Skip to content

Instantly share code, notes, and snippets.

Embed
What would you like to do?
TP-Link Archer C5v UART Log

UART Log for Maxis TP-Link Archer C5v

4G Dongle plug-in after boot, see #1439

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2020.09.24 03:18:58 =~=~=~=~=~=~=~=~=~=~=~=
BGA IC
Xtal:1
DDR3 init.
DRAMC init done.
Calculate size.
DRAM size=128MB
Set new TRFC.
ddr-1066
7512DRAMC V1.1.2 (0)
EN751221 at Mon Dec 3 10:03:07 UTC 2018 version 1.1 free bootbase
Memory size 128MB
flash base: bc000000
Found SPI Flash 16MiB GD25Q128B at 0xbc000000
tclinux partition size = 0xf90000, real size = 0x7f94c1f2
tclinux partition size < its real size
Press any key in 1 secs to enter boot command mode.
............
Invalid Power GPIO, just return and don't turn on Power LED
the tag fsLen is 0x96bbdf, fsAddr is 0x200000, kernelLen is 0x155735, kernelAddr is 0x200
==> startAddr = 0x80006530
Decompress to 80002000 free_mem_ptr=80600000 free_mem_ptr_end=80780000
75xx: 0x0
Uncompressing [LZMA] ... done.
==> jumpAddr = 0x80006530
Linux version 2.6.36 (root@9025424db348) (gcc version 4.3.6 (Buildroot 2012.05) ) #74 SMP Mon Jan 20 03:40:16 UTC 2020
ISPRAM0: PA=00330000,Size=00010000,enabled
flash_init: flash_base:bc000000
flash_init: flash_base:bc000000
memsize:128MB
EcoNet EN751221 SOC prom init
bootconsole [early0] enabled
CPU revision is: 00019558 (MIPS 34Kc)
Determined physical RAM map:
memory: 07fe0000 @ 00020000 (usable)
Wasting 1024 bytes for tracking 32 unused pages
Zone PFN ranges:
Normal 0x00000020 -> 0x00008000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000020 -> 0x00008000
3 available secondary CPU TC(s)
PERCPU: Embedded 7 pages/cpu @81103000 s7264 r8192 d13216 u65536
pcpu-alloc: s7264 r8192 d13216 u65536 alloc=16*4096
pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32480
Kernel command line: es=1
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00010058
Readback ErrCtl register=00010058
nmi base is 8115c200
Memory: 125304k/130944k available (3288k kernel code, 5640k reserved, 667k data, 204k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:64
CPU frequency 900.00 MHz
Using 199.968 MHz high precision timer.
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
Calibrating delay loop... 598.01 BogoMIPS (lpj=2990080)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
34K sync es set to 1.
Config7: 0x80080500
Limit of 4 TCs set
TLB of 64 entry pairs shared by 2 VPEs
VPE 0: TC 0 1 2, VPE 1: TC 3
IPI buffer pool of 16 buffers
CPU revision is: 00019558 ((null))
TC 1 going on-line as CPU 1
CPU revision is: 00019558 ((null))
TC 2 going on-line as CPU 2
CPU revision is: 00019558 ((null))
TC 3 going on-line as CPU 3
Brought up 4 CPUs
kworker/u:0 used greatest stack depth: 14864 bytes left
NET: Registered protocol family 16
MT7512_pcie_init
check pcie link up status:
isRC0_LINKUP=1
isRC1_LINKUP=1
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
pci 0000:00:01.0: BAR 8: assigned [mem 0x20100000-0x202fffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff]
pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff] (PCI address [0x20000000-0x200fffff]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0: bridge window [io disabled]
pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
pci 0000:00:00.0: bridge window [mem pref disabled]
pci 0000:02:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff 64bit]
pci 0000:02:00.0: BAR 0: set to [mem 0x20100000-0x201fffff 64bit] (PCI address [0x20100000-0x201fffff]
pci 0000:02:00.0: BAR 6: assigned [mem 0x20200000-0x2020ffff pref]
pci 0000:00:01.0: PCI bridge to [bus 02-02]
pci 0000:00:01.0: bridge window [io disabled]
pci 0000:00:01.0: bridge window [mem 0x20100000-0x202fffff]
pci 0000:00:01.0: bridge window [mem pref disabled]
PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
NET: Registered protocol family 8
NET: Registered protocol family 20
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
mt7512_pcie_fixup: 0x1438 = 20000014
mt7512_pcie_fixup: 0x3438 = 20100015
mt7512_pcie_rc1_retrain: 70 = 0047dc11 80 = 01608c12
TC3162 hardware watchdog module loaded.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
fuse init (API version 7.15)
msgmni has been set to 244
io scheduler noop registered (default)
ttyS0 at I/O 0xbfbf0003 (irq = 1) is a TC3162
brd: module loaded
Register flash device:flash0
SPI Flash Init Start
SPI Flash Init Finish
IS_SPIFLASH=0x2, IS_NANDFLASH=0x0, (0xBFA10114)=0x0)
[linux_spi_nand_flash_init] spi nor flash
tc3162: flash device 0x01000000 at 0x1c000000
tc3162: Found SPIFLASH 16MiB GD25Q128B
Creating 7 MTD partitions on "tc3162":
0x000000000000-0x000000020000 : "boot"
0x000000020000-0x000000220000 : "kernel"
0x000000220000-0x000000fc0000 : "rootfs"
0x000000fc0000-0x000000fd0000 : "config2"
0x000000fd0000-0x000000fe0000 : "romfile"
0x000000fe0000-0x000000ff0000 : "config"
0x000000ff0000-0x000001000000 : "radio"
rootfs
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
RT3xxx EHCI/OHCI init.
TP-LINK Kernel Monitor Initializing...
Mirror/redirect action on
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1957 buckets, 51200 max)
ctnetlink v0.93: registering with nfnetlink.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
Bridge firewalling registered
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 204k freed
starting pid 278, tty '': '/etc/init.d/rcS'
mount used greatest stack depth: 14832 bytes left
mkdir used greatest stack depth: 14576 bytes left
cp used greatest stack depth: 14312 bytes left
SCSI subsystem initialized
insmod used greatest stack depth: 14264 bytes left
hotplug used greatest stack depth: 14032 bytes left
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
BGA USB PHY config
port 0 u2_slew_rate_calibration
FM_OUT value = 157(0x0000009D)
SR calibration value = 4
port 1 u2_slew_rate_calibration
FM_OUT value = 150(0x00000096)
SR calibration value = 4
USB driver version: 751221.2.20160516
xhc_mtk xhc_mtk: xHCI Host Controller
xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 1
xhc_mtk xhc_mtk: irq 18, io mem 0x1fb90000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
xhc_mtk xhc_mtk: xHCI Host Controller
xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
insmod used greatest stack depth: 13932 bytes left
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
module_sel: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
tcsmux version: tcsmux V1.1.0.0 (Nov 26 2018-12:01:42).
vlantag_drv_init
TC3162 LED Manager 0.1 init
tcledctrl version: tcledctrl V1.1.0.0 (Jan 20 2020-03:40:54).
[0xff0000]:0x9275
[0xff8000]:0x6276
tccicmd V1.1.0.0 (Jan 20 2020-03:40:57)
ERROR!Create /etc/fwTCver.conf fail!
macType = 0
qdma_lan: physical_size is 0x00200000
ether.c:v1.00-NAPI 29.Mar.2015
eth0: FE MAC Ethernet address: D8:0D:17:BB:20:5A
init eth_vlan proc.
init eth_forward proc.
User External switch ,type 10
Disable forward!
tcPhyVerLookUp 3785 9451
7512 Ge,
[tcPhyInit] in [tcPhyInit] out , r31 = (12, 0x0)
GE Rext AnaCal Done! (1)(0x1f)
GE Rext AnaCal Done! (1)(0x1f)
GE R50 AnaCal Done! (1) (0x21)(0xa1)
GE R50 AnaCal Done! (1) (0x24)(0xa4)
GE R50 AnaCal Done! (1) (0x24)(0xa4)
GE R50 AnaCal Done! (1) (0x24)(0xa4)
GE Tx offset AnaCal Done! (3)(0x23)
GE Tx offset AnaCal Done! (2)(0x2)
GE Tx offset AnaCal Done! (2)(0x22)
GE Tx offset AnaCal Done! (1)(0x1)
GE Tx amp AnaCal Done! (21) (0xb)
GE Tx amp AnaCal Done! (12) (0x14)
GE Tx amp AnaCal Done! (15) (0x11)
GE Tx amp AnaCal Done! (16) (0x10)
tcPhyVerLookUp 3785 9412
7512 Fe,
, port_num = 65528, ephy_addr = 0, ephy_addr_base = 0x8
[tcPhyInit] in [tcPhyInit] out , r31 = (0, 0x0)
FE R50 AnaCal ERROR! (init)
FE R50 AnaCal zcal_ctrl (32)
FE-0 R50 wait! (1)
FE R50 AnaCal ERROR! (init)
FE R50 AnaCal zcal_ctrl (32)
FE-0 R50 wait! (2)
FE R50 AnaCal ERROR! (init)
FE R50 AnaCal zcal_ctrl (32)
FE-0 R50 wait! (3)
FE Tx amp AnaCal ERROR! (init)
FE Tx amp (248)(1)(0) ===
(0)(0)(0)(ce00)(0)(ce00)
(0)(0)(0)(0)(0)
FE-0 Tx amp AnaCal Saturation! (0)(0x0)
FE-0 Tx amp AnaCal Saturation! (0)(0x0)
FE-0 Tx amp AnaCal wait! (1)
FE Tx amp AnaCal ERROR! (init)
FE Tx amp (248)(1)(0) ===
(0)(0)(0)(ce00)(0)(ce00)
(0)(0)(0)(0)(0)
FE-0 Tx amp AnaCal Saturation! (0)(0x0)
FE-0 Tx amp AnaCal Saturation! (0)(0x0)
FE-0 Tx amp AnaCal wait! (2)
FE Tx amp AnaCal ERROR! (init)
FE Tx amp (248)(1)(0) ===
(0)(0)(0)(ce00)(0)(ce00)
(0)(0)(0)(0)(0)
FE-0 Tx amp AnaCal Saturation! (0)(0x0)
FE-0 Tx amp AnaCal Saturation! (0)(0x0)
FE-0 Tx amp AnaCal wait! (3)
tcPhyVerLookUp 3785 9412
7512 Fe,
, port_num = 65529, ephy_addr = 1, ephy_addr_base = 0x8
[tcPhyInit] in [tcPhyInit] out , r31 = (1, 0x0)
FE R50 AnaCal ERROR! (init)
FE R50 AnaCal zcal_ctrl (32)
FE-1 R50 wait! (1)
FE R50 AnaCal ERROR! (init)
FE R50 AnaCal zcal_ctrl (32)
FE-1 R50 wait! (2)
FE R50 AnaCal ERROR! (init)
FE R50 AnaCal zcal_ctrl (32)
FE-1 R50 wait! (3)
FE Tx amp AnaCal ERROR! (init)
FE Tx amp (249)(1)(0) ===
(0)(0)(0)(ce00)(0)(ce00)
(0)(0)(0)(0)(0)
FE-1 Tx amp AnaCal Saturation! (0)(0x0)
FE-1 Tx amp AnaCal Saturation! (0)(0x0)
FE-1 Tx amp AnaCal wait! (1)
FE Tx amp AnaCal ERROR! (init)
FE Tx amp (249)(1)(0) ===
(0)(0)(0)(ce00)(0)(ce00)
(0)(0)(0)(0)(0)
FE-1 Tx amp AnaCal Saturation! (0)(0x0)
FE-1 Tx amp AnaCal Saturation! (0)(0x0)
FE-1 Tx amp AnaCal wait! (2)
FE Tx amp AnaCal ERROR! (init)
FE Tx amp (249)(1)(0) ===
(0)(0)(0)(ce00)(0)(ce00)
(0)(0)(0)(0)(0)
FE-1 Tx amp AnaCal Saturation! (0)(0x0)
FE-1 Tx amp AnaCal Saturation! (0)(0x0)
FE-1 Tx amp AnaCal wait! (3)
tcPhyVerLookUp 3785 9412
7512 Fe,
, port_num = 65530, ephy_addr = 2, ephy_addr_base = 0x8
[tcPhyInit] in [tcPhyInit] out , r31 = (2, 0x0)
FE R50 AnaCal ERROR! (init)
FE R50 AnaCal zcal_ctrl (32)
FE-2 R50 wait! (1)
FE R50 AnaCal ERROR! (init)
FE R50 AnaCal zcal_ctrl (32)
FE-2 R50 wait! (2)
FE R50 AnaCal ERROR! (init)
FE R50 AnaCal zcal_ctrl (32)
FE-2 R50 wait! (3)
FE Tx amp AnaCal ERROR! (init)
FE Tx amp (250)(1)(0) ===
(0)(0)(0)(ce00)(0)(ce00)
(0)(0)(0)(0)(0)
FE-2 Tx amp AnaCal Saturation! (0)(0x0)
FE-2 Tx amp AnaCal Saturation! (0)(0x0)
FE-2 Tx amp AnaCal wait! (1)
FE Tx amp AnaCal ERROR! (init)
FE Tx amp (250)(1)(0) ===
(0)(0)(0)(ce00)(0)(ce00)
(0)(0)(0)(0)(0)
FE-2 Tx amp AnaCal Saturation! (0)(0x0)
FE-2 Tx amp AnaCal Saturation! (0)(0x0)
FE-2 Tx amp AnaCal wait! (2)
FE Tx amp AnaCal ERROR! (init)
FE Tx amp (250)(1)(0) ===
(0)(0)(0)(ce00)(0)(ce00)
(0)(0)(0)(0)(0)
FE-2 Tx amp AnaCal Saturation! (0)(0x0)
FE-2 Tx amp AnaCal Saturation! (0)(0x0)
FE-2 Tx amp AnaCal wait! (3)
tcPhyVerLookUp 3785 9412
7512 Fe,
, port_num = 65531, ephy_addr = 3, ephy_addr_base = 0x8
[tcPhyInit] in [tcPhyInit] out , r31 = (3, 0x0)
FE R50 AnaCal ERROR! (init)
FE R50 AnaCal zcal_ctrl (32)
FE-3 R50 wait! (1)
FE R50 AnaCal ERROR! (init)
FE R50 AnaCal zcal_ctrl (32)
FE-3 R50 wait! (2)
FE R50 AnaCal ERROR! (init)
FE R50 AnaCal zcal_ctrl (32)
FE-3 R50 wait! (3)
FE Tx amp AnaCal ERROR! (init)
FE Tx amp (251)(1)(0) ===
(0)(0)(0)(ce00)(0)(ce00)
(0)(0)(0)(0)(0)
FE-3 Tx amp AnaCal Saturation! (0)(0x0)
FE-3 Tx amp AnaCal Saturation! (0)(0x0)
FE-3 Tx amp AnaCal wait! (1)
FE Tx amp AnaCal ERROR! (init)
FE Tx amp (251)(1)(0) ===
(0)(0)(0)(ce00)(0)(ce00)
(0)(0)(0)(0)(0)
FE-3 Tx amp AnaCal Saturation! (0)(0x0)
FE-3 Tx amp AnaCal Saturation! (0)(0x0)
FE-3 Tx amp AnaCal wait! (2)
FE Tx amp AnaCal ERROR! (init)
FE Tx amp (251)(1)(0) ===
(0)(0)(0)(ce00)(0)(ce00)
(0)(0)(0)(0)(0)
FE-3 Tx amp AnaCal Saturation! (0)(0x0)
FE-3 Tx amp AnaCal Saturation! (0)(0x0)
FE-3 Tx amp AnaCal wait! (3)
tcPhyVerLookUp 3785 9412
7512 Fe,
, port_num = 65532, ephy_addr = 4, ephy_addr_base = 0x8
[tcPhyInit] in [tcPhyInit] out , r31 = (4, 0x0)
FE R50 AnaCal ERROR! (init)
FE R50 AnaCal zcal_ctrl (32)
FE-4 R50 wait! (1)
FE R50 AnaCal ERROR! (init)
FE R50 AnaCal zcal_ctrl (32)
FE-4 R50 wait! (2)
FE R50 AnaCal ERROR! (init)
FE R50 AnaCal zcal_ctrl (32)
FE-4 R50 wait! (3)
FE Tx amp AnaCal ERROR! (init)
FE Tx amp (252)(1)(0) ===
(0)(0)(0)(ce00)(0)(ce00)
(0)(0)(0)(0)(0)
FE-4 Tx amp AnaCal Saturation! (0)(0x0)
FE-4 Tx amp AnaCal Saturation! (0)(0x0)
FE-4 Tx amp AnaCal wait! (1)
FE Tx amp AnaCal ERROR! (init)
FE Tx amp (252)(1)(0) ===
(0)(0)(0)(ce00)(0)(ce00)
(0)(0)(0)(0)(0)
FE-4 Tx amp AnaCal Saturation! (0)(0x0)
FE-4 Tx amp AnaCal Saturation! (0)(0x0)
FE-4 Tx amp AnaCal wait! (2)
FE Tx amp AnaCal ERROR! (init)
FE Tx amp (252)(1)(0) ===
(0)(0)(0)(ce00)(0)(ce00)
(0)(0)(0)(0)(0)
FE-4 Tx amp AnaCal Saturation! (0)(0x0)
FE-4 Tx amp AnaCal Saturation! (0)(0x0)
FE-4 Tx amp AnaCal wait! (3)
tcPhyVerLookUp 3785 0
tcPhyVerLookUp 3785 0
tcPhyVerLookUp 3785 0
tcPhyVerLookUp 3785 0
tcPhyVerLookUp 3785 0
tcPhyVerLookUp 3785 0
tcPhyVerLookUp 3785 0
tcPhyVerLookUp 3785 9451
7512 Ge,
, port_num = 4, ephy_addr = 12, ephy_addr_base = 0x8
[tcPhyInit] in [tcPhyInit] out , r31 = (12, 0x0)
Dying Gasp 0.31 init
oenmap 0 oenmap2 0
Exec. Successful
Exec. Successful
Exec. Successful
macType = 0
qdma_wan: qdma_bmgr.c [2646]: HW_FWD physical size is not illegal, force setting to 4MB
qdma_wan: physical_size is 0x00400000
Exec. Successful
Exec. Successful
Exec. Successful
eth0: starting interface.
netif_start_queue
mount used greatest stack depth: 13784 bytes left
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
PPTP driver version 0.8.5
MTK DSP support
/etc/init.d/rcS: line 123: cmmsyslogd: not found
[1] PCM V2.4 (Oct 17 2017 15:58:58)
Major Num:255, device: spi
init mod-slic3,interface:ZSI,devNum:1,gpio:2000
ZSI
init slicFunc slic1:7 slic2:7
SPI_Reset
SLIC_DeviceVerify
le9662_deviceVerify Start
devInfo->deviceNum=0 res_arr[0]=8 res_arr[0]=75
le9662_deviceVerify Success!
rd_cnt=1
SLIC_SELF_TEST VP886_R_OPCOND_RD = 0x0
SLIC_SELF_TEST WRT VAL = 0x47
SLIC_SELF_TEST RD BACK = 0x47
SLIC WRT RD test Pass
SLIC_SELF_TEST WRT VAL = 0x0
SLIC_SELF_TEST RD BACK = 0x0
SLIC WRT RD test Pass
DEVICE_VERIFY ret:1
le9662_deviceVerify already! Bypass 2nd verify!
DEVICE_VERIFY ret:0
pcm1 ch num:2 pcm2 ch num:0
Init fxsNum(2) + fxoNum(0) = slic_ch_num(:2) , deviceNum(1)
[DBG SLIC_Init:L613]FXS_NUM=2 FXO_NUM=0
le9662_deviceInit 0
le9662_slicParamReset Successful(CountryCode=Default)
device profile len:48
0C FF 00 2C 05 14 46 82
44 46 5E 14 00 F6 95 00
94 30 94 30 E4 04 A0 00
E6 60 22 20 00 FF 21 30
14 30 14 30 14 19 3C FF
95 00 2D 6E 02 3C 02 FD
dc profile len:15
0C 01 00 0B 02 03 C6 91
E5 1C 86 58 80 00 07
ring profile len:22
0C 04 00 12 01 0C C0 08
00 00 00 44 3A 9D 00 00
00 00 AA 02 4E 00
ac profile len:80
A4 00 F4 4C 01 49 CA F5
98 AA 7B AB 2C A3 25 A5
24 B2 3D 9A 2A AA A6 9F
01 8A 1D 01 A3 A0 2E B2
B2 BA AC A2 A6 CB 3B 45
88 2A 20 3C BC 4E A6 2B
A5 2B 3E BA 8F 82 A8 71
80 A9 F0 50 00 86 2A 42
A1 CB 1B A3 A8 FB 87 AA
FB 9F A9 F0 96 2E 01 00
le9662 Init .Calibration completed on both lines
le9662_Init_Cnt = 97
CODEC_LINEAR setting
FXS-0 timeslot:2
FXS-1 timeslot:3
fxs0 gain--TX :4000 RX: 4000
fxs1 gain--TX :4000 RX: 4000
[DBG SLIC_Init:L613]FXS_NUM=2 FXO_NUM=0
Bypass le9662_deviceInit on Device 1!
init mod-ksocket
init mod-acodec
init mod-foip3
===============================
|| MTK DSP init successfully ||
===============================
dbgTool_init init v2.0
pid 410's current affinity mask: (null)
pid 410's new affinity mask: 8
pid 405's current affinity mask: (null)
pid 405's new affinity mask: 8
pid 420's current affinity mask: (null)
pid 420's new affinity mask: 8
pid 418's current affinity mask: (null)
pid 418's new affinity mask: 8
pid 419's current affinity mask: (null)
pid 419's new affinity mask: 8
pid 403's current affinity mask: (null)
pid 403's new affinity mask: 8
Power Manager 0.2 init
ifconfig: SIOCSIFADDR: No such device
Please press Enter to activate this console. iptables used greatest stack depth: 13760 bytes left
[ dm_readFile ] 2061: can not open xml file /var/tmp/pc/reduced_data_model.xml!, about to open file /etc/reduced_data_model.xml
[ initKernelMonitorFd ] 433: *kmFd=7
[ initKernelMonitorFd ] 457: registered fd 7 with kernel monitor
InternetAccessDetect: can't load library 'libxdslctl.so'
HWNAT Module enabled with Type:L2B/IPv4/IPv6/DS-LITE/6RD, foeSzie:80B, foeNum:16384
IP check use Black List
insmod used greatest stack depth: 13704 bytes left
sendto /var/tmp/7 msg 2001 error No such file or directory ,pid 438
[ oal_sys_getOldTZInfo ] 553: Open TZ file error!
ioctl: No such device
use br_hw_addr!
ioctl: No such device
ioctl: No such device
------------[ cut here ]------------
WARNING: at fs/proc/generic.c:589 proc_register+0x218/0x300()
proc_dir_entry 'tc3162/igmp_hwnat' already registered
Modules linked in: hw_nat(P) ipt_webWarn_target(P) pwm(P) pcmDump(P) ovdsp foip(P) acodec_x(P) ortp ksocket(P) fxs3(P) slic3(P) spi(P) lec(P) pcm1(P) DSPCore(P) sys_mod pptp l2tp_ppp l2tp_core ipt_STAT nf_conntrack_pptp nf_conntrack_proto_gre qdma_wan(P) speedtest(P) dying_gasp(P) eth_ephy(P) eth(P) qdma_lan(P) fe_core(P) tccicmd(P) tcledctrl(P) tcvlantag tcsmux module_sel(P) usb_storage xhci_hcd usbcore sd_mod scsi_wait_scan scsi_mod
Call Trace:
[<8000be64>] dump_stack+0x8/0x34
[<80046430>] warn_slowpath_common+0x78/0xa4
[<800464e4>] warn_slowpath_fmt+0x2c/0x38
[<8010871c>] proc_register+0x218/0x300
[<80108914>] create_proc_entry+0x58/0xa0
[<80309374>] igmp_hwnat_init+0x6c/0x9c
[<8030169c>] br_add_bridge+0x100/0x1a8
[<803022dc>] br_ioctl_deviceless_stub+0x240/0x2a8
[<801ee1b0>] sock_ioctl+0x104/0x354
[<800c85f0>] do_vfs_ioctl+0xa4/0x704
[<800c8ca0>] sys_ioctl+0x50/0xb0
[<80004450>] stack_done+0x20/0x40
---[ end trace c5a321329dae05d6 ]---
use br_hw_addr!
device eth0.5 entered promiscuous mode
device eth0 entered promiscuous mode
br0: port 1(eth0.5) entering forwarding state
br0: port 1(eth0.5) entering forwarding state
device eth0.4 entered promiscuous mode
br0: port 2(eth0.4) entering forwarding state
br0: port 2(eth0.4) entering forwarding state
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address device eth0.3 entered promiscuous mode
abr0: port 3(eth0.3) entering forwarding state
br0: port 3(eth0.3) entering forwarding state
lready in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 90; error = Address already in use
igmpd# Err: setsockopt - MRT_ADD_VIF
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Adevice eth0.2 entered promiscuous mode
dbr0: port 4(eth0.2) entering forwarding state
br0: port 4(eth0.2) entering forwarding state
dress already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 90; error = Address already in use
igmpd# Err: setsockopt - MRT_ADD_VIF
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 90; error = Address already in use
igmpd# Err: setsockopt - MRT_ADD_VIF
done
done
ra0 iwpriv used greatest stack depth: 13032 bytes left
no private ioctls.
register mt_drv
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
=== pAd = c1e82000, size = 911664 ===
<-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xc1d80000, csr_addr=0xc1d80000!
device_id =0x7603
RtmpChipOpsHook(507): Not support for HIF_MT yet!
mt7603_init()-->
mt_bcn_buf_init(224): Not support for HIF_MT yet!
<--mt7603_init()
OAL:Writefile 2.4GHz, WscConfigMethods:0x80
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
TX_BCN DESC a51b8000 size = 320
RX[0] DESC a51ba000 size = 2048
RX[1] DESC a51bb000 size = 2048
!!!!!!!!! pCountryRegion is set to 1
!!!!!!!!! pCountryRegion is set to 0
cfg_mode=9
cfg_mode=9
wmode_band_equal(): Band Equal!
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
APCli_WPAPSK_KEY, key string required 8 ~ 64 characters!!!
I/F(apcli0) Key1Str is Invalid key length!
I/F(apcli0) Key2Str is Invalid key length!
I/F(apcli0) Key3Str is Invalid key length!
I/F(apcli0) Key4Str is Invalid key length!
Smart Carrier Sense = 0
FW Version:ap_pcie
FW Build Date:20160107100755
CmdAddressLenReq:(ret = 0)
CmdFwStartReq: override = 1, address = 1048576
CmdStartDLRsp: WiFI FW Download Success
AsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
efuse_probe: efuse = 10000002
RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
RtmpEepromGetDefault::e2p_dafault=1
RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1
NVM is FLASH mode, flash_offset = 0xff0000
1. Phy Mode = 14
exec!
==============eeFlashId: 30098 ====================
@@@ NICReadEEPROMParameters : pAd->FWLoad=0
now bb MainSsid mac d8:0d:17:bb:20:5a
Country Region from e2p = ffff
tssi_1_target_pwr_g_band = 34
2. Phy Mode = 14
3. Phy Mode = 14
NICInitPwrPinCfg(14): Not support for HIF_MT yet!
NICInitializeAsic(584): Not support rtmp_mac_sys_reset () for HIF_MT yet!
mt_mac_init()-->
mt7603_init_mac_cr()-->
AsicSetMacMaxLen(1821): Set the Max RxPktLen=1024!
<--mt_mac_init()
WTBL Segment 1 info:
MemBaseAddr/FID:0x28000/0
EntrySize/Cnt:32/128
WTBL Segment 2 info:
MemBaseAddr/FID:0x40000/0
EntrySize/Cnt:64/128
WTBL Segment 3 info:
MemBaseAddr/FID:0x42000/64
EntrySize/Cnt:64/128
WTBL Segment 4 info:
MemBaseAddr/FID:0x44000/128
EntrySize/Cnt:32/128
MtAsicACQueue: Write CR:21510, Value=10421
MtAsicACQueue: Write CR:21500, Value=10421
AntCfgInit(2571): Not support for HIF_MT yet!
RTMPSetPhyMode(): channel out of range, use first ch=0
MCS Set = ff ff 00 00 01
[BuildAcsScanChList] Support channel: PrimCh=1, CentCh=255, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=2, CentCh=0, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=3, CentCh=1, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=4, CentCh=2, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=5, CentCh=3, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=6, CentCh=4, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=7, CentCh=5, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=8, CentCh=6, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=9, CentCh=7, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=10, CentCh=8, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=11, CentCh=9, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=12, CentCh=10, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=13, CentCh=11, DFS=0, skip 0
=====================================================
Channel 1 : Busy Time = 18363, Score 82,Skip Channel = FALSE
Channel 2 : Busy Time = 21002, Score 79,Skip Channel = FALSE
Channel 3 : Busy Time = 21412, Score 79,Skip Channel = FALSE
Channel 4 : Busy Time = 21717, Score 79,Skip Channel = FALSE
Channel 5 : Busy Time = 22206, Score 78,Skip Channel = FALSE
Channel 6 : Busy Time = 21140, Score 79,Skip Channel = FALSE
Channel 7 : Busy Time = 21179, Score 79,Skip Channel = FALSE
Channel 8 : Busy Time = 15560, Score 85,Skip Channel = FALSE
Channel 9 : Busy Time = 12354, Score 88,Skip Channel = FALSE
Channel 10 : Busy Time = 12439, Score 88,Skip Channel = FALSE
Channel 11 : Busy Time = 921, Score 100,Skip Channel = FALSE
Channel 12 : Busy Time = 12233, Score 88,Skip Channel = TRUE
Channel 13 : Busy Time = 12290, Score 88,Skip Channel = TRUE
=====================================================
[GroupChListInsert] Insert Grp Ch Idx=0,CenChannel=255,CtrlCh=1,BusyTime=19284,SkipGrp=0
[GroupChListInsert] Insert Grp Ch Idx=1,CenChannel=0,CtrlCh=2,BusyTime=40286,SkipGrp=0
[GroupChListInsert] Insert Grp Ch Idx=2,CenChannel=1,CtrlCh=3,BusyTime=40696,SkipGrp=0
[GroupChListInsert] Insert Grp Ch Idx=3,CenChannel=2,CtrlCh=4,BusyTime=41001,SkipGrp=0
[GroupChListInsert] Insert Grp Ch Idx=4,CenChannel=3,CtrlCh=5,BusyTime=41490,SkipGrp=0
[GroupChListInsert] Insert Grp Ch Idx=5,CenChannel=4,CtrlCh=6,BusyTime=22061,SkipGrp=0
[GroupChListInsert] Insert Grp Ch Idx=6,CenChannel=5,CtrlCh=7,BusyTime=43240,SkipGrp=0
[GroupChListInsert] Insert Grp Ch Idx=7,CenChannel=6,CtrlCh=8,BusyTime=37621,SkipGrp=0
[GroupChListInsert] Insert Grp Ch Idx=8,CenChannel=7,CtrlCh=9,BusyTime=34415,SkipGrp=0
[GroupChListInsert] Insert Grp Ch Idx=9,CenChannel=8,CtrlCh=10,BusyTime=34500,SkipGrp=0
[GroupChListInsert] Insert Grp Ch Idx=10,CenChannel=9,CtrlCh=11,BusyTime=1842,SkipGrp=0
[GroupChListInsert] Insert Grp Ch Idx=11,CenChannel=10,CtrlCh=12,BusyTime=14075,SkipGrp=1
[GroupChListInsert] Insert Grp Ch Idx=12,CenChannel=11,CtrlCh=13,BusyTime=14132,SkipGrp=1
Group Idx=0,control-Channle=1,cen-channel=255,Max-Busy-Time=19284
Group Idx=1,control-Channle=2,cen-channel=0,Max-Busy-Time=40286
Group Idx=2,control-Channle=3,cen-channel=1,Max-Busy-Time=40696
Group Idx=3,control-Channle=4,cen-channel=2,Max-Busy-Time=41001
Group Idx=4,control-Channle=5,cen-channel=3,Max-Busy-Time=41490
Group Idx=5,control-Channle=6,cen-channel=4,Max-Busy-Time=22061
Group Idx=6,control-Channle=7,cen-channel=5,Max-Busy-Time=43240
Group Idx=7,control-Channle=8,cen-channel=6,Max-Busy-Time=37621
Group Idx=8,control-Channle=9,cen-channel=7,Max-Busy-Time=34415
Group Idx=9,control-Channle=10,cen-channel=8,Max-Busy-Time=34500
Group Idx=10,control-Channle=11,cen-channel=9,Max-Busy-Time=1842
Min Busy Time=1842,select best ch 11
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
AsicSetRalinkBurstMode(4138): Not support for HIF_MT yet!
RTMPSetPiggyBack(876): Not support for HIF_MT yet!
AsicSetTxPreamble(4125): Not support for HIF_MT yet!
AsicAddSharedKeyEntry(1987): Not support for HIF_MT yet!
AsicAddSharedKeyEntry(1987): Not support for HIF_MT yet!
AsicAddSharedKeyEntry(1987): Not support for HIF_MT yet!
AsicAddSharedKeyEntry(1987): Not support for HIF_MT yet!
The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8
AsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xa0
Main bssid = d8:0d:17:bb:20:5a
<==== rt28xx_init, Status=0
@@@ ed_monitor_init : ===>
@@@ ed_monitor_init : <===
mt7603_set_ed_cca: TURN ON EDCCA mac 0x10618 = 0xd7c87d0f, EDCCA_Status=1
jiffies=ffff9aa5, POLLING_MODE_DETECT_INTV=300
WiFi Startup Cost (ra0): 7.310s
ifconfig used greatest stack depth: 12208 bytes left
Set_ed_chk_proc()::ed_chk=0
mt7603_set_ed_cca: TURN OFF EDCCA mac 0x10618 = 0xd7083f0f, EDCCA_Status=0
device ra0 entered promiscuous mode
br0: port 5(ra0) entering forwarding state
br0: port 5(ra0) entering forwarding state
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 90; error = Address already in use
igmpd# Err: setsockopt - MRT_ADD_VIF
device apcli0 entered promiscuous mode
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igdevice ra1 entered promiscuous mode
mpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 90; error = Address alreaddevice ra2 entered promiscuous mode
y in use
igmpd# Err: setsockopt - MRT_ADD_VIF
device ra3 entered promiscuous mode
Set_ed_chk_proc()::ed_chk=0
mt7603_set_ed_cca: TURN OFF EDCCA mac 0x10618 = 0xd7083f0f, EDCCA_Status=0
WLAN-Start wlNetlinkTool
Waiting for Wireless Events from interfaces...
swWlanChkAhbErr: netlink to do
rai0 no private ioctls.
The remaining IMEM space cannot accommodate section .imem_text !!
Remaining IMEM space: 732 bytes Section Size: 888 bytes
register rtpci
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
=== pAd = c2682000, size = 1541984 ===
<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xc2580000, csr_addr=0xc2580000!
device_id =0x7662
==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=rai
iptables: Chain already exists.
Chain EB_FORWARD_GUEST already exists.
OAL:Writefile 5GHz, WscConfigMethods:0x80
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
build time =
20141115060606a
rom patch for E3 IC
platform =
ALPS
hw/sw version =
ŠŠ
patch version =

FW Version:0.0.00 Build:1
Build Time:201607111443____
fw for E3 IC
==============eeFlashId: 30306 ====================
RX[0] DESC a40ca000 size = 8192
RX[1] DESC a40cc000 size = 8192
UserCfgInit(): MgmtRingFullTimes(0) init
proc_watch_dog_5G_init(): can create /proc/tplink/watch_dog_check_5G
proc_5G_alive_init(): can create /proc/tplink/wireless_5G_alive
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Not Equal!
APSDCapable[0]=1
APSDCapable[1]=1
APSDCapable[2]=1
APSDCapable[3]=1
APSDCapable[4]=1
APSDCapable[5]=1
APSDCapable[6]=1
APSDCapable[7]=1
APSDCapable[8]=1
APSDCapable[9]=1
APSDCapable[10]=1
APSDCapable[11]=1
APSDCapable[12]=1
APSDCapable[13]=1
APSDCapable[14]=1
APSDCapable[15]=1
default ApCliAPSDCapable[0]=1
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
APCli_WPAPSK_KEY, key string required 8 ~ 64 characters!!!
I/F(apcli0) Key1Str is Invalid key length!
I/F(apcli0) Key2Str is Invalid key length!
I/F(apcli0) Key3Str is Invalid key length!
I/F(apcli0) Key4Str is Invalid key length!
RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
NVM is FLASH mode (pAd->flash_offset = 0xff8000)
1. Phy Mode = 49
==============eeFlashId: 30306 ====================
get_chl_grp:illegal channel (167)
get_chl_grp:illegal channel (167)
get_chl_grp:illegal channel (169)
get_chl_grp:illegal channel (169)
get_chl_grp:illegal channel (171)
get_chl_grp:illegal channel (171)
/opt/bba/git-src/maxis/20200120/BBA1_0_Maxis_C5v/mtk/modules/private/wifi/MT7612E_LinuxAP_3.0.4.0.P1_DPA/os/linux/../../chips/mt76x2.c:2910 assert (ad->TxPower[choffset].Channel == 42)failed
Country Region from e2p = ffff
mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=1, temp_tx_alc_enable=1
mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=1
mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=14, low_temp_slope=9
mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0
mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=-7, tc_upper_bound=4
mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0
mt76x2_get_external_lna_gain::LNA type=0x1, BLNAGain=0xffffff8c, ALNAGain0=0xffffff8c, ALNAGain1=0xffffff8c, ALNAGain2=0xffffff8c
2. Phy Mode = 49
3. Phy Mode = 49
andes_pci_fw_init
0x1300 = 00073200
AntCfgInit: primary/secondary ant 0/1
andes_load_cr:cr_type(2)
ChipStructAssign(): MT76x2 hook !
RTMPSetPhyMode: channel is out of range, use first channel=0
MCS Set = ff ff 00 00 01
[BuildAcsScanChList] Support channel: PrimCh=36, CentCh=42, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=40, CentCh=42, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=44, CentCh=42, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=48, CentCh=42, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=52, CentCh=58, DFS=1, skip 0
[BuildAcsScanChList] Support channel: PrimCh=56, CentCh=58, DFS=1, skip 0
[BuildAcsScanChList] Support channel: PrimCh=60, CentCh=58, DFS=1, skip 0
[BuildAcsScanChList] Support channel: PrimCh=64, CentCh=58, DFS=1, skip 0
[BuildAcsScanChList] Support channel: PrimCh=149, CentCh=155, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=153, CentCh=155, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=157, CentCh=155, DFS=0, skip 0
[BuildAcsScanChList] Support channel: PrimCh=161, CentCh=155, DFS=0, skip 0
get_low_mid_hi_index:illegal channel(0)
get_low_mid_hi_index:illegal channel(0)
mt76x2_single_sku::sku_base_pwr = 0x1e, DefaultTargetPwr = 0x21, ch_pwr_adj = 0xfffffffd(-3), 0x13B4: 0x1b0f043d
get_low_mid_hi_index:illegal channel(0)
get_low_mid_hi_index:illegal channel(0)
mt76x2_single_sku::sku_base_pwr = 0x1e, DefaultTargetPwr = 0x21, ch_pwr_adj = 0xfffffffd(-3), 0x13B4: 0x1b0f043d
get_low_mid_hi_index:illegal channel(0)
get_low_mid_hi_index:illegal channel(0)
mt76x2_single_sku::sku_base_pwr = 0x1e, DefaultTargetPwr = 0x21, ch_pwr_adj = 0xfffffffd(-3), 0x13B4: 0x1b0f043d
get_low_mid_hi_index:illegal channel(0)
get_low_mid_hi_index:illegal channel(0)
mt76x2_single_sku::sku_base_pwr = 0x1e, DefaultTargetPwr = 0x21, ch_pwr_adj = 0xfffffffd(-3), 0x13B4: 0x1b0f043d
get_low_mid_hi_index:illegal channel(0)
get_low_mid_hi_index:illegal channel(0)
mt76x2_single_sku::sku_base_pwr = 0x1e, DefaultTargetPwr = 0x21, ch_pwr_adj = 0xfffffffd(-3), 0x13B4: 0x1b0f043d
get_low_mid_hi_index:illegal channel(0)
get_low_mid_hi_index:illegal channel(0)
mt76x2_single_sku::sku_base_pwr = 0x1e, DefaultTargetPwr = 0x21, ch_pwr_adj = 0xfffffffd(-3), 0x13B4: 0x1b0f043d
get_low_mid_hi_index:illegal channel(0)
get_low_mid_hi_index:illegal channel(0)
mt76x2_single_sku::sku_base_pwr = 0x1e, DefaultTargetPwr = 0x21, ch_pwr_adj = 0xfffffffd(-3), 0x13B4: 0x1b0f043d
get_low_mid_hi_index:illegal channel(0)
get_low_mid_hi_index:illegal channel(0)
mt76x2_single_sku::sku_base_pwr = 0x1e, DefaultTargetPwr = 0x21, ch_pwr_adj = 0xfffffffd(-3), 0x13B4: 0x1b0f043d
get_low_mid_hi_index:illegal channel(0)
get_low_mid_hi_index:illegal channel(0)
mt76x2_single_sku::sku_base_pwr = 0x1e, DefaultTargetPwr = 0x21, ch_pwr_adj = 0xfffffffd(-3), 0x13B4: 0x1b0f043d
get_low_mid_hi_index:illegal channel(0)
get_low_mid_hi_index:illegal channel(0)
mt76x2_single_sku::sku_base_pwr = 0x1e, DefaultTargetPwr = 0x21, ch_pwr_adj = 0xfffffffd(-3), 0x13B4: 0x1b0f043d
get_low_mid_hi_index:illegal channel(0)
get_low_mid_hi_index:illegal channel(0)
mt76x2_single_sku::sku_base_pwr = 0x1e, DefaultTargetPwr = 0x21, ch_pwr_adj = 0xfffffffd(-3), 0x13B4: 0x1b0f043d
get_low_mid_hi_index:illegal channel(0)
get_low_mid_hi_index:illegal channel(0)
mt76x2_single_sku::sku_base_pwr = 0x1e, DefaultTargetPwr = 0x21, ch_pwr_adj = 0xfffffffd(-3), 0x13B4: 0x1b0f043d
get_low_mid_hi_index:illegal channel(0)
get_low_mid_hi_index:illegal channel(0)
mt76x2_single_sku::sku_base_pwr = 0x1e, DefaultTargetPwr = 0x21, ch_pwr_adj = 0xfffffffd(-3), 0x13B4: 0x1b0f043d
GenerateGroupChannelList ChannelListNum=12
=====================================================
Channel 36 : Busy Time = 45, Score 100,Skip Channel = FALSE
=====================================================
Channel 40 : Busy Time = 1, Score 100,Skip Channel = FALSE
=====================================================
Channel 44 : Busy Time = 3, Score 100,Skip Channel = FALSE
=====================================================
Channel 48 : Busy Time = 13, Score 100,Skip Channel = FALSE
=====================================================
Channel 52 : Busy Time = 291, Score 100,Skip Channel = TRUE
=====================================================
Channel 56 : Busy Time = 1257, Score 99,Skip Channel = TRUE
=====================================================
Channel 60 : Busy Time = 1285, Score 99,Skip Channel = TRUE
=====================================================
Channel 64 : Busy Time = 2524, Score 98,Skip Channel = TRUE
=====================================================
Channel 149 : Busy Time = 2871, Score 98,Skip Channel = FALSE
=====================================================
Channel 153 : Busy Time = 3457, Score 97,Skip Channel = FALSE
=====================================================
Channel 157 : Busy Time = 3625, Score 97,Skip Channel = FALSE
=====================================================
Channel 161 : Busy Time = 3534, Score 97,Skip Channel = FALSE
=====================================================
GroupChListInsert Insert new group channel list Number=1 CenChannel=42 BestCtrlChannel=36 BUSY_TIEM=45, SkipGroup=0, GrpScore=100
GroupChListUpdate Update group channel list index=1 CenChannel=42 BestCtrlChannel=36 BUSY_TIEM=45 SkipGroup=0, GrpScore=100
GroupChListUpdate Update group channel list index=1 CenChannel=42 BestCtrlChannel=36 BUSY_TIEM=45 SkipGroup=0, GrpScore=100
GroupChListUpdate Update group channel list index=1 CenChannel=42 BestCtrlChannel=36 BUSY_TIEM=45 SkipGroup=0, GrpScore=100
GroupChListInsert Insert new group channel list Number=2 CenChannel=58 BestCtrlChannel=52 BUSY_TIEM=291, SkipGroup=1, GrpScore=100
GroupChListUpdate Update group channel list index=2 CenChannel=58 BestCtrlChannel=52 BUSY_TIEM=1257 SkipGroup=1, GrpScore=99
GroupChListUpdate Update group channel list index=2 CenChannel=58 BestCtrlChannel=52 BUSY_TIEM=1285 SkipGroup=1, GrpScore=99
GroupChListUpdate Update group channel list index=2 CenChannel=58 BestCtrlChannel=52 BUSY_TIEM=2524 SkipGroup=1, GrpScore=98
GroupChListInsert Insert new group channel list Number=3 CenChannel=155 BestCtrlChannel=149 BUSY_TIEM=2871, SkipGroup=0, GrpScore=98
GroupChListUpdate Update group channel list index=3 CenChannel=155 BestCtrlChannel=149 BUSY_TIEM=3457 SkipGroup=0, GrpScore=97
GroupChListUpdate Update group channel list index=3 CenChannel=155 BestCtrlChannel=149 BUSY_TIEM=3625 SkipGroup=0, GrpScore=97
GroupChListUpdate Update group channel list index=3 CenChannel=155 BestCtrlChannel=149 BUSY_TIEM=3625 SkipGroup=0, GrpScore=97
ChIdx=0 control-Channle=36 cen-channel=42
Max_BUSY_TIME=45
ChIdx=2 control-Channle=149 cen-channel=155
Max_BUSY_TIME=3625
@@@@@@@ final score is (ch36 : 100)
@@@@@@@ final score is (ch40 : 99)
@@@@@@@ final score is (ch44 : 98)
@@@@@@@ final score is (ch48 : 97)
@@@@@@@ final score is (ch52 : 100)
@@@@@@@ final score is (ch56 : 99)
@@@@@@@ final score is (ch60 : 98)
@@@@@@@ final score is (ch64 : 97)
@@@@@@@ final score is (ch149 : 100)
@@@@@@@ final score is (ch153 : 99)
@@@@@@@ final score is (ch157 : 98)
@@@@@@@ final score is (ch161 : 97)
CH0 is non-VHT80 capability!
@@@@@@@ final score is (ch165 : 100)
Min Busy 45 select best ch 36
mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42
mt76x2_single_sku::sku_base_pwr = 0x1c, DefaultTargetPwr = 0x21, ch_pwr_adj = 0xfffffffb(-5), 0x13B4: 0x1b0f043b
APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
mt76x2_calibration(channel = 42)
The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8
Main bssid = d8:0d:17:bb:20:5b
mt76x2_reinit_agc_gain:original agc_vga0 = 0x48, agc_vga1 = 0x48
mt76x2_reinit_agc_gain:updated agc_vga0 = 0x48, agc_vga1 = 0x48
mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x33, hi_lna1 = 0x33
mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x33, hi_lna1 = 0x33
original vga value(chain0) = 48
original vga value(chain1) = 48
<==== rt28xx_init, Status=0
get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=rai
get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=rai
get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=rai
get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=apclii
RTMPDrvOpen(1):Check if PDMA is idle!
RTMPDrvOpen(2):Check if PDMA is idle!
jiffies=ffff9fff, POLLING_MODE_DETECT_INTV=300
device rai0 entered promiscuous mode
br0: port 10(rai0) entering forwarding state
br0: port 10(rai0) entering forwarding state
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igmpd#device apclii0 entered promiscuous mode
Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address alreadydevice rai1 entered promiscuous mode
in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 90; errdevice rai2 entered promiscuous mode
or = Address already in use
igmpd# Err: setsockopt - MRT_ADD_VIF
igmpd# file: src/igmp_ifinfodevice rai3 entered promiscuous mode
.c;line: 123; error = Address already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 90; error = Address already in use
igmpd# Err: setsockopt - MRT_ADD_VIF
wlNetlinkTool is already there.
sendto /var/tmp/8 msg 2030 error No such file or directory ,pid 438
sendto /var/tmp/8 msg 2030 error No such file or directory ,pid 438
sendto /var/tmp/8 msg 2030 error No such file or directory ,pid 438
sendto /var/tmp/8 msg 2030 error No such file or directory ,pid 438
sendto /var/tmp/8 msg 2030 error No such file or directory ,pid 438
sendto /var/tmp/8 msg 2030 error No such file or directory ,pid 438
sendto /var/tmp/8 msg 2030 error No such file or directory ,pid 438
sendto /var/tmp/8 msg 2030 error No such file or directory ,pid 438
sendto /var/tmp/8 msg 2030 error No such file or directory ,pid 438
sendto /var/tmp/8 msg 2030 error No such file or directory ,pid 438
sendto /var/tmp/8 msg 2030 error No such file or directory ,pid 438
sendto /var/tmp/9 msg 2004 error No such file or directory ,pid 438
killall: dnsmasq: no process killed
open lock file error!
open lock file error!
qos_wrr_info: 0 0 0 0 0
QDMA QoS: HW SP
iptables: Bad rule (does a matching rule exist in that chain?).
[ rsl_initLanHostCfgObj ] 765: error alloc client account share memory
radvd starting
usage: dhcp6s [-c configfile] [-dDf] [-k ctlkeyfile] [-p ctlport] [-P pidfile] intface
radvd starting
[Jan 01 08:00:59] radvd: syntax error in /var/tmp/dconf/radvd_.conf, line 2: {
[Jan 01 08:00:59] radvd: error parsing or activating the config file: /var/tmp/dconf/radvd_.conf
ifconfig: up: error fetching interface information: Device not found
ifconfig: up: error fetching interface information: Device not found
device nas10 entered promiscuous mode
==>Error, socket or ioctl error for mulifctl
==>Error, socket or ioctl error for mulifctl
==>Error, socket or ioctl error for mulifctl
==>Error, socket or ioctl error for mulifctl
==>Error, socket or ioctl error for mulifctl
==>Error, socket or ioctl error for mulifctl
==>Error, socket or ioctl error for mulifctl
[ getPidFromPidFile ] 112: Cann't open file: /var/run/zebra.pid.
[ getPidFromPidFile ] 112: Cann't open file: /var/run/ripd.pid.
[ read_dhcpc_config ] 113: error, unable to open config file: /var/tmp/dconf/udhcpc.conf
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
ip6tables: Bad rule (does a matching rule exist in that chain?).
ip6tables: Bad rule (does a matching rule exist in that chain?).
ip6tables: Bad rule (does a matching rule exist in that chain?).
[ rsl_setStorageServiceObj ] 1252: mountFlag is 3,We start usb server
killall: ushare: no process killed
pid 1468's current affinity mask: 4
pid 1468's new affinity mask: 4
cat: can't open '/dev/voip': No such device or address
pid 435's current affinity mask: 4
pid 435's new affinity mask: 4
[EVA ERROR]dspConfigToneMtk(2114)- EXIT toneId=0
sendto /var/tmp/25 msg 2000 error Resource temporarily unavailable ,pid 1468
auto_level_control_set <cid:0> <enable:1> <up shift gain:6> <down shift gain:6> <reference Gain:25> <threshold:45> <Noise threshold:40> <Delta threshold:3>
auto_level_control_set <cid:1> <enable:1> <up shift gain:6> <down shift gain:6> <reference Gain:25> <threshold:45> <Noise threshold:40> <Delta threshold:3>
uShare (version 1.1a), a lightweight UPnP A/V and DLNA Media Server.
Benjamin Zores (C) 2005-2007, for GeeXboX Team.
See http://ushare.geexbox.org/ for updates.
usbcore: registered new interface driver usblp
[ rsl_initXTtConfSmtpObj ] 1929: SMTP Server 0.0.0.0 error.
/bin/sh: can't create /proc/tplink/local_domain_name: nonexistent directory
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
#file: src/http_init.c;line: 941; error = No such file or directory
#msg: Invalid msg type!
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables v1.4.17: Couldn't find target `REJECT_WITH_CHAIN'
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
Sorry, rule does not exist.
Enable forward!
starting pid 442, tty '': '/sbin/getty -L ttyS0 115200 vt100'
Archer C5v login: root
Password:
Login incorrect
Archer C5v login: admin
Password:
Login incorrect
Archer C5v login: administrator
Password:
Login incorr
process '/sbin/getty -L ttyS0 115200 vt100' (pid 442) exited. Scheduling for restart.
Please press Enter to activate this console. usb 1-2: new high speed USB device number 2 using xhc_mtk
scsi0 : usb-storage 1-2:1.0
hotplug_storage.c#hotplug_3g(1429): pid 1783: pPlugDevId[0]=19d2_1225_1234567890ABCDEF, plugDevClass[0]=unswitched_3g, plugAction[0]=add
hotplug_storage.c#hotplugLedCtrl(268): -------------ledNum(2), status(2)-----------
hotplug_storage.c#hotplug_3g(1505): handle_card -a called.
scsi 0:0:0:0: CD-ROM ZTE USB SCSI CD-ROM 2.31 PQ: 0 ANSI: 2
scsi 0:0:0:1: Direct-Access ZTE MMC Storage 2.31 PQ: 0 ANSI: 2
sd 0:0:0:1: [sda] call sd_media_changed(), set sdkp->media_present to 1
sd 0:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 0:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 0:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 0:0:0:1: [sda] media is not present, wait for 0.5 seconds
opt=0, manual=0, vendor=0x19d2, proid=0x1225, cmd is
[ usb3gHandleEventHandler ] 4284: *******MODEM_HANDLING**********
prep_switch 342: dir----"."
prep_switch 342: dir----".."
prep_switch 342: dir----"002"
prep_switch 357: find device bus dir----/proc/bus/usb/002/
prep_switch 368: dir----"."
prep_switch 368: dir----".."
prep_switch 368: dir----"001"
prep_switch 342: dir----"001"
prep_switch 357: find device bus dir----/proc/bus/usb/001/
prep_switch 3Erase from 0xfe0000 with 0x2b71 bytes, mtd->erasesize 0x10000
erase addr=fe0000 size=1000068: dir----"."
prep_switch 368: dir----".."
prep_switch 368: dir----"002"
prep_switch 388: find device file index = 0, name = /proc/bus/usb/001/002
prep_switch 368: dir----"001"
prep_switch 342: dir----"devices"
prep_switch 405: reset device----index = 0, name = /proc/bus/usb/001/002
Resetting USB device /proc/bus/usb/001/002
.
Write to flash:0xfe0000, len is 0x2b71
posix_timer_do: 107 callbacks suppressed
usb 1-2: reset high speed USB device number 2 using xhc_mtk
xhc_mtk xhc_mtk: xHCI xhci_drop_endpoint called with disabled ep 8411b32c
xhc_mtk xhc_mtk: xHCI xhci_drop_endpoint called with disabled ep 8411b300
Reset successful
sd 0:0:0:1: [sda] call sd_media_changed(), set sdkp->media_present to 1
sd 0:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 0:0:0:1: [sda] media is not present, wait for 0.5 seconds
card_add 192
Start get card info, vid=19d2, pid=1225
get_card_info 90 dev->descriptor.idVendor = 0x19d2, dev->descriptor.idProduct = 0x1225
get_card_info 114 dev->descriptor.bNumConfigurations = 1
get_card_info 149 usbCinfo[0].idVendor = 0x19d2, usbCinfo[0].idProduct = 0x1225
get_card_info 90 dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x2
get_card_info 109 ZQQ dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x2
get_card_info 90 dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x3
get_card_info 1sd 0:0:0:1: [sda] media is not present, wait for 0.5 seconds
09 ZQQ dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x3
get_card_info 214 index = 1
get_card_info 274 cinfo->idVendor = 0x19d2, cinfo->idProduct = 0x1225
get_cinfo_ata, 375: OK, the device still has the same vid and pid.
sd 0:0:0:1: [sda] media is not present, wait for 0.5 seconds
print_cinfo 62 pro=1225, vendor=19d2, index=-1
Interface 0, type is 8
print_cinfo 62 pro=1225, vendor=19d2, index=-1
Interface 0, type is 8
can't switch usb device
sd 0:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 0:0:0:1: [sda] media is not present, wait for 0.5 seconds
getConfigFromMergeFile 150 decrypt mode_switch.conf successfully
getConfigFromMergeFile 162 pid = 0x1225, vid = 0x19d2
search start keyword :[start_19d2_1225
search end keyword :[end_19d2_1225
save cfg file @/var/3G/19d2_1225_0
save cfg file @/var/3G/19d2_1225_1
total =2
345 cfgFilePath = /var/3G/19d2_1225_0
modeSwitchByCfgFile 541 cmd = usb_modeswitch -v 0x19d2 -p 0x1225 -I -W -c /var/3G/19d2_1225_0 &
Start find usb_modeswitch
Reading config file: /var/3G/19d2_1225_0
* usb_modeswitch: handle USB devices with multiple modes
* Version 1.2.3 (C) Josua Dietze 2012
* Based on libusb0 (0.1.12 and above)
! PLEASE REPORT NEW CONFIGURATIONS !
DefaultVendor= 0x19d2
DefaultProduct= 0x1225
TargetVendor= not set
TargetProduct= not set
TargetClass= not set
TargetProductList=""
DetachStorageOnly=0
HuaweiMode=0
SierraMode=0
SonyMode=0
QisdaMode=0
GCTMode=0
KobilMode=0
SequansMode=0
MobileActionMode=0
CiscoMode=0
MessageEndpoint= not set
MessageContent="5553424312345678000000000000061e000000000000000000000000000000"
MessageContent2="5553424312345679000000000000061b000000020000000000000000000000"
MessageContent3="55534243123456702000000080000c85010101180101010101000000000000"
NeedResponse=1
ResponseEndpoint= not set
InquireDevice disabled
Success check enabled, max. wait time 20 seconds
System integration mode disabled
Note: target parameter missing; success check limited
Looking for default devices ...
searching devices, found USB ID 19d2:1225
found matching vendor ID
found matching product ID
adding device
searching devices, found USB ID 1d6b:0002
searching devices, found USB ID 1d6b:0003
Found device in default mode, class or configuration (1)
Accessing device 002 on bus 001 ...
Getting the current device configuration ...
OK, got current device configuration (1)
Using first interface: 0x00
Using endpoints 0x01 (out) and 0x81 (in)
USB description data (for identification)
-------------------------
Manufacturer: ZTE,Incorporated
Product: ZTE Mobile Broadband
Serial No.: 1234567890ABCDEF
-------------------------
Looking for active driver ...
OK, driver found; name unknown, limitation of libusb1
usb 1-2: USB disconnect, device number 2
sd 0:0:0:1: [sda] call sd_media_changed(), set sdkp->media_present to 1
sd 0:0:0:1: [sda] Attached SCSI removable disk
OK, driver "unkown" detached
Setting up communication with interface 0
Could not claim interface (error -6). Skipping message sending
Checking for mode switch (max. 20 times, once per second) ...
usb 1-2: new high speed USB device number 3 using xhc_mtk
Starscsi1 : usb-storage 1-2:1.2
t find usb_modeswitch
kill 1823Start get card info, vid=19d2, pid=1225
get_card_info 90 dev->descriptor.idVendor = 0x19d2, dev->descriptor.idProduct = 0x1405
Couldn't open device, some information will be missing
get_card_info 90 dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x2
get_card_info 109 ZQQ dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x2
get_card_info 90 dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x3
get_card_info 109 ZQQ dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x3
scsi 1:0:0:0: CD-ROM ZTE USB SCSI CD-ROM 2.31 PQ: 0 ANSI: 2
In switch judgemenscsi 1:0:0:1: Direct-Access ZTE MMC Storage 2.31 PQ: 0 ANSI: 2
t, get card info error, maybe usb_modeswitch.
hotplug_storage.c#hotplugLedCtrl(268): -------------ledNum(2), status(1)-----------
[ usb3gHandleEventHandler ] 4258: *******MODEM_UNLINK**********
Erase from 0xfe0000 with 0x2b5a bytes, mtd->erasesize 0x10000
erase addr=fe0000 size=10000
sd 1:0:0:1: [sda] call sd_media_changed(), set sdkp->media_present to 1
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
.
Write to flash:0xfe0000, len is 0x2b5a
.
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
hotplug_storage.c#hotplug_3g(1429): pid 1784: pPlugDevId[0]=19d2_1225_1234567890ABCDEF, plugDevClass[0]=unswitched_3g, plugAction[0]=remove
hotplug_storage.c#hotplug_3g(1429): pid 1784: pPlugDevId[1]=19d2_1405_1234567890ABCDEF, plugDevClass[1]=switched_3g, plugAction[1]=add
hotplug_storage.c#hotplugLedCtrl(268): -------------ledNum(2), status(2)-----------
hotplug_storage.c#hotplug_3g(1505): handle_card -a called.
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
opt=0, manual=0, vendor=0x19d2, proid=0x1405, cmd is
[ usb3gHandleEventHandler ] 4284: *******MODEM_HANDLING**********
prep_switch 342: dir----"."
prep_switch 342: dir----".."
prep_switch 342: dir----"002"
prep_switch 357: find device bus dir----/proc/bus/usb/002/
prep_switch 368: dir----"."
prep_switch 368: dir----".."
prep_switch 368: dir----"001"
prep_switch 342: dir----"001"
prep_switch 357: find device bus dir----/proc/bus/usb/001/
prep_switch 368: dir----"."
prep_switch 368: dir----".."
preErase from 0xfe0000 with 0x2b5a bytes, mtd->erasesize 0x10000
erase addr=fe0000 size=10000p_switch 368: dir----"003"
prep_switch 388: find device file index = 0, name = /proc/bus/usb/001/003
prep_switch 368: dir----"001"
prep_switch 342: dir----"devices"
prep_switch 405: reset device----index = 0, name = /proc/bus/usb/001/003
Resetting USB device /proc/bus/usb/001/003
.
Write to flash:0xfe0000, len is 0x2b5a
posix_timer_do: 27 callbacks suppressed
.
usb 1-2: reset high speed USB device number 3 using xhc_mtk
xhc_mtk xhc_mtk: xHCI xhci_drop_endpoint called with disabled ep 8342012c
xhc_mtk xhc_mtk: xHCI xhci_drop_endpoint called with disabled ep 83420200
xhc_mtk xhc_mtk: xHCI xhci_drop_endpoint called with disabled ep 83420100
Reset successfulsd 1:0:0:1: [sda] call sd_media_changed(), set sdkp->media_present to 1
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
card_add 192
Start get card info, vid=19d2, pid=1405
get_card_info 90 dev->descriptor.idVendor = 0x19d2, dev->descriptor.idProduct = 0x1405
get_card_info 114 dev->descriptor.bNumConfigurations = 1
get_card_info 149 usbCinfo[0].idVendor = 0x19d2, usbCinfo[0].idProduct = 0x1405
get_card_info 90 dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x2
get_card_info 109 ZQQ devsd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x2
get_card_info 90 dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x3
get_card_info 109 ZQQ dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x3
get_card_info 214 index = 1
get_card_info 274 cinfo->idVendor = 0x19d2, cinfo->idProduct = 0x1405
get_cinfo_ata, 375: OK, the device still has the same vid and pid.
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
print_cinfo 62 pro=1405, vendor=19d2, index=0
Interface 0, type is 2
Interface 1, type is 10
Interface 2, type is 8
print_cinfo 62 pro=1405, vendor=19d2, index=0
Interface 0, type is 2
Interface 1, type is 10
Interface 2, type is 8
card_add 247: goto already_switched
card_add 468 already_switched
Start get card info, vid=19d2, pid=1405
get_cardsd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
_info 90 dev->descriptor.idVendor = 0x19d2, dev->descriptor.idProduct = 0x1405
get_card_info 114 dev->descriptor.bNumConfigurations = 1
get_card_info 149 usbCinfo[0].idVendor = 0x19d2, usbCinfo[0].idProduct = 0x1405
get_card_info 90 dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x2
get_card_info 109 ZQQ dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x2
get_card_info 90 dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x3
get_card_info 109 ZQQ dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x3
get_card_info 214 index = 1
get_card_info 274 cinfo->idVendor = 0x19d2, cinfo->idProduct = 0x1405
get_cinfo_ata, 375: OK, the device still has the same vid and pid.
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
Start get card info, vid=19d2, pid=1405
get_card_info 90 dev->descriptor.idVendor = 0x19d2, dev->descriptor.idProduct = 0x1405
get_card_info 114 dev->descriptor.bNumConfigurations = 1
get_card_info 149 usbCinfo[0].idVendor = 0x19d2, usbCinfo[0].idProduct = 0x1405
get_card_info 90 dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x2
get_card_info 109 ZQQ dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x2
get_card_info 90 dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x3
get_card_info 109 ZQQ dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x3
get_card_info 214 index = 1
get_card_info 274 cinfo->idVendor = 0x19d2, cinfo->idProductsd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
= 0x1405
get_cinfo_ata, 375: OK, the device still has the same vid and pid.
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] Attached SCSI removable disk
[ processAddUsbStorMsg ] 332: phyMediumObj.name same as pUsbStorMsg->name
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver rndis_host
Failed to to open /proc/tty/driver/usbserial
Start get card info, vid=19d2, pid=1405
get_card_info 90 dev->descriptor.idVendor = 0x19d2, dev->descriptor.idProduct = 0x1405
get_card_info 114 dev->descriptor.bNumConfigurations = 1
get_card_info 149 usbCinfo[0].idVendor = 0x19d2, usbCinfo[0].idProduct = 0x1405
get_card_info 90 dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x2
get_card_info 109 ZQQ dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x2
get_card_info 90 dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x3
get_card_info 109 ZQQ dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x3
get_card_info 214 index = 1
get_card_info 274 cinfo->idVendor = 0x19d2, cinfo->idProduct = 0x1405
get_cinfo_ata, 375: OK, the device still has the same vid and pid.
Start get card info, vid=19d2, pid=1405
get_card_info 90 dev->descriptor.idVendor = 0x19d2, dev->descriptor.idProduct = 0x1405
get_card_info 114 dev->descriptor.bNumConfigurations = 1
get_card_info 149 usbCinfo[0].idVendor = 0x19d2, usbCinfo[0].idProduct = 0x1405
get_card_info 90 dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x2
get_card_info 109 ZQQ dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x2
get_card_info 90 dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x3
get_card_info 109 ZQQ dev->descriptor.idVendor = 0x1d6b, dev->descriptor.idProduct = 0x3
get_card_info 214 index = 1
get_card_info 274 cinfo->idVendor = 0x19d2, cinfo->idProduct = 0x1405
get_cinfo_ata, 375: OK, the device still has the same vid and pid.
[ usb3gHandleEventHandler ] 4291: *******MODEM_LINK***deviceName: ttyNotReady, modemName: 3G Modem, ifNumber: 0**********
[ usb3gHandleEventHandler ] 4294: *******lteDeviceName: ETHER_MODEM****************
hotplug_storage.c#hotplugLedCtrl(268): -------------ledNum(2), status(1)-----------
hotplug_storage.c#hotplug_3g(1623): handle_card successfully, updateAttachedDevsFile.
Erase from 0xfe0000 with 0x2b71 bytes, mtd->erasesize 0x10000
erase addr=fe0000 size=10000
posix_timer_do: 9 callbacks suppressed
.
Write to flash:0xfe0000, len is 0x2b71
[ getPidFromPidFile ] 112: Cann't open file: /var/run/ripd.pid.
[ oal_lte_initDhcp ] 141: The LTE device name is ETHER_MODEM .
get error CMSG_TYPE!
====usbp umount===argc 2
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
====usbp mount===argc 2
iptables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: No chain/target/match by that name.
iptables: Bad rule (does a matching rule exist in that chain?).
get error CMSG_TYPE!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
[ processKerRouteMsg ] 241: L3ForwardingEntry is Exist
[ processKerRouteMsg ] 241: L3ForwardingEntry is Exist
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
pid 2035's current affinity mask: 4
pid 2035's new affinity mask: 8
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
====usbp====return 0@1600888783
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] media is not present, wait for 0.5 seconds
sd 1:0:0:1: [sda] we have tried 10 times, but the USB device is still not ready, just return here!
====usbp====return 0@1600888866
hotplug_storage.c#hotplugLedCtrl(268): -------------ledNum(2), status(1)-----------
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment