Created
February 5, 2021 00:45
-
-
Save DavideFioravanti/da60059266d7a6541b5f3f5647a5104e to your computer and use it in GitHub Desktop.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| F0: 102B 0000 | |
| F6: 0000 0000 | |
| V0: 0000 0000 [0001] | |
| 00: 0000 0000 | |
| BP: 0000 0041 [0000] | |
| G0: 0190 0000 | |
| T0: 0000 036D [000F] | |
| Jump to BL | |
| UNIVPLL_CON0 = 0xFE000000!!! | |
| mt_pll_init: Set pll frequency for 25M crystal | |
| RAM_CONSOLE preloader last status: 0x0 0x0 0x0 0x0 0x0 0x0 | |
| [PMIC_WRAP]wrap_init pass,the return value=0. | |
| [pmic_init] Preloader Start.................. | |
| [pmic_init] MT6380 CHIP Code, reg_val = 0, 1:E2 0:E3 | |
| [pmic_init] Done................... | |
| Chip part number:7622B | |
| MT7622 Version: 1.2.8, (iPA) | |
| SSC OFF | |
| mt_pll_post_init: mt_get_cpu_freq = 1350000Khz | |
| mt_pll_post_init: mt_get_mem_freq = 1600000Khz | |
| mt_pll_post_init: mt_get_bus_freq = 1119920Khz | |
| [PLFM] Init I2C: OK(0) | |
| [BLDR] Build Time: 20200522-165358 | |
| ==== Dump RGU Reg ======== | |
| RGU MODE: 14 | |
| RGU LENGTH: FFE0 | |
| RGU STA: 40000000 | |
| RGU INTERVAL: FFF | |
| RGU SWSYSRST: 8000 | |
| ==== Dump RGU Reg End ==== | |
| RGU: g_rgu_satus:2 | |
| mtk_wdt_mode_config mode value=10, tmp:22000010 | |
| PL RGU RST: ?? | |
| SW reset with bypass power key flag | |
| Find bypass powerkey flag | |
| WDT NONRST=0x20000000 | |
| WDT IRQ_EN=0x340003 | |
| RGU mtk_wdt_init:MTK_WDT_DEBUG_CTL(590200F3) | |
| [EMI] MDL number = 2 | |
| [EMI] DRAMC calibration start | |
| [EMI] DRAMC calibration end | |
| [EMI]rank size auto detect | |
| [EMI]start_addr[0x40000000]=0x12345678, test_addr[0x48000000]= 0xEDCBA987 | |
| [EMI]start_addr[0x40000000]=0x12345678, test_addr[0x50000000]= 0xEDCBA987 | |
| [EMI]start_addr[0x40000000]=0xEDCBA987, test_addr[0x60000000]= 0xEDCBA987 | |
| [EMI]rank0 size: 0x20000000 | |
| [MEM] complex R/W mem test pass | |
| RAM_CONSOLE wdt status (0x2)=0x2 | |
| [BBT] BMT.v2 is found at 0x3FF | |
| [PLFM] Init Boot Device: OK(0) | |
| [PART] blksz: 2048B | |
| [PART] [0x0000000000000000-0x000000000007FFFF] "PRELOADER" (256 blocks) | |
| [PART] [0x0000000000080000-0x00000000000BFFFF] "tee1" (128 blocks) | |
| [PART] [0x00000000000C0000-0x000000000013FFFF] "lk" (256 blocks) | |
| Device APC domain init setup: | |
| Domain Setup (0x0) | |
| Domain Setup (0x0) | |
| Device APC domain after setup: | |
| Domain Setup (0x0) | |
| Domain Setup (0x0) | |
| [PART] Image with part header | |
| [PART] name : U-Boot | |
| [PART] addr : 41E00000h mode : -1 | |
| [PART] size : 342676 | |
| [PART] magic: 58881688h | |
| [PART] load "lk" from 0x00000000000C0200 (dev) to 0x41E00000 (mem) [SUCCESS] | |
| [PART] load speed: 16731KB/s, 342676 bytes, 20ms | |
| load lk (ret=0) | |
| [PART] Image with part header | |
| [PART] name : atf | |
| [PART] addr : FFFFFFFFh mode : -1 | |
| [PART] size : 57936 | |
| [PART] magic: 58881688h | |
| [PART] load "tee1" from 0x0000000000080200 (dev) to 0x43000DC0 (mem) [SUCCESS] | |
| [PART] load speed: 18859KB/s, 57936 bytes, 3ms | |
| load tee1 (ret=0) | |
| [BLDR] bldr load tee part ret=0x0, addr=0x43001000 | |
| [BLDR] boot part. not found | |
| [BLDR] part_load_images ret=0x0 | |
| [BLDR] Others, jump to ATF | |
| [BLDR] jump to 0x41E00000 | |
| [BLDR] <0x41E00000>=0xEA00000F | |
| [BLDR] <0x41E00004>=0xE59FF014 | |
| U-Boot 2014.04-rc1 Version: 1.0.0.1 (Jul 21 2020 - 12:07:36) | |
| static declaration g_total_rank_size = 0x1F000000 | |
| DRAM: 496 MiB | |
| NAND: Recognize SNAND: ID [e5 71 ], Device Name [FM35X1GA], Page Size [2048]B Spare Size [64]B Total Size [128]MB | |
| [mtk_snand] probe successfully! | |
| [BBT] BMT.v2 is found at 0x3ff | |
| 128 MiB | |
| First booting, write default data (s_env) to flash... | |
| [mtk_nand_erase_hw] mtk_nand_erase_hw @4249, ret:0x40. page:0x680 | |
| [mtk_nand_erase_hw] mtk_nand_erase_hw @4249, ret:0x40. page:0x700 | |
| In: serial | |
| Out: serial | |
| Err: serial | |
| Net: mtk_eth | |
| Uip activated | |
| [?25l[2J[1;1H[1;1H[2K[2;1H *** U-Boot SPI NAND ***[0K[3;1H[2K[14;1H[2K[15;1H Press UP/DOWN to move or Press 1~8 to choose, ENTER to select[0K[16;1H[2K[4;1H 1. System Load Linux to SDRAM via TFTP.[5;1H 2. System Load Linux Kernel then write to Flash via TFTP.[6;1H [7m3. Boot master system code via Flash.[0m[7;1H 4. Boot slave system code via Flash.[8;1H 5. System Load U-Boot then write to Flash via TFTP.[9;1H 6. System Load U-Boot then write to Flash via Serial.[10;1H 7. System Load ATF then write to Flash via TFTP.[11;1H 8. System Load Preloader then write to Flash via TFTP.[12;1H U-Boot console[14;1H Hit any key to stop autoboot: 3 2 1 0 [14;1H[2K[?25h[2J[1;1H | |
| NAND read: device 0 offset 0x500000, size 0x2000 | |
| 8192 bytes read: OK | |
| [do_read_image_blks] This is a FIT image,img_size = 0x32b5b0 | |
| [do_read_image_blks] img_blks = 0x657 | |
| [do_read_image_blks] img_align_size = 0x32b800 | |
| NAND read: device 0 offset 0x500000, size 0x32b800 | |
| 3323904 bytes read: OK | |
| bootm flag=0, states=70f | |
| ## Loading kernel from FIT Image at 4007ff28 ... | |
| Using 'config@1' configuration | |
| Trying 'kernel@1' kernel subimage | |
| Description: ARM64 OpenWrt Linux-5.10.10 | |
| Type: Kernel Image | |
| Compression: lzma compressed | |
| Data Start: 0x40080010 | |
| Data Size: 3297480 Bytes = 3.1 MiB | |
| Architecture: AArch64 | |
| OS: Linux | |
| Load Address: 0x44000000 | |
| Entry Point: 0x44000000 | |
| Hash algo: crc32 | |
| Hash value: 0ea838a0 | |
| Hash algo: sha1 | |
| Hash value: 3d8ff929f59ace0ac54c134c7c8f9519d2325287 | |
| Verifying Hash Integrity ... crc32+ sha1+ OK | |
| ## Loading fdt from FIT Image at 4007ff28 ... | |
| Using 'config@1' configuration | |
| Trying 'fdt@1' fdt subimage | |
| Description: ARM64 OpenWrt linksys_e8450 device tree blob | |
| Type: Flat Device Tree | |
| Compression: uncompressed | |
| Data Start: 0x403a5218 | |
| Data Size: 23948 Bytes = 23.4 KiB | |
| Architecture: AArch64 | |
| Hash algo: crc32 | |
| Hash value: ae8c250d | |
| Hash algo: sha1 | |
| Hash value: 87f597bb6915a4c1d40a521a542f545f1b5291b4 | |
| Verifying Hash Integrity ... crc32+ sha1+ OK | |
| Booting using the fdt blob at 0x403a5218 | |
| Uncompressing Kernel Image ... OK | |
| Loading Device Tree to 5cf09000, end 5cf11d8b ... OK | |
| Starting kernel ... | |
| [ATF][ 5.256201]save kernel info | |
| [ATF][ 5.259137]Kernel_EL2 | |
| [ATF][ 5.261808]Kernel is 64Bit | |
| [ATF][ 5.264896]pc=0x44000000, r0=0x5cf09000, r1=0x0 | |
| INFO: BL3-1: Preparing for EL3 exit to normal world, Kernel | |
| INFO: BL3-1: Next image address = 0x44000000 | |
| INFO: BL3-1: Next image spsr = 0x3c9 | |
| [ATF][ 5.282594]el3_exit | |
| [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] | |
| [ 0.000000] Linux version 5.10.10 (fiore@fiore-FISSO-UBUNTU20) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 8.4.0 r15688-374f24fef4) 8.4.0, GNU ld (GNU Binutils) 2.34) #0 SMP Thu Feb 4 12:16:06 2021 | |
| [ 0.000000] Machine model: Linksys E8450 | |
| [ 0.000000] Zone ranges: | |
| [ 0.000000] DMA [mem 0x0000000040000000-0x000000005fffffff] | |
| [ 0.000000] DMA32 empty | |
| [ 0.000000] Normal empty | |
| [ 0.000000] Movable zone start for each node | |
| [ 0.000000] Early memory node ranges | |
| [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff] | |
| [ 0.000000] node 0: [mem 0x0000000043030000-0x000000005fffffff] | |
| [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff] | |
| [ 0.000000] On node 0 totalpages: 131024 | |
| [ 0.000000] DMA zone: 2048 pages used for memmap | |
| [ 0.000000] DMA zone: 0 pages reserved | |
| [ 0.000000] DMA zone: 131024 pages, LIFO batch:31 | |
| [ 0.000000] psci: probing for conduit method from DT. | |
| [ 0.000000] psci: PSCIv0.2 detected in firmware. | |
| [ 0.000000] psci: Using standard PSCI v0.2 function IDs | |
| [ 0.000000] psci: Trusted OS migration not required | |
| [ 0.000000] percpu: Embedded 20 pages/cpu s44568 r8192 d29160 u81920 | |
| [ 0.000000] pcpu-alloc: s44568 r8192 d29160 u81920 alloc=20*4096 | |
| [ 0.000000] pcpu-alloc: [0] 0 [0] 1 | |
| [ 0.000000] Detected VIPT I-cache on CPU0 | |
| [ 0.000000] CPU features: detected: ARM erratum 845719 | |
| [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration | |
| [ 0.000000] CPU features: detected: ARM erratum 843419 | |
| [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 128976 | |
| [ 0.000000] Kernel command line: console=ttyS0,115200 rootdelay=1 rootfstype=squashfs earlyprintk mtdparts=master | |
| [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) | |
| [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) | |
| [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off | |
| [ 0.000000] Memory: 495172K/524096K available (6782K kernel code, 832K rwdata, 1996K rodata, 448K init, 290K bss, 28924K reserved, 0K cma-reserved) | |
| [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 | |
| [ 0.000000] rcu: Hierarchical RCU implementation. | |
| [ 0.000000] rcu: CONFIG_RCU_FANOUT set to non-default value of 32. | |
| [ 0.000000] Tracing variant of Tasks RCU enabled. | |
| [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. | |
| [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 | |
| [ 0.000000] GIC: GICv2 detected, but range too small and irqchip.gicv2_force_probe not set | |
| [ 0.000000] random: get_random_bytes called from start_kernel+0x340/0x48c with crng_init=0 | |
| [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys). | |
| [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns | |
| [ 0.000003] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns | |
| [ 0.000163] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=50000) | |
| [ 0.000173] pid_max: default: 32768 minimum: 301 | |
| [ 0.000253] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) | |
| [ 0.000262] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) | |
| [ 0.001234] rcu: Hierarchical SRCU implementation. | |
| [ 0.001325] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build | |
| [ 0.001509] smp: Bringing up secondary CPUs ... | |
| [ 0.001817] Detected VIPT I-cache on CPU1 | |
| [ 0.001862] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] | |
| [ 0.001925] smp: Brought up 1 node, 2 CPUs | |
| [ 0.001933] SMP: Total of 2 processors activated. | |
| [ 0.001938] CPU features: detected: 32-bit EL0 Support | |
| [ 0.001942] CPU features: detected: CRC32 instructions | |
| [ 0.002061] CPU: All CPU(s) started at EL2 | |
| [ 0.002073] alternatives: patching kernel code | |
| [ 0.005151] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns | |
| [ 0.005167] futex hash table entries: 512 (order: 3, 32768 bytes, linear) | |
| [ 0.005250] pinctrl core: initialized pinctrl subsystem | |
| [ 0.005683] NET: Registered protocol family 16 | |
| [ 0.006285] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations | |
| [ 0.006312] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations | |
| [ 0.006335] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations | |
| [ 0.006614] thermal_sys: Registered thermal governor 'fair_share' | |
| [ 0.006618] thermal_sys: Registered thermal governor 'bang_bang' | |
| [ 0.006623] thermal_sys: Registered thermal governor 'step_wise' | |
| [ 0.006627] thermal_sys: Registered thermal governor 'user_space' | |
| [ 0.006869] ASID allocator initialised with 65536 entries | |
| [ 0.035906] SCSI subsystem initialized | |
| [ 0.036097] libata version 3.00 loaded. | |
| [ 0.036312] usbcore: registered new interface driver usbfs | |
| [ 0.036346] usbcore: registered new interface driver hub | |
| [ 0.036379] usbcore: registered new device driver usb | |
| [ 0.036903] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 | |
| [ 0.039146] clocksource: Switched to clocksource arch_sys_counter | |
| [ 0.039734] NET: Registered protocol family 2 | |
| [ 0.040056] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) | |
| [ 0.040070] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) | |
| [ 0.040103] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) | |
| [ 0.040163] TCP: Hash tables configured (established 4096 bind 4096) | |
| [ 0.040316] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) | |
| [ 0.040334] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) | |
| [ 0.040444] NET: Registered protocol family 1 | |
| [ 0.040466] PCI: CLS 0 bytes, default 64 | |
| [ 0.041995] workingset: timestamp_bits=46 max_order=17 bucket_order=0 | |
| [ 0.044165] squashfs: version 4.0 (2009/01/31) Phillip Lougher | |
| [ 0.044176] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. | |
| [ 0.075939] mtk-tphy 1a0c4000.usb-phy: failed to get ref_clk(id-1) | |
| [ 0.079888] mt-pmic-pwrap 10001000.pwrap: unexpected interrupt int=0x1 | |
| [ 0.094163] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled | |
| [ 0.094865] printk: console [ttyS0] disabled | |
| [ 0.094931] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 23, base_baud = 1562500) is a 16550A | |
| [ 0.680718] printk: console [ttyS0] enabled | |
| [ 0.685459] 11004000.serial: ttyS1 at MMIO 0x11004000 (irq = 24, base_baud = 1562500) is a 16550A | |
| [ 0.694986] 1100c000.serial: ttyS2 at MMIO 0x1100c000 (irq = 28, base_baud = 17499995) is a MediaTek BTIF | |
| [ 0.704648] serial serial0: tty port ttyS2 registered | |
| [ 0.710004] cacheinfo: Unable to detect cache hierarchy for CPU 0 | |
| [ 0.716582] mtk-ecc 1100e000.ecc: probed | |
| [ 0.722285] spi-nand spi2.0: Fidelix SPI NAND was found. | |
| [ 0.727634] spi-nand spi2.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 | |
| [ 0.737217] [BBT] BMT.v2 is found at 0x3ff | |
| [ 0.741504] 12 fixed-partitions partitions found on MTD device spi2.0 | |
| [ 0.747949] Creating 12 MTD partitions on "spi2.0": | |
| [ 0.752826] 0x000000000000-0x000000080000 : "Preloader" | |
| [ 0.759175] 0x000000080000-0x0000000c0000 : "ATF" | |
| [ 0.764595] 0x0000000c0000-0x000000140000 : "u-boot" | |
| [ 0.770584] 0x000000140000-0x0000001c0000 : "u-boot-env" | |
| [ 0.776900] 0x0000001c0000-0x0000002c0000 : "factory" | |
| [ 0.783543] 0x000000300000-0x000000320000 : "devinfo" | |
| [ 0.789151] 0x000000320000-0x000000340000 : "senv" | |
| [ 0.794533] 0x000000360000-0x000000380000 : "bootseq" | |
| [ 0.800159] 0x000000500000-0x000002300000 : "firmware1" | |
| [ 0.832019] random: fast init done | |
| [ 0.844254] 2 fit-fw partitions found on MTD device firmware1 | |
| [ 0.850011] Creating 2 MTD partitions on "firmware1": | |
| [ 0.855063] 0x000000000000-0x000000340000 : "kernel" | |
| [ 0.860466] 0x000000340000-0x000001e00000 : "rootfs" | |
| [ 0.865879] mtd: device 10 (rootfs) set to be root filesystem | |
| [ 0.871797] 1 squashfs-split partitions found on MTD device rootfs | |
| [ 0.877980] 0x000000880000-0x000001e00000 : "rootfs_data" | |
| [ 0.883843] 0x000002300000-0x000004100000 : "firmware2" | |
| [ 0.924072] 0x000004100000-0x000005a00000 : "data" | |
| [ 0.958080] 0x000005a00000-0x000006e00000 : "mfg" | |
| [ 0.986812] libphy: Fixed MDIO Bus: probed | |
| [ 1.014555] libphy: mdio: probed | |
| [ 1.018366] mtk_soc_eth 1b100000.ethernet: generated random MAC address 72:ab:e5:58:90:5a | |
| [ 1.026813] mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xffffffc011680000, irq 37 | |
| [ 1.037170] rtc_mt7622 10212800.rtc: registered as rtc0 | |
| [ 1.042435] rtc_mt7622 10212800.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) | |
| [ 1.052206] mtk-wdt 10212000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0) | |
| [ 1.062948] NET: Registered protocol family 10 | |
| [ 1.067975] Segment Routing with IPv6 | |
| [ 1.071694] NET: Registered protocol family 17 | |
| [ 1.076265] 8021q: 802.1Q VLAN Support v1.8 | |
| [ 1.090387] mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges: | |
| [ 1.096944] mtk-pcie 1a143000.pcie: Parsing ranges property... | |
| [ 1.102779] mtk-pcie 1a143000.pcie: MEM 0x0020000000..0x0027ffffff -> 0x0020000000 | |
| [ 1.127304] mtk-pcie 1a143000.pcie: PCI host bridge to bus 0000:00 | |
| [ 1.133493] pci_bus 0000:00: root bus resource [bus 00-ff] | |
| [ 1.138976] pci_bus 0000:00: root bus resource [mem 0x20000000-0x27ffffff] | |
| [ 1.145845] pci_bus 0000:00: scanning bus | |
| [ 1.149892] pci 0000:00:00.0: [14c3:3258] type 01 class 0x060400 | |
| [ 1.155924] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x1ffffffff 64bit pref] | |
| [ 1.164585] pci_bus 0000:00: fixups for bus | |
| [ 1.168770] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0 | |
| [ 1.175468] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring | |
| [ 1.183480] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1 | |
| [ 1.190269] pci_bus 0000:01: scanning bus | |
| [ 1.194484] pci 0000:01:00.0: [14c3:7915] type 00 class 0x000280 | |
| [ 1.200664] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref] | |
| [ 1.207989] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref] | |
| [ 1.215313] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref] | |
| [ 1.223271] pci 0000:01:00.0: supports D1 D2 | |
| [ 1.227537] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold | |
| [ 1.234169] pci 0000:01:00.0: PME# disabled | |
| [ 1.238652] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) | |
| [ 1.264307] pci_bus 0000:01: fixups for bus | |
| [ 1.268496] pci_bus 0000:01: bus scan returning with max=01 | |
| [ 1.274069] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 | |
| [ 1.280682] pci_bus 0000:00: bus scan returning with max=01 | |
| [ 1.286265] pci 0000:00:00.0: BAR 0: no space for [mem size 0x200000000 64bit pref] | |
| [ 1.293918] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x200000000 64bit pref] | |
| [ 1.301917] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff] | |
| [ 1.308704] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit pref] | |
| [ 1.316527] pci 0000:01:00.0: BAR 2: assigned [mem 0x20100000-0x20103fff 64bit pref] | |
| [ 1.324353] pci 0000:01:00.0: BAR 4: assigned [mem 0x20104000-0x20104fff 64bit pref] | |
| [ 1.332174] pci 0000:00:00.0: PCI bridge to [bus 01] | |
| [ 1.337141] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff] | |
| [ 1.343952] pci 0000:00:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256 | |
| [ 1.352505] pci 0000:01:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 128 | |
| [ 1.361000] pcieport 0000:00:00.0: of_irq_parse_pci: failed with rc=-22 | |
| [ 1.367610] pcieport 0000:00:00.0: assign IRQ: got 0 | |
| [ 1.372578] pcieport 0000:00:00.0: enabling device (0000 -> 0002) | |
| [ 1.378684] pcieport 0000:00:00.0: enabling bus mastering | |
| [ 1.384550] mtk-pcie 1a145000.pcie: host bridge /pcie@1a145000 ranges: | |
| [ 1.391085] mtk-pcie 1a145000.pcie: Parsing ranges property... | |
| [ 1.396923] mtk-pcie 1a145000.pcie: MEM 0x0028000000..0x002fffffff -> 0x0028000000 | |
| [ 1.505090] mtk-pcie 1a145000.pcie: Port1 link down | |
| [ 1.510063] mtk-pcie 1a145000.pcie: PCI host bridge to bus 0001:00 | |
| [ 1.516247] pci_bus 0001:00: root bus resource [bus 00-ff] | |
| [ 1.521730] pci_bus 0001:00: root bus resource [mem 0x28000000-0x2fffffff] | |
| [ 1.528600] pci_bus 0001:00: scanning bus | |
| [ 1.533664] pci_bus 0001:00: fixups for bus | |
| [ 1.537845] pci_bus 0001:00: bus scan returning with max=00 | |
| [ 1.543677] mtk_hsdma 1b007000.dma-controller: Using 3 as missing dma-requests property | |
| [ 1.551893] mtk_hsdma 1b007000.dma-controller: MediaTek HSDMA driver registered | |
| [ 1.596332] libphy: dsa slave smi: probed | |
| [ 1.601232] mt7530 mdio-bus:00 lan1 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] (irq=POLL) | |
| [ 1.611745] mt7530 mdio-bus:00 lan2 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] (irq=POLL) | |
| [ 1.622153] mt7530 mdio-bus:00 lan3 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] (irq=POLL) | |
| [ 1.632561] mt7530 mdio-bus:00 lan4 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] (irq=POLL) | |
| [ 1.642958] mt7530 mdio-bus:00 wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY] (irq=POLL) | |
| [ 1.652998] mt7530 mdio-bus:00: configuring for fixed/2500base-x link mode | |
| [ 1.660569] mt7530 mdio-bus:00: Link is Up - 2.5Gbps/Full - flow control rx/tx | |
| [ 1.661176] DSA: tree 0 setup | |
| [ 1.671524] xhci-mtk 1a0c0000.usb: xHCI Host Controller | |
| [ 1.676793] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 1 | |
| [ 1.685846] xhci-mtk 1a0c0000.usb: hcc params 0x01403198 hci version 0x96 quirks 0x0000000000210010 | |
| [ 1.694931] xhci-mtk 1a0c0000.usb: irq 33, io mem 0x1a0c0000 | |
| [ 1.701012] hub 1-0:1.0: USB hub found | |
| [ 1.704782] hub 1-0:1.0: 2 ports detected | |
| [ 1.709003] xhci-mtk 1a0c0000.usb: xHCI Host Controller | |
| [ 1.714233] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 2 | |
| [ 1.721631] xhci-mtk 1a0c0000.usb: Host supports USB 3.0 SuperSpeed | |
| [ 1.727926] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. | |
| [ 1.736249] hub 2-0:1.0: USB hub found | |
| [ 1.740011] hub 2-0:1.0: 1 port detected | |
| [ 1.744737] UBI error: no valid UBI magic found inside mtd13 | |
| [ 1.751028] Waiting 1 sec before mounting root device... | |
| [ 2.791130] VFS: Mounted root (squashfs filesystem) readonly on device 31:10. | |
| [ 2.798463] Freeing unused kernel memory: 448K | |
| [ 2.807189] Run /sbin/init as init process | |
| [ 2.811282] with arguments: | |
| [ 2.814239] /sbin/init | |
| [ 2.816940] earlyprintk | |
| [ 2.819728] with environment: | |
| [ 2.822859] HOME=/ | |
| [ 2.825214] TERM=linux | |
| [ 2.827915] mtdparts=master | |
| [ 3.131210] init: Console is alive | |
| [ 3.134694] init: - watchdog - | |
| [ 3.520503] random: crng init done | |
| [ 3.580783] kmodloader: loading kernel modules from /etc/modules-boot.d/* | |
| [ 3.659804] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver | |
| [ 3.666984] ehci-fsl: Freescale EHCI Host controller driver | |
| [ 3.673176] ehci-platform: EHCI generic platform driver | |
| [ 3.679964] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver | |
| [ 3.686650] ohci-platform: OHCI generic platform driver | |
| [ 3.693956] kmodloader: done loading kernel modules from /etc/modules-boot.d/* | |
| [ 3.701767] init: - preinit - | |
| [ 4.167586] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode | |
| [ 4.176115] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx | |
| [ 4.184895] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready | |
| [ 4.191815] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode | |
| [ 4.198906] 8021q: adding VLAN 0 to HW filter on device lan1 | |
| Press the [f] key and hit [enter] to enter failsafe mode | |
| Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level | |
| [ 8.287172] mount_root: jffs2 not ready yet, using temporary tmpfs overlay | |
| [ 8.295561] overlayfs: "xino" feature enabled using 2 upper inode bits. | |
| [ 8.303421] urandom-seed: Seed file not found (/etc/urandom.seed) | |
| [ 8.422786] procd: - early - | |
| [ 8.425719] procd: - watchdog - | |
| Failed to connect to ubus | |
| [ 8.984568] procd: - watchdog - | |
| [ 9.057288] procd: - ubus - | |
| [ 9.143056] procd: - init - | |
| Please press Enter to activate this console. | |
| [ 9.376812] urngd: v1.0.2 started. | |
| [ 9.428981] kmodloader: loading kernel modules from /etc/modules.d/* | |
| [ 9.545075] Loading modules backported from Linux version v5.10-rc6-0-gb65054597872 | |
| [ 9.552765] Backport generated by backports.git v5.10-rc6-1-0-g3a9d70a3 | |
| [ 9.599255] xt_time: kernel timezone is -0000 | |
| [ 9.642438] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' | |
| [ 9.652984] mt7915e 0000:01:00.0: assign IRQ: got 145 | |
| [ 9.658152] pci 0000:00:00.0: enabling bus mastering | |
| [ 9.663141] mt7915e 0000:01:00.0: enabling device (0000 -> 0002) | |
| [ 9.669246] mt7915e 0000:01:00.0: enabling bus mastering | |
| [ 9.781614] mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a | |
| [ 9.781614] | |
| [ 9.781795] mt7915e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20200819112315a | |
| [ 9.781795] | |
| [ 10.015446] mt7622-wmac 18000000.wmac: N9 Firmware Version: 2.0, Build Time: 20200131180931 | |
| [ 10.133460] mt7915e 0000:01:00.0: WM Firmware Version: ____000000, Build Time: 20200819112349 | |
| [ 10.211902] mt7915e 0000:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20200819112407 | |
| [ 10.337733] PPP generic driver version 2.4.2 | |
| [ 10.344250] NET: Registered protocol family 24 | |
| [ 10.360725] kmodloader: done loading kernel modules from /etc/modules.d/* | |
| [ 14.832347] mtk_soc_eth 1b100000.ethernet eth0: Link is Down | |
| [ 14.838840] mtk_soc_eth 1b100000.ethernet: PPE table busy | |
| [ 14.846661] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode | |
| [ 14.855379] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx | |
| [ 14.864063] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready | |
| [ 14.871810] device eth0 entered promiscuous mode | |
| [ 14.877538] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode | |
| [ 14.885040] 8021q: adding VLAN 0 to HW filter on device lan1 | |
| [ 14.893088] br-lan: port 1(lan1) entered blocking state | |
| [ 14.898375] br-lan: port 1(lan1) entered disabled state | |
| [ 14.904029] device lan1 entered promiscuous mode | |
| [ 14.915176] mt7530 mdio-bus:00 lan2: configuring for phy/gmii link mode | |
| [ 14.922572] 8021q: adding VLAN 0 to HW filter on device lan2 | |
| [ 14.933058] br-lan: port 2(lan2) entered blocking state | |
| [ 14.938337] br-lan: port 2(lan2) entered disabled state | |
| [ 14.944163] device lan2 entered promiscuous mode | |
| [ 14.953270] mt7530 mdio-bus:00 lan3: configuring for phy/gmii link mode | |
| [ 14.960466] 8021q: adding VLAN 0 to HW filter on device lan3 | |
| [ 14.968636] br-lan: port 3(lan3) entered blocking state | |
| [ 14.973866] br-lan: port 3(lan3) entered disabled state | |
| [ 14.980232] device lan3 entered promiscuous mode | |
| [ 14.989822] mt7530 mdio-bus:00 lan4: configuring for phy/gmii link mode | |
| [ 14.997091] 8021q: adding VLAN 0 to HW filter on device lan4 | |
| [ 15.007801] mt7530 mdio-bus:00 lan4: Link is Up - 1Gbps/Full - flow control rx/tx | |
| [ 15.017631] br-lan: port 4(lan4) entered blocking state | |
| [ 15.022924] br-lan: port 4(lan4) entered disabled state | |
| [ 15.029407] device lan4 entered promiscuous mode | |
| [ 15.036552] br-lan: port 4(lan4) entered blocking state | |
| [ 15.041809] br-lan: port 4(lan4) entered forwarding state | |
| [ 15.047345] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready | |
| [ 15.057770] mt7530 mdio-bus:00 wan: configuring for phy/gmii link mode | |
| [ 15.064916] 8021q: adding VLAN 0 to HW filter on device wan | |
| [ 15.287508] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 | |
| [ 15.296059] jffs2_build_filesystem(): unlocking the mtd device... | |
| [ 15.296066] done. | |
| [ 15.304261] jffs2_build_filesystem(): erasing all blocks after the end marker... | |
| [ 17.279424] done. | |
| [ 17.288844] jffs2: notice: (2415) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. | |
| [ 17.339095] overlayfs: upper fs does not support tmpfile. | |
| [ 17.344759] overlayfs: "xino" feature enabled using 32 upper inode bits. | |
| BusyBox v1.31.1 () built-in shell (ash) | |
| _______ ________ __ | |
| | |.-----.-----.-----.| | | |.----.| |_ | |
| | - || _ | -__| || | | || _|| _| | |
| |_______|| __|_____|__|__||________||__| |____| | |
| |__| W I R E L E S S F R E E D O M | |
| ----------------------------------------------------- | |
| OpenWrt SNAPSHOT, r15688-374f24fef4 | |
| ----------------------------------------------------- | |
| === WARNING! ===================================== | |
| There is no root password defined on this device! | |
| Use the "passwd" command to set up a new password | |
| in order to prevent unauthorized SSH logins. | |
| -------------------------------------------------- | |
| root@OpenWrt:/# dd if=/dev/urandom of=/root/random.file bs=1M count=10; | |
| 10+0 records in | |
| 10+0 records out | |
| root@OpenWrt:/# sync; | |
| root@OpenWrt:/# md5sum /root/random.file > /root/random.file.md5; | |
| root@OpenWrt:/# cat /root/random.file.md5; | |
| 8506b23e9ea97fb6bb325f74c324bf8a /root/random.file | |
| root@OpenWrt:/# sync; | |
| root@OpenWrt:/# reboot | |
| root@OpenWrt:/# [ 62.574003] br-lan: port 4(lan4) entered disabled state | |
| [ 62.581098] device lan1 left promiscuous mode | |
| [ 62.585549] br-lan: port 1(lan1) entered disabled state | |
| [ 62.615254] device lan2 left promiscuous mode | |
| [ 62.619678] br-lan: port 2(lan2) entered disabled state | |
| [ 62.646777] device lan3 left promiscuous mode | |
| [ 62.651187] br-lan: port 3(lan3) entered disabled state | |
| [ 62.678551] device lan4 left promiscuous mode | |
| [ 62.682957] br-lan: port 4(lan4) entered disabled state | |
| [ 62.708249] mt7530 mdio-bus:00 lan4: Link is Down | |
| [ 62.781359] mtk_soc_eth 1b100000.ethernet eth0: Link is Down | |
| [ 62.787839] mtk_soc_eth 1b100000.ethernet: PPE table busy | |
| [ 66.927903] reboot: Restarting system | |
| F0: 102B 0000 | |
| F6: 0000 0000 | |
| V0: 0000 0000 [0001] | |
| 00: 0000 0000 | |
| BP: 0000 0041 [0000] | |
| G0: 0190 0000 | |
| T0: 0000 036D [000F] | |
| Jump to BL | |
| UNIVPLL_CON0 = 0xFE000000!!! | |
| mt_pll_init: Set pll frequency for 25M crystal | |
| RAM_CONSOLE preloader last status: 0x0 0x0 0x0 0x0 0x0 0x0 | |
| [PMIC_WRAP]wrap_init pass,the return value=0. | |
| [pmic_init] Preloader Start.................. | |
| [pmic_init] MT6380 CHIP Code, reg_val = 0, 1:E2 0:E3 | |
| [pmic_init] Done................... | |
| Chip part number:7622B | |
| MT7622 Version: 1.2.8, (iPA) | |
| SSC OFF | |
| mt_pll_post_init: mt_get_cpu_freq = 1350000Khz | |
| mt_pll_post_init: mt_get_mem_freq = 1600000Khz | |
| mt_pll_post_init: mt_get_bus_freq = 1119920Khz | |
| [PLFM] Init I2C: OK(0) | |
| [BLDR] Build Time: 20200522-165358 | |
| ==== Dump RGU Reg ======== | |
| RGU MODE: 14 | |
| RGU LENGTH: FFE0 | |
| RGU STA: 40000000 | |
| RGU INTERVAL: FFF | |
| RGU SWSYSRST: 8000 | |
| ==== Dump RGU Reg End ==== | |
| RGU: g_rgu_satus:2 | |
| mtk_wdt_mode_config mode value=10, tmp:22000010 | |
| PL RGU RST: ?? | |
| SW reset with bypass power key flag | |
| Find bypass powerkey flag | |
| WDT NONRST=0x20000000 | |
| WDT IRQ_EN=0x340003 | |
| RGU mtk_wdt_init:MTK_WDT_DEBUG_CTL(590200F3) | |
| [EMI] MDL number = 2 | |
| [EMI] DRAMC calibration start | |
| [EMI] DRAMC calibration end | |
| [EMI]rank size auto detect | |
| [EMI]start_addr[0x40000000]=0x12345678, test_addr[0x48000000]= 0xEDCBA987 | |
| [EMI]start_addr[0x40000000]=0x12345678, test_addr[0x50000000]= 0xEDCBA987 | |
| [EMI]start_addr[0x40000000]=0xEDCBA987, test_addr[0x60000000]= 0xEDCBA987 | |
| [EMI]rank0 size: 0x20000000 | |
| [MEM] complex R/W mem test pass | |
| RAM_CONSOLE wdt status (0x2)=0x2 | |
| [BBT] BMT.v2 is found at 0x3FF | |
| [PLFM] Init Boot Device: OK(0) | |
| [PART] blksz: 2048B | |
| [PART] [0x0000000000000000-0x000000000007FFFF] "PRELOADER" (256 blocks) | |
| [PART] [0x0000000000080000-0x00000000000BFFFF] "tee1" (128 blocks) | |
| [PART] [0x00000000000C0000-0x000000000013FFFF] "lk" (256 blocks) | |
| Device APC domain init setup: | |
| Domain Setup (0x0) | |
| Domain Setup (0x0) | |
| Device APC domain after setup: | |
| Domain Setup (0x0) | |
| Domain Setup (0x0) | |
| [PART] Image with part header | |
| [PART] name : U-Boot | |
| [PART] addr : 41E00000h mode : -1 | |
| [PART] size : 342676 | |
| [PART] magic: 58881688h | |
| [PART] load "lk" from 0x00000000000C0200 (dev) to 0x41E00000 (mem) [SUCCESS] | |
| [PART] load speed: 16731KB/s, 342676 bytes, 20ms | |
| load lk (ret=0) | |
| [PART] Image with part header | |
| [PART] name : atf | |
| [PART] addr : FFFFFFFFh mode : -1 | |
| [PART] size : 57936 | |
| [PART] magic: 58881688h | |
| [PART] load "tee1" from 0x0000000000080200 (dev) to 0x43000DC0 (mem) [SUCCESS] | |
| [PART] load speed: 14144KB/s, 57936 bytes, 4ms | |
| load tee1 (ret=0) | |
| [BLDR] bldr load tee part ret=0x0, addr=0x43001000 | |
| [BLDR] boot part. not found | |
| [BLDR] part_load_images ret=0x0 | |
| [BLDR] Others, jump to ATF | |
| [BLDR] jump to 0x41E00000 | |
| [BLDR] <0x41E00000>=0xEA00000F | |
| [BLDR] <0x41E00004>=0xE59FF014 | |
| U-Boot 2014.04-rc1 Version: 1.0.0.1 (Jul 21 2020 - 12:07:36) | |
| static declaration g_total_rank_size = 0x1F000000 | |
| DRAM: 496 MiB | |
| NAND: Recognize SNAND: ID [e5 71 ], Device Name [FM35X1GA], Page Size [2048]B Spare Size [64]B Total Size [128]MB | |
| [mtk_snand] probe successfully! | |
| [BBT] BMT.v2 is found at 0x3ff | |
| 128 MiB | |
| First booting, write default data (s_env) to flash... | |
| [mtk_nand_erase_hw] mtk_nand_erase_hw @4249, ret:0x40. page:0x680 | |
| [mtk_nand_erase_hw] mtk_nand_erase_hw @4249, ret:0x40. page:0x700 | |
| In: serial | |
| Out: serial | |
| Err: serial | |
| Net: mtk_eth | |
| Uip activated | |
| [?25l[2J[1;1H[1;1H[2K[2;1H *** U-Boot SPI NAND ***[0K[3;1H[2K[14;1H[2K[15;1H Press UP/DOWN to move or Press 1~8 to choose, ENTER to select[0K[16;1H[2K[4;1H 1. System Load Linux to SDRAM via TFTP.[5;1H 2. System Load Linux Kernel then write to Flash via TFTP.[6;1H [7m3. Boot master system code via Flash.[0m[7;1H 4. Boot slave system code via Flash.[8;1H 5. System Load U-Boot then write to Flash via TFTP.[9;1H 6. System Load U-Boot then write to Flash via Serial.[10;1H 7. System Load ATF then write to Flash via TFTP.[11;1H 8. System Load Preloader then write to Flash via TFTP.[12;1H U-Boot console[14;1H Hit any key to stop autoboot: 3 2 1 0 [14;1H[2K[?25h[2J[1;1H | |
| NAND read: device 0 offset 0x500000, size 0x2000 | |
| 8192 bytes read: OK | |
| [do_read_image_blks] This is a FIT image,img_size = 0x32b5b0 | |
| [do_read_image_blks] img_blks = 0x657 | |
| [do_read_image_blks] img_align_size = 0x32b800 | |
| NAND read: device 0 offset 0x500000, size 0x32b800 | |
| 3323904 bytes read: OK | |
| bootm flag=0, states=70f | |
| ## Loading kernel from FIT Image at 4007ff28 ... | |
| Using 'config@1' configuration | |
| Trying 'kernel@1' kernel subimage | |
| Description: ARM64 OpenWrt Linux-5.10.10 | |
| Type: Kernel Image | |
| Compression: lzma compressed | |
| Data Start: 0x40080010 | |
| Data Size: 3297480 Bytes = 3.1 MiB | |
| Architecture: AArch64 | |
| OS: Linux | |
| Load Address: 0x44000000 | |
| Entry Point: 0x44000000 | |
| Hash algo: crc32 | |
| Hash value: 0ea838a0 | |
| Hash algo: sha1 | |
| Hash value: 3d8ff929f59ace0ac54c134c7c8f9519d2325287 | |
| Verifying Hash Integrity ... crc32+ sha1+ OK | |
| ## Loading fdt from FIT Image at 4007ff28 ... | |
| Using 'config@1' configuration | |
| Trying 'fdt@1' fdt subimage | |
| Description: ARM64 OpenWrt linksys_e8450 device tree blob | |
| Type: Flat Device Tree | |
| Compression: uncompressed | |
| Data Start: 0x403a5218 | |
| Data Size: 23948 Bytes = 23.4 KiB | |
| Architecture: AArch64 | |
| Hash algo: crc32 | |
| Hash value: ae8c250d | |
| Hash algo: sha1 | |
| Hash value: 87f597bb6915a4c1d40a521a542f545f1b5291b4 | |
| Verifying Hash Integrity ... crc32+ sha1+ OK | |
| Booting using the fdt blob at 0x403a5218 | |
| Uncompressing Kernel Image ... OK | |
| Loading Device Tree to 5cf09000, end 5cf11d8b ... OK | |
| Starting kernel ... | |
| [ATF][ 5.256136]save kernel info | |
| [ATF][ 5.259073]Kernel_EL2 | |
| [ATF][ 5.261743]Kernel is 64Bit | |
| [ATF][ 5.264831]pc=0x44000000, r0=0x5cf09000, r1=0x0 | |
| INFO: BL3-1: Preparing for EL3 exit to normal world, Kernel | |
| INFO: BL3-1: Next image address = 0x44000000 | |
| INFO: BL3-1: Next image spsr = 0x3c9 | |
| [ATF][ 5.282529]el3_exit | |
| [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] | |
| [ 0.000000] Linux version 5.10.10 (fiore@fiore-FISSO-UBUNTU20) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 8.4.0 r15688-374f24fef4) 8.4.0, GNU ld (GNU Binutils) 2.34) #0 SMP Thu Feb 4 12:16:06 2021 | |
| [ 0.000000] Machine model: Linksys E8450 | |
| [ 0.000000] Zone ranges: | |
| [ 0.000000] DMA [mem 0x0000000040000000-0x000000005fffffff] | |
| [ 0.000000] DMA32 empty | |
| [ 0.000000] Normal empty | |
| [ 0.000000] Movable zone start for each node | |
| [ 0.000000] Early memory node ranges | |
| [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff] | |
| [ 0.000000] node 0: [mem 0x0000000043030000-0x000000005fffffff] | |
| [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff] | |
| [ 0.000000] On node 0 totalpages: 131024 | |
| [ 0.000000] DMA zone: 2048 pages used for memmap | |
| [ 0.000000] DMA zone: 0 pages reserved | |
| [ 0.000000] DMA zone: 131024 pages, LIFO batch:31 | |
| [ 0.000000] psci: probing for conduit method from DT. | |
| [ 0.000000] psci: PSCIv0.2 detected in firmware. | |
| [ 0.000000] psci: Using standard PSCI v0.2 function IDs | |
| [ 0.000000] psci: Trusted OS migration not required | |
| [ 0.000000] percpu: Embedded 20 pages/cpu s44568 r8192 d29160 u81920 | |
| [ 0.000000] pcpu-alloc: s44568 r8192 d29160 u81920 alloc=20*4096 | |
| [ 0.000000] pcpu-alloc: [0] 0 [0] 1 | |
| [ 0.000000] Detected VIPT I-cache on CPU0 | |
| [ 0.000000] CPU features: detected: ARM erratum 845719 | |
| [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration | |
| [ 0.000000] CPU features: detected: ARM erratum 843419 | |
| [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 128976 | |
| [ 0.000000] Kernel command line: console=ttyS0,115200 rootdelay=1 rootfstype=squashfs earlyprintk mtdparts=master | |
| [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) | |
| [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) | |
| [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off | |
| [ 0.000000] Memory: 495172K/524096K available (6782K kernel code, 832K rwdata, 1996K rodata, 448K init, 290K bss, 28924K reserved, 0K cma-reserved) | |
| [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 | |
| [ 0.000000] rcu: Hierarchical RCU implementation. | |
| [ 0.000000] rcu: CONFIG_RCU_FANOUT set to non-default value of 32. | |
| [ 0.000000] Tracing variant of Tasks RCU enabled. | |
| [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. | |
| [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 | |
| [ 0.000000] GIC: GICv2 detected, but range too small and irqchip.gicv2_force_probe not set | |
| [ 0.000000] random: get_random_bytes called from start_kernel+0x340/0x48c with crng_init=0 | |
| [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys). | |
| [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns | |
| [ 0.000003] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns | |
| [ 0.000163] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=50000) | |
| [ 0.000173] pid_max: default: 32768 minimum: 301 | |
| [ 0.000253] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) | |
| [ 0.000261] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) | |
| [ 0.001229] rcu: Hierarchical SRCU implementation. | |
| [ 0.001320] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build | |
| [ 0.001506] smp: Bringing up secondary CPUs ... | |
| [ 0.001817] Detected VIPT I-cache on CPU1 | |
| [ 0.001862] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] | |
| [ 0.001922] smp: Brought up 1 node, 2 CPUs | |
| [ 0.001930] SMP: Total of 2 processors activated. | |
| [ 0.001934] CPU features: detected: 32-bit EL0 Support | |
| [ 0.001939] CPU features: detected: CRC32 instructions | |
| [ 0.002056] CPU: All CPU(s) started at EL2 | |
| [ 0.002067] alternatives: patching kernel code | |
| [ 0.005130] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns | |
| [ 0.005146] futex hash table entries: 512 (order: 3, 32768 bytes, linear) | |
| [ 0.005230] pinctrl core: initialized pinctrl subsystem | |
| [ 0.005662] NET: Registered protocol family 16 | |
| [ 0.006258] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations | |
| [ 0.006285] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations | |
| [ 0.006308] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations | |
| [ 0.006587] thermal_sys: Registered thermal governor 'fair_share' | |
| [ 0.006592] thermal_sys: Registered thermal governor 'bang_bang' | |
| [ 0.006597] thermal_sys: Registered thermal governor 'step_wise' | |
| [ 0.006601] thermal_sys: Registered thermal governor 'user_space' | |
| [ 0.006845] ASID allocator initialised with 65536 entries | |
| [ 0.035908] SCSI subsystem initialized | |
| [ 0.036034] libata version 3.00 loaded. | |
| [ 0.036245] usbcore: registered new interface driver usbfs | |
| [ 0.036279] usbcore: registered new interface driver hub | |
| [ 0.036310] usbcore: registered new device driver usb | |
| [ 0.036845] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 | |
| [ 0.038989] clocksource: Switched to clocksource arch_sys_counter | |
| [ 0.039578] NET: Registered protocol family 2 | |
| [ 0.039890] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) | |
| [ 0.039905] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) | |
| [ 0.039938] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) | |
| [ 0.039999] TCP: Hash tables configured (established 4096 bind 4096) | |
| [ 0.040081] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) | |
| [ 0.040098] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) | |
| [ 0.040278] NET: Registered protocol family 1 | |
| [ 0.040301] PCI: CLS 0 bytes, default 64 | |
| [ 0.041844] workingset: timestamp_bits=46 max_order=17 bucket_order=0 | |
| [ 0.044018] squashfs: version 4.0 (2009/01/31) Phillip Lougher | |
| [ 0.044030] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. | |
| [ 0.076442] mtk-tphy 1a0c4000.usb-phy: failed to get ref_clk(id-1) | |
| [ 0.080397] mt-pmic-pwrap 10001000.pwrap: unexpected interrupt int=0x1 | |
| [ 0.094667] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled | |
| [ 0.095423] printk: console [ttyS0] disabled | |
| [ 0.095491] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 23, base_baud = 1562500) is a 16550A | |
| [ 0.681198] printk: console [ttyS0] enabled | |
| [ 0.685943] 11004000.serial: ttyS1 at MMIO 0x11004000 (irq = 24, base_baud = 1562500) is a 16550A | |
| [ 0.695486] 1100c000.serial: ttyS2 at MMIO 0x1100c000 (irq = 28, base_baud = 17499995) is a MediaTek BTIF | |
| [ 0.705146] serial serial0: tty port ttyS2 registered | |
| [ 0.710498] cacheinfo: Unable to detect cache hierarchy for CPU 0 | |
| [ 0.717073] mtk-ecc 1100e000.ecc: probed | |
| [ 0.722782] spi-nand spi2.0: Fidelix SPI NAND was found. | |
| [ 0.728132] spi-nand spi2.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 | |
| [ 0.737711] [BBT] BMT.v2 is found at 0x3ff | |
| [ 0.741996] 12 fixed-partitions partitions found on MTD device spi2.0 | |
| [ 0.748441] Creating 12 MTD partitions on "spi2.0": | |
| [ 0.753316] 0x000000000000-0x000000080000 : "Preloader" | |
| [ 0.759636] 0x000000080000-0x0000000c0000 : "ATF" | |
| [ 0.765062] 0x0000000c0000-0x000000140000 : "u-boot" | |
| [ 0.771067] 0x000000140000-0x0000001c0000 : "u-boot-env" | |
| [ 0.777372] 0x0000001c0000-0x0000002c0000 : "factory" | |
| [ 0.784023] 0x000000300000-0x000000320000 : "devinfo" | |
| [ 0.789643] 0x000000320000-0x000000340000 : "senv" | |
| [ 0.795038] 0x000000360000-0x000000380000 : "bootseq" | |
| [ 0.800666] 0x000000500000-0x000002300000 : "firmware1" | |
| [ 0.832507] random: fast init done | |
| [ 0.844750] 2 fit-fw partitions found on MTD device firmware1 | |
| [ 0.850501] Creating 2 MTD partitions on "firmware1": | |
| [ 0.855553] 0x000000000000-0x000000340000 : "kernel" | |
| [ 0.860938] 0x000000340000-0x000001e00000 : "rootfs" | |
| [ 0.866342] mtd: device 10 (rootfs) set to be root filesystem | |
| [ 0.872257] 1 squashfs-split partitions found on MTD device rootfs | |
| [ 0.878444] 0x000000880000-0x000001e00000 : "rootfs_data" | |
| [ 0.884292] 0x000002300000-0x000004100000 : "firmware2" | |
| [ 0.924503] 0x000004100000-0x000005a00000 : "data" | |
| [ 0.958524] 0x000005a00000-0x000006e00000 : "mfg" | |
| [ 0.987257] libphy: Fixed MDIO Bus: probed | |
| [ 1.014986] libphy: mdio: probed | |
| [ 1.018791] mtk_soc_eth 1b100000.ethernet: generated random MAC address 62:25:db:90:a4:04 | |
| [ 1.027244] mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xffffffc011660000, irq 37 | |
| [ 1.037594] rtc_mt7622 10212800.rtc: registered as rtc0 | |
| [ 1.042861] rtc_mt7622 10212800.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) | |
| [ 1.052637] mtk-wdt 10212000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0) | |
| [ 1.063396] NET: Registered protocol family 10 | |
| [ 1.068416] Segment Routing with IPv6 | |
| [ 1.072133] NET: Registered protocol family 17 | |
| [ 1.076702] 8021q: 802.1Q VLAN Support v1.8 | |
| [ 1.090783] mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges: | |
| [ 1.097342] mtk-pcie 1a143000.pcie: Parsing ranges property... | |
| [ 1.103181] mtk-pcie 1a143000.pcie: MEM 0x0020000000..0x0027ffffff -> 0x0020000000 | |
| [ 1.127706] mtk-pcie 1a143000.pcie: PCI host bridge to bus 0000:00 | |
| [ 1.133892] pci_bus 0000:00: root bus resource [bus 00-ff] | |
| [ 1.139374] pci_bus 0000:00: root bus resource [mem 0x20000000-0x27ffffff] | |
| [ 1.146242] pci_bus 0000:00: scanning bus | |
| [ 1.150292] pci 0000:00:00.0: [14c3:3258] type 01 class 0x060400 | |
| [ 1.156324] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x1ffffffff 64bit pref] | |
| [ 1.164984] pci_bus 0000:00: fixups for bus | |
| [ 1.169170] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0 | |
| [ 1.175867] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring | |
| [ 1.183876] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1 | |
| [ 1.190666] pci_bus 0000:01: scanning bus | |
| [ 1.194883] pci 0000:01:00.0: [14c3:7915] type 00 class 0x000280 | |
| [ 1.201063] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref] | |
| [ 1.208387] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref] | |
| [ 1.215711] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref] | |
| [ 1.223669] pci 0000:01:00.0: supports D1 D2 | |
| [ 1.227936] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold | |
| [ 1.234569] pci 0000:01:00.0: PME# disabled | |
| [ 1.239055] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) | |
| [ 1.264134] pci_bus 0000:01: fixups for bus | |
| [ 1.268322] pci_bus 0000:01: bus scan returning with max=01 | |
| [ 1.273893] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 | |
| [ 1.280508] pci_bus 0000:00: bus scan returning with max=01 | |
| [ 1.286092] pci 0000:00:00.0: BAR 0: no space for [mem size 0x200000000 64bit pref] | |
| [ 1.293745] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x200000000 64bit pref] | |
| [ 1.301743] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff] | |
| [ 1.308530] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit pref] | |
| [ 1.316354] pci 0000:01:00.0: BAR 2: assigned [mem 0x20100000-0x20103fff 64bit pref] | |
| [ 1.324179] pci 0000:01:00.0: BAR 4: assigned [mem 0x20104000-0x20104fff 64bit pref] | |
| [ 1.332001] pci 0000:00:00.0: PCI bridge to [bus 01] | |
| [ 1.336967] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff] | |
| [ 1.343778] pci 0000:00:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256 | |
| [ 1.352331] pci 0000:01:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 128 | |
| [ 1.360826] pcieport 0000:00:00.0: of_irq_parse_pci: failed with rc=-22 | |
| [ 1.367437] pcieport 0000:00:00.0: assign IRQ: got 0 | |
| [ 1.372404] pcieport 0000:00:00.0: enabling device (0000 -> 0002) | |
| [ 1.378509] pcieport 0000:00:00.0: enabling bus mastering | |
| [ 1.384373] mtk-pcie 1a145000.pcie: host bridge /pcie@1a145000 ranges: | |
| [ 1.390908] mtk-pcie 1a145000.pcie: Parsing ranges property... | |
| [ 1.396746] mtk-pcie 1a145000.pcie: MEM 0x0028000000..0x002fffffff -> 0x0028000000 | |
| [ 1.504911] mtk-pcie 1a145000.pcie: Port1 link down | |
| [ 1.509881] mtk-pcie 1a145000.pcie: PCI host bridge to bus 0001:00 | |
| [ 1.516064] pci_bus 0001:00: root bus resource [bus 00-ff] | |
| [ 1.521548] pci_bus 0001:00: root bus resource [mem 0x28000000-0x2fffffff] | |
| [ 1.528418] pci_bus 0001:00: scanning bus | |
| [ 1.533479] pci_bus 0001:00: fixups for bus | |
| [ 1.537660] pci_bus 0001:00: bus scan returning with max=00 | |
| [ 1.543501] mtk_hsdma 1b007000.dma-controller: Using 3 as missing dma-requests property | |
| [ 1.551708] mtk_hsdma 1b007000.dma-controller: MediaTek HSDMA driver registered | |
| [ 1.596133] libphy: dsa slave smi: probed | |
| [ 1.601032] mt7530 mdio-bus:00 lan1 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] (irq=POLL) | |
| [ 1.611543] mt7530 mdio-bus:00 lan2 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] (irq=POLL) | |
| [ 1.621966] mt7530 mdio-bus:00 lan3 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] (irq=POLL) | |
| [ 1.632377] mt7530 mdio-bus:00 lan4 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] (irq=POLL) | |
| [ 1.642775] mt7530 mdio-bus:00 wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY] (irq=POLL) | |
| [ 1.652808] mt7530 mdio-bus:00: configuring for fixed/2500base-x link mode | |
| [ 1.660378] mt7530 mdio-bus:00: Link is Up - 2.5Gbps/Full - flow control rx/tx | |
| [ 1.660990] DSA: tree 0 setup | |
| [ 1.671332] xhci-mtk 1a0c0000.usb: xHCI Host Controller | |
| [ 1.676599] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 1 | |
| [ 1.685651] xhci-mtk 1a0c0000.usb: hcc params 0x01403198 hci version 0x96 quirks 0x0000000000210010 | |
| [ 1.694738] xhci-mtk 1a0c0000.usb: irq 33, io mem 0x1a0c0000 | |
| [ 1.700823] hub 1-0:1.0: USB hub found | |
| [ 1.704590] hub 1-0:1.0: 2 ports detected | |
| [ 1.708813] xhci-mtk 1a0c0000.usb: xHCI Host Controller | |
| [ 1.714044] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 2 | |
| [ 1.721442] xhci-mtk 1a0c0000.usb: Host supports USB 3.0 SuperSpeed | |
| [ 1.727738] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. | |
| [ 1.736062] hub 2-0:1.0: USB hub found | |
| [ 1.739824] hub 2-0:1.0: 1 port detected | |
| [ 1.744552] UBI error: no valid UBI magic found inside mtd13 | |
| [ 1.750846] Waiting 1 sec before mounting root device... | |
| [ 2.790956] VFS: Mounted root (squashfs filesystem) readonly on device 31:10. | |
| [ 2.798290] Freeing unused kernel memory: 448K | |
| [ 2.807016] Run /sbin/init as init process | |
| [ 2.811110] with arguments: | |
| [ 2.814068] /sbin/init | |
| [ 2.816769] earlyprintk | |
| [ 2.819557] with environment: | |
| [ 2.822687] HOME=/ | |
| [ 2.825043] TERM=linux | |
| [ 2.827743] mtdparts=master | |
| [ 3.130956] init: Console is alive | |
| [ 3.134486] init: - watchdog - | |
| [ 3.520077] random: crng init done | |
| [ 3.580253] kmodloader: loading kernel modules from /etc/modules-boot.d/* | |
| [ 3.659232] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver | |
| [ 3.666405] ehci-fsl: Freescale EHCI Host controller driver | |
| [ 3.672593] ehci-platform: EHCI generic platform driver | |
| [ 3.679401] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver | |
| [ 3.686095] ohci-platform: OHCI generic platform driver | |
| [ 3.693436] kmodloader: done loading kernel modules from /etc/modules-boot.d/* | |
| [ 3.704843] init: - preinit - | |
| [ 4.170546] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode | |
| [ 4.179021] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx | |
| [ 4.187722] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready | |
| [ 4.195021] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode | |
| [ 4.202126] 8021q: adding VLAN 0 to HW filter on device lan1 | |
| Press the [f] key and hit [enter] to enter failsafe mode | |
| Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level | |
| [ 8.428688] jffs2: notice: (828) jffs2_build_xattr_subsystem: complete building xattr subsystem, 7 of xdatum (6 unchecked, 1 orphan) and 8 of xref (1 dead, 0 orphan) found. | |
| [ 8.447117] mount_root: switching to jffs2 overlay | |
| [ 8.459067] overlayfs: upper fs does not support tmpfile. | |
| [ 8.476997] overlayfs: "xino" feature enabled using 32 upper inode bits. | |
| [ 8.488024] urandom-seed: Seeding with /etc/urandom.seed | |
| [ 8.615736] procd: - early - | |
| [ 8.618648] procd: - watchdog - | |
| Failed to connect to ubus | |
| [ 9.177675] procd: - watchdog - | |
| [ 9.250383] procd: - ubus - | |
| [ 9.336233] procd: - init - | |
| Please press Enter to activate this console. | |
| [ 9.576577] urngd: v1.0.2 started. | |
| [ 9.700848] kmodloader: loading kernel modules from /etc/modules.d/* | |
| [ 9.861311] Loading modules backported from Linux version v5.10-rc6-0-gb65054597872 | |
| [ 9.869005] Backport generated by backports.git v5.10-rc6-1-0-g3a9d70a3 | |
| [ 9.915104] xt_time: kernel timezone is -0000 | |
| [ 9.958302] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' | |
| [ 9.968450] mt7915e 0000:01:00.0: assign IRQ: got 145 | |
| [ 9.973635] pci 0000:00:00.0: enabling bus mastering | |
| [ 9.978635] mt7915e 0000:01:00.0: enabling device (0000 -> 0002) | |
| [ 9.984744] mt7915e 0000:01:00.0: enabling bus mastering | |
| [ 10.174296] mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a | |
| [ 10.174296] | |
| [ 10.174519] mt7915e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20200819112315a | |
| [ 10.174519] | |
| [ 10.439222] jffs2: notice: (829) check_node_data: wrong data CRC in data node at 0x00ba0000: read 0x21b422b9, calculated 0x2dc75145. | |
| [ 10.641698] mt7622-wmac 18000000.wmac: N9 Firmware Version: 2.0, Build Time: 20200131180931 | |
| [ 10.900934] mt7915e 0000:01:00.0: WM Firmware Version: ____000000, Build Time: 20200819112349 | |
| [ 11.032348] mt7915e 0000:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20200819112407 | |
| [ 11.183234] PPP generic driver version 2.4.2 | |
| [ 11.190628] NET: Registered protocol family 24 | |
| [ 11.212400] kmodloader: done loading kernel modules from /etc/modules.d/* | |
| [ 14.992082] mtk_soc_eth 1b100000.ethernet eth0: Link is Down | |
| [ 15.000514] mtk_soc_eth 1b100000.ethernet: PPE table busy | |
| [ 15.011132] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode | |
| [ 15.019716] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx | |
| [ 15.019733] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready | |
| [ 15.035906] device eth0 entered promiscuous mode | |
| [ 15.043022] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode | |
| [ 15.050428] 8021q: adding VLAN 0 to HW filter on device lan1 | |
| [ 15.058542] br-lan: port 1(lan1) entered blocking state | |
| [ 15.063813] br-lan: port 1(lan1) entered disabled state | |
| [ 15.069966] device lan1 entered promiscuous mode | |
| [ 15.081251] mt7530 mdio-bus:00 lan2: configuring for phy/gmii link mode | |
| [ 15.092904] 8021q: adding VLAN 0 to HW filter on device lan2 | |
| [ 15.101258] br-lan: port 2(lan2) entered blocking state | |
| [ 15.106571] br-lan: port 2(lan2) entered disabled state | |
| [ 15.112426] device lan2 entered promiscuous mode | |
| [ 15.121469] mt7530 mdio-bus:00 lan3: configuring for phy/gmii link mode | |
| [ 15.128700] 8021q: adding VLAN 0 to HW filter on device lan3 | |
| [ 15.139176] br-lan: port 3(lan3) entered blocking state | |
| [ 15.144456] br-lan: port 3(lan3) entered disabled state | |
| [ 15.150470] device lan3 entered promiscuous mode | |
| [ 15.159271] mt7530 mdio-bus:00 lan4: configuring for phy/gmii link mode | |
| [ 15.166378] 8021q: adding VLAN 0 to HW filter on device lan4 | |
| [ 15.169236] mt7530 mdio-bus:00 lan4: Link is Up - 1Gbps/Full - flow control rx/tx | |
| [ 15.174259] br-lan: port 4(lan4) entered blocking state | |
| [ 15.184752] br-lan: port 4(lan4) entered disabled state | |
| [ 15.190877] device lan4 entered promiscuous mode | |
| [ 15.197928] br-lan: port 4(lan4) entered blocking state | |
| [ 15.203160] br-lan: port 4(lan4) entered forwarding state | |
| [ 15.208985] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready | |
| [ 15.220374] mt7530 mdio-bus:00 wan: configuring for phy/gmii link mode | |
| [ 15.227593] 8021q: adding VLAN 0 to HW filter on device wan | |
| BusyBox v1.31.1 () built-in shell (ash) | |
| _______ ________ __ | |
| | |.-----.-----.-----.| | | |.----.| |_ | |
| | - || _ | -__| || | | || _|| _| | |
| |_______|| __|_____|__|__||________||__| |____| | |
| |__| W I R E L E S S F R E E D O M | |
| ----------------------------------------------------- | |
| OpenWrt SNAPSHOT, r15688-374f24fef4 | |
| ----------------------------------------------------- | |
| === WARNING! ===================================== | |
| There is no root password defined on this device! | |
| Use the "passwd" command to set up a new password | |
| in order to prevent unauthorized SSH logins. | |
| -------------------------------------------------- | |
| root@OpenWrt:/# md5sum /root/random.file | |
| 58b802ed8d52b18b8552d3a9999337f8 /root/random.file | |
| root@OpenWrt:/# cat /root/random.file.md5; | |
| 8506b23e9ea97fb6bb325f74c324bf8a /root/random.file | |
| root@OpenWrt:/# |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment