mertcanekiz

<?xml version='1.0'?>
<!DOCTYPE fontconfig SYSTEM 'fonts.dtd'>
<fontconfig>
 <match target="font">
  <edit mode="assign" name="rgba">
   <const>rgb</const>
  </edit>
 </match>
 <match target="font">
  <edit mode="assign" name="hinting">

bruvv

Note: this was tested and used on DSM5 and partly on 6. Since V7 I am not using this anymore.

Got and ssh into your box. Find what is using swap:

find /proc -maxdepth 2 -path "/proc/[0-9]*/status" -readable -exec awk -v FS=":" -v TOTSWP="$(cat /proc/swaps | sed 1d | awk 'BEGIN{sum=0} {sum=sum+$(NF-2)} END{print sum}')" '{process[$1]=$2;sub(/^[ \t]+/,"",process[$1]);} END {if(process["VmSwap"] && process["VmSwap"] != "0 kB") {used_swap=process["VmSwap"];sub(/[ a-zA-Z]+/,"",used_swap);percent=(used_swap/TOTSWP*100); printf "%10s %-30s %20s %6.2f%\n",process["Pid"],process["Name"],process["VmSwap"],percent} }' '{}' \;  | awk '{print $(NF-2),$0}' | sort -hr | head | cut -d " " -f2-

Update synoinfo.conf to correct memory in MB (https://www.gbmb.org/gb-to-mb) for 8GB:

Webreaper

# Docker compose to set up containers for all services you need:
# VPN
#   Sonarr, Radarr, Lidarr, Qbittorrent
# Non-VPN
#   Plex, get_iplayer
# Before running docker-compose, you should pre-create all of the following folders.
# Folders for Docker State:
#  /volume1/dockerdata.             - root where this docker-compose.yml should live
#  /volume1/dockerdata/plex         - Plex config and DB
#  /volume1/dockerdata/sonarr       - Sonarr config and DB

jbaranski

Open Port 80 Oracle Cloud Compute Instance (CentOS)

FYI This was harder than it needed to be:

1. Looking at your instance info, find VNIC section, click "Public Subnet".
2. Click on your security list.
3. Add a new entry with the following options:

• "Stateless" = No, "Source" = 0.0.0.0/0, "IP Protocol" = TCP, "Source Port Range" = All, "Destination Port Range" = 80

4. SSH to your instance.
5. While SSH'ed in your instance, run command firewall-cmd --permanent --add-service=http.
6. While SSH'ed in your instance, run command firewall-cmd --reload.
7. Now start Apache, NGINX, or whatever server you need to on port 80. You can now access from the internet.

andrebrait

Here is the best setup (I think so :D) for K-series Keychron keyboards on Linux.

Note: many newer Keychron keyboards use QMK as firmware and most tips here do not apply to them. Maybe the ones related to Bluetooth can be useful, but everything related to Apple's keyboard module (hid_apple) on Linux, won't work. As far as I know, all QMK-based boards use the hid_generic module instead. Examples of QMK-based boards are: Q, Q-Pro, V, K-Pro, etc.

Most of these commands have been tested on Ubuntu 20.04 and should also work on most Debian-based distributions. If a command happens not to work for you, take a look in the comment section.

Make Fn + F-keys work (NOT FOR QMK-BASED BOARDS)

Older Keychron keyboards (those not based on QMK) use the hid_apple driver on Linux, even in the Windows/Android mode, both in Bluetooth and Wired modes.

ta264

#!/bin/bash
set -e

ARCH=aarch64
DOCKER_VERSION=20.10.0
DOCKER_DIR=/volume1/@docker

echo "Downloading docker $DOCKER_VERSION-$ARCH"
curl "https://download.docker.com/linux/static/stable/$ARCH/docker-$DOCKER_VERSION.tgz" | tar -xz -C /usr/local/bin --strip-components=1

bmcbm

# Use systemd for managing NVIDIA driver suspend in drivers ====>>> PRIOR to version 470 <<<=====
# https://download.nvidia.com/XFree86/Linux-x86_64/450.66/README/powermanagement.html
# https://forums.developer.nvidia.com/t/unable-to-set-nvidia-kernel-module-parameters/161306
# Please note: In Fedora Linux you may need to just install the xorg-x11-drv-nvidia-power pakage 
# as sugested by @goombah88 in the comments below. 

TMP_PATH=/var/tmp
TMPL_PATH=/usr/share/doc/nvidia-driver-460/

echo "options nvidia NVreg_PreserveVideoMemoryAllocations=1 NVreg_TemporaryFilePath=${TMP_PATH}" | sudo tee /etc/modprobe.d/nvidia-power-management.conf 

tomdaley92

Proxmox - SPICE client setup for MacOS

1. Install a working (and compiled) version of virt-viewer. You may view the homebrew package's upstream source on GitHub.

   brew tap jeffreywildman/homebrew-virt-manager
   brew install virt-viewer

2. Once that's installed should be able make a call remote-viewer with a pve-spice.vv file downloaded from proxmox web interface

bruvv

synopkg stop pkgctl-SynoFinder
synopkg uninstall SynoFinder

synopkg stop pkgctl-ActiveInsight
synopkg uninstall ActiveInsight

synopkg stop pkgctl-HybrideShare
synopkg uninstall HybrideShare

synopkg stop pkgctl-ScsiTarget

bchaber

<!--
  Put this file in ~/Library/LaunchAgents/com.example.KeyRemapping.plist to
  automatically remap your keys when macOS starts.
  See https://developer.apple.com/library/archive/technotes/tn2450/_index.html for
  the key "usage IDs". Take the usage ID and add 0x700000000 to it before putting it
  into a source or destination (HIDKeyboardModifierMappingSrc and
  HIDKeyboardModifierMappingDst respectively).
-->
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">