gistfile1.txt

[    0.000000] Linux version 4.14.101 (openwrt@openwrt-VirtualBox) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r9275-27a30a0)) #0 Mon Feb 25 14:49:16 2019
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] MIPS: machine is RIOT Albatross
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 8051da50, node_mem_map 81007520
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] random: get_random_bytes called from start_kernel+0x8c/0x474 with crng_init=0
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyATH0,115200 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 58212K/65536K available (3790K kernel code, 154K rwdata, 916K rodata, 1212K init, 204K bss, 7324K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] CPU clock: 400.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000013] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.007907] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.092707] pid_max: default: 32768 minimum: 301
[    0.097627] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.103961] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.117277] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.125733] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.131885] pinctrl core: initialized pinctrl subsystem
[    0.138406] NET: Registered protocol family 16
[    0.180148] clocksource: Switched to clocksource MIPS
[    0.185329] NET: Registered protocol family 2
[    0.189486] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.195268] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.201602] TCP: Hash tables configured (established 1024 bind 1024)
[    0.208126] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.213809] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.220392] NET: Registered protocol family 1
[    0.224368] PCI: CLS 0 bytes, default 32
[    0.229260] Crashlog allocated RAM at address 0x3f00000
[    0.235066] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.247754] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.252204] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.275313] io scheduler noop registered
[    0.277785] io scheduler deadline registered (default)
[    0.283422] ar7200-usb-phy usb-phy: phy reset is missing
[    0.288820] pinctrl-single 18040028.pinmux: 64 pins at pa b8040028 size 8
[    0.295580] pinctrl-single 18040030.pinmux-extended: 32 pins at pa b8040030 size 4
[    0.303140] pinctrl-single 180600ac.pinmux_mdio: 32 pins at pa b80600ac size 4
[    0.311342] gpio-export gpio-export: 6 gpio(s) exported
[    0.316247] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.322706] 18020000.uart: ttyATH0 at MMIO 0x18020000 (irq = 8, base_baud = 1562500) is a AR933X UART
[    0.331203] console [ttyATH0] enabled
[    0.337975] bootconsole [early0] disabled
[    0.364958] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.368275] 4 fixed-partitions partitions found on MTD device spi0.0
[    0.374587] Creating 4 MTD partitions on "spi0.0":
[    0.379341] 0x000000000000-0x000000040000 : "u-boot"
[    0.385551] 0x000000040000-0x000000050000 : "u-boot-env"
[    0.390748] 0x000000050000-0x000000ff0000 : "firmware"
[    0.418131] 2 uimage-fw partitions found on MTD device firmware
[    0.422652] 0x000000050000-0x0000001e0000 : "kernel"
[    0.428631] 0x0000001e0000-0x000000ff0000 : "rootfs"
[    0.433625] mtd: device 4 (rootfs) set to be root filesystem
[    0.438173] 1 squashfs-split partitions found on MTD device rootfs
[    0.444397] 0x000000570000-0x000000ff0000 : "rootfs_data"
[    0.450933] 0x000000ff0000-0x000001000000 : "ART"
[    0.457023] libphy: Fixed MDIO Bus: probed
[    0.800627] libphy: ag71xx_mdio: probed
[    1.090224] mdio-bus.0:1f: Found an AR7240/AR9330 built-in switch
[    1.095127] libphy: ar7240sw_mdio: probed
[    1.481828] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:1f:04 [uid=004dd041, driver=Generic PHY]
[    1.490870] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    1.832167] ag71xx 1a000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[    1.840713] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    1.848595] NET: Registered protocol family 10
[    1.858150] Segment Routing with IPv6
[    1.860590] NET: Registered protocol family 17
[    1.864866] 8021q: 802.1Q VLAN Support v1.8
[    1.879331] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.895419] Freeing unused kernel memory: 1212K
[    1.898485] This architecture does not have kernel memory protection.
[    2.540163] random: fast init done
[    2.748607] init: Console is alive
[    4.130683] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.339959] usbcore: registered new interface driver usbfs
[    4.344216] usbcore: registered new interface driver hub
[    4.349436] usbcore: registered new device driver usb
[    4.365034] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.375509] chipidea-usb2 1b000000.usb: 1b000000.usb supply vbus not found, using dummy regulator
[    4.386078] ci_hdrc ci_hdrc.0: EHCI Host Controller
[    4.389568] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
[    4.420167] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[    4.425338] hub 1-0:1.0: USB hub found
[    4.428427] hub 1-0:1.0: 1 port detected
[    4.435515] ehci-platform: EHCI generic platform driver
[    4.441166] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.450516] init: - preinit -
[    5.274153] usb 1-1: new full-speed USB device number 2 using ci_hdrc
[    5.611157] random: procd: uninitialized urandom read (4 bytes read)
[    5.791616] random: jshn: uninitialized urandom read (4 bytes read)
[    6.020383] random: jshn: uninitialized urandom read (4 bytes read)
[    6.448824] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    8.572368] eth0: link up (100Mbps/Full duplex)
[    8.575490] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    9.805393] jffs2: notice: (462) jffs2_build_xattr_subsystem: complete building xattr subsystem, 4 of xdatum (2 unchecked, 2 orphan) and 15 of xref (2 dead, 0 orphan) found.
[    9.821375] mount_root: switching to jffs2 overlay
[    9.865534] overlayfs: upper fs does not support tmpfile.
[    9.877546] urandom-seed: Seeding with /etc/urandom.seed
[   10.161192] eth0: link down
[   10.179770] procd: - early -
[   10.860389] procd: - ubus -
[   10.982367] urandom_read: 5 callbacks suppressed
[   10.982380] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.994944] random: ubusd: uninitialized urandom read (4 bytes read)
[   11.001913] procd: - init -
[   16.695511] kmodloader: loading kernel modules from /etc/modules.d/*
[   16.713451] loop: module loaded
[   16.728056] tun: Universal TUN/TAP device driver, 1.6
[   16.739257] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   16.768803] i2c /dev entries driver
[   16.783902] cdc_acm 1-1:1.0: ttyACM0: USB ACM device
[   16.789501] usbcore: registered new interface driver cdc_acm
[   16.793792] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   16.805755] Loading modules backported from Linux version v4.19.23-0-g67d52fae61c1
[   16.811968] Backport generated by backports.git v4.19.23-1-0-g480a925a
[   16.823108] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.843121] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[   16.949332] xt_time: kernel timezone is -0000
[   17.045051] PPP generic driver version 2.4.2
[   17.056723] NET: Registered protocol family 24
[   17.141736] ath: EEPROM regdomain: 0x0
[   17.141751] ath: EEPROM indicates default country code should be used
[   17.141756] ath: doing EEPROM country->regdmn map search
[   17.141777] ath: country maps to regdmn code: 0x3a
[   17.141785] ath: Country alpha2 being used: US
[   17.141790] ath: Regpair used: 0x3a
[   17.157093] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   17.159900] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[   17.289801] kmodloader: done loading kernel modules from /etc/modules.d/*
[   28.269453] Custom GPIO-based I2C driver version 0.1.1
[   28.273844] i2c-gpio i2c-gpio.0: using pins 23 (SDA) and 22 (SCL)
[   32.601125] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   34.732048] eth0: link up (100Mbps/Full duplex)
[   34.735176] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   37.016623] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   37.044907] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   83.647777] random: crng init done