btt_octopus_pin_aliases.cfg

#####################################################################
#   BTT Octopus Pin Aliases
# See https://github.com/VoronDesign/VoronUsers/tree/master/firmware_configurations/klipper/revnull/btt_octopus_pins
#####################################################################

[board_pins]
aliases:
  # Stepper drivers
  MOT0_EN=PF14, MOT0_STEP=PF13, MOT0_DIR=PF12, MOT0_CS=PC4,   # MOTOR0
  MOT1_EN=PF15, MOT1_STEP=PG0,  MOT1_DIR=PG1,  MOT1_CS=PD11,  # MOTOR1
  MOT2_EN=PG5,  MOT2_STEP=PF11, MOT2_DIR=PG3,  MOT2_CS=PC6,   # MOTOR2
  MOT3_EN=PA0,  MOT3_STEP=PG4,  MOT3_DIR=PC1,  MOT3_CS=PC7,   # MOTOR3
  MOT4_EN=PG2,  MOT4_STEP=PF9,  MOT4_DIR=PF10, MOT4_CS=PF2,   # MOTOR4
  MOT5_EN=PF1,  MOT5_STEP=PC13, MOT5_DIR=PF0,  MOT5_CS=PE4,   # MOTOR5
  MOT6_EN=PD4,  MOT6_STEP=PE2,  MOT6_DIR=PE3,  MOT6_CS=PE1,   # MOTOR6
  MOT7_EN=PE0,  MOT7_STEP=PE6,  MOT7_DIR=PA14, MOT7_CS=PD3,   # MOTOR7

  # Heaters
  BED_OUT=PA1,
  HE0=PA2, HE1=PA3, HE2=PB10, HE3=PB11,

  # Thermisors
  TB=PF3, T0=PF4, T1=PF5, T2=PF6, T3=PF7,
  PT100=PF8,

  # Fans
  FAN0=PA8, FAN1=PE5, FAN2=PD12, FAN3=PD13, FAN4=PD14, FAN5=PD15,

  # End stops
  ESTOP0=PG6,  ESTOP1=PG9,  ESTOP2=PG10, ESTOP3=PG11,
  ESTOP4=PG12, ESTOP5=PG13, ESTOP6=PG14, ESTOP7=PG15,

  # EXP1
  EXP1_1=PE8,   EXP1_2=PE7,
  EXP1_3=PE9,   EXP1_4=PE10,
  EXP1_5=PE12,  EXP1_6=PE13,    # Slot in the socket on this side
  EXP1_7=PE14,  EXP1_8=PE15,
  EXP1_9=<GND>, EXP1_10=<5V>,

  # EXP2
  EXP2_1=PA6,   EXP2_2=PA5,
  EXP2_3=PB1,   EXP2_4=PA4,
  EXP2_5=PB2,   EXP2_6=PA7,     # Slot in the socket on this side
  EXP2_7=PC15,  EXP2_8=<RST>,
  EXP2_9=<GND>, EXP2_10=PC5,

  # TFT
  TFT_5=<RST>,
  TFT_4=PA10,
  TFT_3=PA9,
  TFT_2=<GND>,
  TFT_1=<5V>,

  # Inductive Probe
  PRB_1=<DCV>, PRB_2=<GND>, PRB_3=PB7,

  # BL Touch
  BLT_5=<GND>,
  BLT_4=<5V>,
  BLT_CTL=PB6,   # BL Touch servo pin
  BLT_2=<GND>,
  BLT_SNSR=PB7,  # BL Touch end stop pin

  # LED Control
  NEOPXL_3=<GND>, NEOPXL_2=PB0, NEOPXL_1=<5V>,

  # Raspberry Pi
  RPI_1=<5V>,  RPI_2=<5V>,
  RPI_3=<GND>, RPI_4=<GND>,
  RPI_5=<GND>, RPI_6=<GND>,
  RPI_7=<GND>, RPI_8=<GND>,
  RPI_RX=PD6,  RPI_TX=PD5,

  # SPI3
  SPI3_2=<3V3>, SPI3_MOSI=PB5, SPI3_CS=PA15, SPI3_8=<GND>, SPI3_10=<5V>,
  SPI3_1=<GND>, SPI3_MISO=PB4, SPI3_SCK=PB3, SPI3_7=<GND>, SPI3_9=<5V>,

  # Other headers
  POWER_DET=PC0,
  PS_ON=PE11

display.cfg

[display]
lcd_type: uc1701
cs_pin: EXP1_3 # LCD_CS
a0_pin: EXP1_4 # LCD_RS
rst_pin: EXP1_5 # LCD_RST
contrast: 63
encoder_pins: ^EXP2_5, ^EXP2_3 # ENC_B, ENC_A
click_pin: ^!EXP1_2 # ENC_BTN
spi_software_miso_pin: EXP2_1 # MISO
spi_software_mosi_pin: EXP2_6 # MOSI
spi_software_sclk_pin: EXP2_2 # CLK

# [output_pin beeper]
# pin: EXP1_1
# pwm: True
# cycle_time: 0.005 # 5kHz

[neopixel btt_mini12864]
pin: EXP1_6
chain_count: 3
color_order: RGB
initial_RED: 0.4
initial_GREEN: 0.4
initial_BLUE: 0.4

# [delayed_gcode setdisplayneopixel]
# initial_duration: 3
# gcode:
#   SET_LED LED=btt_mini12864 RED=0 GREEN=0 BLUE=0 INDEX=1 TRANSMIT=0
#   SET_LED LED=btt_mini12864 RED=0 GREEN=0 BLUE=1 INDEX=2 TRANSMIT=0
#   SET_LED LED=btt_mini12864 RED=0 GREEN=1 BLUE=0 INDEX=3

[menu __main __octoprint]
type: disabled