Skip to content

Instantly share code, notes, and snippets.

@DieterReuter

DieterReuter/gist:25de06cbf3c5372ce071656cfa1c1610

Created February 12, 2017 14:24
Show Gist options
  • Save DieterReuter/25de06cbf3c5372ce071656cfa1c1610 to your computer and use it in GitHub Desktop.
Save DieterReuter/25de06cbf3c5372ce071656cfa1c1610 to your computer and use it in GitHub Desktop.
Download ZIP
Beelink GT1, Booting HypriotOS/arm64, complete bootlog from UART console
Raw
gistfile1.txt
$ sudo minicom
Welcome to minicom 2.7
OPTIONS: I18n
Compiled on Aug 18 2014, 09:30:17.
Port /dev/ttyUSB0, 14:19:21
Press CTRL-A Z for help on special keys
GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 144463
BL2 Built : 19:58:22, Aug 31 2016.
gxl g54c8aee - xiaobo.gu@droid05
set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00015400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a9a00
NOTICE: BL3-1: v1.0(debug):2e39a99
NOTICE: BL3-1: Built : 16:36:21, Sep 20 2016
aml log : bl31 normal boot !
wdt: reset registers!
[Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
OPS=0x82
fc c2 9 21 fb ca c 14 7e b4 40 63 [0.392270 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gd267f87 (Jan 19 2017 - 16:49:10)
DRAM: 2 GiB
Relocation Offset is: 76ec9000
register usb cfg[0][1] = 0000000077f5f5d8
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000073ec96b0
aml_priv->desc_buf = 0x0000000073ecb9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073ece270,dt_addr=0000000073ed9270
parts: 11
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000080000000 1
09: cache 0000000020000000 2
10: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 80000000 1
13: data d7c00000 2c5400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
reboot_mode=normal
hpd_state=0
cvbs performance type = 6, table = 0
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3d851000
[CANVAS]canvas init
[CANVAS]addr=0x3d851000 width=5760, height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
get_cpu_id flag_12bit=1
SARADC open channel(0).
SARADC channel(0) is 0x3ca, Out of range(0x0~0x50)!
saradc - saradc sub-system
Usage:
saradc saradc open <channel> - open a SARADC channel
saradc close - close the SARADC
saradc getval - get the value in current channel
saradc get_in_range <min> <max> - return 0 if current value in the range of current channel
get_cpu_id flag_12bit=1
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
(Re)start USB...
USB0: USB3.0 XHCI init start
Register 3000140 NbrPorts 3
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
card in
[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading s905_autoscript
888 bytes read in 5 ms (172.9 KiB/s)
## Executing script at 01020000
U-Boot 2015.01-gd267f87 (Jan 19 2017 - 16:49:10)
aarch64-none-elf-gcc (crosstool-NG linaro-1.13.1-4.8-2013.11 - Linaro GCC 2013.10) 4.8.3 20131111 (p)
GNU ld (crosstool-NG linaro-1.13.1-4.8-2013.11 - Linaro GCC 2013.10) 2.23.2.20130610 Linaro 2013.10-4
EnableSelinux=disabled
aml_dt=gxm_q201_2g
baudrate=115200
bootargs=rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xe
bootcmd=run start_autoscript;
bootdelay=5
bootfromnand=0
bootfromrecovery=0
bootup_offset=0x1162748
bootup_size=0x5eec36
cmdline_keys=if keyman init 0x1234; then if keyman read usid ${loadaddr} str; then setenv bootargs $;
cvbs_drv=0
cvbsmode=576cvbs
display_bpp=24
display_color_bg=0
display_color_fg=0xffff
display_color_index=24
display_height=576
display_layer=osd1
display_width=720
dtb_mem_addr=0x1000000
ethact=dwmac.c9410000
ethaddr=00:15:18:01:81:31
factory_reset_poweroff_protect=echo wipe_data=${wipe_data}; echo wipe_cache=${wipe_cache};if test ${
fb_addr=0x3d800000
fb_height=1080
fb_width=1920
fdt_high=0x20000000
filesize=378
firstboot=0
gatewayip=10.18.9.1
hdmimode=1080p60hz
hostname=arm_gxbb
init_display=osd open;osd clear;imgread pic logo bootup $loadaddr;bmp display $bootup_offset;bmp scae
initargs=rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0x
ipaddr=10.18.9.97
jtag=apao
loadaddr=1080000
mac=86:37:20:48:cb:3e
maxcpus=8
netmask=255.255.255.0
outputmode=576cvbs
preboot=run factory_reset_poweroff_protect;run upgrade_check;run init_display;run storeargs;run upgr;
reboot_mode=normal
recovery_from_flash=setenv bootargs ${bootargs} aml_dt=${aml_dt} recovery_part={recovery_part} recovi
recovery_from_sdcard=setenv bootargs ${bootargs} aml_dt=${aml_dt} recovery_part={recovery_part} reco;
recovery_from_udisk=setenv bootargs ${bootargs} aml_dt=${aml_dt} recovery_part={recovery_part} recov;
recovery_offset=0
recovery_part=recovery
sdc_burning=sdc_burn ${sdcburncfg}
sdcburncfg=aml_sdc_burn.ini
serverip=10.18.9.113
start_autoscript=if usb start ; then run start_usb_autoscript;fi;if mmcinfo; then run start_mmc_auto;
start_mmc_autoscript=if fatload mmc 0 1020000 s905_autoscript; then autoscr 1020000; fi
start_usb_autoscript=if fatload usb 0 1020000 s905_autoscript; then autoscr 1020000; fi
stderr=serial
stdin=serial
stdout=serial
storeargs=setenv bootargs ${initargs} androidboot.selinux=${EnableSelinux} logo=${display_layer},loa;
storeboot=if imgread kernel boot ${loadaddr}; then bootm ${loadaddr}; fi;run update;
switch_bootmode=get_rebootmode;if test ${reboot_mode} = factory_reset; then run recovery_from_flash;;
try_auto_burn=update 700 750;
update=run usb_burning; run sdc_burning; if mmcinfo; then run recovery_from_sdcard;fi;if usb start 0;
upgrade_check=echo upgrade_step=${upgrade_step}; if itest ${upgrade_step} == 3; then run init_displa;
upgrade_key=saradc open 0; if saradc get_in_range 0x0 0x50; then echo detect upgrade key; run update;
upgrade_step=2
usb_burning=update 1000
wipe_cache=successful
wipe_data=successful
Environment size: 5164/65532 bytes
** Bad device usb 0 **
reading uInitrd
3930724 bytes read in 218 ms (17.2 MiB/s)
reading zImage
16367544 bytes read in 896 ms (17.4 MiB/s)
reading dtb.img
** Unable to read file dtb.img **
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxm platform: q201 variant: 2g
dtb 0 soc: gxm plat: q201 vari: 1g
dtb 1 soc: gxm plat: q201 vari: 2g
Find match dtb: 1
## Loading init Ramdisk from Legacy Image at 13000000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
Data Size: 3930660 Bytes = 3.7 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
## Flattened Device Tree blob at 01000000
Booting using the fdt blob at 0x1000000
Loading Ramdisk to 73af7000, end 73eb6a24 ... OK
Loading Device Tree to 000000001fff2000, end 000000001ffff1ca ... OK
signature:
fdt_instaboot: no instaboot image
Starting kernel ...
uboot time: 5319989 us
domain-0 init dvfs: 4
domain-1 init dvfs: 4
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-amlogics905x-gac75c6f-dirty (root@user-VirtualBox) (gcc versi7
[ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000@0] no prop version_code
[ 0.000000@0] fdt Reserved memory table:
[ 0.000000@0] linux,di: 0x000000007d300000 - 0x000000007f100000 (30 MiB)
[ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007d300000, size 30 MiB
[ 0.000000@0] linux,ion-dev: 0x0000000079300000 - 0x000000007d300000 (64 MiB)
[ 0.000000@0] linux,ppmgr: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] linux,codec_mm_cma: 0x0000000067800000 - 0x0000000073800000 (192 MiB)
[ 0.000000@0] linux,picdec: 0x0000000079300000 - 0x0000000079300000 (0 MiB)
[ 0.000000@0] Reserved memory: incorrect alignment of CMA region
[ 0.000000@0] linux,codec_mm_reserved: 0x0000000075200000 - 0x0000000079300000 (65 MiB)
[ 0.000000@0] fdt Reserved memory total: 354 MiB
[ 0.000000@0] cma: Reserved 8 MiB at 74800000
[ 0.000000@0] psci: probing function IDs from device-tree
[ 0.000000@0] PERCPU: Embedded 13 pages/cpu @ffffffc075166000 s20864 r8192 d24192 u53248
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 510280
[ 0.000000@0] Kernel command line: root=LABEL=ROOTFS rootflags=data=writeback rw console=ttyS0,11
[ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000@0] Memory: 1641772K/2077696K available (10134K kernel code, 895K rwdata, 3764K rodata,)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
[ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff80423cc800 ( 35 MB)
[ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc07f100000 ( 2033 MB)
[ 0.000000@0] .init : 0xffffffc001e14000 - 0xffffffc001f3b180 ( 1181 kB)
[ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001e13a24 ( 13903 kB)
[ 0.000000@0] .data : 0xffffffc001f3c000 - 0xffffffc00201bfb8 ( 896 kB)
[ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01e12fff]
[ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000@0] arch_multi_cluster:1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] RCU debugfs-based tracing is enabled.
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[ 0.000034@0] meson_bc_timer: mclk->mux_reg =ffffff8000014990,mclk->reg =ffffff8000016994
[ 0.000356@0] Console: colour dummy device 80x25
[ 0.000878@0] console [tty0] enabled
[ 0.000900@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 Bo)
[ 0.000924@0] pid_max: default: 32768 minimum: 301
[ 0.001036@0] Security Framework initialized
[ 0.001068@0] AppArmor: AppArmor initialized
[ 0.001118@0] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.001134@0] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.003561@0] device-tree: Duplicate name in /efusekey, renamed to "key0#1"
[ 0.003592@0] device-tree: Duplicate name in /efusekey, renamed to "key1#1"
[ 0.003610@0] device-tree: Duplicate name in /efusekey, renamed to "key2#1"
[ 0.003627@0] device-tree: Duplicate name in /efusekey, renamed to "key3#1"
[ 0.006422@0] Initializing cgroup subsys debug
[ 0.006443@0] Initializing cgroup subsys freezer
[ 0.006491@0] ftrace: allocating 35111 entries in 138 pages
[ 0.050327@0] /cpus/cpu@0: Missing clock-frequency property
[ 0.050361@0] /cpus/cpu@1: Missing clock-frequency property
[ 0.050377@0] /cpus/cpu@2: Missing clock-frequency property
[ 0.050393@0] /cpus/cpu@3: Missing clock-frequency property
[ 0.050409@0] /cpus/cpu@100: Missing clock-frequency property
[ 0.050426@0] /cpus/cpu@101: Missing clock-frequency property
[ 0.050444@0] /cpus/cpu@102: Missing clock-frequency property
[ 0.050462@0] /cpus/cpu@103: Missing clock-frequency property
[ 0.050480@0] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 0.090100@0] Meson chip version = RevA (22:A - 82:0)
[ 0.110212@1] CPU1: Booted secondary processor
[ 0.130211@2] CPU2: Booted secondary processor
[ 0.150212@3] CPU3: Booted secondary processor
[ 0.170235@4] CPU4: Booted secondary processor
[ 0.190235@5] CPU5: Booted secondary processor
[ 0.210250@6] CPU6: Booted secondary processor
[ 0.230262@7] CPU7: Booted secondary processor
[ 0.230348@0] Brought up 8 CPUs
[ 0.230431@0] SMP: Total of 8 processors activated.
[ 0.230967@0] devtmpfs: initialized
[ 0.236221@2] sched: registering cpufreq notifiers for scale-invariant loads
[ 0.236352@2] instabooting: 0
[ 0.242329@2] xor: measuring software checksum speed
[ 0.340053@2] 8regs : 2291.600 MB/sec
[ 0.440081@2] 8regs_prefetch: 2158.800 MB/sec
[ 0.540109@2] 32regs : 2615.200 MB/sec
[ 0.640137@2] 32regs_prefetch: 2364.400 MB/sec
[ 0.640149@2] xor: using function: 32regs (2615.200 MB/sec)
[ 0.640168@2] pinctrl core: initialized pinctrl subsystem
[ 0.640798@2] regulator-dummy: no parameters
[ 0.641528@2] NET: Registered protocol family 16
[ 0.643251@2] cpuidle: using governor menu
[ 0.643494@2] aml_vdac_init: module init
[ 0.643655@0] register canvas platform driver
[ 0.643760@2] register rdma platform driver
[ 0.644477@2] vdso: 2 pages (1 code, 1 data) at base ffffffc001f44000
[ 0.644529@2] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.644905@2] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.645876@2] software IO TLB [mem 0x64400000-0x64800000] (4MB) mapped at [ffffffc064400000-fffff]
[ 0.646352@2] aml_i2c version: 20140813
[ 0.646597@2] i2c-core: driver [pmu4] using legacy resume method
[ 0.646688@3] codec_mm:codec_mm_module_init
[ 0.646924@2] aml_watch_point_probe, in
[ 0.647368@2] gxbb_mpll_clk: register mpll_clk_out0 success done
[ 0.647388@2] gxbb_mpll_clk: register mpll_clk_out1 success done
[ 0.647403@2] gxbb_mpll_clk: register mpll_clk_out2 success done
[ 0.647606@2] clk_sys: register PLL sys_pll success done
[ 0.647627@2] gxl_clk: [ xtal ] ->clockrate: 24000000Hz
[ 0.647639@2] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz
[ 0.647652@2] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz
[ 0.647664@2] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz
[ 0.647676@2] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz
[ 0.647688@2] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz
[ 0.647700@2] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz
[ 0.647712@2] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz
[ 0.647724@2] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz
[ 0.647760@2] gxl_clk: clock initialization complete
[ 0.647954@2] clkmsr: Gxl msr_clk_reg0=ffffff800006475c,msr_clk_reg2=ffffff8000066764
[ 0.650455@2] aml_iomap: amlogic iomap probe done
[ 0.651139@2] pinmux-gxl c1109880.pinmux: Init pinux probe!
[ 0.652266@3] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
[ 0.652748@2] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.652783@2] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[ 0.652957@2] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.652984@2] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[ 0.659621@2] codec_mm has 2 memory regions
[ 0.659677@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.659701@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.659819@3] codec_mm has 2 memory regions
[ 0.659844@3] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
[ 0.659866@3] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
[ 0.661875@2] vpu: driver version: v02
[ 0.661924@2] vpu: load vpu_clk: 666667000Hz(7)
[ 0.662020@2] vpu: vpu_probe OK
[ 0.663568@2] tv_vout: tvout_probe
[ 0.663598@2] tv_vout: major number 254 for disp
[ 0.663609@2] vout_notify: vout_register_server
[ 0.663620@2] tv_vout: register tv module server ok
[ 0.663705@2] tv_vout: tvout_probe OK
[ 0.664297@2] canvas_probe reg=00000000c8838000,size=400
[ 0.664336@2] canvas maped reg_base =ffffff8000188000
[ 0.668175@2] rdma_probe
[ 0.927682@3] bio: create slab <bio-0> at 0
[ 1.090781@0] raid6: int64x1 484 MB/s
[ 1.260914@0] raid6: int64x2 716 MB/s
[ 1.430965@0] raid6: int64x4 1035 MB/s
[ 1.600995@0] raid6: int64x8 1198 MB/s
[ 1.771067@0] raid6: neonx1 771 MB/s
[ 1.941157@0] raid6: neonx2 1201 MB/s
[ 2.111259@0] raid6: neonx4 1563 MB/s
[ 2.281340@0] raid6: neonx8 1725 MB/s
[ 2.281351@0] raid6: using algorithm neonx8 (1725 MB/s)
[ 2.281363@0] raid6: using intx1 recovery algorithm
[ 2.282165@3] SCSI subsystem initialized
[ 2.282685@3] usbcore: registered new interface driver usbfs
[ 2.282794@0] usbcore: registered new interface driver hub
[ 2.282929@3] usbcore: registered new device driver usb
[ 2.283830@3] i2c-gpio i2c_gpio.38: using pins 172 (SDA) and 173 (SCL)
[ 2.283975@0] Linux video capture interface: v2.00
[ 2.284177@0] pps_core: LinuxPPS API ver. 1 registered
[ 2.284191@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linu>
[ 2.284269@3] PTP clock support registered
[ 2.284859@0] hdmitx: system: amhdmitx_init
[ 2.284878@0] hdmitx: system: Ver: 2014May6
[ 2.285062@0] hdmitx: system: amhdmitx_probe
[ 2.285404@3] hdmitx: system: not find match init-data
[ 2.285422@3] hdmitx: system: not find match pwr-ctl
[ 2.285434@3] hdmitx hpd irq = 89
[ 2.285892@3] hdmitx20: Mapped PHY: 0xc0800000
[ 2.285915@3] hdmitx20: Mapped PHY: 0xc1104400
[ 2.285941@3] hdmitx20: Mapped PHY: 0xc8100000
[ 2.285953@3] hdmitx20: Mapped PHY: 0xc8834000
[ 2.285965@3] hdmitx20: Mapped PHY: 0xc883a000
[ 2.285976@3] hdmitx20: Mapped PHY: 0xc883c000
[ 2.285990@3] hdmitx20: Mapped PHY: 0xd0100000
[ 2.286002@3] hdmitx20: Mapped PHY: 0xda83a000
[ 2.286247@3] avmute set to 1
[ 2.286579@3] vout_serve: vout_init_module
[ 2.286713@3] vout_serve: no matched vout_init mode
[ 2.286801@3] vinfo: error: invalid vinfo. current vmode is not supported
[ 2.286814@3] vout_serve: create vout attribute OK
[ 2.286825@3] vout_serve: meson_vout_probe OK
[ 2.286996@0] logo: logo_init
[ 2.287097@3] Advanced Linux Sound Architecture Driver Initialized.
[ 2.287710@3] NetLabel: Initializing
[ 2.287729@3] NetLabel: domain hash size = 128
[ 2.287738@3] NetLabel: protocols = UNLABELED CIPSOv4
[ 2.287787@3] NetLabel: unlabeled traffic allowed by default
[ 2.288820@3] Switched to clocksource arch_sys_counter
[ 2.301775@3] FS-Cache: Loaded
[ 2.301922@3] AppArmor: AppArmor Filesystem Enabled
[ 2.312434@3] NET: Registered protocol family 2
[ 2.312933@3] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 2.313092@3] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 2.313350@3] TCP: Hash tables configured (established 16384 bind 16384)
[ 2.313426@3] TCP: reno registered
[ 2.313442@3] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 2.313492@3] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 2.313711@3] NET: Registered protocol family 1
[ 2.313970@0] RPC: Registered named UNIX socket transport module.
[ 2.313990@0] RPC: Registered udp transport module.
[ 2.314001@0] RPC: Registered tcp transport module.
[ 2.314011@0] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.314239@0] aml_wifi wifi.33: [wifi_dev_probe] no power_on_pin2
[ 2.314255@0] aml_wifi wifi.33: [wifi_dev_probe] set pwm as 32k output
[ 2.314314@0] aml_wifi wifi.33: [wifi_dev_probe] interrupt_pin=241
[ 2.314329@0] aml_wifi wifi.33: [wifi_dev_probe] irq_num=100, irq_trigger_type=1
[ 2.314347@0] aml_wifi wifi.33: [wifi_dev_probe] power_on_pin=240
[ 2.314360@0] aml_wifi wifi.33: [wifi_dev_probe] clock_32k_pin=0
[ 2.314713@0] aml_wifi wifi.33: [wifi_setup_dt] wifi_setup_dt
[ 2.314763@0] aml_wifi wifi.33: [wifi_setup_dt] interrupt_pin(241)
[ 2.314786@0] aml_wifi wifi.33: [wifi_setup_dt] power_on_pin(240)
[ 2.315094@3] Unpacking initramfs...
[ 2.473186@3] Freeing initrd memory: 3836K (ffffffc073af7000 - ffffffc073eb6000)
[ 2.476083@3] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 2.476190@3] audit: initializing netlink subsys (disabled)
[ 2.476260@3] audit: type=2000 audit(2.440:1): initialized
[ 2.477160@0] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 2.484257@0] VFS: Disk quotas dquot_6.5.2
[ 2.484508@0] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 2.487595@0] NFS: Registering the id_resolver key type
[ 2.487645@0] Key type id_resolver registered
[ 2.487657@0] Key type id_legacy registered
[ 2.487673@0] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 2.488403@0] msgmni has been set to 3614
[ 2.489744@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 2.489775@0] io scheduler noop registered (default)
[ 2.489787@0] io scheduler deadline registered
[ 2.489974@0] io scheduler cfq registered
[ 2.491582@0] meson-rng c8834000.rng: hwrng registered
[ 2.495389@0] loop: module loaded
[ 2.496368@3] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 2.497498@0] tun: Universal TUN/TAP device driver, 1.6
[ 2.497523@0] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 2.627047@0] libphy: stmmac: probed
[ 2.627076@0] eth0: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
[ 2.627091@0] eth0: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07)
[ 2.627551@0] PPP generic driver version 2.4.2
[ 2.627842@1] NET: Registered protocol family 24
[ 2.628007@0] usbcore: registered new interface driver cdc_ether
[ 2.628117@0] usbcore: registered new interface driver net1080
[ 2.628212@1] usbcore: registered new interface driver cdc_subset
[ 2.628308@0] usbcore: registered new interface driver zaurus
[ 2.628425@0] usbcore: registered new interface driver cdc_ncm
[ 2.628999@0] platform c9000000.dwc3: Driver dwc3 requests probe deferral
[ 2.629193@0] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.629209@0] ehci-h20ahb: H20AHB-EHCI Host Controller driver
[ 2.629448@1] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.629839@0] usbcore: registered new interface driver cdc_acm
[ 2.629858@0] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.629987@1] usbcore: registered new interface driver usb-storage
[ 2.630222@0] usbcore: registered new interface driver usbserial
[ 2.630321@1] usbcore: registered new interface driver usbserial_generic
[ 2.630410@0] usbserial: USB Serial support registered for generic
[ 2.630504@0] usbcore: registered new interface driver pl2303
[ 2.630592@1] usbserial: USB Serial support registered for pl2303
[ 2.631213@0] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_bas0
[ 2.631455@1] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
[ 2.631488@1] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_bas0
[ 2.631968@1] mousedev: PS/2 mouse device common for all mice
[ 2.632427@1] usbcore: registered new interface driver xpad
[ 2.632681@0] i2c /dev entries driver
[ 2.633034@0] usbcore: registered new interface driver uvcvideo
[ 2.633051@0] USB Video Class driver (1.1.1)
[ 2.633935@1] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[ 2.634226@1] CPUidle arm64: cpuidle init start!!
[ 2.634730@1] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.634907@0] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.635187@0] usbcore: registered new interface driver usbhid
[ 2.635203@0] usbhid: USB HID core driver
[ 2.636060@0] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff80001f64c0
[ 2.636106@0] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a mest
[ 2.636136@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
[ 4.154948@0] console [ttyS0] enabled
[ 4.159068@0] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff80001f84c0
[ 4.165654@0] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a mesot
[ 4.175670@0] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: d0078000, ctrl: 0
[ 4.183570@0] dwc_otg_driver_probe host only, not probe usb_otg!!!
[ 4.189927@0] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c00]
[ 4.199632@0] meson-gpu-clkgen: probe of c883c000.gpu_clk failed with error -16
[ 4.207109@1] hdmitx: system: hdmitx_hdcp_init
[ 4.211461@0] ESM HLD: Initializing...
[ 4.214967@0] ESM HLD: Registering device range 'esm'...
[ 4.220252@0] ESM HLD: Device range 'esm' has been registered.
[ 4.226005@0] ESM HLD: Creating class /sys/class/elliptic...
[ 4.231728@0] ESM HLD: The class /sys/class/elliptic has been created.
[ 4.238080@0] ESM HLD: Creating device 'esm'...
[ 4.242784@1] ESM HLD: Device 'esm' has been created.
[ 4.247567@1] ESM HLD: Done initializing the HLD driver.
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[ 4.268890@0] aml_vrtc rtc.32: rtc core: registered aml_vrtc as rtc0
[ 4.270359@0] secmon has 1 memory regions
[ 4.273621@0] secmon: share in base: 0xffffff8000404000, share out base: 0xffffff8000406000
[ 4.281894@0] secmon secmon.4: assigned reserved memory node linux,secmon ok
[ 4.288853@0] secmon: probe done
[ 4.292379@0] storage: storage in base: 0xffffff8001600000
[ 4.297471@0] storage: storage out base: 0xffffff8001680000
[ 4.303002@0] storage: storage block base: 0xffffff8001700000
[ 4.308683@0] storage: probe done!
[ 4.312593@0] aml_sd_emmc_probe: line 3558
[ 4.316104@0] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRr
[ 4.326121@0] aml_sd_emmc_reg_init 1146
[ 4.329398@0] get property: ocr_avail, value:0x00200080
[ 4.335767@0] get property: f_min, value:300000
[ 4.341899@0] get property: f_max, value:100000000
[ 4.348274@0] get property: max_req_size, value:0x00020000
[ 4.354753@0] get property: pinname, str:emmc
[ 4.360540@0] get property: card_type, value:1
[ 4.366231@0] get property: gpio_dat3, str:
[ 4.371664@0] get property: hw_reset, str:
[ 4.377117@0] emmc:pdata->caps = c0000d47
[ 4.381061@0] emmc:pdata->caps2 = 18060
[ 4.384854@0] storage 1, boot 1
[ 4.387948@0] get_storage_dev return 1
[ 4.428824@1] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 4.429060@1] aml_sd_emmc_probe: line 3558
[ 4.433496@1] aml_sd_emmc_reg_init 1146
[ 4.436930@1] get property: ocr_avail, value:0x00200080
[ 4.443366@1] get property: f_min, value:400000
[ 4.449478@1] get property: f_max, value:100000000
[ 4.455854@1] get property: max_req_size, value:0x00020000
[ 4.462334@1] get property: irq_in, value:3
[ 4.468015@1] get property: irq_out, value:5
[ 4.473722@1] get property: gpio_cd, str:
[ 4.479148@1] get property: pinname, str:sd
[ 4.484748@1] get property: jtag_pin, str:
[ 4.490188@1] get property: card_type, value:5
[ 4.495875@1] get property: gpio_dat3, str:
[ 4.501328@1] sd:pdata->caps = 7
[ 4.504498@1] sd:pdata->caps2 = 0
[ 4.539021@1] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 4.539059@4] [aml_is_card_insert] card IN
[ 4.543308@1] aml_sd_emmc_probe: line 3558
[ 4.547702@1] aml_sd_emmc_reg_init 1146
[ 4.551188@1] get property: ocr_avail, value:0x00200080
[ 4.557594@1] get property: f_min, value:400000
[ 4.563725@1] get property: f_max, value:200000000
[ 4.570107@1] get property: max_req_size, value:0x00020000
[ 4.576572@1] get property: pinname, str:sdio
[ 4.582354@1] get property: card_type, value:3
[ 4.588085@1] sdio:pdata->caps = 7810f
[ 4.591754@1] sdio:pdata->caps2 = 0
[ 4.615555@3] emmc: BKOPS_EN bit is not set
[ 4.624704@3] emmc: trying cali 0-th time(s)
[ 4.627800@3] emmc: delay[0]= 4600 padding= 2, bidx=4
[ 4.628345@3] emmc: delay[1]= 4400 padding= 3, bidx=4
[ 4.633370@3] emmc: delay[2]= 4400 padding= 3, bidx=4
[ 4.633375@1] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
[ 4.633722@1] ion_dev has 1 memory regions
[ 4.640404@4] normal card in
[ 4.650656@1] fb: osd_init_module
[ 4.650783@1] fb: viu vsync irq: 35
[ 4.650789@1] fb: failed to init reserved memory
[ 4.650807@1] tv_vout: tv_set_current_vmode[759]fps_target_mode=16
[ 4.650810@1] tv_vout: mode is 16,sync_duration_den=1,sync_duration_num=60
[ 4.650818@1] tv_vout: TV mode 1080p60hz selected.
[ 4.650823@1]
[ 4.650823@1] vdac_enable: on:0,module_sel:8
[ 4.650829@1]
[ 4.650829@1] vdac_enable: on:0,module_sel:8
[ 4.650835@1] tv_vout: new mode =1080p60hz set ok
[ 4.650837@1] vout_serve: vinfo mode is: 1080p60hz
[ 4.651076@1] osd_rdma: osd_rdma_init: rdma_table p=0x74846000,op=0x74846000 , v=0xffffff800041e00
[ 4.651078@1] osd_rdma: osd rdma request irq as second interrput function!
[ 4.651095@1] fb: osd_probe vinfo:ffffffc001fbd8a8
[ 4.651100@1] fb: init fbdev bpp is:32
[ 4.725388@0] fb: use ion buffer for fb memory
[ 4.725399@3] emmc: delay[3]= 4800 padding= 1, bidx=4
[ 4.725401@3] emmc: delay[4]= 4800 padding= 1, bidx=4
[ 4.725403@3] emmc: delay[5]= 4800 padding= 1, bidx=4
[ 4.725406@3] emmc: delay[6]= 4600 padding= 2, bidx=4
[ 4.725408@3] emmc: delay[7]= 4800 padding= 1, bidx=4
[ 4.725410@3] emmc: calibration result @ 0: max(4800), min(4400)
[ 4.725413@3] emmc: line_delay =0x1000221, max_cal_result =4800
[ 4.725415@3] emmc: base_index_max 4, base_index_min 4
[ 4.725421@3] emmc: clk 100000000 SDR mode tuning start
[ 4.726037@0] meson-fb meson-fb.16: create ion_client ffffffc0653226c0, handle=ffffffc0635810c0
[ 4.726041@0] meson-fb meson-fb.16: ion memory(0): created fb at 0x0000000079300000, size 24 MiB
[ 4.726048@0] fb: Frame buffer memory assigned at
[ 4.726048@0] fb: 0, phy: 0x0000000079300000, vir:0xffffff80018c4000, size=24900K
[ 4.726048@0]
[ 4.726051@0] fb: ---------------clear fb0 memory ffffff80018c4000
[ 4.726154@3] emmc: rx_tuning_result[0] = 10
[ 4.726681@3] emmc: rx_tuning_result[1] = 10
[ 4.727208@3] emmc: rx_tuning_result[2] = 10
[ 4.727739@3] emmc: rx_tuning_result[3] = 10
[ 4.728269@3] emmc: rx_tuning_result[4] = 10
[ 4.728782@3] emmc: rx_tuning_result[5] = 10
[ 4.729316@3] emmc: rx_tuning_result[6] = 10
[ 4.729844@3] emmc: rx_tuning_result[7] = 10
[ 4.730371@3] emmc: rx_tuning_result[8] = 10
[ 4.730424@3] emmc: best_win_start =0, best_win_size =9
[ 4.730427@3] emmc: sd_emmc_regs->gclock=0x100024a,sd_emmc_regs->gadjust=0x42000
[ 4.730430@3] emmc: gclock =0x100024a, gdelay=0x1000221, gadjust=0x42000
[ 4.730757@3] emmc: new HS200 MMC card at address 0001
[ 4.731269@1] emmc: clock 100000000, 8-bit-bus-width
[ 4.731269@1]
[ 4.731270@1] mmcblk0: emmc:0001 NCard 14.4 GiB
[ 4.731412@1] mmcblk0boot0: emmc:0001 NCard partition 1 4.00 MiB
[ 4.731545@1] mmcblk0boot1: emmc:0001 NCard partition 2 4.00 MiB
[ 4.731677@1] mmcblk0rpmb: emmc:0001 NCard partition 3 4.00 MiB
[ 4.732380@3] mmcblk0: unknown partition table
[ 4.733086@3] [mmc_read_partition_tbl] mmc read partition OK!
[ 4.733087@3] add_emmc_partition
[ 4.733321@3] [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
[ 4.733489@3] [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
[ 4.733653@3] [mmcblk0p03] cache offset 0x000006c00000, size 0x000020000000
[ 4.733811@3] [mmcblk0p04] env offset 0x000027400000, size 0x000000800000
[ 4.733968@3] [mmcblk0p05] logo offset 0x000028400000, size 0x000002000000
[ 4.734135@3] [mmcblk0p06] recovery offset 0x00002ac00000, size 0x000002000000
[ 4.734286@3] [mmcblk0p07] rsv offset 0x00002d400000, size 0x000000800000
[ 4.734441@3] [mmcblk0p08] tee offset 0x00002e400000, size 0x000000800000
[ 4.734602@3] [mmcblk0p09] crypt offset 0x00002f400000, size 0x000002000000
[ 4.734770@3] [mmcblk0p10] misc offset 0x000031c00000, size 0x000002000000
[ 4.734931@3] [mmcblk0p11] instaboot offset 0x000034400000, size 0x000020000000
[ 4.735090@3] [mmcblk0p12] boot offset 0x000054c00000, size 0x000002000000
[ 4.735250@3] [mmcblk0p13] system offset 0x000057400000, size 0x000080000000
[ 4.735416@3] [mmcblk0p14] data offset 0x0000d7c00000, size 0x0002c5400000
[ 4.735450@3] card key: card_blk_probe.
[ 4.735454@3] emmc_key_init:527 emmc key lba_start:0x12020,lba_end:0x12220
[ 4.735457@3] emmc key: emmc_key_init:552 ok.
[ 4.735670@3] amlmmc_dtb_init: register dtb chardev
[ 4.735750@3] amlmmc_dtb_init: register dtb chardev OK
[ 4.735751@3] Exit aml_emmc_partition_ops OK.
[ 4.736867@3] mmcblk0boot1: unknown partition table
[ 4.737607@0] fb: osd[0] canvas.idx =0x40
[ 4.737609@0] fb: osd[0] canvas.addr=0x79300000
[ 4.737611@0] fb: osd[0] canvas.width=7680
[ 4.737612@0] fb: osd[0] canvas.height=3240
[ 4.737614@0] fb: osd[0] frame.width=1920
[ 4.737615@0] fb: osd[0] frame.height=1080
[ 4.737717@3] mmcblk0boot0: unknown partition table
[ 4.737981@3] clear_emmc_wait_flag
[ 4.813642@3] sd: new high speed SDHC card at address aaaa
[ 4.814060@3] sd: clock 50000000, 4-bit-bus-width
[ 4.814060@3]
[ 4.814060@3] mmcblk1: sd:aaaa SL08G 7.40 GiB
[ 4.815147@3] mmcblk1: p1 p2
[ 4.854951@0] Console: switching to colour frame buffer device 240x67
[ 5.328823@0] fb: osd probe OK
[ 5.333257@1] ge2d: ge2d_init_module
[ 5.337402@1] ge2d: ge2d_dev major:242
[ 5.342002@0] ge2d: ge2d clock is 400 MHZ
[ 5.346041@0] ge2d: ge2d: pdev=ffffffc065276800, irq=182, rstc=0xffffffc0635819c0, clk=ffffffc0650
[ 5.353908@0] ge2d: mapped phy: 0xd0160000
[ 5.357928@0] ge2d: ge2d start monitor
[ 5.361944@2] ge2d: ge2d workqueue monitor start
[ 5.362307@1] codec:Amlogic A/V streaming port init
[ 5.364196@0] codec:get gate demux control ok ffffffc0653ed8c0
[ 5.364201@0] codec:get gate parser_top control ok ffffffc0653ed940
[ 5.364206@0] codec:get gate vpu_intr control ok ffffffc0653ed9c0
[ 5.364212@0] codec:get gate vdec control ok ffffffc0653eda40
[ 5.364836@0] codec:[tsync_pcr_init]init success.
[ 5.364838@0] codec:amvideocap_init_module
[ 5.364968@0] codec:amvideocap_probe,amvideocap
[ 5.364971@0] codec:use cma buf.
[ 5.364973@0] codec:amvideocap_dev_register
[ 5.366736@0] amvenc_avc_probe -- reserved memory config fail.
[ 5.366739@0] amvenc_avc - cma memory pool size: 40 MB
[ 5.366761@0] encode_wq_init.
[ 5.366765@0] encode start monitor.
[ 5.366820@1] encode workqueue monitor start.
[ 5.367301@0] jpegenc module init
[ 5.367612@1] codec:picdec_driver_probe called.
[ 5.367615@1] picdec has 1 memory regions
[ 5.367640@1] codec:picdec_driver_probe done.
[ 5.368793@1] codec:create_ge2d_work_queue video task ok
[ 5.369269@0] codec:used fix clk for vdec clk source!
[ 5.369275@0] codec:register clk_set_setting cpu[34]
[ 5.369597@0] vpu_init
[ 5.369760@0] vpu_probe
[ 5.369764@0] HevcEnc reserved memory config fail.
[ 5.369767@0] HevcEnc - cma memory pool size: 64 MB
[ 5.369770@0] HevcEnc - wave420l_irq: 219
[ 5.369808@0] vpu base address get from platform driver physical base addr=0xc8810000, virtual ba0
[ 5.370177@0] success to probe vpu device with video memory from cma
[ 5.370336@1] DI: di_module_init ok.
[ 5.370341@1] DI: di_module_init: major 235
[ 5.370556@0] DI: di_probe
[ 5.370742@1] deinterlace has 1 memory regions
[ 5.370781@1] deinterlace deinterlace.26: assigned reserved memory node linux,di ok
[ 5.370804@1] di_irq:78,timerc_irq:38
[ 5.534308@1] rdma_register, rdma_table_addr ffffff8000581000 rdma_table_addr_phy 74848000 reg_bu0
[ 5.544174@1] rdma_register success, handle 1 table_size 8192
[ 5.549591@1] DI: di_probe allocate rdma channel 1.
[ 5.554415@1] DI: DI hw version 2.
[ 5.559169@1] 0x000000db:Y=db,U=0,V=0
[ 5.563860@1] 0x000000dc:Y=dc,U=0,V=0
[ 5.568498@1] 0x000000dd:Y=dd,U=0,V=0
[ 5.573147@1] 0x000000de:Y=de,U=0,V=0
[ 5.577738@1] 0x000000df:Y=df,U=0,V=0
[ 5.582280@1] 0x000000e0:Y=e0,U=0,V=0
[ 5.586762@1] 0x000000e1:Y=e1,U=0,V=0
[ 5.591278@1] 0x000000e2:Y=e2,U=0,V=0
[ 5.595737@1] 0x000000e3:Y=e3,U=0,V=0
[ 5.600199@1] 0x000000f0:Y=f0,U=0,V=0
[ 5.604639@1] 0x000000f1:Y=f1,U=0,V=0
[ 5.609072@1] 0x000000f2:Y=f2,U=0,V=0
[ 5.613442@1] 0x000000f3:Y=f3,U=0,V=0
[ 5.617759@1] 0x000000f4:Y=f4,U=0,V=0
[ 5.622017@1] 0x000000f5:Y=f5,U=0,V=0
[ 5.626211@1] 0x000000f6:Y=f6,U=0,V=0
[ 5.630369@1] 0x000000f7:Y=f7,U=0,V=0
[ 5.634486@1] 0x000000f8:Y=f8,U=0,V=0
[ 5.638560@1] 0x000000f9:Y=f9,U=0,V=0
[ 5.642560@1] 0x000000fa:Y=fa,U=0,V=0
[ 5.646468@1] 0x000000fb:Y=fb,U=0,V=0
[ 5.650346@1] 0x000000fc:Y=fc,U=0,V=0
[ 5.654367@1] DI: di_probe here.
[ 5.658639@1] efusekeynum: 4
[ 5.662491@1] efusekeyname: mac offset: 0 size: 6
[ 5.667017@1] efusekeyname: mac_bt offset: 6 size: 6
[ 5.673421@1] efusekeyname: mac_wifi offset: 12 size: 6
[ 5.679802@1] efusekeyname: usid offset: 18 size: 16
[ 5.686586@1] efuse efuse.10: probe OK!
[ 5.690761@0] key unify config unifykey-num is 14
[ 5.694654@0] key unify fact unifykey-num is 14
[ 5.699129@0] aml_unifykeys_probe:1273=============unifykey_devno:e900000
[ 5.706211@1] 6unifykey: device unifykeys created ok
[ 5.711050@0] 6aml_unifykeys_init done!
[ 5.714788@0] PPMGRDRV: warn: ppmgr module init func called
[ 5.720409@0] PPMGRDRV: err: ppmgr_driver_probe called
[ 5.725316@0] ppmgr has 1 memory regions
[ 5.729247@0] PPMGRDRV: info: ppmgr_dev major:232
[ 5.734295@1] PPMGRDRV: info: ppmgr_probe done
[ 5.738777@0] amlogic rfkill init
[ 5.742777@0] enter bt_probe of_node
[ 5.746567@0] not get gpio_en
[ 5.750308@0] power on valid level is high
[ 6.169383@1] ionvideo-000: V4L2 device registered as video13
[ 6.176972@1] ionvid: info: Video Technology Magazine Ion Video
[ 6.182876@1] ionvid: info: Capture Board ver 1.0 successfully loaded
[ 6.189251@1] audio_dsp: [dsp]register dsp to char divece(257)
[ 6.195962@1] amaudio: amaudio: driver amaudio succuess!
[ 6.200683@1] amlvid:err: amlvideo_init called
[ 6.204486@2] amlvid:err: amlvideo_create_instance called
[ 6.212220@2] amlvid:err: v4l2_dev.name=:amlvideo-000
[ 6.217229@1] amlvideo-000: V4L2 device registered as video10
[ 6.223178@1] [RX]-hdmirx: hdmirx_init.
[ 6.227171@1] ESM HLD: Initializing...
[ 6.231155@1] ESM HLD: Registering device range 'esm_rx'...
[ 6.235640@1] ESM HLD: Device range 'esm_rx' has been registered.
[ 6.241689@1] ESM HLD: Creating class /sys/class/elliptic_rx...
[ 6.247674@1] ESM HLD: The class /sys/class/elliptic_rx has been created.
[ 6.254339@1] ESM HLD: Creating device 'esm_rx'...
[ 6.259312@2] ESM HLD: Device 'esm_rx' has been created.
[ 6.264266@2] ESM HLD: Done initializing the HLD driver.
[ 6.269568@2] [viuin..]viuin_init_module viuin module init
[ 6.275514@1] [viuin..]viuin_probe probe ok.
[ 6.279369@2] module init
[ 6.283114@2]
[ 6.283114@2] VECM probe start
[ 6.290459@1] aml_vecm_probe: ok
[ 6.294683@1] saradc c1108680.saradc: initialized by BL30
[ 6.298313@1] saradc c1108680.saradc: calibration start:
[ 6.303390@1] saradc c1108680.saradc: nominal=0, value=5
[ 6.308598@1] saradc c1108680.saradc: nominal=256, value=251
[ 6.314226@1] saradc c1108680.saradc: nominal=512, value=500
[ 6.319852@1] saradc c1108680.saradc: nominal=768, value=749
[ 6.325417@1] saradc c1108680.saradc: nominal=1023, value=996
[ 6.331088@1] saradc c1108680.saradc: calibration end: coef=4211
[ 6.337306@2] remote: Driver init
[ 6.341211@2] remote: platform_data g_remote_ao_offset=580
[ 6.345729@2] remote: platform_data irq =228
[ 6.349991@2] remote: set drvdata completed
[ 6.355921@2] remote: device_create_file completed
[ 6.360560@2] input: aml_keypad as /devices/meson-remote.12/input/input0
[ 6.366208@2] remote: input_register_device completed
[ 6.372058@2] remote: set_remote_mode[74]
[ 6.377161@2] remote: remote config major:229
[ 6.381703@2] remote: physical address:0x636b6000
[ 6.386640@2] gpio-key gpio_keypad.48: gpio_key: 0 name(power) pin()
[ 6.391715@2] gpio-key gpio_keypad.48: amlogic_gpio_name_map_num pin 0!::
[ 6.398430@2] gpio-key gpio_keypad.48: gpio_key: 0 power(147)
[ 6.404144@2] gpio-key gpio_keypad.48: start setup_timer
[ 6.409395@2] gpio-key gpio_keypad.48: power key(116) registed.
[ 6.415525@1] input: gpio_keypad as /devices/gpio_keypad.48/input/input1
[ 6.422182@1] gpio-key gpio_keypad.48: gpio keypad register input device completed.
[ 6.429509@1] input input1: gpio keypad major:228
[ 6.435211@1] Sensor: lsm303d_init
[ 6.440271@1] Sensor: stk8313_init
[ 6.444987@1] Sensor: stk831x_init
[ 6.449680@2] Sensor: mxc622x_acc_init
[ 6.454329@1] Sensor: mxc6255xc_acc_init
[ 6.458964@1] Sensor: l3gd20_gyr_init
[ 6.464687@1] cpuinfo: probe done
[ 6.469549@1] defendkey c8834500.defendkey: defendkey_devno:e300000
[ 6.474954@1] defendkey c8834500.defendkey: defendkey: device defendkey created ok
[ 6.482457@1] defendkey: driver init
[ 6.487734@1] input: cec_input as /devices/virtual/input/input2
[ 6.492901@2] cectx aocec: aml_cec_probe(): no hdmirx reg resource
[ 6.498626@2] cectx aocec: aml_cec_probe(): no hhi reg resource
[ 6.504693@2] cectx aocec: aml_cec_probe(): can't find hdmirx
[ 6.510213@2] input input1: key 116 up
[ 6.515837@2] cec: wake up flag:0
[ 6.520939@1] aml_aes_dma c883e000.aml_aes: Aml AES_dma
[ 6.526108@1] aml_tdes_dma c883e000.aml_tdes: Aml TDES_dma
[ 6.531516@2] aml_sha_dma c883e000.aml_sha: Aml SHA1/SHA224/SHA256 dma
[ 6.538930@1] aml_codec_T9015 c8832000.t9015: aml_T9015_audio_codec_probe
[ 6.546955@1] aml_pcm_dai: pcm mode detection =1
[ 6.552158@1] aml_spdif_dai: enterd aml_spdif_play,set_clock:-1,sample_rate=4
[ 6.558290@1] aml_spdif_dai: set normal 512 fs /4 fs
[ 6.563247@1] aml_audio_hw: IEC958 16bit
[ 6.567816@1] hdmitx: audio: aout notify rate 48000
[ 6.572417@1] hdmitx: audio: aout notify size 16
[ 6.576931@1] hdmitx: audio: aout notify format CT_PCM
[ 6.789029@1] aml_snd_card: headphone detection disable=1
[ 6.793635@1] aml_snd_card: no spk event delay time set
[ 6.799190@1] aml_snd_m8_card aml_m8_snd.47: T9015-audio-hifi <-> I2S.40 mapping ok
[ 6.806713@1] aml_snd_m8_card aml_m8_snd.47: dit-hifi <-> SPDIF.41 mapping ok
[ 6.813367@1] aml_pcm: enter aml_pcm_new dai->name: PCM.42 dai->id: 0
[ 6.819771@1] aml_snd_m8_card aml_m8_snd.47: pcm2bt-pcm <-> PCM.42 mapping ok
[ 6.826674@1] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTL
[ 6.834281@1] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
[ 6.843063@1] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTR
[ 6.850648@1] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[ 6.866672@1] aml_snd_card: audio use jtag pinmux as i2s output, read val =0
WARNING: Unimplemented Sip Call: 0x82000036
[ 6.878230@0] GACT probability NOT on
[ 6.883126@0] Mirror/redirect action on
[ 6.887930@0] u32 classifier
[ 6.892707@0] Actions configured
[ 6.897475@0] Netfilter messages via NETLINK v0.30.
[ 6.902372@0] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 6.908436@1] ctnetlink v0.93: registering with nfnetlink.
[ 6.914171@1] xt_time: kernel timezone is -0000
[ 6.919433@1] ipip: IPv4 over IPv4 tunneling driver
[ 6.925427@1] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 6.930807@1] arp_tables: (C) 2002 David S. Miller
[ 6.935962@1] TCP: cubic registered
[ 6.941047@1] Initializing XFRM netlink socket
[ 6.947051@0] NET: Registered protocol family 10
[ 6.953391@1] mip6: Mobile IPv6
[ 6.958565@1] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 6.964059@1] sit: IPv6 over IPv4 tunneling driver
[ 6.970664@1] NET: Registered protocol family 17
[ 6.975855@1] NET: Registered protocol family 15
[ 6.981114@1] Bridge firewalling registered
[ 6.986236@1] l2tp_core: L2TP core driver, V2.0
[ 6.991329@1] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 6.996489@1] l2tp_netlink: L2TP netlink interface
[ 7.001626@1] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 7.007272@1] l2tp_debugfs: L2TP debugfs support
[ 7.012402@1] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 7.018560@1] NET: Registered protocol family 35
[ 7.023746@1] Key type dns_resolver registered
[ 7.029550@1] Registering SWP/SWPB emulation handler
[ 7.037129@1] bio: create slab <bio-1> at 1
[ 7.043466@2] Btrfs loaded
[ 7.048710@2] BTRFS: selftest: Running btrfs free space cache tests
[ 7.054563@2] BTRFS: selftest: Running extent only tests
[ 7.059834@2] BTRFS: selftest: Running bitmap only tests
[ 7.065077@2] BTRFS: selftest: Running bitmap and extent tests
[ 7.070947@2] BTRFS: selftest: Free space cache tests finished
[ 7.076620@2] BTRFS: selftest: Running extent buffer operation tests
[ 7.082754@2] BTRFS: selftest: Running btrfs_split_item tests
[ 7.093036@2] BTRFS: selftest: Running find delalloc tests
[ 7.310340@2] BTRFS: selftest: Running btrfs_get_extent tests
[ 7.315698@2] BTRFS: selftest: Running hole first btrfs_get_extent test
[ 7.418910@2] AppArmor: AppArmor sha1 policy hashing enabled
[ 7.424131@2] regulator-dummy: disabling
[ 8.131806@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 8.137048@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 8.145180@1] xhci-hcd xhci-hcd.0.auto: irq 62, io mem 0xc9000000
[ 8.150970@1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 8.157714@1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.165070@1] usb usb1: Product: xHCI Host Controller
[ 8.170231@1] usb usb1: Manufacturer: Linux 3.14.29 xhci-hcd
[ 8.175653@1] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 8.181473@1] hub 1-0:1.0: USB hub found
[ 8.186626@1] hub 1-0:1.0: 3 ports detected
[ 8.192061@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 8.197229@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 8.205121@1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 8.211894@1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.219225@1] usb usb2: Product: xHCI Host Controller
[ 8.224448@1] usb usb2: Manufacturer: Linux 3.14.29 xhci-hcd
[ 8.229832@1] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 8.235694@3] hub 2-0:1.0: USB hub found
[ 8.240951@3] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 8.248494@7] console [netcon0] enabled
[ 8.254782@7] netconsole: network logging started
[ 8.261037@7] aml_vrtc rtc.32: setting system clock to 2015-01-01 00:00:13 UTC (1420070413)
[ 8.271479@7] gxbb_pm: enter meson_pm_probe!
[ 8.277839@7] gxbb_pm: meson_pm_probe done
[ 8.284554@3] aml-thermal thermal: Frequency table not initialized. Deferring probe...
[ 8.292157@3] platform thermal: Driver aml-thermal requests probe deferral
[ 8.299127@1] aml_istbt_dev_ready NULL
[ 8.304524@1] ALSA device list:
[ 8.309898@1] #0: AML-M8AUDIO
[ 8.315822@1] Freeing unused kernel memory: 1180K (ffffffc001e14000 - ffffffc001f3b000)
[ 8.356177@1] systemd-udevd[2065]: starting version 215
[ 8.362972@1] random: systemd-udevd urandom read with 42 bits of entropy available
[ 9.146941@0] EXT4-fs (mmcblk1p2): mounted filesystem with writeback data mode. Opts: data=writebk
[ 9.454876@5] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINI)
[ 9.470571@5] systemd[1]: Detected architecture 'arm64'.
[ 9.535562@2] systemd[1]: Inserted module 'autofs4'
[ 9.543229@2] systemd[1]: Set hostname to <black-pearl-s912>.
[ 9.576467@2] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 9.788517@5] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: U.
[ 9.807254@5] systemd[1]: Expecting device dev-ttyS0.device...
[ 9.823102@3] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 9.832378@3] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 9.841430@3] systemd[1]: Starting Remote File Systems (Pre).
[ 9.855796@3] systemd[1]: Reached target Remote File Systems (Pre).
[ 9.863607@3] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 9.882006@3] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automoun.
[ 9.893318@3] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 9.903340@3] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 9.913147@3] systemd[1]: Starting Paths.
[ 9.928093@3] systemd[1]: Reached target Paths.
[ 9.935402@3] systemd[1]: Starting Encrypted Volumes.
[ 9.950251@3] systemd[1]: Reached target Encrypted Volumes.
[ 9.957578@3] systemd[1]: Starting Swap.
[ 9.972528@3] systemd[1]: Reached target Swap.
[ 9.979859@3] systemd[1]: Starting Root Slice.
[ 9.994779@3] systemd[1]: Created slice Root Slice.
[ 10.002052@3] systemd[1]: Starting User and Session Slice.
[ 10.017026@3] systemd[1]: Created slice User and Session Slice.
[ 10.024602@3] systemd[1]: Starting Delayed Shutdown Socket.
[ 10.039715@3] systemd[1]: Listening on Delayed Shutdown Socket.
[ 10.047278@3] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 10.063544@3] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 10.072379@3] systemd[1]: Starting Journal Socket (/dev/log).
[ 10.087665@3] systemd[1]: Listening on Journal Socket (/dev/log).
[ 10.095468@3] systemd[1]: Starting udev Control Socket.
[ 10.110563@3] systemd[1]: Listening on udev Control Socket.
[ 10.117993@3] systemd[1]: Starting udev Kernel Socket.
[ 10.133007@3] systemd[1]: Listening on udev Kernel Socket.
[ 10.140345@3] systemd[1]: Starting Journal Socket.
[ 10.155234@3] systemd[1]: Listening on Journal Socket.
[ 10.162555@3] systemd[1]: Starting System Slice.
[ 10.177310@3] systemd[1]: Created slice System Slice.
[ 10.184452@3] systemd[1]: Starting system-getty.slice.
[ 10.199087@3] systemd[1]: Created slice system-getty.slice.
[ 10.206100@3] systemd[1]: Starting system-serial\x2dgetty.slice.
[ 10.221038@3] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 10.228879@3] systemd[1]: Starting Increase datagram queue length...
[ 10.245379@3] systemd[1]: Mounting Huge Pages File System...
[ 10.251528@7] random: nonblocking pool is initialized
[ 10.267958@3] systemd[1]: Starting Create list of required static device nodes for the current ke.
[ 10.316623@3] systemd[1]: Starting Load Kernel Modules...
[ 10.332798@3] systemd[1]: Mounting Debug File System...
[ 10.348559@3] systemd[1]: Starting udev Coldplug all Devices...
[ 10.364348@3] systemd[1]: Mounting POSIX Message Queue File System...
[ 10.385344@3] systemd[1]: Started Set Up Additional Binary Formats.
[ 10.392861@3] systemd[1]: Starting Slices.
[ 10.406636@3] systemd[1]: Reached target Slices.
[ 10.413425@3] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 10.437668@3] systemd[1]: Mounted POSIX Message Queue File System.
[ 10.451680@3] systemd[1]: Mounted Debug File System.
[ 10.465142@3] systemd[1]: Mounted Huge Pages File System.
[ 10.479365@3] systemd[1]: Started Increase datagram queue length.
[ 10.494907@3] systemd[1]: Started Create list of required static device nodes for the current ker.
[ 10.513216@3] systemd[1]: Started Load Kernel Modules.
[ 10.530591@3] systemd[1]: Started Remount Root and Kernel File Systems.
[ 10.570823@3] systemd[1]: Started udev Coldplug all Devices.
[ 10.600986@3] systemd[1]: Started Various fixups to make systemd work better on Debian.
[ 10.610800@3] systemd[1]: Starting Load/Save Random Seed...
[ 10.626902@3] systemd[1]: Mounting Configuration File System...
[ 10.642960@3] systemd[1]: Mounted FUSE Control File System.
[ 10.650114@3] systemd[1]: Starting Apply Kernel Variables...
[ 10.665977@3] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 10.682861@3] systemd[1]: Starting Syslog Socket.
[ 10.697286@3] systemd[1]: Listening on Syslog Socket.
[ 10.704333@3] systemd[1]: Starting Journal Service...
[ 10.727451@3] systemd[1]: Started Journal Service.
[ 10.815642@0] systemd-udevd[2166]: starting version 215
[ 10.876827@3] systemd-journald[2164]: Received request to flush runtime journal from PID 1
[ 11.096549@0] BT_RADIO going: on
[ 11.096552@0] BCM_BT: going ON
[ 11.115344@0] ionvid: info: ionvideo open
[ 11.318843@3] ionvid: info: ionvideo_stop_generating!!!!
[ 11.325096@3] ionvid: info: ionvideo release
[ 12.092893@0] meson_uart c81004c0.[ 12.100998@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M)0
[ 12.136078@1] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
[ 12.136248@1] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
HypriotOS (Debian GNU/Linux 8) black-pearl-s912 ttyS0
black-pearl-s912 login: [ 15.509107@4] libphy: stmmac-0:00 - Link is Up - 1000/Full
HypriotOS (Debian GNU/Linux 8) black-pearl-s912 ttyS0
black-pearl-s912 login:
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment