Created
February 21, 2014 09:45
-
-
Save Cylindric/9131485 to your computer and use it in GitHub Desktop.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
[profile] | |
layer_height = 0.2 | |
wall_thickness = 1 | |
retraction_enable = True | |
solid_layer_thickness = 0.6 | |
fill_density = 20 | |
nozzle_size = 0.35 | |
print_speed = 30 | |
print_temperature = 210 | |
print_temperature2 = 0 | |
print_temperature3 = 0 | |
print_temperature4 = 0 | |
print_bed_temperature = 50 | |
support = None | |
platform_adhesion = Brim | |
support_dual_extrusion = Both | |
wipe_tower = False | |
wipe_tower_volume = 15 | |
ooze_shield = False | |
filament_diameter = 2.9 | |
filament_diameter2 = 0 | |
filament_diameter3 = 0 | |
filament_diameter4 = 0 | |
filament_flow = 100 | |
retraction_speed = 20.0 | |
retraction_amount = 10 | |
retraction_dual_amount = 16.5 | |
retraction_min_travel = 1.5 | |
retraction_combing = True | |
retraction_minimal_extrusion = 0.02 | |
bottom_thickness = 0.25 | |
object_sink = 0.0 | |
overlap_dual = 0.15 | |
travel_speed = 150 | |
bottom_layer_speed = 20 | |
infill_speed = 0.0 | |
cool_min_layer_time = 5 | |
fan_enabled = True | |
skirt_line_count = 2 | |
skirt_gap = 10.0 | |
skirt_minimal_length = 150.0 | |
fan_full_height = 0.5 | |
fan_speed = 100 | |
fan_speed_max = 100 | |
cool_min_feedrate = 10 | |
cool_head_lift = False | |
solid_top = True | |
solid_bottom = True | |
fill_overlap = 15 | |
support_fill_rate = 15 | |
support_xy_distance = 0.7 | |
support_z_distance = 0.15 | |
spiralize = False | |
brim_line_count = 25 | |
raft_margin = 5 | |
raft_line_spacing = 1.0 | |
raft_base_thickness = 0.3 | |
raft_base_linewidth = 0.7 | |
raft_interface_thickness = 0.2 | |
raft_interface_linewidth = 0.2 | |
fix_horrible_union_all_type_a = False | |
fix_horrible_union_all_type_b = False | |
fix_horrible_use_open_bits = False | |
fix_horrible_extensive_stitching = False | |
plugin_config = (lp1 | |
. | |
object_center_x = -1 | |
object_center_y = -1 | |
[alterations] | |
start.gcode = ;Sliced at: {day} {date} {time} | |
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} | |
;Print time: {print_time} | |
;Filament used: {filament_amount}m {filament_weight}g | |
;Filament cost: {filament_cost} | |
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line | |
;M109 S{print_temperature} ;Uncomment to add your own temperature line | |
G21 ;metric values | |
G90 ;absolute positioning | |
M107 ;start with the fan off | |
G28 X0 Y0 ;Home | |
G92 X-7 Y-6 ;Endstop compensation | |
M117 Printing... | |
end.gcode = ;End GCode | |
M104 S0 ;extruder heater off | |
M140 S0 ;heated bed heater off (if you have it) | |
G91 ;relative positioning | |
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure | |
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more | |
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way | |
M84 ;steppers off | |
G90 ;absolute positioning | |
M117 Ready. | |
start2.gcode = ;Sliced at: {day} {date} {time} | |
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} | |
;Print time: {print_time} | |
;Filament used: {filament_amount}m {filament_weight}g | |
;Filament cost: {filament_cost} | |
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line | |
;M104 S{print_temperature} ;Uncomment to add your own temperature line | |
;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line | |
;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line | |
G21 ;metric values | |
G90 ;absolute positioning | |
M107 ;start with the fan off | |
G28 X0 Y0 ;move X/Y to min endstops | |
G28 Z0 ;move Z to min endstops | |
G1 Z15.0 F{travel_speed} ;move the platform down 15mm | |
T1 ;Switch to the 2nd extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F200 E-{retraction_dual_amount} | |
T0 ;Switch to the first extruder | |
G92 E0 ;zero the extruded length | |
G1 F200 E10 ;extrude 10mm of feed stock | |
G92 E0 ;zero the extruded length again | |
G1 F{travel_speed} | |
;Put printing message on LCD screen | |
M117 Printing... | |
end2.gcode = ;End GCode | |
M104 T0 S0 ;extruder heater off | |
M104 T1 S0 ;extruder heater off | |
M140 S0 ;heated bed heater off (if you have it) | |
G91 ;relative positioning | |
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure | |
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more | |
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way | |
M84 ;steppers off | |
G90 ;absolute positioning | |
support_start.gcode = | |
support_end.gcode = | |
cool_start.gcode = | |
cool_end.gcode = | |
replace.csv = | |
switchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. | |
G92 E0 | |
G1 E-36 F5000 | |
G92 E0 | |
T{extruder} | |
G1 X{new_x} Y{new_y} Z{new_z} F{travel_speed} | |
G1 E36 F5000 | |
G92 E0 | |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment