Last active
December 17, 2017 22:48
-
-
Save AkBKukU/5ac83b622204c26f7fbc56acf171f61b to your computer and use it in GitHub Desktop.
log of repeated bed leveling
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
start | |
echo: External Reset | |
Marlin 1.1.7 | |
echo: Last Updated: 2017-12-15 12:00 | Author: (Bob Kuhn, Anet config) | |
echo:Compiled: Dec 16 2017 | |
echo: Free Memory: 11898 PlannerBufferBytes: 1232 | |
echo:V47 stored settings retrieved (774 bytes; crc 54390) | |
echo: G21 ; Units in mm | |
echo: M149 C ; Units in Celsius | |
echo:Filament settings: Disabled | |
echo: M200 D1.75 | |
echo: M200 D0 | |
echo:Steps per unit: | |
echo: M92 X100.00 Y100.00 Z400.00 E100.00 | |
echo:Maximum feedrates (units/s): | |
echo: M203 X400.00 Y400.00 Z8.00 E50.00 | |
echo:Maximum Acceleration (units/s2): | |
echo: M201 X2000 Y2000 Z100 E10000 | |
echo:Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel> | |
echo: M204 P400.00 R1000.00 T1000.00 | |
echo:Advanced: S<min_feedrate> T<min_travel_feedrate> B<min_segment_time_us> X<max_xy_jerk> Z<max_z_jerk> E<max_e_jerk> | |
echo: M205 S0.00 T0.00 B20000 X20.00 Y20.00 Z0.30 E5.00 | |
echo:Home offset: | |
echo: M206 X0.00 Y0.00 Z0.00 | |
echo:Auto Bed Leveling: | |
echo:echo: M420 S0 Z10.00 | |
echo:Material heatup parameters: | |
echo: M145 S0 H190 B60 F0 | |
echo: M145 S1 H240 B90 F0 | |
echo:PID settings: | |
echo: M301 P21.00 I1.25 D86.00 | |
echo:Z-Probe Offset (mm): | |
echo: M851 Z-1.21 | |
echo:SD card ok | |
X:124.00 Y:151.00 Z:11.21 E:0.00 Count X:12400 Y:15100 Z:4484 | |
ok | |
Bilinear Leveling Grid: | |
0 1 2 3 4 5 6 | |
0 +0.182 +0.100 +0.030 -0.007 -0.015 +0.013 +0.100 | |
1 +0.150 +0.093 +0.083 +0.050 +0.025 +0.080 +0.168 | |
2 +0.123 +0.078 +0.060 +0.023 +0.025 +0.093 +0.230 | |
3 +0.020 +0.010 +0.063 +0.003 +0.080 +0.160 +0.305 | |
4 -0.037 -0.010 +0.010 +0.030 +0.088 +0.228 +0.375 | |
5 -0.117 -0.127 -0.012 +0.015 +0.093 +0.260 +0.430 | |
6 -0.087 -0.075 +0.015 +0.060 +0.155 +0.320 +0.523 | |
X:203.00 Y:206.00 Z:10.69 E:0.00 Count X:20300 Y:20600 Z:4484 | |
ok | |
Bilinear Leveling Grid: | |
0 1 2 3 4 5 6 | |
0 -0.270 -0.357 -0.440 -0.492 -0.530 -0.510 -0.407 | |
1 -0.427 -0.400 -0.447 -0.502 -0.520 -0.460 -0.352 | |
2 -0.455 -0.465 -0.490 -0.505 -0.502 -0.415 -0.330 | |
3 -0.522 -0.520 -0.527 -0.535 -0.465 -0.377 -0.260 | |
4 -0.587 -0.540 -0.537 -0.522 -0.430 -0.327 -0.185 | |
5 -0.577 -0.527 -0.507 -0.447 -0.367 -0.245 -0.092 | |
6 -0.655 -0.602 -0.520 -0.462 -0.387 -0.212 +0.023 | |
X:203.00 Y:206.00 Z:10.69 E:0.00 Count X:20300 Y:20600 Z:4484 | |
ok | |
Bilinear Leveling Grid: | |
0 1 2 3 4 5 6 | |
0 -0.867 -0.895 -0.965 -1.030 -1.075 -1.035 -0.960 | |
1 -0.942 -0.967 -1.000 -1.042 -1.065 -0.970 -0.895 | |
2 -0.975 -1.007 -1.025 -1.020 -1.045 -0.940 -0.807 | |
3 -0.967 -0.997 -0.995 -1.020 -0.970 -0.880 -0.745 | |
4 -1.035 -1.045 -1.042 -1.005 -0.977 -0.870 -0.720 | |
5 -1.175 -1.115 -1.100 -1.035 -0.950 -0.792 -0.625 | |
6 -1.210 -1.127 -1.067 -0.988 -0.935 -0.770 -0.520 | |
X:203.00 Y:206.00 Z:10.69 E:0.00 Count X:20300 Y:20600 Z:4484 | |
ok | |
Bilinear Leveling Grid: | |
0 1 2 3 4 5 6 | |
0 -1.312 -1.430 -1.472 -1.530 -1.575 -1.545 -1.465 | |
1 -1.377 -1.457 -1.480 -1.535 -1.557 -1.500 -1.400 | |
2 -1.430 -1.472 -1.490 -1.522 -1.542 -1.442 -1.357 | |
3 -1.502 -1.505 -1.527 -1.542 -1.490 -1.395 -1.260 | |
4 -1.560 -1.572 -1.560 -1.545 -1.482 -1.352 -1.202 | |
5 -1.707 -1.645 -1.585 -1.512 -1.457 -1.310 -1.132 | |
6 -1.697 -1.620 -1.562 -1.510 -1.417 -1.237 -1.027 | |
X:203.00 Y:206.00 Z:10.69 E:0.00 Count X:20300 Y:20600 Z:4484 | |
ok |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
start | |
echo: External Reset | |
Marlin 1.1.7 | |
echo: Last Updated: 2017-12-15 12:00 | Author: (Bob Kuhn, Anet config) | |
echo:Compiled: Dec 17 2017 | |
echo: Free Memory: 12164 PlannerBufferBytes: 1232 | |
echo:V47 stored settings retrieved (774 bytes; crc 54390) | |
echo: G21 ; Units in mm | |
echo: M149 C ; Units in Celsius | |
echo:Filament settings: Disabled | |
echo: M200 D1.75 | |
echo: M200 D0 | |
echo:Steps per unit: | |
echo: M92 X100.00 Y100.00 Z400.00 E100.00 | |
echo:Maximum feedrates (units/s): | |
echo: M203 X400.00 Y400.00 Z8.00 E50.00 | |
echo:Maximum Acceleration (units/s2): | |
echo: M201 X2000 Y2000 Z100 E10000 | |
echo:Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel> | |
echo: M204 P400.00 R1000.00 T1000.00 | |
echo:Advanced: S<min_feedrate> T<min_travel_feedrate> B<min_segment_time_us> X<max_xy_jerk> Z<max_z_jerk> E<max_e_jerk> | |
echo: M205 S0.00 T0.00 B20000 X20.00 Y20.00 Z0.30 E5.00 | |
echo:Home offset: | |
echo: M206 X0.00 Y0.00 Z0.00 | |
echo:Auto Bed Leveling: | |
echo:echo: M420 S0 | |
echo:Material heatup parameters: | |
echo: M145 S0 H190 B60 F0 | |
echo: M145 S1 H240 B90 F0 | |
echo:PID settings: | |
echo: M301 P21.00 I1.25 D86.00 | |
echo:Z-Probe Offset (mm): | |
echo: M851 Z-1.21 | |
echo:SD card ok | |
echo:enqueueing "M23 level~1.gco" | |
echo:enqueueing "M24" | |
echo:Now fresh file: level~1.gco | |
File opened: level~1.gco Size: 114 | |
File selected | |
echo:DEBUG: | |
X:124.00 Y:151.00 Z:11.21 E:0.00 Count X:12400 Y:15100 Z:4484 | |
Bed Height Topography: | |
+--- BACK --+ | |
| | | |
L | (+) | R | |
E | | I | |
F | (-) N (+) | G | |
T | | H | |
| (-) | T | |
| | | |
O-- FRONT --+ | |
(0,0) | |
-897.40747 -896.71496 | |
-897.04998 -897.20251 | |
X:204.02 Y:211.00 Z:10.68 E:0.00 Count X:20400 Y:21100 Z:4484 | |
Bed Height Topography: | |
+--- BACK --+ | |
| | | |
L | (+) | R | |
E | | I | |
F | (-) N (+) | G | |
T | | H | |
| (-) | T | |
| | | |
O-- FRONT --+ | |
(0,0) | |
-897.55255 -896.87506 | |
-897.23004 -897.32257 | |
X:204.02 Y:211.00 Z:11.04 E:0.00 Count X:20400 Y:21100 Z:4484 | |
Bed Height Topography: | |
+--- BACK --+ | |
| | | |
L | (+) | R | |
E | | I | |
F | (-) N (+) | G | |
T | | H | |
| (-) | T | |
| | | |
O-- FRONT --+ | |
(0,0) | |
-897.31878 -896.68878 | |
-896.99377 -897.18878 | |
X:204.01 Y:211.01 Z:11.02 E:0.00 Count X:20400 Y:21100 Z:4484 | |
Bed Height Topography: | |
+--- BACK --+ | |
| | | |
L | (+) | R | |
E | | I | |
F | (-) N (+) | G | |
T | | H | |
| (-) | T | |
| | | |
O-- FRONT --+ | |
(0,0) | |
-897.16442 -896.54693 | |
-896.83190 -896.99194 | |
X:204.01 Y:211.00 Z:11.03 E:0.00 Count X:20400 Y:21100 Z:4484 | |
Bed Height Topography: | |
+--- BACK --+ | |
| | | |
L | (+) | R | |
E | | I | |
F | (-) N (+) | G | |
T | | H | |
| (-) | T | |
| | | |
O-- FRONT --+ | |
(0,0) | |
-897.01068 -896.38067 | |
-896.65814 -896.85815 | |
X:204.01 Y:211.00 Z:11.04 E:0.00 Count X:20400 Y:21100 Z:4484 | |
Bed Height Topography: | |
+--- BACK --+ | |
| | | |
L | (+) | R | |
E | | I | |
F | (-) N (+) | G | |
T | | H | |
| (-) | T | |
| | | |
O-- FRONT --+ | |
(0,0) | |
-896.82312 -896.23565 | |
-896.48565 -896.64813 | |
X:204.01 Y:211.00 Z:11.10 E:0.00 Count X:20400 Y:21100 Z:4484 | |
start | |
echo: External Reset | |
Marlin 1.1.7 | |
echo: Last Updated: 2017-12-15 12:00 | Author: (Bob Kuhn, Anet config) | |
echo:Compiled: Dec 17 2017 | |
echo: Free Memory: 12052 PlannerBufferBytes: 1232 | |
echo:V47 stored settings retrieved (774 bytes; crc 54390) | |
echo: G21 ; Units in mm | |
echo: M149 C ; Units in Celsius | |
echo:Filament settings: Disabled | |
echo: M200 D1.75 | |
echo: M200 D0 | |
echo:Steps per unit: | |
echo: M92 X100.00 Y100.00 Z400.00 E100.00 | |
echo:Maximum feedrates (units/s): | |
echo: M203 X400.00 Y400.00 Z8.00 E50.00 | |
echo:Maximum Acceleration (units/s2): | |
echo: M201 X2000 Y2000 Z100 E10000 | |
echo:Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel> | |
echo: M204 P400.00 R1000.00 T1000.00 | |
echo:Advanced: S<min_feedrate> T<min_travel_feedrate> B<min_segment_time_us> X<max_xy_jerk> Z<max_z_jerk> E<max_e_jerk> | |
echo: M205 S0.00 T0.00 B20000 X20.00 Y20.00 Z0.30 E5.00 | |
echo:Home offset: | |
echo: M206 X0.00 Y0.00 Z0.00 | |
echo:Auto Bed Leveling: | |
echo:echo: M420 S0 Z10.00 | |
echo:Material heatup parameters: | |
echo: M145 S0 H190 B60 F0 | |
echo: M145 S1 H240 B90 F0 | |
echo:PID settings: | |
echo: M301 P21.00 I1.25 D86.00 | |
echo:Z-Probe Offset (mm): | |
echo: M851 Z-1.21 | |
X:124.00 Y:151.00 Z:11.21 E:0.00 Count X:12400 Y:15100 Z:4484 | |
ok | |
echo:SD card ok | |
echo:DEBUG: | |
ok | |
measured_z: 0.03, zoffset: 0.00 | |
measured_z: 0.23, zoffset: 0.00 | |
measured_z: -0.14, zoffset: 0.00 | |
measured_z: 0.50, zoffset: 0.00 | |
Bilinear Leveling Grid: | |
0 1 | |
0 +0.228 +0.033 | |
1 -0.137 +0.500 | |
X:204.00 Y:211.00 Z:10.71 E:0.00 Count X:20400 Y:21100 Z:4484 | |
ok | |
measured_z: -0.46, zoffset: 0.00 | |
measured_z: -0.34, zoffset: 0.00 | |
measured_z: -0.66, zoffset: 0.00 | |
measured_z: -0.02, zoffset: 0.00 | |
Bilinear Leveling Grid: | |
0 1 | |
0 -0.342 -0.457 | |
1 -0.662 -0.020 | |
X:204.00 Y:211.00 Z:10.71 E:0.00 Count X:20400 Y:21100 Z:4484 | |
ok | |
measured_z: -0.95, zoffset: 0.00 | |
measured_z: -0.72, zoffset: 0.00 | |
measured_z: -1.10, zoffset: 0.00 | |
measured_z: -0.52, zoffset: 0.00 | |
Bilinear Leveling Grid: | |
0 1 | |
0 -0.725 -0.950 | |
1 -1.102 -0.517 | |
X:204.00 Y:211.00 Z:10.71 E:0.00 Count X:20400 Y:21100 Z:4484 | |
ok | |
start | |
echo: External Reset | |
Marlin 1.1.7 | |
echo: Last Updated: 2017-12-15 12:00 | Author: (Bob Kuhn, Anet config) | |
echo:Compiled: Dec 17 2017 | |
echo: Free Memory: 12042 PlannerBufferBytes: 1232 | |
echo:V47 stored settings retrieved (774 bytes; crc 54390) | |
echo: G21 ; Units in mm | |
echo: M149 C ; Units in Celsius | |
echo:Filament settings: Disabled | |
echo: M200 D1.75 | |
echo: M200 D0 | |
echo:Steps per unit: | |
echo: M92 X100.00 Y100.00 Z400.00 E100.00 | |
echo:Maximum feedrates (units/s): | |
echo: M203 X400.00 Y400.00 Z8.00 E50.00 | |
echo:Maximum Acceleration (units/s2): | |
echo: M201 X2000 Y2000 Z100 E10000 | |
echo:Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel> | |
echo: M204 P400.00 R1000.00 T1000.00 | |
echo:Advanced: S<min_feedrate> T<min_travel_feedrate> B<min_segment_time_us> X<max_xy_jerk> Z<max_z_jerk> E<max_e_jerk> | |
