ENABLE_PIN PB1
	# E0_UART_RX PC11
	# E0_UART_TX PC10
	step_pin: v1:PB3 # 2n extruder: v1:PB10 #
	dir_pin: !v1:PB4 # 2n extruder: v1:PB2
	enable_pin: !v1:PD2 # 2n extruder: !v1:PB11
	## Update value below when you perform extruder calibration
	## If you ask for 100mm of filament, but in reality it is 98mm:
	## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
	## 22.6789511 is a good starting point
	rotation_distance: 21.9897831339 #Bondtech 5mm Drive Gears
	## Update Gear Ratio depending on your Extruder Type
	## Use 50:10 for Stealthburner/Clockwork 2
	## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
	## Use 80:20 for M4, M3.1
	gear_ratio: 80:20
	microsteps: 32
	full_steps_per_rotation: 200
	nozzle_diameter: 0.400
	filament_diameter: 1.75
	heater_pin: PC8
	## Validate the following thermistor type to make sure it is correct
	## See https://www.klipper3d.org/Config_Reference.html#common-thermistors for additional options
	sensor_type: EPCOS 100K B57560G104F
	sensor_pin: PA0
	min_temp: 10
	max_temp: 270
	max_power: 1.0
	max_extrude_cross_section: 10
	min_extrude_temp:10# 170
	#control = pid
	#pid_kp = 26.213
	#pid_ki = 1.304
	#pid_kd = 131.721
	#Set appropriate once tuning your printer
	pressure_advance: 0.38
	## Default is 0.040, leave stock
	# pressure_advance_smooth_time: 0.040
	max_extrude_only_distance: 320.0

	[tmc2209 extruder]
	uart_pin: v1:PC11 # 2n extruder: v1:PC6
	# tx_pin: PC10
	#uart_address: 1
	run_current: 0.55 # Creality stock: 0.725A
	hold_current: 0.3
	interpolate: False

	[extruder_stepper extruder1]
	extruder: extruder
	step_pin: v1:PB10
	dir_pin: v1:PB2
	enable_pin: !v1:PB11
	gear_ratio: 80:20
	rotation_distance: 21.9830515677 #Bondtech 5mm Drive Gears
	microsteps: 32
	pressure_advance: 0.38
	full_steps_per_rotation: 200

	[tmc2209 extruder_stepper extruder1]
	uart_pin: v1:PC6
	# tx_pin: PC10
	#uart_address: 1
	run_current: 0.55 # Creality stock: 0.725A
	hold_current: 0.3
	interpolate: False

	#####################################################################
	# Bed Heater
	#####################################################################

	######
	# BED Connector
	###############
	[heater_bed]
	heater_pin: PC9
	## Validate the following thermistor type to make sure it is correct
	## See https://www.klipper3d.org/Config_Reference.html#common-thermistors for additional options
	sensor_type: EPCOS 100K B57560G104F
	sensor_pin: PC4
	min_temp: 0
	max_temp: 130
	#control: pid
	#pid_kp: 58.437
	#pid_ki: 2.347
	#pid_kd: 363.769

	#####################################################################
	# Probe
	#####################################################################

	######
	#Z Max Connector on Z(main) Board
	#Inductive Probe
	###############
	[bltouch]
	sensor_pin: ^PC2
	control_pin: PA1
	x_offset: 0
	y_offset: -23
	#z_offset: 1

	#####################################################################
	# Fan Control
	#####################################################################

	######
	# Electronics Fan
	# FAN1 Connector
	###############
	[controller_fan controller_fan]
	pin: PC0
	max_power: 1.00
	kick_start_time: 0.25
	heater: heater_bed
	cycle_time: .08

	######
	# Hot End Fan
	# FAN2 Connector
	###############
	[heater_fan extruder_fan]
	pin: PB15
	heater: extruder
	heater_temp: 50.0
	## If you are experiencing back flow, you can reduce fan_speed
	#fan_speed: 1.0

	######
	# Part Cooling Fan
	# FAN0 Connector
	###############
	[fan]
	pin: PC6 # "FAN0"
	cycle_time: .09
	## Depending on your fan, you may need to increase this value
	## if your fan will not start. Can change cycle_time (increase)
	## if your fan is not able to slow down effectively
	kick_start_time: .25

	#####################################################################
	# Homing and Bed Mesh
	#####################################################################
	# [homing_override]
	# axes: z
	# set_position_z: 0
	# gcode:
	# G90
	# G0 Z5 F1000
	# G28 X Y
	# G0 X125 Y125 F12000
	# G28 Z0
	# G0 Z5 F1000

	[bed_mesh]
	speed: 150
	horizontal_move_z: 5
	mesh_min: 10,-20
	mesh_max: 215.0,170
	probe_count: 5,5
	algorithm: bicubic
	fade_start: 1
	fade_end: 10
	fade_target: 0
	horizontal_move_z: 10

	#####################################################################
	# Case Lights
	#####################################################################
	# [output_pin LIGHTS]
	# pin: PA8
	# value: 0
	# shutdown_value: 0

	[neopixel toolhead_light]
	pin: PA8
	chain_count: 3
	color_order: GRBW
	initial_RED: 0
	initial_GREEN: 0
	initial_BLUE: 0
	initial_WHITE: 0

	[output_pin bed_lights]
	pin: v1:PC8
	pwm: True
	hardware_pwm: True
	cycle_time: 0.0001

	[neopixel underground_lights]
	pin: v1:PC7
	chain_count: 17
	color_order: GRB
	initial_RED: 0
	initial_GREEN: 0
	initial_BLUE: 0
	initial_WHITE: 0


	[delayed_gcode _setup_after_boot]
	initial_duration: 1
	gcode:
	LIGHT_OFF
	BED_MESH_PROFILE LOAD=default
	T0

	#*# <---------------------- SAVE_CONFIG ---------------------->
	#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
	#*#
	#*# [bltouch]
	#*# z_offset = 4.099
	#*#
	#*# [extruder]
	#*# control = pid
	#*# pid_kp = 29.671
	#*# pid_ki = 2.174
	#*# pid_kd = 101.251
	#*#
	#*# [heater_bed]
	#*# control = pid
	#*# pid_kp = 69.505
	#*# pid_ki = 2.097
	#*# pid_kd = 576.025
	#*#
	#*# [bed_mesh default]
	#*# version = 1
	#*# points =
	#*# 0.925000, 0.856250, 0.825000, 0.843750, 0.875000
	#*# 0.600000, 0.575000, 0.537500, 0.550000, 0.600000
	#*# 0.306250, 0.275000, 0.268750, 0.262500, 0.325000
	#*# 0.050000, 0.018750, 0.012500, 0.025000, 0.125000
	#*# -0.181250, -0.231250, -0.225000, -0.200000, -0.125000
	#*# x_count = 5
	#*# y_count = 5
	#*# mesh_x_pps = 2
	#*# mesh_y_pps = 2
	#*# algo = bicubic
	#*# tension = 0.2
	#*# min_x = 10.0
	#*# max_x = 215.0
	#*# min_y = -20.0
	#*# max_y = 170.0
	#*#
	#*# [bed_mesh test]
	#*# version = 1
	#*# points =
	#*# 0.0, 0.087500, 0.121875, 0.190625
	#*# 0.0, 0.037500, 0.109375, 0.209375
	#*# 0, -0.012500, 0.071875, 0.221875
	#*# 0, -0.056250, 0.015625, 0.178125
	#*# x_count = 4
	#*# y_count = 4
	#*# mesh_x_pps = 2
	#*# mesh_y_pps = 2
	#*# algo = bicubic
	#*# tension = 0.2
	#*# min_x = 10.0
	#*# max_x = 214.99
	#*# min_y = -20.0
	#*# max_y = 169.99
	#*#
	#*# [input_shaper]
	#*# shaper_type_y = ei
	#*# shaper_freq_y = 43.4
	#*# shaper_type_x = mzv
	#*# shaper_freq_x = 49.0