alphp

Hiking DDS238-2 ZN/S energy meter

Document included in the project https://github.com/fawno/Modbus

https://github.com/fawno/Modbus/blob/master/DDS238-2%20ZN-S%20Modbus.md

Modbus holding registers:

Register(s)	Meaning	Scale Unit	Data format	R/W

insdavm

WireGuard Site-to-Site

Accessing a subnet that is behind a WireGuard client using a site-to-site setup

Problem Summary

We want to access a local subnet remotely, but it is behind a NAT firewall and we can't setup port forwarding. Outgoing connections work, but all incoming connections get DROPPED by the ISP's routing policy.

Solution Summary

devbynyden

Setting up openwrt with Telenet WiFree

This guide explains how to setup your openwrt router to interact with Telenet WiFree as a WISP router.
In this case we will connect to WiFree, create a secondary Wifi signal and also have access to the internet on the Lan interface.

With this setup you can have multiple devices connected to the Telenet WiFree Hotspot.

!Important check the Troubleshooting section at the bottom of this page if LAN does not work.

Disclaimer

I only use this at a secondary home. I am not in any way affiliated with Telenet.

zthxxx

Note

For every body who using Win10/11 with new Office that you need to know:

to active Office without crack, just follow https://github.com/WindowsAddict/IDM-Activation-Script,

you wiil only need to run

irm https://massgrave.dev/ias | iex

HarlemSquirrel

## Systemd user unit file for pulseaudio-dlna
# Copy to: ~/.config/systemd/user/pulseaudio-dlna.service
# Enable: systemctl --user enable pulseaudio-dlna

[Unit]
Description=PulseAudio-DLNA Service

[Install]
WantedBy=default.target

chenxiaolong

Switching between AHCI and RAID on the Dell XPS 15 (9560)

This guide likely applies to other models and, potentially, even laptops from other OEMs that have NVME drives. However, I've only tested this on my Dell XPS 15 (9560) with the OEM Windows installation from the Signature Edition model.

Switching from RAID to AHCI

Switching from RAID to AHCI is significantly simpler than switching from AHCI to RAID. All that's needed is a successful boot to Safe Mode.

1. To set the default boot mode to Safe Mode, use msconfig.exe or open an admin cmd/PowerShell window and run:

braian87b

# Linux Interface Bonding on Wireless Link (OpenWrt / LEDE)
# Attention: This was not tested yet.

# Important: WLAN Interfaces must be AP - STA, it does not work in ad-hoc - infraestructure mode.

# This "Adds" two interfaces in to one. In this sample we are using Wireless Interfaces

# Should be equally configured on both ends, even the hash function for the distribution of data packets

# Intallation of required packages:

braian87b

In experience to get a proper working multiple wan configuration using mwan3 starting from scratch you should:

Important: this works well on OpenWRT 15.05.1, on newer versions there was some breaking changes, for example, the wan ifaces have ipv6 capability and now are named with letters ("wan, wanb... , wanc" instead of "wan, wan2... wan3" so wanb6 means 2nd wan ipv6.): https://github.com/openwrt/packages/blob/master/net/mwan3/files/etc/config/mwan3

The official documentation seems to be very detailed and up to date, I recommend reading those first: https://openwrt.org/docs/guide-user/network/wan/multiwan/mwan3 but I recommend to give a look at my config file below, since my approach for policyes is very nice.

First of all: Activate conntrack, docs says that is important and neccesary to get MWAN3 work properly, and it is needed to reboot:

coaxial

Using a simple IR receiver such as IR5040 or TSOPxxxxx and a Raspberry Pi running LibreELEC + Kodi

Enable lirc in Kodi

Edit the file at /flash/config:

• mount -o remount,rw /flash
• vi /flash/config
• append device_tree_overlay=lirc-rpi
• mount -o remount,ro /flash

Connect the receiver

leonjza

# 2017 - @leonjza
#
# Wordpress 4.7.0/4.7.1 Unauthenticated Content Injection PoC
# Full bug description: https://blog.sucuri.net/2017/02/content-injection-vulnerability-wordpress-rest-api.html

# Usage example:
#
# List available posts:
#
# $ python inject.py http://localhost:8070/