echo: M205 S0.00 T0.00 B20000 X20.00 Y20.00 Z0.30 E5.00 | |
echo:Home offset: | |
echo: M206 X0.00 Y0.00 Z0.00 | |
echo:Auto Bed Leveling: | |
echo:echo: M420 S0 Z10.00 | |
echo:Material heatup parameters: | |
echo: M145 S0 H190 B60 F0 | |
echo: M145 S1 H240 B90 F0 | |
echo:PID settings: | |
echo: M301 P21.00 I1.25 D86.00 | |
echo:Z-Probe Offset (mm): | |
echo: M851 Z-1.21 | |
X:124.00 Y:151.00 Z:11.21 E:0.00 Count X:12400 Y:15100 Z:4484 | |
ok | |
echo:SD card ok | |
echo:DEBUG: | |
ok | |
run_z_probe(): 1.23, zprobe_zoffset: -1.21 | |
run_z_probe(): 1.43, zprobe_zoffset: -1.21 | |
run_z_probe(): 1.07, zprobe_zoffset: -1.21 | |
run_z_probe(): 1.70, zprobe_zoffset: -1.21 | |
Bilinear Leveling Grid: | |
0 1 | |
0 +0.220 +0.020 | |
1 -0.140 +0.490 | |
X:204.00 Y:211.00 Z:10.72 E:0.00 Count X:20400 Y:21100 Z:4484 | |
ok | |
run_z_probe(): 0.79, zprobe_zoffset: -1.21 | |
run_z_probe(): 0.94, zprobe_zoffset: -1.21 | |
run_z_probe(): 0.61, zprobe_zoffset: -1.21 | |
run_z_probe(): 1.21, zprobe_zoffset: -1.21 | |
Bilinear Leveling Grid: | |
0 1 | |
0 -0.267 -0.417 | |
1 -0.595 +0.003 | |
X:204.00 Y:211.00 Z:10.72 E:0.00 Count X:20400 Y:21100 Z:4484 | |
ok | |
run_z_probe(): 0.32, zprobe_zoffset: -1.21 | |
run_z_probe(): 0.47, zprobe_zoffset: -1.21 | |
run_z_probe(): 0.12, zprobe_zoffset: -1.21 | |
run_z_probe(): 0.73, zprobe_zoffset: -1.21 | |
Bilinear Leveling Grid: | |
0 1 | |
0 -0.740 -0.890 | |
1 -1.087 -0.482 | |
X:204.00 Y:211.00 Z:10.72 E:0.00 Count X:20400 Y:21100 Z:4484 | |
ok | |
start | |
echo: External Reset | |
Marlin 1.1.7 | |
echo: Last Updated: 2017-12-15 12:00 | Author: (Bob Kuhn, Anet config) | |
echo:Compiled: Dec 17 2017 | |
echo: Free Memory: 12018 PlannerBufferBytes: 1232 | |
echo:V47 stored settings retrieved (774 bytes; crc 54390) | |
echo: G21 ; Units in mm | |
echo: M149 C ; Units in Celsius | |
echo:Filament settings: Disabled | |
echo: M200 D1.75 | |
echo: M200 D0 | |
echo:Steps per unit: | |
echo: M92 X100.00 Y100.00 Z400.00 E100.00 | |
echo:Maximum feedrates (units/s): | |
echo: M203 X400.00 Y400.00 Z8.00 E50.00 | |
echo:Maximum Acceleration (units/s2): | |
echo: M201 X2000 Y2000 Z100 E10000 | |
echo:Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel> | |
echo: M204 P400.00 R1000.00 T1000.00 | |
echo:Advanced: S<min_feedrate> T<min_travel_feedrate> B<min_segment_time_us> X<max_xy_jerk> Z<max_z_jerk> E<max_e_jerk> | |
echo: M205 S0.00 T0.00 B20000 X20.00 Y20.00 Z0.30 E5.00 | |
echo:Home offset: | |
echo: M206 X0.00 Y0.00 Z0.00 | |
echo:Auto Bed Leveling: | |
echo:echo: M420 S0 Z10.00 | |
echo:Material heatup parameters: | |
echo: M145 S0 H190 B60 F0 | |
echo: M145 S1 H240 B90 F0 | |
echo:PID settings: | |
echo: M301 P21.00 I1.25 D86.00 | |
echo:Z-Probe Offset (mm): | |
echo: M851 Z-1.21 | |
X:124.00 Y:151.00 Z:11.21 E:0.00 Count X:12400 Y:15100 Z:4484 | |
ok | |
echo:SD card ok | |
echo:DEBUG: | |
ok | |
old current_position[Z_AXIS]11.21new current_position[Z_AXIS]1.20 | |
old current_position[Z_AXIS]6.21new current_position[Z_AXIS]1.38 | |
old current_position[Z_AXIS]6.38new current_position[Z_AXIS]0.99 | |
old current_position[Z_AXIS]5.99new current_position[Z_AXIS]1.64 | |
Bilinear Leveling Grid: | |
0 1 | |
0 +0.168 -0.005 | |
1 -0.220 +0.432 | |
X:204.00 Y:211.00 Z:10.78 E:0.00 Count X:20400 Y:21100 Z:4484 | |
ok | |
old current_position[Z_AXIS]11.21new current_position[Z_AXIS]0.77 | |
old current_position[Z_AXIS]5.78new current_position[Z_AXIS]0.92 | |
old current_position[Z_AXIS]5.93new current_position[Z_AXIS]0.61 | |
old current_position[Z_AXIS]5.61new current_position[Z_AXIS]1.23 | |
Bilinear Leveling Grid: | |
0 1 | |
0 -0.285 -0.435 | |
1 -0.595 +0.023 | |
X:204.00 Y:211.00 Z:10.78 E:0.00 Count X:20400 Y:21100 Z:4484 | |
ok | |
old current_position[Z_AXIS]11.21new current_position[Z_AXIS]0.36 | |
old current_position[Z_AXIS]5.36new current_position[Z_AXIS]0.55 | |
old current_position[Z_AXIS]5.55new current_position[Z_AXIS]0.20 | |
old current_position[Z_AXIS]5.20new current_position[Z_AXIS]0.81 | |
Bilinear Leveling Grid: | |
0 1 | |
0 -0.660 -0.850 | |
1 -1.007 -0.405 | |
X:204.00 Y:211.00 Z:10.78 E:0.00 Count X:20400 Y:21100 Z:4484 | |
ok | |
old current_position[Z_AXIS]11.21new current_position[Z_AXIS]-0.08 | |
old current_position[Z_AXIS]4.92new current_position[Z_AXIS]0.13 | |
old current_position[Z_AXIS]5.13new current_position[Z_AXIS]-0.22 | |
old current_position[Z_AXIS]4.78new current_position[Z_AXIS]0.38 | |
Bilinear Leveling Grid: | |
0 1 | |
0 -1.082 -1.292 | |
1 -1.432 -0.832 | |
X:204.00 Y:211.00 Z:10.78 E:0.00 Count X:20400 Y:21100 Z:4484 | |
ok | |
old current_position[Z_AXIS]11.21new current_position[Z_AXIS]-0.49 | |
old current_position[Z_AXIS]4.51new current_position[Z_AXIS]-0.30 | |
old current_position[Z_AXIS]4.70new current_position[Z_AXIS]-0.64 | |
old current_position[Z_AXIS]4.36new current_position[Z_AXIS]-0.04 | |
Bilinear Leveling Grid: | |
0 1 | |
0 -1.512 -1.702 | |
1 -1.850 -1.252 | |
X:204.00 Y:211.00 Z:10.78 E:0.00 Count X:20400 Y:21100 Z:4484 | |
ok | |
start | |
echo: External Reset | |
Marlin 1.1.7 | |
echo: Last Updated: 2017-12-15 12:00 | Author: (Bob Kuhn, Anet config) | |
echo:Compiled: Dec 17 2017 | |
echo: Free Memory: 12070 PlannerBufferBytes: 1232 | |
echo:V47 stored settings retrieved (774 bytes; crc 54390) | |
echo: G21 ; Units in mm | |
echo: M149 C ; Units in Celsius | |
echo:Filament settings: Disabled | |
echo: M200 D1.75 | |
echo: M200 D0 | |
echo:Steps per unit: | |
echo: M92 X100.00 Y100.00 Z400.00 E100.00 | |
echo:Maximum feedrates (units/s): | |
echo: M203 X400.00 Y400.00 Z8.00 E50.00 | |
echo:Maximum Acceleration (units/s2): | |
echo: M201 X2000 Y2000 Z100 E10000 | |
echo:Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel> | |
echo: M204 P400.00 R1000.00 T1000.00 | |
echo:Advanced: S<min_feedrate> T<min_travel_feedrate> B<min_segment_time_us> X<max_xy_jerk> Z<max_z_jerk> E<max_e_jerk> | |
echo: M205 S0.00 T0.00 B20000 X20.00 Y20.00 Z0.30 E5.00 | |
echo:Home offset: | |
echo: M206 X0.00 Y0.00 Z0.00 | |
echo:Auto Bed Leveling: | |
echo:echo: M420 S0 Z10.00 | |
echo:Material heatup parameters: | |
echo: M145 S0 H190 B60 F0 | |
echo: M145 S1 H240 B90 F0 | |
echo:PID settings: | |
echo: M301 P21.00 I1.25 D86.00 | |
echo:Z-Probe Offset (mm): | |
echo: M851 Z-1.21 | |
X:124.00 Y:151.00 Z:11.21 E:0.00 Count X:12400 Y:15100 Z:4484 | |
ok | |
echo:SD card ok | |
echo:DEBUG:LEVELING | |
ok | |
current_position=(124.00, 151.00, 11.21) : >>> gcode_G29 | |
Machine Type: Cartesian | |
Probe: FIX_MOUNTED_PROBE | |
Probe Offset X:-14 Y:-41 Z:-1.21 (Left-Front & Below Nozzle) | |
Auto Bed Leveling: BILINEAR (disabled) | |
current_position=(124.00, 151.00, 11.21) : sync_plan_position | |
current_position=(124.00, 151.00, 11.21) : set_probe_deployed | |
deploy: 1 | |
do_probe_raise(10.00) | |
>>> do_blocking_move_to(124.00, 151.00, 11.21) | |
<<< do_blocking_move_to | |
current_position=(124.00, 151.00, 11.21) : setup_for_endstop_or_probe_move | |
reset_bed_level | |
>>> probe_pt(190.00, 15.00, no stow) | |
current_position=(124.00, 151.00, 11.21) : | |
>>> do_blocking_move_to(204.00, 56.00, 11.21) | |
<<< do_blocking_move_to | |
current_position=(204.00, 56.00, 11.21) : set_probe_deployed | |
deploy: 1 | |
current_position=(204.00, 56.00, 11.21) : >>> run_z_probe | |
current_position=(204.00, 56.00, 11.21) : >>> do_probe_move | |
>>> do_blocking_move_to(204.00, 56.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(204.00, 56.00, 1.28) : sync_plan_position | |
current_position=(204.00, 56.00, 1.28) : <<< do_probe_move | |
>>> do_blocking_move_to(204.00, 56.00, 6.28) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(15.00, 15.00, no stow) | |
current_position=(204.00, 56.00, 6.28) : | |
>>> do_blocking_move_to(29.00, 56.00, 6.28) | |
<<< do_blocking_move_to | |
current_position=(29.00, 56.00, 6.28) : set_probe_deployed | |
deploy: 1 | |
current_position=(29.00, 56.00, 6.28) : >>> run_z_probe | |
current_position=(29.00, 56.00, 6.28) : >>> do_probe_move | |
>>> do_blocking_move_to(29.00, 56.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(29.00, 56.00, 1.43) : sync_plan_position | |
current_position=(29.00, 56.00, 1.43) : <<< do_probe_move | |
>>> do_blocking_move_to(29.00, 56.00, 6.43) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(15.00, 170.00, no stow) | |
current_position=(29.00, 56.00, 6.43) : | |
>>> do_blocking_move_to(29.00, 211.00, 6.43) | |
<<< do_blocking_move_to | |
current_position=(29.00, 211.00, 6.43) : set_probe_deployed | |
deploy: 1 | |
current_position=(29.00, 211.00, 6.43) : >>> run_z_probe | |
current_position=(29.00, 211.00, 6.43) : >>> do_probe_move | |
>>> do_blocking_move_to(29.00, 211.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(29.00, 211.00, 1.10) : sync_plan_position | |
current_position=(29.00, 211.00, 1.10) : <<< do_probe_move | |
>>> do_blocking_move_to(29.00, 211.00, 6.10) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(190.00, 170.00, no stow) | |
current_position=(29.00, 211.00, 6.10) : | |
>>> do_blocking_move_to(204.00, 211.00, 6.10) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 6.10) : set_probe_deployed | |
deploy: 1 | |
current_position=(204.00, 211.00, 6.10) : >>> run_z_probe | |
current_position=(204.00, 211.00, 6.10) : >>> do_probe_move | |
>>> do_blocking_move_to(204.00, 211.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 1.72) : sync_plan_position | |
current_position=(204.00, 211.00, 1.72) : <<< do_probe_move | |
>>> do_blocking_move_to(204.00, 211.00, 6.72) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
current_position=(204.00, 211.00, 6.72) : set_probe_deployed | |
deploy: 0 | |
do_probe_raise(10.00) | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 11.21) : > probing complete | |
Extrapolate [ 0+ 0+] (done) | |
Extrapolate [ 1- 0+] (done) | |
Extrapolate [ 0+ 1-] (done) | |
Extrapolate [ 1- 1-] (done) | |
Bilinear Leveling Grid: | |
0 1 | |
0 +0.220 +0.067 | |
1 -0.107 +0.510 | |
G29 uncorrected Z:11.21 | |
corrected Z:10.70 | |
current_position=(204.00, 211.00, 10.70) : clean_up_after_endstop_or_probe_move | |
<<< gcode_G29 | |
X:204.00 Y:211.00 Z:10.70 E:0.00 Count X:20400 Y:21100 Z:4484 | |
current_position=(204.00, 211.00, 10.70) : sync_plan_position | |
ok | |
current_position=(204.00, 211.00, 10.70) : >>> gcode_G29 | |
Machine Type: Cartesian | |
Probe: FIX_MOUNTED_PROBE | |
Probe Offset X:-14 Y:-41 Z:-1.21 (Left-Front & Below Nozzle) | |
Auto Bed Leveling: BILINEAR (enabled) | |
ABL Adjustment Z0.51 | |
current_position=(204.00, 211.00, 10.70) : sync_plan_position | |
current_position=(204.00, 211.00, 10.70) : set_probe_deployed | |
deploy: 1 | |
do_probe_raise(10.00) | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 11.21) : setup_for_endstop_or_probe_move | |
>>> probe_pt(190.00, 15.00, no stow) | |
current_position=(204.00, 211.00, 11.21) : | |
>>> do_blocking_move_to(204.00, 56.00, 11.21) | |
<<< do_blocking_move_to | |
current_position=(204.00, 56.00, 11.21) : set_probe_deployed | |
deploy: 1 | |
current_position=(204.00, 56.00, 11.21) : >>> run_z_probe | |
current_position=(204.00, 56.00, 11.21) : >>> do_probe_move | |
>>> do_blocking_move_to(204.00, 56.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(204.00, 56.00, 0.77) : sync_plan_position | |
current_position=(204.00, 56.00, 0.77) : <<< do_probe_move | |
>>> do_blocking_move_to(204.00, 56.00, 5.77) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(15.00, 15.00, no stow) | |
current_position=(204.00, 56.00, 5.77) : | |
>>> do_blocking_move_to(29.00, 56.00, 5.77) | |
<<< do_blocking_move_to | |
current_position=(29.00, 56.00, 5.77) : set_probe_deployed | |
deploy: 1 | |
current_position=(29.00, 56.00, 5.77) : >>> run_z_probe | |
current_position=(29.00, 56.00, 5.77) : >>> do_probe_move | |
>>> do_blocking_move_to(29.00, 56.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(29.00, 56.00, 0.94) : sync_plan_position | |
current_position=(29.00, 56.00, 0.94) : <<< do_probe_move | |
>>> do_blocking_move_to(29.00, 56.00, 5.94) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(15.00, 170.00, no stow) | |
current_position=(29.00, 56.00, 5.94) : | |
>>> do_blocking_move_to(29.00, 211.00, 5.94) | |
<<< do_blocking_move_to | |
current_position=(29.00, 211.00, 5.94) : set_probe_deployed | |
deploy: 1 | |
current_position=(29.00, 211.00, 5.94) : >>> run_z_probe | |
current_position=(29.00, 211.00, 5.94) : >>> do_probe_move | |
>>> do_blocking_move_to(29.00, 211.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(29.00, 211.00, 0.61) : sync_plan_position | |
current_position=(29.00, 211.00, 0.61) : <<< do_probe_move | |
>>> do_blocking_move_to(29.00, 211.00, 5.61) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(190.00, 170.00, no stow) | |
current_position=(29.00, 211.00, 5.61) : | |
>>> do_blocking_move_to(204.00, 211.00, 5.61) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 5.61) : set_probe_deployed | |
deploy: 1 | |
current_position=(204.00, 211.00, 5.61) : >>> run_z_probe | |
current_position=(204.00, 211.00, 5.61) : >>> do_probe_move | |
>>> do_blocking_move_to(204.00, 211.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 1.23) : sync_plan_position | |
current_position=(204.00, 211.00, 1.23) : <<< do_probe_move | |
>>> do_blocking_move_to(204.00, 211.00, 6.23) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
current_position=(204.00, 211.00, 6.23) : set_probe_deployed | |
deploy: 0 | |
do_probe_raise(10.00) | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 11.21) : > probing complete | |
Extrapolate [ 0+ 0+] (done) | |
Extrapolate [ 1- 0+] (done) | |
Extrapolate [ 0+ 1-] (done) | |
Extrapolate [ 1- 1-] (done) | |
Bilinear Leveling Grid: | |
0 1 | |
0 -0.270 -0.437 | |
1 -0.595 +0.023 | |
G29 uncorrected Z:11.21 | |
corrected Z:10.70 | |
current_position=(204.00, 211.00, 10.70) : clean_up_after_endstop_or_probe_move | |
<<< gcode_G29 | |
X:204.00 Y:211.00 Z:10.70 E:0.00 Count X:20400 Y:21100 Z:4484 | |
current_position=(204.00, 211.00, 10.70) : sync_plan_position | |
ok | |
current_position=(204.00, 211.00, 10.70) : >>> gcode_G29 | |
Machine Type: Cartesian | |
Probe: FIX_MOUNTED_PROBE | |
Probe Offset X:-14 Y:-41 Z:-1.21 (Left-Front & Below Nozzle) | |
Auto Bed Leveling: BILINEAR (enabled) | |
ABL Adjustment Z0.51 | |
current_position=(204.00, 211.00, 10.70) : sync_plan_position | |
current_position=(204.00, 211.00, 10.70) : set_probe_deployed | |
deploy: 1 | |
do_probe_raise(10.00) | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 11.21) : setup_for_endstop_or_probe_move | |
>>> probe_pt(190.00, 15.00, no stow) | |
current_position=(204.00, 211.00, 11.21) : | |
>>> do_blocking_move_to(204.00, 56.00, 11.21) | |
<<< do_blocking_move_to | |
current_position=(204.00, 56.00, 11.21) : set_probe_deployed | |
deploy: 1 | |
current_position=(204.00, 56.00, 11.21) : >>> run_z_probe | |
current_position=(204.00, 56.00, 11.21) : >>> do_probe_move | |
>>> do_blocking_move_to(204.00, 56.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(204.00, 56.00, 0.27) : sync_plan_position | |
current_position=(204.00, 56.00, 0.27) : <<< do_probe_move | |
>>> do_blocking_move_to(204.00, 56.00, 5.27) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(15.00, 15.00, no stow) | |
current_position=(204.00, 56.00, 5.27) : | |
>>> do_blocking_move_to(29.00, 56.00, 5.27) | |
<<< do_blocking_move_to | |
current_position=(29.00, 56.00, 5.27) : set_probe_deployed | |
deploy: 1 | |
current_position=(29.00, 56.00, 5.27) : >>> run_z_probe | |
current_position=(29.00, 56.00, 5.27) : >>> do_probe_move | |
>>> do_blocking_move_to(29.00, 56.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(29.00, 56.00, 0.45) : sync_plan_position | |
current_position=(29.00, 56.00, 0.45) : <<< do_probe_move | |
>>> do_blocking_move_to(29.00, 56.00, 5.45) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(15.00, 170.00, no stow) | |
current_position=(29.00, 56.00, 5.45) : | |
>>> do_blocking_move_to(29.00, 211.00, 5.45) | |
<<< do_blocking_move_to | |
current_position=(29.00, 211.00, 5.45) : set_probe_deployed | |
deploy: 1 | |
current_position=(29.00, 211.00, 5.45) : >>> run_z_probe | |
current_position=(29.00, 211.00, 5.45) : >>> do_probe_move | |
>>> do_blocking_move_to(29.00, 211.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(29.00, 211.00, 0.12) : sync_plan_position | |
current_position=(29.00, 211.00, 0.12) : <<< do_probe_move | |
>>> do_blocking_move_to(29.00, 211.00, 5.12) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(190.00, 170.00, no stow) | |
current_position=(29.00, 211.00, 5.12) : | |
>>> do_blocking_move_to(204.00, 211.00, 5.12) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 5.12) : set_probe_deployed | |
deploy: 1 | |
current_position=(204.00, 211.00, 5.12) : >>> run_z_probe | |
current_position=(204.00, 211.00, 5.12) : >>> do_probe_move | |
>>> do_blocking_move_to(204.00, 211.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 0.71) : sync_plan_position | |
current_position=(204.00, 211.00, 0.71) : <<< do_probe_move | |
>>> do_blocking_move_to(204.00, 211.00, 5.71) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
current_position=(204.00, 211.00, 5.71) : set_probe_deployed | |
deploy: 0 | |
do_probe_raise(10.00) | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 11.21) : > probing complete | |
Extrapolate [ 0+ 0+] (done) | |
Extrapolate [ 1- 0+] (done) | |
Extrapolate [ 0+ 1-] (done) | |
Extrapolate [ 1- 1-] (done) | |
Bilinear Leveling Grid: | |
0 1 | |
0 -0.762 -0.942 | |
1 -1.092 -0.502 | |
G29 uncorrected Z:11.21 | |
corrected Z:10.70 | |
current_position=(204.00, 211.00, 10.70) : clean_up_after_endstop_or_probe_move | |
<<< gcode_G29 | |
X:204.00 Y:211.00 Z:10.70 E:0.00 Count X:20400 Y:21100 Z:4484 | |
current_position=(204.00, 211.00, 10.70) : sync_plan_position | |
ok | |
current_position=(204.00, 211.00, 10.70) : >>> gcode_G29 | |
Machine Type: Cartesian | |
Probe: FIX_MOUNTED_PROBE | |
Probe Offset X:-14 Y:-41 Z:-1.21 (Left-Front & Below Nozzle) | |
Auto Bed Leveling: BILINEAR (enabled) | |
ABL Adjustment Z0.51 | |
current_position=(204.00, 211.00, 10.70) : sync_plan_position | |
current_position=(204.00, 211.00, 10.70) : set_probe_deployed | |
deploy: 1 | |
do_probe_raise(10.00) | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 11.21) : setup_for_endstop_or_probe_move | |
>>> probe_pt(190.00, 15.00, no stow) | |
current_position=(204.00, 211.00, 11.21) : | |
>>> do_blocking_move_to(204.00, 56.00, 11.21) | |
<<< do_blocking_move_to | |
current_position=(204.00, 56.00, 11.21) : set_probe_deployed | |
deploy: 1 | |
current_position=(204.00, 56.00, 11.21) : >>> run_z_probe | |
current_position=(204.00, 56.00, 11.21) : >>> do_probe_move | |
>>> do_blocking_move_to(204.00, 56.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(204.00, 56.00, -0.23) : sync_plan_position | |
current_position=(204.00, 56.00, -0.23) : <<< do_probe_move | |
>>> do_blocking_move_to(204.00, 56.00, 4.76) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(15.00, 15.00, no stow) | |
current_position=(204.00, 56.00, 4.76) : | |
>>> do_blocking_move_to(29.00, 56.00, 4.76) | |
<<< do_blocking_move_to | |
current_position=(29.00, 56.00, 4.76) : set_probe_deployed | |
deploy: 1 | |
current_position=(29.00, 56.00, 4.76) : >>> run_z_probe | |
current_position=(29.00, 56.00, 4.76) : >>> do_probe_move | |
>>> do_blocking_move_to(29.00, 56.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(29.00, 56.00, -0.05) : sync_plan_position | |
current_position=(29.00, 56.00, -0.05) : <<< do_probe_move | |
>>> do_blocking_move_to(29.00, 56.00, 4.95) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(15.00, 170.00, no stow) | |
current_position=(29.00, 56.00, 4.95) : | |
>>> do_blocking_move_to(29.00, 211.00, 4.95) | |
<<< do_blocking_move_to | |
current_position=(29.00, 211.00, 4.95) : set_probe_deployed | |
deploy: 1 | |
current_position=(29.00, 211.00, 4.95) : >>> run_z_probe | |
current_position=(29.00, 211.00, 4.95) : >>> do_probe_move | |
>>> do_blocking_move_to(29.00, 211.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(29.00, 211.00, -0.41) : sync_plan_position | |
current_position=(29.00, 211.00, -0.41) : <<< do_probe_move | |
>>> do_blocking_move_to(29.00, 211.00, 4.59) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(190.00, 170.00, no stow) | |
current_position=(29.00, 211.00, 4.59) : | |
>>> do_blocking_move_to(204.00, 211.00, 4.59) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 4.59) : set_probe_deployed | |
deploy: 1 | |
current_position=(204.00, 211.00, 4.59) : >>> run_z_probe | |
current_position=(204.00, 211.00, 4.59) : >>> do_probe_move | |
>>> do_blocking_move_to(204.00, 211.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 0.21) : sync_plan_position | |
current_position=(204.00, 211.00, 0.21) : <<< do_probe_move | |
>>> do_blocking_move_to(204.00, 211.00, 5.21) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
current_position=(204.00, 211.00, 5.21) : set_probe_deployed | |
deploy: 0 | |
do_probe_raise(10.00) | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 11.21) : > probing complete | |
Extrapolate [ 0+ 0+] (done) | |
Extrapolate [ 1- 0+] (done) | |
Extrapolate [ 0+ 1-] (done) | |
Extrapolate [ 1- 1-] (done) | |
Bilinear Leveling Grid: | |
0 1 | |
0 -1.265 -1.445 | |
1 -1.625 -1.002 | |
G29 uncorrected Z:11.21 | |
corrected Z:10.70 | |
current_position=(204.00, 211.00, 10.70) : clean_up_after_endstop_or_probe_move | |
<<< gcode_G29 | |
X:204.00 Y:211.00 Z:10.70 E:0.00 Count X:20400 Y:21100 Z:4484 | |
current_position=(204.00, 211.00, 10.70) : sync_plan_position | |
ok | |
current_position=(204.00, 211.00, 10.70) : sync_plan_position | |
echo:Bed Leveling Off | |
echo:Fade Height 10.00 | |
ok | |
current_position=(204.00, 211.00, 10.70) : >>> gcode_G29 | |
Machine Type: Cartesian | |
Probe: FIX_MOUNTED_PROBE | |
Probe Offset X:-14 Y:-41 Z:-1.21 (Left-Front & Below Nozzle) | |
Auto Bed Leveling: BILINEAR (disabled) | |
current_position=(204.00, 211.00, 10.70) : sync_plan_position | |
current_position=(204.00, 211.00, 10.70) : set_probe_deployed | |
deploy: 1 | |
do_probe_raise(10.00) | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 11.21) : setup_for_endstop_or_probe_move | |
>>> probe_pt(190.00, 15.00, no stow) | |
current_position=(204.00, 211.00, 11.21) : | |
>>> do_blocking_move_to(204.00, 56.00, 11.21) | |
<<< do_blocking_move_to | |
current_position=(204.00, 56.00, 11.21) : set_probe_deployed | |
deploy: 1 | |
current_position=(204.00, 56.00, 11.21) : >>> run_z_probe | |
current_position=(204.00, 56.00, 11.21) : >>> do_probe_move | |
>>> do_blocking_move_to(204.00, 56.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(204.00, 56.00, -0.75) : sync_plan_position | |
current_position=(204.00, 56.00, -0.75) : <<< do_probe_move | |
>>> do_blocking_move_to(204.00, 56.00, 4.25) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(15.00, 15.00, no stow) | |
current_position=(204.00, 56.00, 4.25) : | |
>>> do_blocking_move_to(29.00, 56.00, 4.25) | |
<<< do_blocking_move_to | |
current_position=(29.00, 56.00, 4.25) : set_probe_deployed | |
deploy: 1 | |
current_position=(29.00, 56.00, 4.25) : >>> run_z_probe | |
current_position=(29.00, 56.00, 4.25) : >>> do_probe_move | |
>>> do_blocking_move_to(29.00, 56.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(29.00, 56.00, -0.55) : sync_plan_position | |
current_position=(29.00, 56.00, -0.55) : <<< do_probe_move | |
>>> do_blocking_move_to(29.00, 56.00, 4.46) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(15.00, 170.00, no stow) | |
current_position=(29.00, 56.00, 4.46) : | |
>>> do_blocking_move_to(29.00, 211.00, 4.46) | |
<<< do_blocking_move_to | |
current_position=(29.00, 211.00, 4.46) : set_probe_deployed | |
deploy: 1 | |
current_position=(29.00, 211.00, 4.46) : >>> run_z_probe | |
current_position=(29.00, 211.00, 4.46) : >>> do_probe_move | |
>>> do_blocking_move_to(29.00, 211.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(29.00, 211.00, -0.94) : sync_plan_position | |
current_position=(29.00, 211.00, -0.94) : <<< do_probe_move | |
>>> do_blocking_move_to(29.00, 211.00, 4.06) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(190.00, 170.00, no stow) | |
current_position=(29.00, 211.00, 4.06) : | |
>>> do_blocking_move_to(204.00, 211.00, 4.06) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 4.06) : set_probe_deployed | |
deploy: 1 | |
current_position=(204.00, 211.00, 4.06) : >>> run_z_probe | |
current_position=(204.00, 211.00, 4.06) : >>> do_probe_move | |
>>> do_blocking_move_to(204.00, 211.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, -0.30) : sync_plan_position | |
current_position=(204.00, 211.00, -0.30) : <<< do_probe_move | |
>>> do_blocking_move_to(204.00, 211.00, 4.70) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
current_position=(204.00, 211.00, 4.70) : set_probe_deployed | |
deploy: 0 | |
do_probe_raise(10.00) | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 11.21) : > probing complete | |
Extrapolate [ 0+ 0+] (done) | |
Extrapolate [ 1- 0+] (done) | |
Extrapolate [ 0+ 1-] (done) | |
Extrapolate [ 1- 1-] (done) | |
Bilinear Leveling Grid: | |
0 1 | |
0 -1.755 -1.965 | |
1 -2.148 -1.510 | |
G29 uncorrected Z:11.21 | |
corrected Z:12.72 | |
current_position=(204.00, 211.00, 12.72) : clean_up_after_endstop_or_probe_move | |
<<< gcode_G29 | |
X:204.00 Y:211.00 Z:12.72 E:0.00 Count X:20400 Y:21100 Z:4484 | |
current_position=(204.00, 211.00, 12.72) : sync_plan_position | |
ok | |
current_position=(204.00, 211.00, 12.72) : >>> gcode_G29 | |
Machine Type: Cartesian | |
Probe: FIX_MOUNTED_PROBE | |
Probe Offset X:-14 Y:-41 Z:-1.21 (Left-Front & Below Nozzle) | |
Auto Bed Leveling: BILINEAR (enabled) | |
ABL Adjustment Z-1.51 | |
current_position=(204.00, 211.00, 12.72) : sync_plan_position | |
current_position=(204.00, 211.00, 12.72) : set_probe_deployed | |
deploy: 1 | |
do_probe_raise(10.00) | |
>>> do_blocking_move_to(204.00, 211.00, 12.72) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 12.72) : setup_for_endstop_or_probe_move | |
>>> probe_pt(190.00, 15.00, no stow) | |
current_position=(204.00, 211.00, 12.72) : | |
>>> do_blocking_move_to(204.00, 56.00, 12.72) | |
<<< do_blocking_move_to | |
current_position=(204.00, 56.00, 12.72) : set_probe_deployed | |
deploy: 1 | |
current_position=(204.00, 56.00, 12.72) : >>> run_z_probe | |
current_position=(204.00, 56.00, 12.72) : >>> do_probe_move | |
>>> do_blocking_move_to(204.00, 56.00, 11.21) | |
<<< do_blocking_move_to | |
current_position=(204.00, 56.00, 11.21) : sync_plan_position | |
current_position=(204.00, 56.00, 11.21) : <<< do_probe_move | |
current_position=(204.00, 56.00, 11.21) : >>> do_probe_move | |
>>> do_blocking_move_to(204.00, 56.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(204.00, 56.00, 0.73) : sync_plan_position | |
current_position=(204.00, 56.00, 0.73) : <<< do_probe_move | |
>>> do_blocking_move_to(204.00, 56.00, 5.74) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(15.00, 15.00, no stow) | |
current_position=(204.00, 56.00, 5.74) : | |
>>> do_blocking_move_to(29.00, 56.00, 5.74) | |
<<< do_blocking_move_to | |
current_position=(29.00, 56.00, 5.74) : set_probe_deployed | |
deploy: 1 | |
current_position=(29.00, 56.00, 5.74) : >>> run_z_probe | |
current_position=(29.00, 56.00, 5.74) : >>> do_probe_move | |
>>> do_blocking_move_to(29.00, 56.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(29.00, 56.00, 0.92) : sync_plan_position | |
current_position=(29.00, 56.00, 0.92) : <<< do_probe_move | |
>>> do_blocking_move_to(29.00, 56.00, 5.92) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(15.00, 170.00, no stow) | |
current_position=(29.00, 56.00, 5.92) : | |
>>> do_blocking_move_to(29.00, 211.00, 5.92) | |
<<< do_blocking_move_to | |
current_position=(29.00, 211.00, 5.92) : set_probe_deployed | |
deploy: 1 | |
current_position=(29.00, 211.00, 5.92) : >>> run_z_probe | |
current_position=(29.00, 211.00, 5.92) : >>> do_probe_move | |
>>> do_blocking_move_to(29.00, 211.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(29.00, 211.00, 0.58) : sync_plan_position | |
current_position=(29.00, 211.00, 0.58) : <<< do_probe_move | |
>>> do_blocking_move_to(29.00, 211.00, 5.58) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
>>> probe_pt(190.00, 170.00, no stow) | |
current_position=(29.00, 211.00, 5.58) : | |
>>> do_blocking_move_to(204.00, 211.00, 5.58) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 5.58) : set_probe_deployed | |
deploy: 1 | |
current_position=(204.00, 211.00, 5.58) : >>> run_z_probe | |
current_position=(204.00, 211.00, 5.58) : >>> do_probe_move | |
>>> do_blocking_move_to(204.00, 211.00, -10.00) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 1.20) : sync_plan_position | |
current_position=(204.00, 211.00, 1.20) : <<< do_probe_move | |
>>> do_blocking_move_to(204.00, 211.00, 6.20) | |
<<< do_blocking_move_to | |
<<< probe_pt | |
current_position=(204.00, 211.00, 6.20) : set_probe_deployed | |
deploy: 0 | |
do_probe_raise(10.00) | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
>>> do_blocking_move_to(204.00, 211.00, 11.21) | |
<<< do_blocking_move_to | |
current_position=(204.00, 211.00, 11.21) : > probing complete | |
Extrapolate [ 0+ 0+] (done) | |
Extrapolate [ 1- 0+] (done) | |
Extrapolate [ 0+ 1-] (done) | |
Extrapolate [ 1- 1-] (done) | |
Bilinear Leveling Grid: | |
0 1 | |
0 -0.290 -0.475 | |
1 -0.627 -0.007 | |
G29 uncorrected Z:11.21 | |
corrected Z:12.72 | |
current_position=(204.00, 211.00, 12.72) : clean_up_after_endstop_or_probe_move | |
<<< gcode_G29 | |
X:204.00 Y:211.00 Z:12.72 E:0.00 Count X:20400 Y:21100 Z:4484 | |
current_position=(204.00, 211.00, 12.72) : sync_plan_position | |
ok |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment