Skip to content

Instantly share code, notes, and snippets.

View zankich's full-sized avatar

Adrian Zankich zankich

85 followers · 0 following
  • California
View GitHub Profile
@zankich
zankich / 01-getting_started.md
Last active May 2, 2019 01:42
Gophercon getting started with Gobot

First go to the Gobot Intel Edison Readme (https://github.com/hybridgroup/gobot/tree/master/platforms/intel-iot/edison#how-to-install) and follow the getting started guide. Your Edison has already been updated to the latest firmware version,
so you can skip that part! You will not need to download the Intel XDK, you only need to go through the steps detailing how to connect through the serial interface and then configure your edison.

Find the box called "Base Shield" and open that up and place the grove "Base Shield" onto your Intel Edison. This will allow you to use the Grove connectors shields and cables!

@zankich
zankich / bbb_connect.sh
Last active April 1, 2019 10:56
connect to your beaglebone black using the usb->ethernet and forward the internet from your host computer to the beaglebone black
#!/bin/bash
#
# run this script on your linux host computer to connect to the bbb and forward your internet.
# be sure to replace "enp0s20u1" with the appropriate usb device for your bbb, which can be found
# by doing an "ifconfig" on your host computer.
#
sudo -- sh -c 'echo 1 > /proc/sys/net/ipv4/ip_forward'
sudo iptables -A POSTROUTING -t nat -j MASQUERADE
@zankich
zankich / battery.js
Created June 9, 2015 21:30
"use strict";
var bebop = require("../.");
var drone = bebop.createClient();
drone.connect();
drone.on("battery", function(data) {
console.log("percentage: ", data);
@zankich
zankich / 01-firmata_blink.go
Last active September 4, 2015 03:30
O'Reilly Gobot Webcast 2015
@zankich
zankich / robot_blink.go
Created April 13, 2015 21:23
@zankich
zankich / dualshock3.json
Created April 7, 2015 20:50
go miami presentation
{
"name": "Sony PLAYSTATION(R)3 Controller",
"guid": "030000004c0500006802000011010000",
"axis": [
{
"name": "left_x",
"id": 0
},
{
"name": "left_y",
@zankich
zankich / 1.js
Last active August 29, 2015 14:16 — forked from chrismatthieu/1.js
// curl -X POST -d '{"devices": "db895340-c344-11e4-9f09-df7578d68eac", "payload": [{"pin":9, "mode":1, "value":1}, {"pin":13, "mode":1, "value":1}]}' http://meshblu.octoblu.com/messages --header "meshblu_auth_uuid: db895340-c344-11e4-9f09-df7578d68eac" --header "meshblu_auth_token: d0a9f0d7e321657a38d25dd492492ffed0baf773"
var Cylon = require('cylon');
Cylon.robot({
connections: {
arduino: { adaptor: 'firmata', port: '/dev/tty.usbmodem1411' },
skynet: { adaptor: 'skynet', uuid: "db895340-c344-11e4-9f09-df7578d68eac", token: "d0a9f0d7e321657a38d25dd492492ffed0baf773" }
},
@zankich
zankich / 1.js
Last active August 29, 2015 14:16 — forked from chrismatthieu/gist:8c6b8b3731d3ebd03686
var Cylon = require('cylon');
Cylon.robot({
connections: {
arduino: { adaptor: 'firmata', port: '/dev/tty.usbmodem1411' },
skynet: { adaptor: 'skynet', uuid: "db895340-c344-11e4-9f09-df7578d68eac", token: "d0a9f0d7e321657a38d25dd492492ffed0baf773" }
},
work: function(my) {
my.skynet.on('message', function(data) {
data.forEach(function(o) {
@zankich
zankich / sphero_shake_points.js
Last active August 29, 2015 14:07
var Cylon = require('cylon');
Cylon.robot({
connection: { name: 'sphero', adaptor: 'sphero', port: '/dev/rfcomm0' },
device: { name: 'sphero', driver: 'sphero' },
red: 0,
green: 0,
blue: 255,
shakePower: 0,
currentLevel: 0,
@zankich
zankich / steps.md
Last active July 24, 2018 18:02
Gobot firmata instructions for Windows
  1. Install gort
  1. Install arduino dependencies and flash firmata
  • Make sure you are running your terminal as an Administrator
  • $ ./gort arduino install
  • reload your env variables, or close your cmd prompt and open a new one
  • $ ./gort scan serial
  • Take note of the COM port listed, this should be your arduino