Created
April 18, 2020 14:41
-
-
Save EduardoOliveira/a3c9c1b7ba32a35e1b98979890cb97e5 to your computer and use it in GitHub Desktop.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| # generated by PrusaSlicer 2.2.0+win64 on 2020-04-18 at 14:39:21 UTC | |
| [print:A10M] | |
| avoid_crossing_perimeters = 0 | |
| bottom_fill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bottom_solid_min_thickness = 0 | |
| bridge_acceleration = 0 | |
| bridge_angle = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 0 | |
| clip_multipart_objects = 0 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| draft_shield = 0 | |
| elefant_foot_compensation = 0 | |
| ensure_vertical_shell_thickness = 0 | |
| external_perimeter_extrusion_width = 0.45 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.45 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_pattern = stars | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.42 | |
| first_layer_height = 0.35 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| gcode_label_objects = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.45 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 25% | |
| infill_speed = 80 | |
| inherits = | |
| interface_shells = 0 | |
| layer_height = 0.3 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.45 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| single_extruder_multi_material_priming = 1 | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slice_closing_radius = 0.049 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.45 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_auto = 1 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_contact_loops = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_synchronize_layers = 0 | |
| support_material_threshold = 0 | |
| support_material_with_sheath = 1 | |
| support_material_xy_spacing = 50% | |
| thin_walls = 1 | |
| threads = 8 | |
| top_fill_pattern = rectilinear | |
| top_infill_extrusion_width = 0.4 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| top_solid_min_thickness = 0 | |
| travel_speed = 130 | |
| wipe_tower = 0 | |
| wipe_tower_bridging = 10 | |
| wipe_tower_no_sparse_layers = 0 | |
| wipe_tower_rotation_angle = 0 | |
| wipe_tower_width = 60 | |
| wipe_tower_x = 180 | |
| wipe_tower_y = 140 | |
| xy_size_compensation = 0 | |
| [print:Anycubic i3 Mega DualMod] | |
| avoid_crossing_perimeters = 1 | |
| bottom_fill_pattern = rectilinear | |
| bottom_solid_layers = 4 | |
| bottom_solid_min_thickness = 0 | |
| bridge_acceleration = 800 | |
| bridge_angle = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 30 | |
| brim_width = 0 | |
| clip_multipart_objects = 1 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| complete_objects = 0 | |
| default_acceleration = 1500 | |
| dont_support_bridges = 1 | |
| draft_shield = 0 | |
| elefant_foot_compensation = 0 | |
| ensure_vertical_shell_thickness = 0 | |
| external_perimeter_extrusion_width = 0.4 | |
| external_perimeter_speed = 30 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.4 | |
| fill_angle = 45 | |
| fill_density = 25% | |
| fill_pattern = line | |
| first_layer_acceleration = 800 | |
| first_layer_extrusion_width = 0.4 | |
| first_layer_height = 0.2 | |
| first_layer_speed = 25 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| gcode_label_objects = 1 | |
| infill_acceleration = 1800 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.4 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 10% | |
| infill_speed = 60 | |
| inherits = | |
| interface_shells = 0 | |
| layer_height = 0.16 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 0 | |
| perimeter_acceleration = 800 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.4 | |
| perimeter_speed = 45 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| single_extruder_multi_material_priming = 0 | |
| skirt_distance = 5 | |
| skirt_height = 1 | |
| skirts = 3 | |
| slice_closing_radius = 0.049 | |
| small_perimeter_speed = 30 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.4 | |
| solid_infill_speed = 60 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_auto = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_contact_loops = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 2.5 | |
| support_material_speed = 45 | |
| support_material_synchronize_layers = 0 | |
| support_material_threshold = 0 | |
| support_material_with_sheath = 1 | |
| support_material_xy_spacing = 50% | |
| thin_walls = 0 | |
| threads = 8 | |
| top_fill_pattern = rectilinear | |
| top_infill_extrusion_width = 0.4 | |
| top_solid_infill_speed = 30 | |
| top_solid_layers = 4 | |
| top_solid_min_thickness = 0 | |
| travel_speed = 70 | |
| wipe_tower = 1 | |
| wipe_tower_bridging = 10 | |
| wipe_tower_no_sparse_layers = 0 | |
| wipe_tower_rotation_angle = 0 | |
| wipe_tower_width = 30 | |
| wipe_tower_x = 112.151 | |
| wipe_tower_y = 82.1353 | |
| xy_size_compensation = 0 | |
| [print:My Settings] | |
| avoid_crossing_perimeters = 0 | |
| bottom_fill_pattern = rectilinear | |
| bottom_solid_layers = 4 | |
| bottom_solid_min_thickness = 0 | |
| bridge_acceleration = 1800 | |
| bridge_angle = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 30 | |
| brim_width = 0 | |
| clip_multipart_objects = 1 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| complete_objects = 0 | |
| default_acceleration = 1800 | |
| dont_support_bridges = 1 | |
| draft_shield = 0 | |
| elefant_foot_compensation = 0 | |
| ensure_vertical_shell_thickness = 0 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 30 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.4 | |
| fill_angle = 45 | |
| fill_density = 25% | |
| fill_pattern = line | |
| first_layer_acceleration = 1800 | |
| first_layer_extrusion_width = 0 | |
| first_layer_height = 0.2 | |
| first_layer_speed = 25 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| gcode_label_objects = 1 | |
| infill_acceleration = 1800 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 5% | |
| infill_speed = 45 | |
| inherits = | |
| interface_shells = 0 | |
| layer_height = 0.2 | |
| max_print_speed = 60 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 1800 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 45 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| single_extruder_multi_material_priming = 1 | |
| skirt_distance = 5 | |
| skirt_height = 1 | |
| skirts = 3 | |
| slice_closing_radius = 0.049 | |
| small_perimeter_speed = 20 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 45 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_auto = 1 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_contact_loops = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 2.5 | |
| support_material_speed = 45 | |
| support_material_synchronize_layers = 0 | |
| support_material_threshold = 0 | |
| support_material_with_sheath = 1 | |
| support_material_xy_spacing = 50% | |
| thin_walls = 1 | |
| threads = 8 | |
| top_fill_pattern = rectilinear | |
| top_infill_extrusion_width = 0 | |
| top_solid_infill_speed = 30 | |
| top_solid_layers = 4 | |
| top_solid_min_thickness = 0 | |
| travel_speed = 70 | |
| wipe_tower = 0 | |
| wipe_tower_bridging = 10 | |
| wipe_tower_no_sparse_layers = 0 | |
| wipe_tower_rotation_angle = 0 | |
| wipe_tower_width = 60 | |
| wipe_tower_x = 180 | |
| wipe_tower_y = 140 | |
| xy_size_compensation = 0 | |
| [filament:A10M] | |
| bed_temperature = 60 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #29B2B2 | |
| filament_cooling_final_speed = 3.4 | |
| filament_cooling_initial_speed = 2.2 | |
| filament_cooling_moves = 4 | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_deretract_speed = nil | |
| filament_diameter = 1.75 | |
| filament_load_time = 0 | |
| filament_loading_speed = 28 | |
| filament_loading_speed_start = 3 | |
| filament_max_volumetric_speed = 0 | |
| filament_minimal_purge_on_wipe_tower = 15 | |
| filament_notes = "" | |
| filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" | |
| filament_retract_before_travel = nil | |
| filament_retract_before_wipe = nil | |
| filament_retract_layer_change = nil | |
| filament_retract_length = nil | |
| filament_retract_lift = nil | |
| filament_retract_lift_above = nil | |
| filament_retract_lift_below = nil | |
| filament_retract_restart_extra = nil | |
| filament_retract_speed = nil | |
| filament_settings_id = "" | |
| filament_soluble = 0 | |
| filament_toolchange_delay = 0 | |
| filament_type = PLA | |
| filament_unload_time = 0 | |
| filament_unloading_speed = 90 | |
| filament_unloading_speed_start = 100 | |
| filament_vendor = (Unknown) | |
| filament_wipe = nil | |
| first_layer_bed_temperature = 60 | |
| first_layer_temperature = 190 | |
| inherits = | |
| max_fan_speed = 100 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 190 | |
| [filament:My Settings] | |
| bed_temperature = 60 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = | |
| cooling = 1 | |
| disable_fan_first_layers = 1 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 60 | |
| filament_colour = #FF7F00 | |
| filament_cooling_final_speed = 30 | |
| filament_cooling_initial_speed = 30 | |
| filament_cooling_moves = 4 | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_deretract_speed = 45 | |
| filament_diameter = 1.75 | |
| filament_load_time = 0 | |
| filament_loading_speed = 45 | |
| filament_loading_speed_start = 3 | |
| filament_max_volumetric_speed = 0 | |
| filament_minimal_purge_on_wipe_tower = 15 | |
| filament_notes = "" | |
| filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" | |
| filament_retract_before_travel = nil | |
| filament_retract_before_wipe = nil | |
| filament_retract_layer_change = 1 | |
| filament_retract_length = nil | |
| filament_retract_lift = 0.1 | |
| filament_retract_lift_above = nil | |
| filament_retract_lift_below = nil | |
| filament_retract_restart_extra = nil | |
| filament_retract_speed = 45 | |
| filament_settings_id = "" | |
| filament_soluble = 0 | |
| filament_toolchange_delay = 0 | |
| filament_type = PLA | |
| filament_unload_time = 0 | |
| filament_unloading_speed = 90 | |
| filament_unloading_speed_start = 100 | |
| filament_vendor = (Unknown) | |
| filament_wipe = nil | |
| first_layer_bed_temperature = 60 | |
| first_layer_temperature = 190 | |
| inherits = | |
| max_fan_speed = 100 | |
| min_fan_speed = 10 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 190 | |
| [filament:PLA Orange] | |
| bed_temperature = 60 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = | |
| cooling = 0 | |
| disable_fan_first_layers = 1 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1.02 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 60 | |
| filament_colour = #808080 | |
| filament_cooling_final_speed = 3.4 | |
| filament_cooling_initial_speed = 2.2 | |
| filament_cooling_moves = 2 | |
| filament_cost = 20 | |
| filament_density = 1.24 | |
| filament_deretract_speed = nil | |
| filament_diameter = 1.75 | |
| filament_load_time = 0 | |
| filament_loading_speed = 45 | |
| filament_loading_speed_start = 25 | |
| filament_max_volumetric_speed = 0 | |
| filament_minimal_purge_on_wipe_tower = 30 | |
| filament_notes = "" | |
| filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" | |
| filament_retract_before_travel = nil | |
| filament_retract_before_wipe = nil | |
| filament_retract_layer_change = 1 | |
| filament_retract_length = nil | |
| filament_retract_lift = 0.1 | |
| filament_retract_lift_above = nil | |
| filament_retract_lift_below = nil | |
| filament_retract_restart_extra = nil | |
| filament_retract_speed = nil | |
| filament_settings_id = "" | |
| filament_soluble = 0 | |
| filament_toolchange_delay = 0 | |
| filament_type = PLA | |
| filament_unload_time = 0 | |
| filament_unloading_speed = 60 | |
| filament_unloading_speed_start = 70 | |
| filament_vendor = (Unknown) | |
| filament_wipe = nil | |
| first_layer_bed_temperature = 60 | |
| first_layer_temperature = 200 | |
| inherits = | |
| max_fan_speed = 100 | |
| min_fan_speed = 100 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 200 | |
| [filament:PLA White] | |
| bed_temperature = 60 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = | |
| cooling = 0 | |
| disable_fan_first_layers = 1 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1.03 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 60 | |
| filament_colour = #FF0080 | |
| filament_cooling_final_speed = 3.4 | |
| filament_cooling_initial_speed = 2.2 | |
| filament_cooling_moves = 3 | |
| filament_cost = 20 | |
| filament_density = 1.24 | |
| filament_deretract_speed = nil | |
| filament_diameter = 1.75 | |
| filament_load_time = 0 | |
| filament_loading_speed = 45 | |
| filament_loading_speed_start = 10 | |
| filament_max_volumetric_speed = 0 | |
| filament_minimal_purge_on_wipe_tower = 30 | |
| filament_notes = "" | |
| filament_ramming_parameters = "120 100 6.6129 6.74194 7.09677 7.58065 7.90323 8.16129 8.67742 9.3871 9.87097 10.0323| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" | |
| filament_retract_before_travel = nil | |
| filament_retract_before_wipe = nil | |
| filament_retract_layer_change = 1 | |
| filament_retract_length = nil | |
| filament_retract_lift = 0.1 | |
| filament_retract_lift_above = nil | |
| filament_retract_lift_below = nil | |
| filament_retract_restart_extra = nil | |
| filament_retract_speed = nil | |
| filament_settings_id = "" | |
| filament_soluble = 0 | |
| filament_toolchange_delay = 0 | |
| filament_type = PLA | |
| filament_unload_time = 0 | |
| filament_unloading_speed = 60 | |
| filament_unloading_speed_start = 70 | |
| filament_vendor = (Unknown) | |
| filament_wipe = nil | |
| first_layer_bed_temperature = 60 | |
| first_layer_temperature = 200 | |
| inherits = | |
| max_fan_speed = 100 | |
| min_fan_speed = 100 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 200 | |
| [printer:A10M] | |
| bed_custom_model = | |
| bed_custom_texture = | |
| bed_shape = 0x0,220x0,220x220,0x220 | |
| before_layer_gcode = | |
| between_objects_gcode = | |
| cooling_tube_length = 5 | |
| cooling_tube_retraction = 91.5 | |
| default_filament_profile = "" | |
| default_print_profile = | |
| deretract_speed = 0 | |
| end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n | |
| extra_loading_move = -2 | |
| extruder_colour = "" | |
| extruder_offset = 0x0 | |
| gcode_flavor = reprap | |
| high_current_on_filament_swap = 0 | |
| host_type = octoprint | |
| inherits = | |
| layer_gcode = | |
| machine_max_acceleration_e = 10000,5000 | |
| machine_max_acceleration_extruding = 1500,1250 | |
| machine_max_acceleration_retracting = 1500,1250 | |
| machine_max_acceleration_x = 9000,1000 | |
| machine_max_acceleration_y = 9000,1000 | |
| machine_max_acceleration_z = 500,200 | |
| machine_max_feedrate_e = 120,120 | |
| machine_max_feedrate_x = 500,200 | |
| machine_max_feedrate_y = 500,200 | |
| machine_max_feedrate_z = 12,12 | |
| machine_max_jerk_e = 2.5,2.5 | |
| machine_max_jerk_x = 10,10 | |
| machine_max_jerk_y = 10,10 | |
| machine_max_jerk_z = 0.2,0.4 | |
| machine_min_extruding_rate = 0,0 | |
| machine_min_travel_rate = 0,0 | |
| max_layer_height = 0 | |
| max_print_height = 200 | |
| min_layer_height = 0.07 | |
| nozzle_diameter = 0.4 | |
| parking_pos_retraction = 92 | |
| print_host = | |
| printer_model = | |
| printer_notes = | |
| printer_settings_id = | |
| printer_technology = FFF | |
| printer_variant = | |
| printer_vendor = | |
| printhost_apikey = | |
| printhost_cafile = | |
| remaining_times = 0 | |
| retract_before_travel = 2 | |
| retract_before_wipe = 0% | |
| retract_layer_change = 0 | |
| retract_length = 2 | |
| retract_length_toolchange = 10 | |
| retract_lift = 0 | |
| retract_lift_above = 0 | |
| retract_lift_below = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 40 | |
| serial_port = | |
| serial_speed = 250000 | |
| silent_mode = 1 | |
| single_extruder_multi_material = 0 | |
| start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n | |
| thumbnails = | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| variable_layer_height = 1 | |
| wipe = 0 | |
| z_offset = 0 | |
| [printer:My Settings] | |
| bed_custom_model = | |
| bed_custom_texture = | |
| bed_shape = 0x0,210x0,210x210,0x210 | |
| before_layer_gcode = | |
| between_objects_gcode = | |
| cooling_tube_length = 20 | |
| cooling_tube_retraction = 50 | |
| default_filament_profile = "" | |
| default_print_profile = | |
| deretract_speed = 0,0 | |
| end_gcode = M104 S0 ; turn off extruder\nM140 S0 ; turn off bed\nM84 ; disable motors\nM107\nG91 ;relative positioning\nG1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+0.5 E-5 ;X-20 Y-20 F[travel_speed] ;move Z up a bit and retract filament even more\nG28 X0 ;Y0 ;move X/Y to min endstops, so the head is out of the way\nG1 Y180 F2000\nM84 ;steppers off\nG90\nM300 P300 S4000 | |
| extra_loading_move = -2 | |
| extruder_colour = ; | |
| extruder_offset = 0x0,0x0 | |
| gcode_flavor = marlin | |
| high_current_on_filament_swap = 0 | |
| host_type = octoprint | |
| inherits = | |
| layer_gcode = | |
| machine_max_acceleration_e = 800,5000 | |
| machine_max_acceleration_extruding = 1000,1250 | |
| machine_max_acceleration_retracting = 1000,1250 | |
| machine_max_acceleration_x = 1800,1000 | |
| machine_max_acceleration_y = 1800,1000 | |
| machine_max_acceleration_z = 400,200 | |
| machine_max_feedrate_e = 100,100 | |
| machine_max_feedrate_x = 100,100 | |
| machine_max_feedrate_y = 100,100 | |
| machine_max_feedrate_z = 12,12 | |
| machine_max_jerk_e = 1,2.5 | |
| machine_max_jerk_x = 8,8 | |
| machine_max_jerk_y = 8,8 | |
| machine_max_jerk_z = 0.2,0.4 | |
| machine_min_extruding_rate = 0,0 | |
| machine_min_travel_rate = 0,0 | |
| max_layer_height = 0.3,0.3 | |
| max_print_height = 205 | |
| min_layer_height = 0.06,0.06 | |
| nozzle_diameter = 0.4,0.4 | |
| parking_pos_retraction = 75 | |
| print_host = | |
| printer_model = | |
| printer_notes = | |
| printer_settings_id = | |
| printer_technology = FFF | |
| printer_variant = | |
| printer_vendor = | |
| printhost_apikey = | |
| printhost_cafile = | |
| remaining_times = 0 | |
| retract_before_travel = 1.1,1.1 | |
| retract_before_wipe = 0%,0% | |
| retract_layer_change = 1,1 | |
| retract_length = 6.5,6.5 | |
| retract_length_toolchange = 10,10 | |
| retract_lift = 0.1,0.1 | |
| retract_lift_above = 0,0 | |
| retract_lift_below = 0,0 | |
| retract_restart_extra = 0,0 | |
| retract_restart_extra_toolchange = 0,0 | |
| retract_speed = 45,45 | |
| serial_port = | |
| serial_speed = 250000 | |
| silent_mode = 0 | |
| single_extruder_multi_material = 1 | |
| start_gcode = G21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nG28 X0 Y0 ;move X/Y to min endstops\nG28 Z0 ;move Z to min endstops\nG1 Z15.0 F[travel_speed] ;move the platform down 15mm\nG92 E0 ;zero the extruded length\nG1 F200 E3 ;extrude 3mm of feed stock\nG92 E0 ;zero the extruded length again\nG1 F[travel_speed]\nG0 Y20 F[travel_speed]\nG5\n\n;;END OF START GCODE | |
| thumbnails = | |
| toolchange_gcode = T{next_extruder}\nM400\nM42 P11 S{next_extruder*255} | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 1 | |
| use_volumetric_e = 0 | |
| variable_layer_height = 0 | |
| wipe = 0,0 | |
| z_offset = 0 | |
| [presets] | |
| print = Anycubic i3 Mega DualMod | |
| sla_print = | |
| sla_material = | |
| printer = My Settings | |
| filament = PLA Orange | |
| filament_1 = PLA White |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment