Created
March 28, 2024 19:33
-
-
Save Adenilson/4d0a763a456b0e0ff231eed05240b646 to your computer and use it in GitHub Desktop.
K230 first boot
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
root@hp:/home/adenilson/Desktop/intel/risc/image# cu -l ttyACM0 | |
Connected. | |
boot failed with exit code 19 | |
U-Boot SPL 2022.10-00027-g761ca9d596 (Dec 06 2023 - 13:08:49 +0200) | |
00000000: PMU Major Msg: End of CA training | |
00000000: PMU Major Msg: End of initialization | |
00000000: PMU Major Msg: End of read enable training | |
00000000: PMU Major Msg: End of fine write leveling | |
00000000: PMU Major Msg: End of read dq deskew training | |
00000000: PMU Major Msg: End of MPR read delay center optimization | |
00000000: PMU Major Msg: End of Write leveling coarse delay | |
00000000: PMU Major Msg: End of write delay center optimization | |
00000000: PMU Major Msg: End of read delay center optimization | |
00000000: PMU Major Msg: End of max read latency training | |
00000000: PMU Major Msg: Firmware run has completed | |
U-Boot 2022.10-00027-g761ca9d596 (Dec 06 2023 - 13:08:49 +0200) | |
CPU: rv64imafdcvsu | |
Model: kendryte k230 evb | |
DRAM: 512 MiB | |
Core: 23 devices, 15 uclasses, devicetree: embed | |
MMC: mmc0@91580000: 0, mmc1@91581000: 1 | |
Loading Environment from MMC... *** Warning - bad CRC, using default environment | |
In: serial@91400000 | |
Out: serial@91400000 | |
Err: serial@91400000 | |
Net: No ethernet found. | |
Hit any key to stop autoboot: 0 | |
switch to partitions #0, OK | |
mmc1 is current device | |
Scanning mmc 1:5... | |
K230# | |
K230# | |
K230# | |
K230# help | |
? - alias for 'help' | |
base - print or set address offset | |
bdinfo - print Board Info structure | |
blkcache - block cache diagnostics and control | |
boot - boot default, i.e., run 'bootcmd' | |
boot_baremetal- boot_baremetal | |
bootd - boot default, i.e., run 'bootcmd' | |
bootelf - Boot from an ELF image in memory | |
bootflow - Boot flows | |
booti - boot Linux kernel 'Image' format from memory | |
bootm - boot application image from memory | |
bootmeth - Boot methods | |
bootp - boot image via network using BOOTP/TFTP protocol | |
bootvx - Boot vxWorks from an ELF image | |
cmp - memory compare | |
coninfo - print console devices and information | |
cp - memory copy | |
crc32 - checksum calculation | |
dhcp - boot image via network using DHCP/TFTP protocol | |
dm - Driver model low level access | |
echo - echo args to console | |
editenv - edit environment variable | |
env - environment handling commands | |
erase - erase FLASH memory | |
eraseenv - erase environment variables from persistent storage | |
exit - exit script | |
ext2load - load binary file from a Ext2 filesystem | |
ext2ls - list files in a directory (default /) | |
ext4load - load binary file from a Ext4 filesystem | |
ext4ls - list files in a directory (default /) | |
ext4size - determine a file's size | |
false - do nothing, unsuccessfully | |
fatinfo - print information about filesystem | |
fatload - load binary file from a dos filesystem | |
fatls - list files in a directory (default /) | |
fatmkdir - create a directory | |
fatrm - delete a file | |
fatsize - determine a file's size | |
fatwrite - write file into a dos filesystem | |
fdt - flattened device tree utility commands | |
flinfo - print FLASH memory information | |
fstype - Look up a filesystem type | |
fstypes - List supported filesystem types | |
go - start application at address 'addr' | |
gpt - GUID Partition Table | |
gtime - gtime | |
gzwrite - unzip and write memory to block device | |
help - print command description/usage | |
iminfo - print header information for application image | |
imxtract - extract a part of a multi-image | |
itest - return true/false on integer compare | |
k230_unzip- k230_unzip | |
ln - Create a symbolic link | |
load - load binary file from a filesystem | |
loadb - load binary file over serial line (kermit mode) | |
loads - load S-Record file over serial line | |
loadx - load binary file over serial line (xmodem mode) | |
loady - load binary file over serial line (ymodem mode) | |
loop - infinite loop on address range | |
ls - list files in a directory (default /) | |
lzmadec - lzma uncompress a memory region | |
md - memory display | |
md5sum - compute MD5 message digest | |
mii - MII utility commands | |
mm - memory modify (auto-incrementing address) | |
mmc - MMC sub system | |
mmcinfo - display MMC info | |
mtd - MTD utils | |
mtest - simple RAM read/write test | |
mw - memory write (fill) | |
net - NET sub-system | |
nfs - boot image via network using NFS protocol | |
nm - memory modify (constant address) | |
panic - Panic with optional message | |
part - disk partition related commands | |
ping - send ICMP ECHO_REQUEST to network host | |
printenv - print environment variables | |
protect - enable or disable FLASH write protection | |
pxe - commands to get and boot from pxe files | |
random - fill memory with random pattern | |
reset - Perform RESET of the CPU | |
run - run commands in an environment variable | |
save - save file to a filesystem | |
saveenv - save environment variables to persistent storage | |
setenv - set environment variables | |
setexpr - set environment variable as the result of eval expression | |
sf - SPI flash sub-system | |
showvar - print local hushshell variables | |
size - determine a file's size | |
sleep - delay execution for some time | |
source - run script from memory | |
sysboot - command to get and boot from syslinux files | |
test - minimal test like /bin/sh | |
tftpboot - load file via network using TFTP protocol | |
true - do nothing, successfully | |
unlz4 - lz4 uncompress a memory region | |
unzip - unzip a memory region | |
usb - USB sub-system | |
usbboot - boot from USB device | |
version - print monitor, compiler and linker version | |
K230# | |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment