Skip to content

Instantly share code, notes, and snippets.

@nerdalert
Last active May 9, 2022 02:21
Show Gist options
  • Save nerdalert/28168b016112b7c13040 to your computer and use it in GitHub Desktop.
Save nerdalert/28168b016112b7c13040 to your computer and use it in GitHub Desktop.

Macvlan, Ipvlan and 802.1q Trunk Native Docker Support Notes

Contents

The PR can be found at: moby/libnetwork#964. This branch contains both macvlan and ipvlan as the mechanics are structure are very similar. These two drivers do not use bridges, e.g. docker0. Nor is there any NAT/PAT. All addresses are placed directly onto the wire via the --parent= interface.

NOTE: when you start containers on both Macvlan and Ipvlan networks the container CAN NOT ping or communicate with any interface on the Docker host. This is how Ipvlan and Macvlan Linux interfaces are designed. It is to isolate the default namespace/underlying OS from the containers running in namespaces. You can communicate with other containers as described in each section or anything external to the Docker host, just not the Docker host itself.

  • The driver caches NetworkCreate callbacks to the boltdb datastore along with populating *networks. In the case of a restart, the driver initializes the datastore with Init() and populates *networks since NetworkCreate() is only called once.

  • There can only be one (ipvlan or macvlan) driver type bound to a host interface with running containers at any given time. Currently the driver does not prevent ipvlan and macvlan networks to be created with the same --host_interface but will throw an error if you try to start an ipvlan container and a macvlan container at the same time on the same --host_interface. A mix of host interfaces and macvlan/ipvlan types can be used with running containers, each interface just needs to use the same type. Example: Macvlan Bridge or IPVlan L2. There is no mixing of running containers on the same host interface.

  • The specified gateway is external to the host or at least not defined by the driver itself.

  • Each network is isolated from one another. Any container inside the network/subnet can talk to one another without a reachable gateway in both macvlan bridge mode and ipvlan L2 mode. IP tables may be able to work around that if a user wanted to.

  • Containers on separate networks cannot reach one another without an external process routing between the two networks/subnets.

  • Note: In both Macvlan and Ipvlan you are not able to ping or communicate with the default namespace IP address. For example, if you create a container and try to ping the Docker host's eth0 it will not work. That traffic is explicitly filtered by the kernel modules themselves to offer additional provider isolation and security.

  • More information about Ipvlan & Macvlan can be found in the upstream readme

  • For a list of manual tests you can paste in and give a whirl see: macvlan_ipvlan_docker_driver_manual_tests.txt

Download the Binary

docker -v
Docker version 1.11.0-dev, build ac9d1b7-unsupported

MacVlan Bridge Mode Example Usage

  • In this example, eth0 on the docker host has an IP on the 192.168.1.0/24 network and a default gateway of 192.168.1.1. The gateway is an external router with an address of 192.168.1.1. An IP address is not required on the Docker host interface eth0 in bridge mode, it merely needs to be on the proper upstream network to get forwarded by a network switch or network router.

Note For Macvlan bridge mode and Ipvlan L2 mode the subnet values need to match the NIC's interface of the Docker host. For example, Use the same subnet and gateway of the Docker host ethernet interface that is specified by the -o host_iface= option.

  • The parent interface used in this example is eth0 and it is on the subnet 192.168.1.0/24. The containers in the docker network will also need to be on this same subnet as the parent --host_iface=. The gateway is an external router on the network, not any ip masquerading or any other local proxy (see diagrams for topologies).

-The parent interface -o host_iface=eth0 is configured as followed:

  • The driver is specified with -d driver_name option. In this case -d macvlan
ip addr show eth0
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    inet 192.168.1.251/24 brd 192.168.1.255 scope global eth0

Create the macvlan network and run a container attaching to it:

# Macvlan  (--macvlan_mode= Defaults to Bridge mode if not specified)
docker network  create  -d macvlan \
  --subnet=192.168.1.0/24 \
  --gateway=192.168.1.1 \
  -o host_iface=eth0 macnet100

# Start a container on the new network
docker  run --net=macnet100 -it --rm busybox

You can explicitly specify the bridge mode option -o macvlan_mode=bridge. It is the default so will be in bridge mode either way.

Ipvlan L2 Mode Example Usage

The ipvlan L2 mode example is virtually identical to the macvlan bridge mode example. The driver is specified with -d driver_name option. In this case -d ipvlan

The parent interface -o host_iface=eth0 is configured as followed:

ip addr show eth0
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    inet 192.168.1.251/24 brd 192.168.1.255 scope global eth0

Create the ipvlan network and run a container attaching to it:

# Ipvlan  (--ipvlan_mode= Defaults to L2 mode if not specified)
docker network  create -d ipvlan \
  --subnet=192.168.1.0/24 \
  --gateway=192.168.1.1 \
  -o host_iface=eth0 ipnet100

# Start a container on the new network
docker  run --net=ipnet100 -it --rm busybox

You can explicitly specify the l2 mode option -o ipvlan_mode=l2. It is the default so will be in l2 mode either way.

Macvlan 802.1q Trunk Bridge Mode Example Usage

Start two containers to test a ping. The default namespace is not reachable per macvlan design in order to isolate container namespaces from the underlying host.

The Linux sub-interface tagged with a vlan can either already exist or will be created when you call a docker network create. docker network rm will delete the sub-interface. Parent interfaces such as eth0 are not deleted, only sub-interface with a netlink parent index > 0.

For the driver to add/delete the vlan sub-interface the format needs to be interface_name.vlan_tag.

For example: eth0.50 denotes a parent interface of eth0 with a slave of eth0.50 tagged with vlan id 50. The equivalent ip link command would be ip link add link eth0 name eth0.50 type vlan id 50.

Replace the macvlan with ipvlan in the -d driver argument to create macvlan 802.1q trunks.

Vlan ID 50

In the first network tagged and isolated by the Docker host, eth0.50 is the parent interface tagged with vlan id 50 specified with -o host_iface=eth0.50. Other naming formats can be used, but the links need to be added and deleted manually using ip link or Linux configuration files. As long as the --host_iface exists anything can be used if compliant with Linux netlink.

# now add networks and hosts as you would normally by attaching to the master (sub)interface that is tagged
docker network  create  -d macvlan \
  --subnet=192.168.50.0/24 \
  --gateway=192.168.50.1 \
  -o host_iface=eth0.50 macvlan50

# in two separate terminals, start a Docker container and the containers can now ping one another.
docker run --net=macvlan50 -it --name macvlan_test5 --rm busybox
docker run --net=macvlan50 -it --name macvlan_test6 --rm busybox

Vlan ID 60

In the second network, tagged and isolated by the Docker host, eth0.60 is the parent interface tagged with vlan id 60 specified with -o host_iface=eth0.60. The macvlan_mode= defaults to macvlan_mode=bridge. It can also be explicitly set with the same result as shown in the next example.

# now add networks and hosts as you would normally by attaching to the master (sub)interface that is tagged. 
docker network  create  -d macvlan  --subnet=192.168.60.0/24 --gateway=192.168.60.1 -o host_iface=eth0.60 -o --macvlan_mode=bridge macvlan60

# in two separate terminals, start a Docker container and the containers can now ping one another.
docker run --net=macvlan60 -it --name macvlan_test7 --rm ubuntu
docker run --net=macvlan60 -it --name macvlan_test8 --rm ubuntu

Ipvlan 802.1q Trunk L2 Mode Example Usage

Architecturally, Ipvlan L2 mode trunking is the same as Macvlan with regard to gateways and L2 path isolation. There are nuances that can be advantageous for CAM table exhaustion in ToR switches, one MAC per port and MAC exhaustion on a host's parent NIC to name a few.

The Linux sub-interface tagged with a vlan can either already exist or will be created when you call a docker network create. docker network rm will delete the sub-interface. Parent interfaces such as eth0 are not deleted, only sub-interface with a netlink parent index > 0.

For the driver to add/delete the vlan sub-interface the format needs to be interface_name.vlan_tag. Other sub-interface naming can be used as the specified parent, but the link will not be deleted automatically when docker network rm is invoked.

The option to use either existing parent vlan sub-interface or let Docker manage them enables the user to either completely manage the Linux interfaces and networking or let Docker create and delete the Vlan parent sub-interface (netlink ip link) with no effort from the user.

For example: eth0.10 or eth0:10 to denote a sub-interface of eth0 tagged with vlan id 10. The equivalent ip link command would be ip link add link eth0 name eth0.10 type vlan id 10.

The example creates the vlan tagged networks and then start two containers to test connectivity between containers. Different VLANs cannot ping one another without a router routing between the two networks. The default namespace is not reachable per ipvlan design in order to isolate container namespaces from the underlying host.

Vlan ID 20

In the first network tagged and isolated by the Docker host, eth0.20 is the parent interface tagged with vlan id 20 specified with -o host_iface=eth0.20. Other naming formats can be used, but the links need to be added and deleted manually using ip link or Linux configuration files. As long as the --host_iface exists anything can be used if compliant with Linux netlink.

# now add networks and hosts as you would normally by attaching to the master (sub)interface that is tagged
docker network  create  -d ipvlan \
  --subnet=192.168.20.0/24 \
  --gateway=192.168.20.1 \
  -o host_iface=eth0.20 ipvlan20

# in two separate terminals, start a Docker container and the containers can now ping one another.
docker run --net=ipvlan20 -it --name ivlan_test1 --rm busybox
docker run --net=ipvlan20 -it --name ivlan_test2 --rm busybox

Vlan ID 30

In the second network, tagged and isolated by the Docker host, eth0.30 is the parent interface tagged with vlan id 30 specified with -o host_iface=eth0.30. The ipvlan_mode= defaults to l2 mode ipvlan_mode=l2. It can also be explicitly set with the same result as shown in the next example.

# now add networks and hosts as you would normally by attaching to the master (sub)interface that is tagged. 
docker network  create  -d ipvlan  \
  --subnet=192.168.30.0/24 \
  --gateway=192.168.30.1 \
  -o host_iface=eth0.30 \
  --ipvlan_mode=l2 ipvlan30

# in two separate terminals, start a Docker container and the containers can now ping one another.
docker run --net=ipvlan30 -it --name ivlan_test3 --rm ubuntu
docker run --net=ipvlan30 -it --name ivlan_test4 --rm ubuntu

The gateway is set inside of the container as the default gateway. That gateway would typically be an external router on the network.

$ ip route
default via 192.168.30.1 dev eth0
192.168.30.0/24 dev eth0  src 192.168.30.2

IPVlan L3 Mode Example Usage

-Ipvlan L3 mode drops all broadcast and multicast traffic. -L3 mode needs to be on a separate subnet as the default namespace since it requires a netlink route in the default namespace pointing to the Ipvlan parent interface.

  • The parent interface used in this example is eth0 and it is on the subnet 192.168.1.0/24. Notice the docker network is not on the same subnet as eth0.
  • Unlike macvlan bridge mode and ipvlan l2 modes, different subnets/networks can ping one another as long as they share the same parent interface --host_interface=.
ip a show eth0
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether 00:50:56:39:45:2e brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.251/24 brd 192.168.1.255 scope global eth0

-A traditional gateway doesn't mean much to an L3 mode Ipvlan interface since there is no broadcast traffic allowed. Because of this we simply point the the containers eth0 device as the default gateway. See below for CLI output of ip route from inside an L3 container.

The mode -o ipvlan_mode=l3 must be explicitly specified since the default ipvlan mode is l2.

# Create the Ipvlan L3 network
docker network  create -d ipvlan \
  --subnet=192.168.120.0/24 \
  -o host_iface=eth0 \
  -o ipvlan_mode=l3 ipvlan120

# Start a couple of containers
docker run --net=ipvlan120 -it --rm busybox 

# Or specify a specific IPv4 address
docker run --net=ipvlan120 --ip=192.168.120.10 -it --rm busybox 

You will notice there is no --gateway= option in the network create. The field is ignored if one is specified since it doesn't have a use in l3 mode. Take a look at the container routing table from inside of the container:

# Inside the container
$ ip route
default dev eth0
192.168.120.0/24 dev eth0  src 192.168.120.2

-Example: This route is added to the Docker host not the Docker container. eth0 in the route has to be the same interface as specified in the -o host_iface=eth0 network create.

In order to ping the container from a remote host or the container be able to ping a remote host, the remote host needs to have a route pointing to the host IP address of the container's Docker host eth interface.

-If you have two hosts and one of them has a ipvlan l3 mode container running, the second host needs to have a route added to ping the container. The following are the addresses of the example of two hosts, host1 running docker with a container in ipvlan l3 mode and host2 a regular host we will be pinging from the container and vice versa:

-Host1: Docker Host eth0: 192.168.1.249/24 -Host1: Docker ipvlan l3 mode container network: 192.168.130.0/24 -Host1: Docker ipvlan l3 mode container IP: 192.168.130.2 -Host2: Remote Host eth0: 192.168.1.251/24

First, add a route to the remote host that tells the host, in order to reach the container network 192.168.130.0/24 on Host1 use the next hop Host1 eth0 192.168.1.249. By adding the following route to

# On Host2 add a route for the L3 container network to be reached via the Docker host eth0 address (192.168.1.249).
ip route add 192.168.130.0/24 via 192.168.1.249

After adding the above route to Host1 it should be able to ping the L3 mode container at 192.168.130.2 from its eth0 interface with the IP 192.168.1.251 as should the container be able to ping 192.168.1.249 from its address at 192.168.130.2.

L3 (layer 3) or ip routing has the ability to scale well beyond L2 (layer 2) networks. The Internet is made up of a collection of interconnected L3 networks. This is attractive when coupled with the density presented by migrations to Docker containers and worth spending some time to understand if new to scaling networks.

IPv6

  • Default to dual stack? Currently does with generic v4 and gateway services. If ipv4 is not specified should we disable gateway services and provision v6 only etc.
  • Should EnableIPv6 be used?

Example: start two containers and ping one another:

# Create a v6 network
docker network create -d macvlan \
  --subnet=fe90::/64 \
  --gateway=fe90::22 \
  -o host_iface=eth0 macnetv6

# Start a container on the network
docker run --net=macnetv6 -it --rm busybox

View the container eth0 interface:

# IP config of the container once it starts:

$ ip addr show eth0
eth0@if3: <BROADCAST,MULTICAST,UP,LOWER_UP,M-DOWN> mtu 1500 qdisc noqueue
    link/ether ce:26:6b:b8:27:11 brd ff:ff:ff:ff:ff:ff
    inet 172.19.0.2/16 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 fe80::cc26:6bff:feb8:2711/64 scope link tentative
       valid_lft forever preferred_lft forever
    inet6 fe90::1/64 scope link flags 02
       valid_lft forever preferred_lft forever

Start a second container and ping the first containers v6 address at fe90::1 from it's address of fe90::2.

$ ip a show eth0
48: eth0@if2: <BROADCAST,MULTICAST,UP,LOWER_UP,M-DOWN> mtu 1500 qdisc noqueue
    link/ether 06:09:43:a2:91:c3 brd ff:ff:ff:ff:ff:ff
    inet 172.19.0.3/16 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 fe80::409:43ff:fea2:91c3/64 scope link
       valid_lft forever preferred_lft forever
    inet6 fe90::2/64 scope link flags 02
       valid_lft forever preferred_lft forever

$ ping -6 fe90::1
PING fe90::2 (fe90::1): 56 data bytes
64 bytes from fe90::1: seq=0 ttl=64 time=0.044 ms

Dummy Interface Default and Internal Network

One of the most important parameters a user passes for functionality is the -o parent= interface. In order to have functionality in all cases even if missing the parent interface is if the parent link is not passed, a dummy Linux interface will be setup. The dummy parent link is named with the first 12 numbers in the network ID.

Important Note: This configuration can also be setup using the Libnetwork --internal flag. The ONLY things a container on a dummy or internal network can communicate with is other containers on the docker network (containers that share the same --parent link).

Example: No parent interface specified - will default to creating a new Dummy interface for any container on that network. There is no way for those containers on that network to talk to anything other then eachother as they are completely isolated.

# Create v4 dummy network 
docker network create -d macvlan --subnet=192.168.242.0/24  macnet242
  
# Start two containers and verify they can ping one another
docker run --net=macnet242 -itd  alpine /bin/sh
docker run --net=macnet242 -itd  alpine /bin/sh

Will acheive the same results as using the --internal flag:

# Create v4 dummy network
docker network create -d macvlan --subnet=192.168.246.0/24 macnet242
  
# Start two containers and verify they can ping one another
docker run --net=macnet246 -itd  alpine /bin/sh
docker run --net=macnet246 -itd  alpine /bin/sh

All of the same options can be used with no --parent=eth0 specified ot --internal

docker network create -d macvlan  \
  --subnet=192.168.222.0/24 --subnet=192.168.224.0/24  \
  --subnet=fd18::/64  \
  --aux-address="exclude1=fd18::2" \
  --aux-address="exclude2=192.168.222.2" \
  --aux-address="exclude3=192.168.224.2" \
  --ip-range=192.168.222.0/25 \
  --ip-range=192.168.224.0/25 \
  -o macvlan_mode=bridge macnet222

  # Start containers on the network
  docker run --net=macnet222 -itd alpine /bin/sh
  docker run --net=macnet222 --ip=192.168.222.10 --ip6=fd18::10 -itd alpine /bin/sh
  docker run --net=macnet222 --ip6=fd18::11 -itd alpine /bin/sh

Advanced Networking Options

All of the applicable Docker networking options are available to the macvlan and ipvlan drivers. The ones that aren't are likely bridge related. Since we have cut out the need for a bridge with ipvlan/macvlan modes.

Example: The following demonstrates excluding addresses along with dual stack. Let's say your eth0 in on the 192.168.131.0/24 and has a secondary address that is also routed by the network for 192.168.133.0/24. Containers will be placed directly onto that network and any address between 192.168.131.2-192.168.131.254 and 192.168.133.2-192.168.133.254 are usable. In some cases the host may have an address on the Docker host eth0 in this example. Since you don't want that address to be used, Libnetwork has the ability to blacklist that address from IPAM handing it out using --aux-address="exclude2=192.168.131.254". The word exclude2 in the --aux-address is completely arbitrary. The only requirement is it needs to be unique from the others in the network since it is a map whose keys will overwrite eachother in the case of collision.

docker network create -d ipvlan  \
  --subnet=192.168.131.0/24 --subnet=192.168.133.0/24 \
  --subnet=192.168.131.1 --subnet=192.168.133.1 \
  --subnet=fd14::/64  \
  --aux-address="exclude1=fd14::2" \
  --aux-address="exclude2=192.168.131.254" \
  --aux-address="exclude3=192.168.133.254" \
  --ip-range=192.168.131.0/25 \
  --ip-range=192.168.133.0/25 \
  -o host_iface=eth0 \
  -o ipvlan_mode=l3 ipnet131

Manually Creating 802.1q Links

Vlan ID 40

If you do not want the driver to create the vlan sub-interface it simply needs to exist prior to the docker network create.

# create a new sub-interface tied to dot1q vlan 40
ip link add link eth0 name eth0.40 type vlan id 40

# enable the new sub-interface
ip link set eth0.40 up

# now add networks and hosts as you would normally by attaching to the master (sub)interface that is tagged
docker network  create  -d ipvlan  --subnet=192.168.40.0/24 --gateway=192.168.40.1 -o host_iface=eth0.40 ipvlan40

# in two separate terminals, start a Docker container and the containers can now ping one another.
docker run --net=ipvlan40 -it --name ivlan_test5 --rm ubuntu
docker run --net=ipvlan40 -it --name ivlan_test6 --rm ubuntu
@jkldgoefgkljefogeg
Copy link

for macvlan 802.1q network, use -o parent=eth0.50 instead of -o host_iface=eth0.50 (macvlan-docker-plugin has been deprecated)

https://github.com/docker/libnetwork/blob/master/docs/macvlan.md

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment