Skip to content

Instantly share code, notes, and snippets.

@ChimeraCoder
Created November 1, 2013 16:47
Show Gist options
  • Star 0 You must be signed in to star a gist
  • Fork 0 You must be signed in to fork a gist
  • Save ChimeraCoder/04c05b8750c165c20082 to your computer and use it in GitHub Desktop.
Save ChimeraCoder/04c05b8750c165c20082 to your computer and use it in GitHub Desktop.
[ 10.296636] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 10.325238] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
[ 10.332150] iwlwifi 0000:02:00.0: Radio type=0x1-0x2-0x0
[ 10.393359] init: gdm main process (1149) killed by TERM signal
[ 10.626023] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
[ 10.632890] iwlwifi 0000:02:00.0: Radio type=0x1-0x2-0x0
[ 10.741557] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 10.742000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 10.770455] Adding 3905532k swap on /dev/mapper/cryptswap1. Priority:-1 extents:1 across:3905532k SS
[ 10.834852] [drm:gen6_sanitize_pm] *ERROR* Power management discrepancy: GEN6_RP_INTERRUPT_LIMITS expected 18000000, was 12060000
[ 11.144510] postgres (1503): /proc/1503/oom_adj is deprecated, please use /proc/1503/oom_score_adj instead.
[ 12.406475] cfg80211: Found new beacon on frequency: 5180 MHz (Ch 36) on phy0
[ 12.716074] cfg80211: Found new beacon on frequency: 5220 MHz (Ch 44) on phy0
[ 13.183676] init: plymouth-stop pre-start process (1894) terminated with status 1
[ 14.614773] cfg80211: Found new beacon on frequency: 5745 MHz (Ch 149) on phy0
[ 14.847207] cfg80211: Found new beacon on frequency: 5785 MHz (Ch 157) on phy0
[ 18.072975] wlan0: authenticate with 00:1a:1e:74:67:30 (try 1)
[ 18.269043] wlan0: authenticate with 00:1a:1e:74:67:30 (try 2)
[ 18.270170] wlan0: authenticated
[ 18.277456] wlan0: associate with 00:1a:1e:74:67:30 (try 1)
[ 18.476779] wlan0: associate with 00:1a:1e:74:67:30 (try 2)
[ 18.478650] wlan0: RX AssocResp from 00:1a:1e:74:67:30 (capab=0x401 status=0 aid=1)
[ 18.478654] wlan0: associated
[ 18.483223] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 29.304267] wlan0: no IPv6 routers present
[ 46.109556] iwlwifi 0000:02:00.0: Tx aggregation enabled on ra = 00:1a:1e:74:67:30 tid = 0
[ 267.385275] [drm:gen6_sanitize_pm] *ERROR* Power management discrepancy: GEN6_RP_INTERRUPT_LIMITS expected 18070000, was 18000000
[ 437.409724] wlan0: direct probe to 00:1a:1e:74:70:f0 (try 1/3)
[ 437.609449] wlan0: direct probe to 00:1a:1e:74:70:f0 (try 2/3)
[ 437.809133] wlan0: direct probe to 00:1a:1e:74:70:f0 (try 3/3)
[ 437.893264] cfg80211: All devices are disconnected, going to restore regulatory settings
[ 437.893280] cfg80211: Restoring regulatory settings
[ 437.893291] cfg80211: Calling CRDA to update world regulatory domain
[ 437.901694] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
[ 437.901704] cfg80211: World regulatory domain updated:
[ 437.901708] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 437.901715] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 437.901720] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 437.901725] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 437.901730] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 437.901735] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 438.008908] wlan0: direct probe to 00:1a:1e:74:70:f0 timed out
[ 445.935873] cfg80211: Found new beacon on frequency: 5805 MHz (Ch 161) on phy0
[ 446.075311] wlan0: authenticate with 00:1a:1e:74:71:f0 (try 1)
[ 446.275033] wlan0: authenticate with 00:1a:1e:74:71:f0 (try 2)
[ 446.276217] wlan0: authenticated
[ 446.285689] wlan0: associate with 00:1a:1e:74:71:f0 (try 1)
[ 446.482838] wlan0: associate with 00:1a:1e:74:71:f0 (try 2)
[ 446.484800] wlan0: RX ReassocResp from 00:1a:1e:74:71:f0 (capab=0x401 status=0 aid=6)
[ 446.484811] wlan0: associated
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment