Sapphire Pro settings

Cura settings

PK!ÌÒB
B
custom_.4mm[general]
version = 4
name = .4mm
definition = fdmprinter

[metadata]
type = quality_changes
quality_type = draft
setting_version = 16

[values]
adhesion_type = skirt
bridge_settings_enabled = False
layer_height = 0.4
layer_height_0 = 0.3
material_bed_temperature = 70
speed_slowdown_layers = 1
support_type = everywhere

PK!H}Ê55custom_extruder_1_#2_.4mm[general]
version = 4
name = .4mm
definition = fdmprinter

[metadata]
type = quality_changes
position = 0
intent_category = default
quality_type = draft
setting_version = 16

[values]
bottom_layers = 3
brim_outside_only = False
brim_width = 5
fill_outline_gaps = True
infill_pattern = gyroid
infill_sparse_density = 15
material_final_print_temperature = 220
material_initial_print_temperature = 220
material_print_temperature = 220
optimize_wall_printing_order = True
retraction_amount = 1
retraction_enable = False
roofing_layer_count = 1
skin_overlap = 50
skirt_gap = 5
skirt_line_count = 5
speed_equalize_flow_enabled = True
speed_print = 50
speed_roofing = 25
speed_topbottom = 25
speed_travel = 50
speed_travel_layer_0 = 25
speed_wall = 50
speed_wall_x = 50
support_bottom_enable = False
support_brim_enable = True
support_conical_enabled = True
support_conical_min_width = 10
support_infill_rate = 10
support_roof_height = 0.8
support_xy_distance = 1.0
support_z_distance = 0.2
top_bottom_pattern = zigzag
top_layers = 3
travel_avoid_supports = True
wall_line_count = 3

PK
!ÌÒB
B
€
custom_.4mmPK
!H}Ê55€
k
custom_extruder_1_#2_.4mmPK€×

Marlin Version and EEPROM

FIRMWARE_NAME:Marlin 2.0.7.2 (Feb 22 2021 19:43:43)

Send: M503
Recv: echo:  G21    ; Units in mm (mm)
Recv: echo:  M149 C ; Units in Celsius
Recv: 
Recv: echo:; Filament settings: Disabled
Recv: echo:  M200 S0 D1.75
Recv: echo:; Steps per unit:
Recv: echo: M92 X80.00 Y80.00 Z1600.00 E425.00
Recv: echo:; Maximum feedrates (units/s):
Recv: echo:  M203 X300.00 Y300.00 Z10.00 E50.00
Recv: echo:; Maximum Acceleration (units/s2):
Recv: echo:  M201 X3000.00 Y3000.00 Z100.00 E10000.00
Recv: echo:; Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel>
Recv: echo:  M204 P1000.00 R2000.00 T1500.00
Recv: echo:; Advanced: B<min_segment_time_us> S<min_feedrate> T<min_travel_feedrate> J<junc_dev>
Recv: echo:  M205 B20000.00 S0.00 T0.00 J0.01
Recv: echo:; Home offset:
Recv: echo:  M206 X0.00 Y0.00 Z0.00
Recv: echo:; Auto Bed Leveling:
Recv: echo:  M420 S0 Z0.00
Recv: echo:  G29 W I0 J0 Z0.16138
Recv: echo:  G29 W I1 J0 Z0.04625
Recv: echo:  G29 W I2 J0 Z0.06038
Recv: echo:  G29 W I0 J1 Z0.06575
Recv: echo:  G29 W I1 J1 Z0.01025
Recv: echo:  G29 W I2 J1 Z-0.00062
Recv: echo:  G29 W I0 J2 Z0.16163
Recv: echo:  G29 W I1 J2 Z0.06625
Recv: echo:  G29 W I2 J2 Z0.06350
Recv: echo:; Material heatup parameters:
Recv: echo:  M145 S0 H220 B70 F0
Recv: echo:  M145 S1 H240 B110 F0
Recv: echo:; PID settings:
Recv: echo:  M301 P14.21 I0.88 D57.26
Recv: echo:  M304 P21.37 I3.29 D92.53
Recv: echo:; Z-Probe Offset (mm):
Recv: echo:  M851 X16.00 Y-50.00 Z-0.90
Recv: echo:; Stepper driver current:
Recv: echo:  M906 X500 Y500 Z500
Recv: echo:  M906 T0 E500
Recv: 
Recv: echo:; Driver stepping mode:
Recv: echo:  M569 S1 X Y Z
Recv: echo:; Linear Advance:
Recv: echo:  M900 K0.03
Recv: echo:; Filament load/unload lengths:
Recv: echo:  M603 L150.00 U150.00
Recv: echo:; Backlash compensation:
Recv: echo:  M425 F0.00 X0.00 Y0.00 Z0.00
Recv: echo:; Filament runout sensor:
Recv: echo:  M412 S1