Skip to content

Instantly share code, notes, and snippets.

@EverythingSmartHome
Last active September 30, 2024 10:41
Show Gist options
  • Save EverythingSmartHome/055fbdde31a607ef9d695d5cac780e94 to your computer and use it in GitHub Desktop.
Save EverythingSmartHome/055fbdde31a607ef9d695d5cac780e94 to your computer and use it in GitHub Desktop.
ESP32 & ESPHome Voice Assistant
esphome:
name: esp32-mic-speaker
friendly_name: esp32-mic-speaker
on_boot:
- priority: -100
then:
- wait_until: api.connected
- delay: 1s
- if:
condition:
switch.is_on: use_wake_word
then:
- voice_assistant.start_continuous:
esp32:
board: esp32dev
framework:
type: esp-idf
version: recommended
# Enable logging
logger:
# Enable Home Assistant API
api:
ota:
wifi:
ssid: !secret wifi_ssid
password: !secret wifi_password
# Enable fallback hotspot (captive portal) in case wifi connection fails
ap:
ssid: "Esp32-Mic-Speaker"
password: "9vYvAFzzPjuc"
i2s_audio:
i2s_lrclk_pin: GPIO27
i2s_bclk_pin: GPIO26
microphone:
- platform: i2s_audio
id: mic
adc_type: external
i2s_din_pin: GPIO13
pdm: false
speaker:
- platform: i2s_audio
id: big_speaker
dac_type: external
i2s_dout_pin: GPIO25
mode: mono
voice_assistant:
microphone: mic
use_wake_word: false
noise_suppression_level: 2
auto_gain: 31dBFS
volume_multiplier: 2.0
speaker: big_speaker
id: assist
switch:
- platform: template
name: Use wake word
id: use_wake_word
optimistic: true
restore_mode: RESTORE_DEFAULT_ON
entity_category: config
on_turn_on:
- lambda: id(assist).set_use_wake_word(true);
- if:
condition:
not:
- voice_assistant.is_running
then:
- voice_assistant.start_continuous
on_turn_off:
- voice_assistant.stop
- lambda: id(assist).set_use_wake_word(false);
@strusic
Copy link

strusic commented May 17, 2024

I successfully flashed this yaml, but there are a lot of cracklings and distortion while playing anything on speaker. I am using max98357a as amp and MEMS I2S - DFRobot SEN0526

@indevor
Copy link

indevor commented May 17, 2024

l_r: "right" # INMP441 - L/R (GND = right / 3.3v = left)
di: "GPIO9" # WS2812 - DI

Funny, you're wrong again. Maybe you're copying from the wrong source.
According to the document for this microphone:

Left/Right Channel Select. When set low, the microphone outputs its signal in the left channel
of the I²S frame. When set high, the microphone outputs its signal in the right channel.
GND = LEFT

@indevor
Copy link

indevor commented May 17, 2024

Hey strusic, I was having some of those same issues with the microphone until I enabled micro_wake_word. Below is my current testing yaml for a XIAO ESP32-S3 using duplex mode on a shared i2s_audio channel in order to cut down on the number of pins needed. This is working very well especially in conjunction with Extended OpenAI Conversation. I have ChatGPT 4.o configured to "embody" HAL 9000 and it has been very entertaining. Printing a HAL 9000 prop replica to hold the assistant hardware.

edit: removed OTA password.... edit2: fixed persistent "connecting" led effect after boot

substitutions:
  device_name: "test-media-assistant-v2"
  friendly_name: "Test Media Assistant V2"
  device_description: "XIAO ESP32 S3"
  esp_board: "esp32-s3-devkitc-1"
  framework_type: "esp-idf"
  din: "GPIO1"   # MAX98357A - DIN
  lrclk: "GPIO7" # MAX98357A - LRCLK / INMP441 - WS
  bclk: "GPIO8"  # MAX98357A - BCLK / INMP441 - SCK
  sd: "GPIO2"    # INMP441 - SD
  l_r: "right"   # INMP441 - L/R (GND = right / 3.3v = left)
  di: "GPIO9"   # WS2812 - DI
  api_key: "xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx"
  # Phases of the Voice Assistant
  # IDLE: The voice assistant is ready to be triggered by a wake-word
  voice_assist_idle_phase_id: '1'
  # LISTENING: The voice assistant is ready to listen to a voice command (after being triggered by the wake word)
  voice_assist_listening_phase_id: '2'
  # THINKING: The voice assistant is currently processing the command
  voice_assist_thinking_phase_id: '3'
  # REPLYING: The voice assistant is replying to the command
  voice_assist_replying_phase_id: '4'
  # NOT_READY: The voice assistant is not ready
  voice_assist_not_ready_phase_id: '10'
  # ERROR: The voice assistant encountered an error
  voice_assist_error_phase_id: '11'
  # MUTED: The voice assistant is muted and will not reply to a wake-word
  voice_assist_muted_phase_id: '12'

external_components:
  - source:
      type: git
      url: https://github.com/gnumpi/esphome_audio
      ref: main
      #type: local
      #path: /Users/siekmann/Privat/Projects/espHome/esphome_audio/esphome/components
    components: [ adf_pipeline, i2s_audio ]

esphome:
  name: ${device_name}
  comment: ${device_description}
  friendly_name: ${friendly_name}
  min_version: 2024.2.0
  platformio_options:
    build_flags: -DBOARD_HAS_PSRAM
    board_build.flash_mode: dio
    board_upload.maximum_size: 16777216
  on_boot:
    priority: 600
    then:
      # Run the script to refresh the LED status
      # If after 30 seconds, the device is still initializing (It did not yet connect to Home Assistant), turn off the init_in_progress variable and run the script to refresh the LED status
      - delay: 30s
      - if:
          condition:
            lambda: return id(init_in_progress);
          then:
            - lambda: id(init_in_progress) = false;
                            
esp32:
  board: ${esp_board}
  variant: ESP32S3
  flash_size: 16MB
  framework:
    type: ${framework_type}
    version: recommended
    sdkconfig_options:
      # need to set a s3 compatible board for the adf-sdk to compile
      # board specific code is not used though
      CONFIG_ESP32_S3_BOX_BOARD: "y"
      CONFIG_ESP32_WIFI_STATIC_RX_BUFFER_NUM: "16"
      CONFIG_ESP32_WIFI_DYNAMIC_RX_BUFFER_NUM: "512"
      CONFIG_TCPIP_RECVMBOX_SIZE: "512"

      CONFIG_TCP_SND_BUF_DEFAULT: "65535"
      CONFIG_TCP_WND_DEFAULT: "512000"
      CONFIG_TCP_RECVMBOX_SIZE: "512"

logger:

globals:
  # Global initialisation variable. Initialized to true and set to false once everything is connected. Only used to have a smooth "plugging" experience
  - id: init_in_progress
    type: bool
    restore_value: no
    initial_value: 'true'
  # Global variable tracking the phase of the voice assistant (defined above). Initialized to not_ready
  - id: voice_assistant_phase
    type: int
    restore_value: no
    initial_value: ${voice_assist_not_ready_phase_id}

psram:
  mode: octal
  speed: 80MHz

wifi:
  enable_rrm: true
  ssid: !secret wifi_ssid
  password: !secret wifi_password
  fast_connect: true

ota:
  password: !secret ota_password

api:
  encryption:
    key: ${api_key}

i2s_audio:
  - id: i2s_dplx
    i2s_lrclk_pin: ${lrclk}
    i2s_bclk_pin: ${bclk}
    access_mode: duplex

adf_pipeline:
  - platform: i2s_audio
    type: audio_out
    id: adf_i2s_out
    i2s_audio_id: i2s_dplx
    i2s_dout_pin: ${din}
    sample_rate: 16000
    bits_per_sample: 32bit
    fixed_settings: true

  - platform: i2s_audio
    type: audio_in
    id: adf_i2s_in
    i2s_audio_id: i2s_dplx
    i2s_din_pin: ${sd}
    pdm: false
    channel: ${l_r}
    sample_rate: 16000
    bits_per_sample: 32bit
    fixed_settings: true

microphone:
  - platform: adf_pipeline
    id: adf_microphone
    keep_pipeline_alive: true
    pipeline:
      - adf_i2s_in
      - self
      
media_player:
  - platform: adf_pipeline
    id: adf_media_player
    name: media_player
    keep_pipeline_alive: true
    internal: false
    pipeline:
      - self
      - resampler
      - adf_i2s_out

micro_wake_word:
  model: okay_nabu
  on_wake_word_detected:
      - media_player.stop:
      - light.turn_on:
          id: led_ring
          blue: 0%
          red: 0%
          green: 100%
          brightness: 75%
          effect: pulse
      - voice_assistant.start:

voice_assistant:
  microphone: adf_microphone
  media_player: adf_media_player

  use_wake_word: false
  #vad_threshold: 3

  noise_suppression_level: 1
  auto_gain: 31dBFS
  volume_multiplier: 15.0

  on_client_connected:
    - lambda: id(init_in_progress) = false;
    - if:
        condition:
          switch.is_on: use_wake_word
        then:
          - micro_wake_word.start:
          - lambda: id(voice_assistant_phase) = ${voice_assist_idle_phase_id};
          - script.execute: reset_led
        else:
          - lambda: id(voice_assistant_phase) = ${voice_assist_muted_phase_id};

  on_client_disconnected:
    - lambda: id(voice_assistant_phase) = ${voice_assist_not_ready_phase_id};
    - voice_assistant.stop
    - micro_wake_word.stop
    - light.turn_on:
          id: led_ring
          blue: 0%
          red: 100%
          green: 100%
          brightness: 50%
          effect: connecting

  on_listening:
    - light.turn_on:
        id: led_ring
        blue: 100%
        red: 0%
        green: 0%
        brightness: 25%
        effect: wakeword
        
  on_tts_start:
    - light.turn_on:
        id: led_ring
        blue: 0%
        red: 0%
        green: 100%
        brightness: 75%
        effect: pulse
  
  on_end:
      then:
        - light.turn_off:
            id: led_ring
        - voice_assistant.stop
        - wait_until:
            not:
              media_player.is_playing:
        - script.execute: reset_led
        - if:
            condition:
              switch.is_on: use_wake_word
            then:
              - micro_wake_word.start:
  on_error:
    - light.turn_on:
        id: led_ring
        blue: 0%
        red: 100%
        green: 0%
        brightness: 100%
        effect: none
    - delay: 1s
    - script.execute: reset_led
    - script.wait: reset_led
    - lambda: |-
        if (code == "wake-provider-missing" || code == "wake-engine-missing") {
          id(use_wake_word).turn_off();
        }
    - if:
        condition:
          switch.is_on: use_wake_word
        then:
          - micro_wake_word.start:
          - script.execute: reset_led
              
script:
  - id: reset_led
    then:
      - if:
          condition:
            switch.is_on: use_wake_word
          then:
            - light.turn_on:
                id: led_ring
                blue: 100%
                red: 0%
                green: 0%
                brightness: 25%
                effect: none
          else:
            - light.turn_off: led_ring
 
button:
  - platform: restart
    id: restart_btn
    name: "${friendly_name} REBOOT"
            
switch:
  - platform: template
    name: Enable Voice Assistant
    id: use_wake_word
    optimistic: true
    restore_mode: RESTORE_DEFAULT_ON
    icon: mdi:assistant
    # When the switch is turned on (on Home Assistant):
    # Start the voice assistant component
    # Set the correct phase and run the script to refresh the LED status
    on_turn_on:
      - logger.log: "switch on"
      - if:
          condition:
            lambda: return !id(init_in_progress);
          then:
            - logger.log: "condition 1"
            - lambda: id(voice_assistant_phase) = ${voice_assist_idle_phase_id};
            - voice_assistant.stop
            - delay: 1s
            - if:
                condition:
                  not:
                    - voice_assistant.is_running
                then:
                  - logger.log: "Starting MWW"
                  #- voice_assistant.start_continuous
                  - micro_wake_word.start:
      - script.execute: reset_led
    on_turn_off:
      - if:
          condition:
            lambda: return !id(init_in_progress);
          then:
            - voice_assistant.stop
            - micro_wake_word.stop
            - lambda: id(voice_assistant_phase) = ${voice_assist_muted_phase_id};
      - script.execute: reset_led

  - platform: template
    name: Pipeline
    id: pipeline_switch
    optimistic: true
    restore_mode: RESTORE_DEFAULT_OFF

    on_turn_off:
      - media_player.stop

    on_turn_on:
      - media_player.play_media: "https://dl.espressif.com/dl/audio/ff-16b-2c-44100hz.mp3"

light:
  - platform: esp32_rmt_led_strip
    id: led_ring
    name: "${friendly_name} Light"
    pin: ${di}
    num_leds: 16
    rmt_channel: 0
    rgb_order: GRB
    chipset: ws2812
    default_transition_length: 0s
    effects:
      - pulse:
          name: "Pulse"
          transition_length: 0.5s
          update_interval: 0.5s
      - addressable_twinkle:
          name: "Working"
          twinkle_probability: 5%
          progress_interval: 4ms
      - addressable_color_wipe:
          name: "Wakeword"
          colors:
            - red: 0%
              green: 50%
              blue: 0%
              num_leds: 12
          add_led_interval: 20ms
          reverse: false
      - addressable_color_wipe:
          name: "Connecting"
          colors:
            - red: 60%
              green: 60%
              blue: 60%
              num_leds: 12
            - red: 60%
              green: 60%
              blue: 0%
              num_leds: 12
          add_led_interval: 100ms
          reverse: true
INFO ESPHome 2024.5.0
INFO Reading configuration /config/esphome/test.yaml...
WARNING GPIO3 is a strapping PIN and should only be used for I/O with care.
Attaching external pullup/down resistors to strapping pins can cause unexpected failures.
See https://esphome.io/guides/faq.html#why-am-i-getting-a-warning-about-strapping-pins
WARNING GPIO45 is a strapping PIN and should only be used for I/O with care.
Attaching external pullup/down resistors to strapping pins can cause unexpected failures.
See https://esphome.io/guides/faq.html#why-am-i-getting-a-warning-about-strapping-pins
INFO Generating C++ source...
INFO Updating https://github.com/espressif/esp-adf.git@v2.5
INFO Updating submodules (components/esp-adf-libs, components/esp-sr) for https://github.com/espressif/esp-adf.git@v2.5
Traceback (most recent call last):
  File "/usr/local/bin/esphome", line 33, in <module>
    sys.exit(load_entry_point('esphome', 'console_scripts', 'esphome')())
             ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
  File "/esphome/esphome/__main__.py", line 1065, in main
    return run_esphome(sys.argv)
           ^^^^^^^^^^^^^^^^^^^^^
  File "/esphome/esphome/__main__.py", line 1052, in run_esphome
    rc = POST_CONFIG_ACTIONS[args.command](args, config)
         ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
  File "/esphome/esphome/__main__.py", line 479, in command_run
    exit_code = write_cpp(config)
                ^^^^^^^^^^^^^^^^^
  File "/esphome/esphome/__main__.py", line 193, in write_cpp
    return write_cpp_file()
           ^^^^^^^^^^^^^^^^
  File "/esphome/esphome/__main__.py", line 211, in write_cpp_file
    writer.write_cpp(code_s)
  File "/esphome/esphome/writer.py", line 344, in write_cpp
    copy_src_tree()
  File "/esphome/esphome/writer.py", line 297, in copy_src_tree
    copy_files()
  File "/esphome/esphome/components/esp32/__init__.py", line 684, in copy_files
    repo_dir, _ = git.clone_or_update(
                  ^^^^^^^^^^^^^^^^^^^^
  File "/esphome/esphome/git.py", line 111, in clone_or_update
    run_git_command(
  File "/esphome/esphome/git.py", line 31, in run_git_command
    raise cv.Invalid(lines[-1][len("fatal: ") :])
voluptuous.error.Invalid: Unable to find current revision in submodule path 'components/esp-adf-libs'

@imonlinux
Copy link

imonlinux commented May 17, 2024

Hey indevor,

I have so many versions of this config running on different esp32 boards now I must have pulled that old config back in at some point. The odd thing is that this specific config running on the XIAO ESP32-S3 with a INMP441 with grounded L/R pin set to Right channel is working perfectly. When I'm back home I will change it back to Left and see if it continues to work. I was 100% wrong. I have the INMP441 L/R channel set high. That is why the selection of right channel is working but my note in substitutions is backwards again. Thanks again indevor!

Not sure what your last post was indicating, I have moved away from using GPIO3 and GPIO45 due to these warnings and am now using the single i2s_audio channel in duplex mode. Not sure where that voluptuous.error is coming from on your run. I just reran this config after doing a Clean Build Files and it compiles as expected.

edit: typo
edit2: added completion of build
edit3: confirmed that INMP441 L/R channel is set high and not low so right channel is working and fixed in config above

INFO ESPHome 2024.5.0
INFO Reading configuration /config/esphome/test-media-assistant-v2.yaml...
INFO Generating C++ source...
INFO Updating https://github.com/espressif/esp-adf.git@v2.5
INFO Updating submodules (components/esp-adf-libs, components/esp-sr) for https://github.com/espressif/esp-adf.git@v2.5
INFO Updating https://github.com/espressif/esp-tflite-micro@None
INFO Compiling app...
Processing test-media-assistant-v2 (board: esp32-s3-devkitc-1; framework: espidf; platform: platformio/espressif32@5.4.0)
--------------------------------------------------------------------------------
Library Manager: Installing esphome/noise-c @ 0.1.4
INFO Installing esphome/noise-c @ 0.1.4
Unpacking  [####################################]  100%
Library Manager: noise-c@0.1.4 has been installed!
INFO noise-c@0.1.4 has been installed!
Library Manager: Resolving dependencies...
INFO Resolving dependencies...
Library Manager: Installing esphome/libsodium @ 1.10018.1
INFO Installing esphome/libsodium @ 1.10018.1
Unpacking  [####################################]  100%
Library Manager: libsodium@1.10018.1 has been installed!
INFO libsodium@1.10018.1 has been installed!
HARDWARE: ESP32S3 240MHz, 320KB RAM, 16MB Flash
 - framework-espidf @ 3.40407.0 (4.4.7) 
 - tool-cmake @ 3.16.4 
 - tool-ninja @ 1.7.1 
 - toolchain-esp32ulp @ 2.35.0-20220830 
 - toolchain-riscv32-esp @ 8.4.0+2021r2-patch5 
 - toolchain-xtensa-esp32s3 @ 8.4.0+2021r2-patch5
Reading CMake configuration...
Generating assembly for certificate bundle...
Dependency Graph
|-- noise-c @ 0.1.4
Generating assembly for .pioenvs/test-media-assistant-v2/duer_profile.S
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/adf_pipeline/adf_audio_element.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/adf_pipeline/adf_audio_process.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/adf_pipeline/adf_audio_sinks.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/adf_pipeline/adf_audio_sources.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/adf_pipeline/adf_pipeline.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/adf_pipeline/adf_pipeline_controller.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/adf_pipeline/media_player/adf_media_player.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/adf_pipeline/microphone/esp_adf_microphone.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/api/api_connection.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/api/api_frame_helper.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/api/api_pb2.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/api/api_pb2_service.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/api/api_server.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/api/list_entities.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/api/proto.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/api/subscribe_state.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/api/user_services.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/button/button.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/esp32/core.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/esp32/gpio.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/esp32/preferences.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/esp32_rmt_led_strip/led_strip.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/i2s_audio/adf_pipeline/adf_i2s_in.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/i2s_audio/adf_pipeline/adf_i2s_out.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/i2s_audio/adf_pipeline/i2s_stream_mod.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/i2s_audio/external_adc.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/i2s_audio/external_dac.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/i2s_audio/i2s_audio.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/light/addressable_light.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/light/automation.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/light/esp_color_correction.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/light/esp_hsv_color.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/light/esp_range_view.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/light/light_call.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/light/light_json_schema.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/light/light_output.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/light/light_state.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/logger/logger.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/logger/logger_esp32.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/logger/logger_esp8266.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/logger/logger_host.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/logger/logger_libretiny.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/logger/logger_rp2040.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/md5/md5.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/mdns/mdns_component.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/mdns/mdns_esp32.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/mdns/mdns_esp8266.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/mdns/mdns_host.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/mdns/mdns_libretiny.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/mdns/mdns_rp2040.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/media_player/media_player.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/micro_wake_word/micro_wake_word.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/network/util.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/ota/ota_backend_arduino_esp32.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/ota/ota_backend_arduino_esp8266.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/ota/ota_backend_arduino_libretiny.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/ota/ota_backend_arduino_rp2040.o
Compiling .pioenvs/test-media-assistant-v2/src/esphome/components/ota/ota_backend_esp_idf.o
.
.
.
.
Linking .pioenvs/test-media-assistant-v2/firmware.elf
/data/cache/platformio/packages/toolchain-xtensa-esp32s3/bin/../lib/gcc/xtensa-esp32s3-elf/8.4.0/../../../../xtensa-esp32s3-elf/bin/ld: missing --end-group; added as last command line option
RAM:   [=         ]  12.0% (used 39348 bytes from 327680 bytes)
Flash: [==        ]  17.8% (used 1444629 bytes from 8126464 bytes)
Building .pioenvs/test-media-assistant-v2/firmware.bin
Creating esp32s3 image...
Successfully created esp32s3 image.
esp32_create_combined_bin([".pioenvs/test-media-assistant-v2/firmware.bin"], [".pioenvs/test-media-assistant-v2/firmware.elf"])
Wrote 0x170c80 bytes to file /data/build/test-media-assistant-v2/.pioenvs/test-media-assistant-v2/firmware-factory.bin, ready to flash to offset 0x0
======================== [SUCCESS] Took 1629.69 seconds ========================
INFO Successfully compiled program.

@imonlinux
Copy link

imonlinux commented May 17, 2024

Hey strusic,

I haven't used that mic board before, but I am using the same output amp. What kind of speaker are you using? I have tried a few and am having a lot of success with this one running at 50% volume:

https://www.amazon.com/dp/B01CHYIU26

When I get home, I will record a video of it working as a reference and link it here.

edit: included volume level

@strusic
Copy link

strusic commented May 17, 2024

I am using speaker from old bt speaker. It sounds good when I was using only i2s mediaplayer with esp32-s2 mini. I have plan to get all electronics into case of that speaker.

@imonlinux
Copy link

You may want to take a look at gnumpi's config for Shared I2S-Port with Exclusive Access instead of duplex mode.

https://github.com/gnumpi/esphome_audio

@strusic
Copy link

strusic commented May 18, 2024

I kinda managed to get it work but it sound like from hell

20240518_135917.mp4

@imonlinux
Copy link

Wow. That's ruff. If you changed to exclusive mode, did you include resampler in the pipeline for the media_player?

media_player:
  - platform: adf_pipeline
    id: adf_media_player
    name: s3-dev_media_player
    internal: false
    keep_pipeline_alive: true
    pipeline:
      - self
      - resampler
      - adf_i2s_out

This is mine in duplex mode.

20240518_092752.1.mp4

@HA-TB303
Copy link

HA-TB303 commented May 30, 2024

Hey, based on the config above I have been cooking this:

substitutions:
  device_name: "test-01"
  friendly_name: "test-01"
  device_description: "esp32s3"
  esp_board: "esp32-s3-devkitc-1"
  # Phases of the Voice Assistant
  # IDLE: The voice assistant is ready to be triggered by a wake-word
  voice_assist_idle_phase_id: '1'
  # LISTENING: The voice assistant is ready to listen to a voice command (after being triggered by the wake word)
  voice_assist_listening_phase_id: '2'
  # THINKING: The voice assistant is currently processing the command
  voice_assist_thinking_phase_id: '3'
  # REPLYING: The voice assistant is replying to the command
  voice_assist_replying_phase_id: '4'
  # NOT_READY: The voice assistant is not ready
  voice_assist_not_ready_phase_id: '10'
  # ERROR: The voice assistant encountered an error
  voice_assist_error_phase_id: '11'
  # MUTED: The voice assistant is muted and will not reply to a wake-word
  voice_assist_muted_phase_id: '12'

external_components:
  - source:
      type: git
      url: https://github.com/gnumpi/esphome_audio
      ref: main
      #type: local
      #path: /Users/siekmann/Privat/Projects/espHome/esphome_audio/esphome/components
    components: [ adf_pipeline, i2s_audio ]

esphome:
  name: ${device_name}
  comment: ${device_description}
  friendly_name: ${friendly_name}
  min_version: 2024.2.0
  platformio_options:
    build_flags: -DBOARD_HAS_PSRAM
    board_build.flash_mode: dio
    board_upload.maximum_size: 16777216
  on_boot:
    priority: 600
    then:
      # Run the script to refresh the LED status
      # If after 30 seconds, the device is still initializing (It did not yet connect to Home Assistant), turn off the init_in_progress variable and run the script to refresh the LED status
      - delay: 30s
      - if:
          condition:
            lambda: return id(init_in_progress);
          then:
            - lambda: id(init_in_progress) = false;
                            
esp32:
  board: ${esp_board}
  variant: ESP32S3
  flash_size: 16MB
  framework:
    type: esp-idf
    sdkconfig_options:
      # need to set a s3 compatible board for the adf-sdk to compile
      # board specific code is not used though
      CONFIG_ESP32_S3_BOX_BOARD: "y"
      CONFIG_ESP32_WIFI_STATIC_RX_BUFFER_NUM: "16"
      CONFIG_ESP32_WIFI_DYNAMIC_RX_BUFFER_NUM: "512"
      CONFIG_TCPIP_RECVMBOX_SIZE: "512"

      CONFIG_TCP_SND_BUF_DEFAULT: "65535"
      CONFIG_TCP_WND_DEFAULT: "512000"
      CONFIG_TCP_RECVMBOX_SIZE: "512"

logger:

globals:
  # Global initialisation variable. Initialized to true and set to false once everything is connected. Only used to have a smooth "plugging" experience
  - id: init_in_progress
    type: bool
    restore_value: no
    initial_value: 'true'
  # Global variable tracking the phase of the voice assistant (defined above). Initialized to not_ready
  - id: voice_assistant_phase
    type: int
    restore_value: no
    initial_value: ${voice_assist_not_ready_phase_id}

psram:
  mode: octal
  speed: 80MHz

wifi:
  enable_rrm: true
  ssid: !secret wifi_ssid
  password: !secret wifi_password
  fast_connect: true

ota:
  password: !secret ota_password

api:
  encryption:
    key: !secret api_key

i2s_audio:
  - id: i2s_in
    i2s_lrclk_pin: GPIO7
    i2s_bclk_pin: GPIO16
  - id: i2s_out
    i2s_lrclk_pin: GPIO8
    i2s_bclk_pin: GPIO18

adf_pipeline:
  - platform: i2s_audio
    type: audio_out
    id: adf_i2s_out
    i2s_audio_id: i2s_out
    i2s_dout_pin: GPIO17

  - platform: i2s_audio
    type: audio_in
    id: adf_i2s_in
    i2s_audio_id: i2s_in
    i2s_din_pin: GPIO15
    pdm: false
    channel: right
    sample_rate: 16000
    bits_per_sample: 32bit

microphone:
  - platform: adf_pipeline
    id: adf_microphone
    keep_pipeline_alive: true
    pipeline:
      - adf_i2s_in
      - self
      
media_player:
  - platform: adf_pipeline
    id: adf_media_player
    name: media_player
    keep_pipeline_alive: true
    internal: false
    pipeline:
      - self
      - resampler
      - adf_i2s_out

micro_wake_word:
  model: okay_nabu
  on_wake_word_detected:
      - media_player.stop:
      - light.turn_on:
          id: led_ring
          blue: 0%
          red: 0%
          green: 100%
          brightness: 75%
          effect: pulse
      - voice_assistant.start:

voice_assistant:
  microphone: adf_microphone
  media_player: adf_media_player
  use_wake_word: false
  #vad_threshold: 3
  #noise_suppression_level: 1
  auto_gain: 31dBFS
  #volume_multiplier: 15.0

  on_client_connected:
    - lambda: id(init_in_progress) = false;
    - if:
        condition:
          switch.is_on: use_wake_word
        then:
          - micro_wake_word.start:
          - lambda: id(voice_assistant_phase) = ${voice_assist_idle_phase_id};
          - script.execute: reset_led
        else:
          - lambda: id(voice_assistant_phase) = ${voice_assist_muted_phase_id};

  on_client_disconnected:
    - lambda: id(voice_assistant_phase) = ${voice_assist_not_ready_phase_id};
    - voice_assistant.stop
    - micro_wake_word.stop
    - light.turn_on:
          id: led_ring
          blue: 0%
          red: 100%
          green: 100%
          brightness: 50%
          effect: connecting

  on_listening:
    - light.turn_on:
        id: led_ring
        blue: 100%
        red: 0%
        green: 0%
        brightness: 25%
        effect: wakeword
        
  on_tts_start:
    - light.turn_on:
        id: led_ring
        blue: 0%
        red: 0%
        green: 100%
        brightness: 75%
        effect: pulse
  
  on_end:
      then:
        - light.turn_off:
            id: led_ring
        - voice_assistant.stop
        - wait_until:
            not:
              media_player.is_playing:
        - script.execute: reset_led
        - if:
            condition:
              switch.is_on: use_wake_word
            then:
              - micro_wake_word.start:
  on_error:
    - light.turn_on:
        id: led_ring
        blue: 0%
        red: 100%
        green: 0%
        brightness: 100%
        effect: none
    - delay: 1s
    - script.execute: reset_led
    - script.wait: reset_led
    - lambda: |-
        if (code == "wake-provider-missing" || code == "wake-engine-missing") {
          id(use_wake_word).turn_off();
        }
    - if:
        condition:
          switch.is_on: use_wake_word
        then:
          - micro_wake_word.start:
          - script.execute: reset_led
              
script:
  - id: reset_led
    then:
      - if:
          condition:
            switch.is_on: use_wake_word
          then:
            - light.turn_on:
                id: led_ring
                blue: 100%
                red: 0%
                green: 0%
                brightness: 25%
                effect: none
          else:
            - light.turn_off: led_ring
 
button:
  - platform: restart
    id: restart_btn
    name: "${friendly_name} REBOOT"
            
switch:
  - platform: template
    name: Enable Voice Assistant
    id: use_wake_word
    optimistic: true
    restore_mode: RESTORE_DEFAULT_ON
    icon: mdi:assistant
    # When the switch is turned on (on Home Assistant):
    # Start the voice assistant component
    # Set the correct phase and run the script to refresh the LED status
    on_turn_on:
      - logger.log: "switch on"
      - if:
          condition:
            lambda: return !id(init_in_progress);
          then:
            - logger.log: "condition 1"
            - lambda: id(voice_assistant_phase) = ${voice_assist_idle_phase_id};
            - voice_assistant.stop
            - delay: 1s
            - if:
                condition:
                  not:
                    - voice_assistant.is_running
                then:
                  - logger.log: "Starting MWW"
                  #- voice_assistant.start_continuous
                  - micro_wake_word.start:
      - script.execute: reset_led
    on_turn_off:
      - if:
          condition:
            lambda: return !id(init_in_progress);
          then:
            - voice_assistant.stop
            - micro_wake_word.stop
            - lambda: id(voice_assistant_phase) = ${voice_assist_muted_phase_id};
      - script.execute: reset_led

  - platform: template
    name: Pipeline
    id: pipeline_switch
    optimistic: true
    restore_mode: RESTORE_DEFAULT_OFF

    on_turn_off:
      - media_player.stop

light:
  - platform: esp32_rmt_led_strip
    id: led_ring
    name: "${friendly_name} Front LED"
    pin: GPIO05
    num_leds: 1
    rmt_channel: 1
    rgb_order: GRB
    chipset: ws2812
    default_transition_length: 0s
    effects:
      - pulse:
          name: "Pulse"
          transition_length: 0.5s
          update_interval: 0.5s
      - addressable_twinkle:
          name: "Working"
          twinkle_probability: 5%
          progress_interval: 4ms
      - addressable_color_wipe:
          name: "Wakeword"
          colors:
            - red: 0%
              green: 50%
              blue: 0%
              num_leds: 12
          add_led_interval: 20ms
          reverse: false
      - addressable_color_wipe:
          name: "Connecting"
          colors:
            - red: 60%
              green: 60%
              blue: 60%
              num_leds: 1
            - red: 60%
              green: 60%
              blue: 0%
              num_leds: 1
          add_led_interval: 100ms
          reverse: true

This works extremely well, but just once ;)

The second time, it detects the wake word, starts blinking green, does not process the request and keeps blinking.

LOG (after trying twice)

INFO ESPHome 2024.5.4
[21:08:48][I][app:100]: ESPHome version 2024.5.4 compiled on May 30 2024, 21:05:15
[21:08:48][C][wifi:580]: WiFi:
[21:08:48][C][wifi:408]:   Local MAC: 3C:84:27:CC:42:0C
[21:08:48][C][wifi:413]:   SSID: [redacted]
[21:08:48][C][wifi:416]:   IP Address: 192.168.207.246
[21:08:48][C][wifi:420]:   BSSID: [redacted]
[21:08:48][C][wifi:421]:   Hostname: 'test-01'
[21:08:48][C][wifi:423]:   Signal strength: -60 dB ▂▄▆█
[21:08:48][C][wifi:427]:   Channel: 11
[21:08:48][C][wifi:428]:   Subnet: 255.255.255.0
[21:08:48][C][wifi:429]:   Gateway: 192.168.207.1
[21:08:48][C][wifi:430]:   DNS1: 192.168.207.130
[21:08:48][C][wifi:431]:   DNS2: 0.0.0.0
[21:08:48][C][wifi:433]:   BTM: disabled
[21:08:48][C][wifi:434]:   RRM: enabled
[21:08:48][C][logger:185]: Logger:
[21:08:48][C][logger:186]:   Level: DEBUG
[21:08:48][C][logger:188]:   Log Baud Rate: 115200
[21:08:48][C][logger:189]:   Hardware UART: USB_SERIAL_JTAG
[21:08:48][C][esp32_rmt_led_strip:175]: ESP32 RMT LED Strip:
[21:08:48][C][esp32_rmt_led_strip:176]:   Pin: 5
[21:08:48][C][esp32_rmt_led_strip:177]:   Channel: 1
[21:08:48][C][esp32_rmt_led_strip:202]:   RGB Order: GRB
[21:08:48][C][esp32_rmt_led_strip:203]:   Max refresh rate: 0
[21:08:48][C][esp32_rmt_led_strip:204]:   Number of LEDs: 1
[21:08:48][C][light:103]: Light 'test-01 Front LED'
[21:08:48][C][light:105]:   Default Transition Length: 0.0s
[21:08:48][C][light:106]:   Gamma Correct: 2.80
[21:08:48][C][template.switch:068]: Template Switch 'Pipeline'
[21:08:48][C][template.switch:091]:   Restore Mode: restore defaults to OFF
[21:08:48][C][template.switch:057]:   Optimistic: YES
[21:08:48][C][template.switch:068]: Template Switch 'Enable Voice Assistant'
[21:08:48][C][template.switch:070]:   Icon: 'mdi:assistant'
[21:08:48][C][template.switch:091]:   Restore Mode: restore defaults to ON
[21:08:48][C][template.switch:057]:   Optimistic: YES
[21:08:48][C][psram:020]: PSRAM:
[21:08:48][C][psram:021]:   Available: YES
[21:08:48][C][psram:024]:   Size: 8191 KB
[21:08:48][C][i2s_audio:028]: I2SController:
[21:08:48][C][i2s_audio:029]:   AccessMode: exclusive
[21:08:48][C][i2s_audio:030]:   Port: 0
[21:08:48][C][i2s_audio:032]:   Reader registered.
[21:08:48][C][i2s_audio:028]: I2SController:
[21:08:48][C][i2s_audio:029]:   AccessMode: exclusive
[21:08:48][C][i2s_audio:030]:   Port: 1
[21:08:48][C][i2s_audio:035]:   Writer registered.
[21:08:48][C][i2s_audio:138]: I2S-Writer (Initial-CFG):
[21:08:48][C][i2s_audio:140]:   sample-rate: 16000 bits_per_sample: 32
[21:08:48][C][i2s_audio:141]:   channel_fmt: 0 channels: 2
[21:08:48][C][i2s_audio:142]:   use_apll: no, use_pdm: no
[21:08:48][C][i2s_audio:135]: I2S-Reader (Initial-CFG):
[21:08:48][C][i2s_audio:140]:   sample-rate: 16000 bits_per_sample: 32
[21:08:48][C][i2s_audio:141]:   channel_fmt: 3 channels: 1
[21:08:48][C][i2s_audio:142]:   use_apll: no, use_pdm: no
[21:08:48][C][restart.button:017]: Restart Button 'test-01 REBOOT'
[21:08:48][C][mdns:115]: mDNS:
[21:08:48][C][mdns:116]:   Hostname: test-01
[21:08:48][C][ota:096]: Over-The-Air Updates:
[21:08:48][C][ota:097]:   Address: test-01.local:3232
[21:08:48][C][ota:100]:   Using Password.
[21:08:48][C][ota:103]:   OTA version: 2.
[21:08:48][C][api:139]: API Server:
[21:08:48][C][api:140]:   Address: test-01.local:6053
[21:08:48][C][api:142]:   Using noise encryption: YES
[21:08:48][C][micro_wake_word:057]: microWakeWord:
[21:08:48][C][micro_wake_word:058]:   Wake Word: okay nabu
[21:08:48][C][micro_wake_word:059]:   Probability cutoff: 0.500
[21:08:48][C][micro_wake_word:060]:   Sliding window size: 10
[21:08:48][C][esp_adf_pipeline.microphone:020]: ADF-Microphone
[21:08:48][C][adf_media_player:016]: ESP-ADF-MediaPlayer:
[21:08:48][C][adf_media_player:018]:   Number of ASPComponents: 3
[21:08:51][D][api:102]: Accepted 192.168.207.101
[21:08:51][D][api.connection:1321]: Home Assistant 2024.5.5 (192.168.207.101): Connected successfully
[21:08:51][D][micro_wake_word:177]: State changed from IDLE to START_MICROPHONE
[21:08:51][D][light:036]: 'test-01 Front LED' Setting:
[21:08:51][D][light:051]:   Brightness: 25%
[21:08:51][D][light:059]:   Red: 0%, Green: 0%, Blue: 100%
[21:08:51][D][micro_wake_word:115]: Starting Microphone
[21:08:51][D][esp_adf_pipeline:050]: Starting request, current state UNINITIALIZED
[21:08:51][D][esp-idf:000]: I (10976) I2S: DMA Malloc info, datalen=blocksize=1024, dma_buf_count=4

[21:08:52][D][i2s_audio:072]: Installing driver : yes
[21:08:52][D][esp_adf_pipeline:358]: pipeline tag 0, i2s_in
[21:08:52][D][esp_adf_pipeline:358]: pipeline tag 1, pcm_reader
[21:08:52][D][esp-idf:000]: I (10988) AUDIO_PIPELINE: link el->rb, el:0x3d8178b0, tag:i2s_in, rb:0x3d817b8c

[21:08:52][D][esp_adf_pipeline:370]: Setting up event listener.
[21:08:52][D][esp_adf_pipeline:302]: State changed from UNINITIALIZED to PREPARING
[21:08:52][D][micro_wake_word:177]: State changed from START_MICROPHONE to STARTING_MICROPHONE
[21:08:52][D][esp_audio_sinks:053]: Set bitdepth to 32
[21:08:52][D][esp_adf_pipeline:302]: State changed from PREPARING to STARTING
[21:08:52][D][esp-idf:000]: I (11005) AUDIO_ELEMENT: [i2s_in-0x3d8178b0] Element task created

[21:08:52][D][esp-idf:000]: I (11007) AUDIO_ELEMENT: [pcm_reader-0x3d817a44] Element task created

[21:08:52][D][esp-idf:000]: I (11009) AUDIO_PIPELINE: Func:audio_pipeline_run, Line:359, MEM Total:8451851 Bytes, Inter:163104 Bytes, Dram:163104 Bytes


[21:08:52][D][esp-idf:000][i2s_in]: I (11012) AUDIO_ELEMENT: [i2s_in] AEL_MSG_CMD_RESUME,state:1

[21:08:52][D][esp-idf:000]: I (11015) AUDIO_PIPELINE: Pipeline started

[21:08:52][I][esp_adf_pipeline:214]: [ pcm_reader ] status: 12
[21:08:52][D][esp_adf_pipeline:131]: Check element [i2s_in] status, 3
[21:08:52][D][esp_adf_pipeline:131]: Check element [pcm_reader] status, 3
[21:08:52][D][esp_adf_pipeline:302]: State changed from STARTING to RUNNING
[21:08:52][D][micro_wake_word:177]: State changed from STARTING_MICROPHONE to DETECTING_WAKE_WORD
[21:08:52][I][esp_adf_pipeline:214]: [ pcm_reader ] status: 12
[21:08:52][I][esp_adf_pipeline:214]: [ i2s_in ] status: 12
[21:09:14][D][micro_wake_word:362]: Wake word sliding average probability is 0.522 and most recent probability is 1.000
[21:09:14][D][micro_wake_word:128]: Wake Word Detected
[21:09:14][D][micro_wake_word:177]: State changed from DETECTING_WAKE_WORD to STOP_MICROPHONE
[21:09:14][D][micro_wake_word:134]: Stopping Microphone
[21:09:14][D][esp_adf_pipeline:302]: State changed from RUNNING to STOPPING
[21:09:14][D][micro_wake_word:177]: State changed from STOP_MICROPHONE to STOPPING_MICROPHONE
[21:09:14][D][esp-idf:000][i2s_in]: W (33041) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:14][D][esp-idf:000][i2s_in]: W (33044) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:14][D][esp-idf:000][i2s_in]: W (33047) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:14][D][esp-idf:000][i2s_in]: W (33050) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:14][D][esp_adf_pipeline:302]: State changed from STOPPING to STOPPED
[21:09:14][D][micro_wake_word:177]: State changed from STOPPING_MICROPHONE to IDLE
[21:09:14][D][media_player:061]: 'media_player' - Setting
[21:09:14][D][media_player:065]:   Command: STOP
[21:09:14][D][esp_adf_pipeline:085]: Called 'stop' while in UNINITIALIZED state.
[21:09:14][D][light:036]: 'test-01 Front LED' Setting:
[21:09:14][D][light:051]:   Brightness: 75%
[21:09:14][D][light:059]:   Red: 0%, Green: 100%, Blue: 0%
[21:09:14][D][light:109]:   Effect: 'Pulse'
[21:09:14][D][voice_assistant:502]: State changed from IDLE to START_MICROPHONE
[21:09:14][D][voice_assistant:508]: Desired state set to START_PIPELINE
[21:09:14][D][voice_assistant:220]: Starting Microphone
[21:09:14][D][ring_buffer:024]: Created ring buffer with size 32768
[21:09:14][D][esp_adf_pipeline:050]: Starting request, current state STOPPED
[21:09:14][D][esp_adf_pipeline:302]: State changed from STOPPED to PREPARING
[21:09:14][D][voice_assistant:502]: State changed from START_MICROPHONE to STARTING_MICROPHONE
[21:09:14][D][esp_adf_pipeline:302]: State changed from PREPARING to STARTING
[21:09:14][D][esp-idf:000]: I (33111) AUDIO_PIPELINE: Func:audio_pipeline_run, Line:359, MEM Total:8422123 Bytes, Inter:168276 Bytes, Dram:168276 Bytes


[21:09:14][D][esp-idf:000][i2s_in]: I (33115) AUDIO_ELEMENT: [i2s_in] AEL_MSG_CMD_RESUME,state:1

[21:09:14][D][esp-idf:000]: I (33117) AUDIO_PIPELINE: Pipeline started

[21:09:14][I][esp_adf_pipeline:214]: [ pcm_reader ] status: 14
[21:09:14][I][esp_adf_pipeline:214]: [ i2s_in ] status: 14
[21:09:14][I][esp_adf_pipeline:214]: [ i2s_in ] status: 12
[21:09:14][D][esp_adf_pipeline:131]: Check element [i2s_in] status, 3
[21:09:14][D][esp_adf_pipeline:131]: Check element [pcm_reader] status, 3
[21:09:14][D][esp_adf_pipeline:302]: State changed from STARTING to RUNNING
[21:09:14][D][voice_assistant:502]: State changed from STARTING_MICROPHONE to START_PIPELINE
[21:09:14][I][esp_adf_pipeline:214]: [ pcm_reader ] status: 12
[21:09:14][D][voice_assistant:274]: Requesting start...
[21:09:14][D][voice_assistant:502]: State changed from START_PIPELINE to STARTING_PIPELINE
[21:09:14][D][voice_assistant:523]: Client started, streaming microphone
[21:09:14][D][voice_assistant:502]: State changed from STARTING_PIPELINE to STREAMING_MICROPHONE
[21:09:14][D][voice_assistant:508]: Desired state set to STREAMING_MICROPHONE
[21:09:14][D][voice_assistant:625]: Event Type: 1
[21:09:14][D][voice_assistant:628]: Assist Pipeline running
[21:09:14][D][voice_assistant:625]: Event Type: 3
[21:09:14][D][voice_assistant:639]: STT started
[21:09:14][D][light:036]: 'test-01 Front LED' Setting:
[21:09:14][D][light:051]:   Brightness: 25%
[21:09:14][D][light:059]:   Red: 0%, Green: 0%, Blue: 100%
[21:09:14][D][light:109]:   Effect: 'Wakeword'
[21:09:14][D][voice_assistant:625]: Event Type: 11
[21:09:14][D][voice_assistant:779]: Starting STT by VAD
[21:09:16][D][voice_assistant:625]: Event Type: 12
[21:09:16][D][voice_assistant:783]: STT by VAD end
[21:09:16][D][voice_assistant:502]: State changed from STREAMING_MICROPHONE to STOP_MICROPHONE
[21:09:16][D][voice_assistant:508]: Desired state set to AWAITING_RESPONSE
[21:09:16][D][esp_adf_pipeline:302]: State changed from RUNNING to STOPPING
[21:09:16][D][voice_assistant:502]: State changed from STOP_MICROPHONE to STOPPING_MICROPHONE
[21:09:16][D][esp-idf:000][i2s_in]: W (35138) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:16][D][esp-idf:000][i2s_in]: W (35141) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:16][D][esp-idf:000][i2s_in]: W (35146) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:16][D][esp-idf:000][i2s_in]: W (35150) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:16][D][esp_adf_pipeline:302]: State changed from STOPPING to STOPPED
[21:09:16][D][voice_assistant:502]: State changed from STOPPING_MICROPHONE to AWAITING_RESPONSE
[21:09:16][D][voice_assistant:625]: Event Type: 4
[21:09:16][D][voice_assistant:653]: Speech recognised as: "Zet licht in het kantoor uit?"
[21:09:16][D][voice_assistant:625]: Event Type: 5
[21:09:16][D][voice_assistant:658]: Intent started
[21:09:19][D][voice_assistant:625]: Event Type: 6
[21:09:19][D][voice_assistant:625]: Event Type: 7
[21:09:19][D][voice_assistant:681]: Response: "Het licht in het kantoor is uitgeschakeld."
[21:09:19][D][light:036]: 'test-01 Front LED' Setting:
[21:09:19][D][light:051]:   Brightness: 75%
[21:09:19][D][light:059]:   Red: 0%, Green: 100%, Blue: 0%
[21:09:19][D][light:109]:   Effect: 'Pulse'
[21:09:19][D][voice_assistant:625]: Event Type: 8
[21:09:19][D][voice_assistant:701]: Response URL: "http://192.168.207.101:8123/api/tts_proxy/80ccb868b538746ae77149736cbb3987d8494075_nl-nl_f57ed9f7cb_tts.home_assistant_cloud.mp3"
[21:09:19][D][voice_assistant:502]: State changed from AWAITING_RESPONSE to STREAMING_RESPONSE
[21:09:19][D][voice_assistant:508]: Desired state set to STREAMING_RESPONSE
[21:09:19][D][media_player:061]: 'media_player' - Setting
[21:09:19][D][media_player:068]:   Media URL: http://192.168.207.101:8123/api/tts_proxy/80ccb868b538746ae77149736cbb3987d8494075_nl-nl_f57ed9f7cb_tts.home_assistant_cloud.mp3
[21:09:19][D][media_player:074]:  Announcement: yes
[21:09:19][D][adf_media_player:030]: Got control call in state 1
[21:09:19][D][esp_adf_pipeline:050]: Starting request, current state UNINITIALIZED
[21:09:19][D][esp-idf:000]: I (38335) MP3_DECODER: MP3 init

[21:09:19][D][esp-idf:000]: I (38339) I2S: DMA Malloc info, datalen=blocksize=2048, dma_buf_count=4

[21:09:19][D][i2s_audio:072]: Installing driver : yes
[21:09:19][D][esp_adf_pipeline:358]: pipeline tag 0, http
[21:09:19][D][esp_adf_pipeline:358]: pipeline tag 1, decoder
[21:09:19][D][esp_adf_pipeline:358]: pipeline tag 2, resampler
[21:09:19][D][esp_adf_pipeline:358]: pipeline tag 3, i2s_out
[21:09:19][D][esp-idf:000]: I (38356) AUDIO_PIPELINE: link el->rb, el:0x3d820ed8, tag:http, rb:0x3d8215a8

[21:09:19][D][esp-idf:000]: I (38358) AUDIO_PIPELINE: link el->rb, el:0x3d8210dc, tag:decoder, rb:0x3d8225e8

[21:09:19][D][esp-idf:000]: I (38361) AUDIO_PIPELINE: link el->rb, el:0x3d821278, tag:resampler, rb:0x3d823628

[21:09:19][D][esp_adf_pipeline:370]: Setting up event listener.
[21:09:19][D][esp_adf_pipeline:302]: State changed from UNINITIALIZED to PREPARING
[21:09:19][I][adf_media_player:135]: got new pipeline state: 1
[21:09:19][D][adf_i2s_out:127]: Set final i2s settings: 16000
[21:09:19][D][esp_audio_processors:079]: New settings: SRC: rate: 16000, ch: 2 DST: rate: 16000, ch: 2 
[21:09:19][W][component:237]: Component voice_assistant took a long time for an operation (55 ms).
[21:09:19][W][component:238]: Components should block for at most 30 ms.
[21:09:19][D][voice_assistant:625]: Event Type: 2
[21:09:19][D][voice_assistant:715]: Assist Pipeline ended
[21:09:19][D][esp-idf:000]: I (38392) AUDIO_THREAD: The http task allocate stack on external memory

[21:09:19][D][esp-idf:000]: I (38394) AUDIO_ELEMENT: [http-0x3d820ed8] Element task created

[21:09:19][D][esp-idf:000]: I (38398) AUDIO_THREAD: The decoder task allocate stack on external memory

[21:09:19][D][esp-idf:000]: I (38401) AUDIO_ELEMENT: [decoder-0x3d8210dc] Element task created

[21:09:19][D][esp-idf:000][http]: I (38404) AUDIO_ELEMENT: [http] AEL_MSG_CMD_RESUME,state:1

[21:09:19][D][esp-idf:000][decoder]: I (38407) AUDIO_ELEMENT: [decoder] AEL_MSG_CMD_RESUME,state:1

[21:09:19][D][esp_aud:000]d]: 
ERROR Fatal error: protocol.data_received() call failed.
protocol: <aioesphomeapi._frame_helper.noise.APINoiseFrameHelper object at 0x7fa4dc080670>
transport: <_SelectorSocketTransport fd=6 read=polling write=<idle, bufsize=0>>
Traceback (most recent call last):
  File "/usr/lib/python3.11/asyncio/selector_events.py", line 1009, in _read_ready__data_received
    self._protocol.data_received(data)
  File "aioesphomeapi/_frame_helper/noise.py", line 136, in aioesphomeapi._frame_helper.noise.APINoiseFrameHelper.data_received
  File "aioesphomeapi/_frame_helper/noise.py", line 163, in aioesphomeapi._frame_helper.noise.APINoiseFrameHelper.data_received
  File "aioesphomeapi/_frame_helper/noise.py", line 319, in aioesphomeapi._frame_helper.noise.APINoiseFrameHelper._handle_frame
  File "/usr/local/lib/python3.11/dist-packages/noise/state.py", line 74, in decrypt_with_ad
    plaintext = self.cipher.decrypt(self.k, self.n, ad, ciphertext)
                ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
  File "/usr/local/lib/python3.11/dist-packages/noise/backends/default/ciphers.py", line 13, in decrypt
    return self.cipher.decrypt(nonce=self.format_nonce(n), data=ciphertext, associated_data=ad)
           ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
  File "src/chacha20poly1305_reuseable/__init__.py", line 127, in chacha20poly1305_reuseable.ChaCha20Poly1305Reusable.decrypt
  File "src/chacha20poly1305_reuseable/__init__.py", line 147, in chacha20poly1305_reuseable.ChaCha20Poly1305Reusable.decrypt
  File "src/chacha20poly1305_reuseable/__init__.py", line 263, in chacha20poly1305_reuseable._decrypt_with_fixed_nonce_len
  File "src/chacha20poly1305_reuseable/__init__.py", line 273, in chacha20poly1305_reuseable._decrypt_data
cryptography.exceptions.InvalidTag
WARNING test-01 @ 192.168.207.246: Connection error occurred: test-01 @ 192.168.207.246: Invalid encryption key: received_name=test-01
INFO Processing unexpected disconnect from ESPHome API for test-01 @ 192.168.207.246
WARNING Disconnected from API
INFO Successfully connected to test-01 @ 192.168.207.246 in 0.004s
INFO Successful handshake with test-01 @ 192.168.207.246 in 0.105s
[21:09:19][I][esp_adf_pipeline:214]: [ i2s_out ] status: 12
[21:09:19][D][esp_adf_pipeline:131]: Check element [http] status, 2
[21:09:19][I][esp_adf_pipeline:214]: [ resampler ] status: 12
[21:09:19][D][esp_adf_pipeline:131]: Check element [http] status, 2
[21:09:19][D][esp-idf:000][http]: I (38612) HTTP_CLIENT: Body received in fetch header state, 0x3fcc511b, 1841

[21:09:19][D][esp-idf:000][http]: I (38617) HTTP_STREAM: total_bytes=23199

[21:09:19][I][esp_adf_pipeline:214]: [ http ] status: 12
[21:09:19][D][esp_adf_pipeline:131]: Check element [http] status, 3
[21:09:19][D][esp_adf_pipeline:131]: Check element [decoder] status, 2
[21:09:19][I][esp_adf_pipeline:214]: [ decoder ] status: 12
[21:09:19][D][esp_adf_pipeline:131]: Check element [http] status, 3
[21:09:19][D][esp_adf_pipeline:131]: Check element [decoder] status, 3
[21:09:19][D][esp_adf_pipeline:131]: Check element [resampler] status, 3
[21:09:19][D][esp_adf_pipeline:131]: Check element [i2s_out] status, 3
[21:09:19][D][esp_adf_pipeline:302]: State changed from STARTING to RUNNING
[21:09:19][I][adf_media_player:135]: got new pipeline state: 3
[21:09:19][D][adf_i2s_out:127]: Set final i2s settings: 24000
[21:09:19][D][esp_audio_processors:079]: New settings: SRC: rate: 24000, ch: 1 DST: rate: 24000, ch: 1 
[21:09:19][I][HTTPStreamReader:129]: [ * ] Receive music info from mp3 decoder, sample_rates=24000, bits=16, ch=1
[21:09:19][D][adf_i2s_out:127]: Set final i2s settings: 24000
[21:09:19][D][esp_audio_processors:079]: New settings: SRC: rate: 24000, ch: 1 DST: rate: 24000, ch: 1 
[21:09:22][D][esp-idf:000][http]: W (41118) HTTP_STREAM: No more data,errno:0, total_bytes:23199, rlen = 0

[21:09:22][D][esp-idf:000][http]: I (41123) AUDIO_ELEMENT: IN-[http] AEL_IO_DONE,0

[21:09:22][I][esp_adf_pipeline:214]: [ http ] status: 15
[21:09:22][D][esp_adf_pipeline:302]: State changed from RUNNING to STOPPING
[21:09:22][I][adf_media_player:135]: got new pipeline state: 4
[21:09:22][D][esp-idf:000][decoder]: I (41799) AUDIO_ELEMENT: IN-[decoder] AEL_IO_DONE,-2

[21:09:23][D][esp-idf:000][decoder]: I (42161) MP3_DECODER: Closed

[21:09:23][D][esp-idf:000][resampler]: I (42267) AUDIO_ELEMENT: IN-[resampler] AEL_IO_DONE,-2

[21:09:23][D][esp-idf:000][i2s_out]: I (42330) AUDIO_ELEMENT: IN-[i2s_out] AEL_IO_DONE,-2

[21:09:23][D][esp_adf_pipeline:302]: State changed from STOPPING to STOPPED
[21:09:23][I][adf_media_player:135]: got new pipeline state: 5
[21:09:23][D][light:036]: 'test-01 Front LED' Setting:
[21:09:23][D][light:047]:   State: ON
[21:09:23][D][light:051]:   Brightness: 25%
[21:09:23][D][light:059]:   Red: 0%, Green: 0%, Blue: 100%
[21:09:23][D][micro_wake_word:177]: State changed from IDLE to START_MICROPHONE
[21:09:23][D][micro_wake_word:115]: Starting Microphone
[21:09:23][D][esp_adf_pipeline:050]: Starting request, current state STOPPED
[21:09:23][D][esp_adf_pipeline:302]: State changed from STOPPED to PREPARING
[21:09:23][D][micro_wake_word:177]: State changed from START_MICROPHONE to STARTING_MICROPHONE
[21:09:23][D][esp_adf_pipeline:302]: State changed from PREPARING to STARTING
[21:09:23][D][esp-idf:000]: I (42537) AUDIO_PIPELINE: Func:audio_pipeline_run, Line:359, MEM Total:8376627 Bytes, Inter:152808 Bytes, Dram:152808 Bytes


[21:09:23][D][esp-idf:000][i2s_in]: I (42539) AUDIO_ELEMENT: [i2s_in] AEL_MSG_CMD_RESUME,state:1

[21:09:23][D][esp-idf:000]: I (42543) AUDIO_PIPELINE: Pipeline started

[21:09:23][I][esp_adf_pipeline:214]: [ pcm_reader ] status: 14
[21:09:23][I][esp_adf_pipeline:214]: [ i2s_in ] status: 14
[21:09:23][I][esp_adf_pipeline:214]: [ i2s_in ] status: 12
[21:09:23][D][esp_adf_pipeline:131]: Check element [i2s_in] status, 3
[21:09:23][D][esp_adf_pipeline:131]: Check element [pcm_reader] status, 3
[21:09:23][D][esp_adf_pipeline:302]: State changed from STARTING to RUNNING
[21:09:23][D][micro_wake_word:177]: State changed from STARTING_MICROPHONE to DETECTING_WAKE_WORD
[21:09:23][I][esp_adf_pipeline:214]: [ pcm_reader ] status: 12
[21:09:25][D][micro_wake_word:362]: Wake word sliding average probability is 0.585 and most recent probability is 1.000
[21:09:25][D][micro_wake_word:128]: Wake Word Detected
[21:09:25][D][micro_wake_word:177]: State changed from DETECTING_WAKE_WORD to STOP_MICROPHONE
[21:09:25][D][micro_wake_word:134]: Stopping Microphone
[21:09:25][D][esp_adf_pipeline:302]: State changed from RUNNING to STOPPING
[21:09:25][D][micro_wake_word:177]: State changed from STOP_MICROPHONE to STOPPING_MICROPHONE
[21:09:25][D][esp-idf:000][i2s_in]: W (44496) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:25][D][esp-idf:000][i2s_in]: W (44499) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:25][D][esp-idf:000][i2s_in]: W (44503) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:25][D][esp-idf:000][i2s_in]: W (44506) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:25][D][esp_adf_pipeline:302]: State changed from STOPPING to STOPPED
[21:09:25][D][micro_wake_word:177]: State changed from STOPPING_MICROPHONE to IDLE
[21:09:25][D][media_player:061]: 'media_player' - Setting
[21:09:25][D][media_player:065]:   Command: STOP
[21:09:25][D][esp_adf_pipeline:085]: Called 'stop' while in STOPPED state.
[21:09:25][D][light:036]: 'test-01 Front LED' Setting:
[21:09:25][D][light:051]:   Brightness: 75%
[21:09:25][D][light:059]:   Red: 0%, Green: 100%, Blue: 0%
[21:09:25][D][light:109]:   Effect: 'Pulse'

Does anyone know what's going on here?

@indevor
Copy link

indevor commented May 30, 2024

Hey, based on the config above I have been cooking this:

substitutions:
  device_name: "test-01"
  friendly_name: "test-01"
  device_description: "esp32s3"
  esp_board: "esp32-s3-devkitc-1"
  # Phases of the Voice Assistant
  # IDLE: The voice assistant is ready to be triggered by a wake-word
  voice_assist_idle_phase_id: '1'
  # LISTENING: The voice assistant is ready to listen to a voice command (after being triggered by the wake word)
  voice_assist_listening_phase_id: '2'
  # THINKING: The voice assistant is currently processing the command
  voice_assist_thinking_phase_id: '3'
  # REPLYING: The voice assistant is replying to the command
  voice_assist_replying_phase_id: '4'
  # NOT_READY: The voice assistant is not ready
  voice_assist_not_ready_phase_id: '10'
  # ERROR: The voice assistant encountered an error
  voice_assist_error_phase_id: '11'
  # MUTED: The voice assistant is muted and will not reply to a wake-word
  voice_assist_muted_phase_id: '12'

external_components:
  - source:
      type: git
      url: https://github.com/gnumpi/esphome_audio
      ref: main
      #type: local
      #path: /Users/siekmann/Privat/Projects/espHome/esphome_audio/esphome/components
    components: [ adf_pipeline, i2s_audio ]

esphome:
  name: ${device_name}
  comment: ${device_description}
  friendly_name: ${friendly_name}
  min_version: 2024.2.0
  platformio_options:
    build_flags: -DBOARD_HAS_PSRAM
    board_build.flash_mode: dio
    board_upload.maximum_size: 16777216
  on_boot:
    priority: 600
    then:
      # Run the script to refresh the LED status
      # If after 30 seconds, the device is still initializing (It did not yet connect to Home Assistant), turn off the init_in_progress variable and run the script to refresh the LED status
      - delay: 30s
      - if:
          condition:
            lambda: return id(init_in_progress);
          then:
            - lambda: id(init_in_progress) = false;
                            
esp32:
  board: ${esp_board}
  variant: ESP32S3
  flash_size: 16MB
  framework:
    type: esp-idf
    sdkconfig_options:
      # need to set a s3 compatible board for the adf-sdk to compile
      # board specific code is not used though
      CONFIG_ESP32_S3_BOX_BOARD: "y"
      CONFIG_ESP32_WIFI_STATIC_RX_BUFFER_NUM: "16"
      CONFIG_ESP32_WIFI_DYNAMIC_RX_BUFFER_NUM: "512"
      CONFIG_TCPIP_RECVMBOX_SIZE: "512"

      CONFIG_TCP_SND_BUF_DEFAULT: "65535"
      CONFIG_TCP_WND_DEFAULT: "512000"
      CONFIG_TCP_RECVMBOX_SIZE: "512"

logger:

globals:
  # Global initialisation variable. Initialized to true and set to false once everything is connected. Only used to have a smooth "plugging" experience
  - id: init_in_progress
    type: bool
    restore_value: no
    initial_value: 'true'
  # Global variable tracking the phase of the voice assistant (defined above). Initialized to not_ready
  - id: voice_assistant_phase
    type: int
    restore_value: no
    initial_value: ${voice_assist_not_ready_phase_id}

psram:
  mode: octal
  speed: 80MHz

wifi:
  enable_rrm: true
  ssid: !secret wifi_ssid
  password: !secret wifi_password
  fast_connect: true

ota:
  password: !secret ota_password

api:
  encryption:
    key: !secret api_key

i2s_audio:
  - id: i2s_in
    i2s_lrclk_pin: GPIO7
    i2s_bclk_pin: GPIO16
  - id: i2s_out
    i2s_lrclk_pin: GPIO8
    i2s_bclk_pin: GPIO18

adf_pipeline:
  - platform: i2s_audio
    type: audio_out
    id: adf_i2s_out
    i2s_audio_id: i2s_out
    i2s_dout_pin: GPIO17

  - platform: i2s_audio
    type: audio_in
    id: adf_i2s_in
    i2s_audio_id: i2s_in
    i2s_din_pin: GPIO15
    pdm: false
    channel: right
    sample_rate: 16000
    bits_per_sample: 32bit

microphone:
  - platform: adf_pipeline
    id: adf_microphone
    keep_pipeline_alive: true
    pipeline:
      - adf_i2s_in
      - self
      
media_player:
  - platform: adf_pipeline
    id: adf_media_player
    name: media_player
    keep_pipeline_alive: true
    internal: false
    pipeline:
      - self
      - resampler
      - adf_i2s_out

micro_wake_word:
  model: okay_nabu
  on_wake_word_detected:
      - media_player.stop:
      - light.turn_on:
          id: led_ring
          blue: 0%
          red: 0%
          green: 100%
          brightness: 75%
          effect: pulse
      - voice_assistant.start:

voice_assistant:
  microphone: adf_microphone
  media_player: adf_media_player
  use_wake_word: false
  #vad_threshold: 3
  #noise_suppression_level: 1
  auto_gain: 31dBFS
  #volume_multiplier: 15.0

  on_client_connected:
    - lambda: id(init_in_progress) = false;
    - if:
        condition:
          switch.is_on: use_wake_word
        then:
          - micro_wake_word.start:
          - lambda: id(voice_assistant_phase) = ${voice_assist_idle_phase_id};
          - script.execute: reset_led
        else:
          - lambda: id(voice_assistant_phase) = ${voice_assist_muted_phase_id};

  on_client_disconnected:
    - lambda: id(voice_assistant_phase) = ${voice_assist_not_ready_phase_id};
    - voice_assistant.stop
    - micro_wake_word.stop
    - light.turn_on:
          id: led_ring
          blue: 0%
          red: 100%
          green: 100%
          brightness: 50%
          effect: connecting

  on_listening:
    - light.turn_on:
        id: led_ring
        blue: 100%
        red: 0%
        green: 0%
        brightness: 25%
        effect: wakeword
        
  on_tts_start:
    - light.turn_on:
        id: led_ring
        blue: 0%
        red: 0%
        green: 100%
        brightness: 75%
        effect: pulse
  
  on_end:
      then:
        - light.turn_off:
            id: led_ring
        - voice_assistant.stop
        - wait_until:
            not:
              media_player.is_playing:
        - script.execute: reset_led
        - if:
            condition:
              switch.is_on: use_wake_word
            then:
              - micro_wake_word.start:
  on_error:
    - light.turn_on:
        id: led_ring
        blue: 0%
        red: 100%
        green: 0%
        brightness: 100%
        effect: none
    - delay: 1s
    - script.execute: reset_led
    - script.wait: reset_led
    - lambda: |-
        if (code == "wake-provider-missing" || code == "wake-engine-missing") {
          id(use_wake_word).turn_off();
        }
    - if:
        condition:
          switch.is_on: use_wake_word
        then:
          - micro_wake_word.start:
          - script.execute: reset_led
              
script:
  - id: reset_led
    then:
      - if:
          condition:
            switch.is_on: use_wake_word
          then:
            - light.turn_on:
                id: led_ring
                blue: 100%
                red: 0%
                green: 0%
                brightness: 25%
                effect: none
          else:
            - light.turn_off: led_ring
 
button:
  - platform: restart
    id: restart_btn
    name: "${friendly_name} REBOOT"
            
switch:
  - platform: template
    name: Enable Voice Assistant
    id: use_wake_word
    optimistic: true
    restore_mode: RESTORE_DEFAULT_ON
    icon: mdi:assistant
    # When the switch is turned on (on Home Assistant):
    # Start the voice assistant component
    # Set the correct phase and run the script to refresh the LED status
    on_turn_on:
      - logger.log: "switch on"
      - if:
          condition:
            lambda: return !id(init_in_progress);
          then:
            - logger.log: "condition 1"
            - lambda: id(voice_assistant_phase) = ${voice_assist_idle_phase_id};
            - voice_assistant.stop
            - delay: 1s
            - if:
                condition:
                  not:
                    - voice_assistant.is_running
                then:
                  - logger.log: "Starting MWW"
                  #- voice_assistant.start_continuous
                  - micro_wake_word.start:
      - script.execute: reset_led
    on_turn_off:
      - if:
          condition:
            lambda: return !id(init_in_progress);
          then:
            - voice_assistant.stop
            - micro_wake_word.stop
            - lambda: id(voice_assistant_phase) = ${voice_assist_muted_phase_id};
      - script.execute: reset_led

  - platform: template
    name: Pipeline
    id: pipeline_switch
    optimistic: true
    restore_mode: RESTORE_DEFAULT_OFF

    on_turn_off:
      - media_player.stop

light:
  - platform: esp32_rmt_led_strip
    id: led_ring
    name: "${friendly_name} Front LED"
    pin: GPIO05
    num_leds: 1
    rmt_channel: 1
    rgb_order: GRB
    chipset: ws2812
    default_transition_length: 0s
    effects:
      - pulse:
          name: "Pulse"
          transition_length: 0.5s
          update_interval: 0.5s
      - addressable_twinkle:
          name: "Working"
          twinkle_probability: 5%
          progress_interval: 4ms
      - addressable_color_wipe:
          name: "Wakeword"
          colors:
            - red: 0%
              green: 50%
              blue: 0%
              num_leds: 12
          add_led_interval: 20ms
          reverse: false
      - addressable_color_wipe:
          name: "Connecting"
          colors:
            - red: 60%
              green: 60%
              blue: 60%
              num_leds: 1
            - red: 60%
              green: 60%
              blue: 0%
              num_leds: 1
          add_led_interval: 100ms
          reverse: true

This works extremely well, but just once ;)

The second time, it detects the wake word, starts blinking green, does not process the request and keeps blinking.

LOG (after trying twice)

INFO ESPHome 2024.5.4
[21:08:48][I][app:100]: ESPHome version 2024.5.4 compiled on May 30 2024, 21:05:15
[21:08:48][C][wifi:580]: WiFi:
[21:08:48][C][wifi:408]:   Local MAC: 3C:84:27:CC:42:0C
[21:08:48][C][wifi:413]:   SSID: [redacted]
[21:08:48][C][wifi:416]:   IP Address: 192.168.207.246
[21:08:48][C][wifi:420]:   BSSID: [redacted]
[21:08:48][C][wifi:421]:   Hostname: 'test-01'
[21:08:48][C][wifi:423]:   Signal strength: -60 dB ▂▄▆█
[21:08:48][C][wifi:427]:   Channel: 11
[21:08:48][C][wifi:428]:   Subnet: 255.255.255.0
[21:08:48][C][wifi:429]:   Gateway: 192.168.207.1
[21:08:48][C][wifi:430]:   DNS1: 192.168.207.130
[21:08:48][C][wifi:431]:   DNS2: 0.0.0.0
[21:08:48][C][wifi:433]:   BTM: disabled
[21:08:48][C][wifi:434]:   RRM: enabled
[21:08:48][C][logger:185]: Logger:
[21:08:48][C][logger:186]:   Level: DEBUG
[21:08:48][C][logger:188]:   Log Baud Rate: 115200
[21:08:48][C][logger:189]:   Hardware UART: USB_SERIAL_JTAG
[21:08:48][C][esp32_rmt_led_strip:175]: ESP32 RMT LED Strip:
[21:08:48][C][esp32_rmt_led_strip:176]:   Pin: 5
[21:08:48][C][esp32_rmt_led_strip:177]:   Channel: 1
[21:08:48][C][esp32_rmt_led_strip:202]:   RGB Order: GRB
[21:08:48][C][esp32_rmt_led_strip:203]:   Max refresh rate: 0
[21:08:48][C][esp32_rmt_led_strip:204]:   Number of LEDs: 1
[21:08:48][C][light:103]: Light 'test-01 Front LED'
[21:08:48][C][light:105]:   Default Transition Length: 0.0s
[21:08:48][C][light:106]:   Gamma Correct: 2.80
[21:08:48][C][template.switch:068]: Template Switch 'Pipeline'
[21:08:48][C][template.switch:091]:   Restore Mode: restore defaults to OFF
[21:08:48][C][template.switch:057]:   Optimistic: YES
[21:08:48][C][template.switch:068]: Template Switch 'Enable Voice Assistant'
[21:08:48][C][template.switch:070]:   Icon: 'mdi:assistant'
[21:08:48][C][template.switch:091]:   Restore Mode: restore defaults to ON
[21:08:48][C][template.switch:057]:   Optimistic: YES
[21:08:48][C][psram:020]: PSRAM:
[21:08:48][C][psram:021]:   Available: YES
[21:08:48][C][psram:024]:   Size: 8191 KB
[21:08:48][C][i2s_audio:028]: I2SController:
[21:08:48][C][i2s_audio:029]:   AccessMode: exclusive
[21:08:48][C][i2s_audio:030]:   Port: 0
[21:08:48][C][i2s_audio:032]:   Reader registered.
[21:08:48][C][i2s_audio:028]: I2SController:
[21:08:48][C][i2s_audio:029]:   AccessMode: exclusive
[21:08:48][C][i2s_audio:030]:   Port: 1
[21:08:48][C][i2s_audio:035]:   Writer registered.
[21:08:48][C][i2s_audio:138]: I2S-Writer (Initial-CFG):
[21:08:48][C][i2s_audio:140]:   sample-rate: 16000 bits_per_sample: 32
[21:08:48][C][i2s_audio:141]:   channel_fmt: 0 channels: 2
[21:08:48][C][i2s_audio:142]:   use_apll: no, use_pdm: no
[21:08:48][C][i2s_audio:135]: I2S-Reader (Initial-CFG):
[21:08:48][C][i2s_audio:140]:   sample-rate: 16000 bits_per_sample: 32
[21:08:48][C][i2s_audio:141]:   channel_fmt: 3 channels: 1
[21:08:48][C][i2s_audio:142]:   use_apll: no, use_pdm: no
[21:08:48][C][restart.button:017]: Restart Button 'test-01 REBOOT'
[21:08:48][C][mdns:115]: mDNS:
[21:08:48][C][mdns:116]:   Hostname: test-01
[21:08:48][C][ota:096]: Over-The-Air Updates:
[21:08:48][C][ota:097]:   Address: test-01.local:3232
[21:08:48][C][ota:100]:   Using Password.
[21:08:48][C][ota:103]:   OTA version: 2.
[21:08:48][C][api:139]: API Server:
[21:08:48][C][api:140]:   Address: test-01.local:6053
[21:08:48][C][api:142]:   Using noise encryption: YES
[21:08:48][C][micro_wake_word:057]: microWakeWord:
[21:08:48][C][micro_wake_word:058]:   Wake Word: okay nabu
[21:08:48][C][micro_wake_word:059]:   Probability cutoff: 0.500
[21:08:48][C][micro_wake_word:060]:   Sliding window size: 10
[21:08:48][C][esp_adf_pipeline.microphone:020]: ADF-Microphone
[21:08:48][C][adf_media_player:016]: ESP-ADF-MediaPlayer:
[21:08:48][C][adf_media_player:018]:   Number of ASPComponents: 3
[21:08:51][D][api:102]: Accepted 192.168.207.101
[21:08:51][D][api.connection:1321]: Home Assistant 2024.5.5 (192.168.207.101): Connected successfully
[21:08:51][D][micro_wake_word:177]: State changed from IDLE to START_MICROPHONE
[21:08:51][D][light:036]: 'test-01 Front LED' Setting:
[21:08:51][D][light:051]:   Brightness: 25%
[21:08:51][D][light:059]:   Red: 0%, Green: 0%, Blue: 100%
[21:08:51][D][micro_wake_word:115]: Starting Microphone
[21:08:51][D][esp_adf_pipeline:050]: Starting request, current state UNINITIALIZED
[21:08:51][D][esp-idf:000]: I (10976) I2S: DMA Malloc info, datalen=blocksize=1024, dma_buf_count=4

[21:08:52][D][i2s_audio:072]: Installing driver : yes
[21:08:52][D][esp_adf_pipeline:358]: pipeline tag 0, i2s_in
[21:08:52][D][esp_adf_pipeline:358]: pipeline tag 1, pcm_reader
[21:08:52][D][esp-idf:000]: I (10988) AUDIO_PIPELINE: link el->rb, el:0x3d8178b0, tag:i2s_in, rb:0x3d817b8c

[21:08:52][D][esp_adf_pipeline:370]: Setting up event listener.
[21:08:52][D][esp_adf_pipeline:302]: State changed from UNINITIALIZED to PREPARING
[21:08:52][D][micro_wake_word:177]: State changed from START_MICROPHONE to STARTING_MICROPHONE
[21:08:52][D][esp_audio_sinks:053]: Set bitdepth to 32
[21:08:52][D][esp_adf_pipeline:302]: State changed from PREPARING to STARTING
[21:08:52][D][esp-idf:000]: I (11005) AUDIO_ELEMENT: [i2s_in-0x3d8178b0] Element task created

[21:08:52][D][esp-idf:000]: I (11007) AUDIO_ELEMENT: [pcm_reader-0x3d817a44] Element task created

[21:08:52][D][esp-idf:000]: I (11009) AUDIO_PIPELINE: Func:audio_pipeline_run, Line:359, MEM Total:8451851 Bytes, Inter:163104 Bytes, Dram:163104 Bytes


[21:08:52][D][esp-idf:000][i2s_in]: I (11012) AUDIO_ELEMENT: [i2s_in] AEL_MSG_CMD_RESUME,state:1

[21:08:52][D][esp-idf:000]: I (11015) AUDIO_PIPELINE: Pipeline started

[21:08:52][I][esp_adf_pipeline:214]: [ pcm_reader ] status: 12
[21:08:52][D][esp_adf_pipeline:131]: Check element [i2s_in] status, 3
[21:08:52][D][esp_adf_pipeline:131]: Check element [pcm_reader] status, 3
[21:08:52][D][esp_adf_pipeline:302]: State changed from STARTING to RUNNING
[21:08:52][D][micro_wake_word:177]: State changed from STARTING_MICROPHONE to DETECTING_WAKE_WORD
[21:08:52][I][esp_adf_pipeline:214]: [ pcm_reader ] status: 12
[21:08:52][I][esp_adf_pipeline:214]: [ i2s_in ] status: 12
[21:09:14][D][micro_wake_word:362]: Wake word sliding average probability is 0.522 and most recent probability is 1.000
[21:09:14][D][micro_wake_word:128]: Wake Word Detected
[21:09:14][D][micro_wake_word:177]: State changed from DETECTING_WAKE_WORD to STOP_MICROPHONE
[21:09:14][D][micro_wake_word:134]: Stopping Microphone
[21:09:14][D][esp_adf_pipeline:302]: State changed from RUNNING to STOPPING
[21:09:14][D][micro_wake_word:177]: State changed from STOP_MICROPHONE to STOPPING_MICROPHONE
[21:09:14][D][esp-idf:000][i2s_in]: W (33041) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:14][D][esp-idf:000][i2s_in]: W (33044) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:14][D][esp-idf:000][i2s_in]: W (33047) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:14][D][esp-idf:000][i2s_in]: W (33050) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:14][D][esp_adf_pipeline:302]: State changed from STOPPING to STOPPED
[21:09:14][D][micro_wake_word:177]: State changed from STOPPING_MICROPHONE to IDLE
[21:09:14][D][media_player:061]: 'media_player' - Setting
[21:09:14][D][media_player:065]:   Command: STOP
[21:09:14][D][esp_adf_pipeline:085]: Called 'stop' while in UNINITIALIZED state.
[21:09:14][D][light:036]: 'test-01 Front LED' Setting:
[21:09:14][D][light:051]:   Brightness: 75%
[21:09:14][D][light:059]:   Red: 0%, Green: 100%, Blue: 0%
[21:09:14][D][light:109]:   Effect: 'Pulse'
[21:09:14][D][voice_assistant:502]: State changed from IDLE to START_MICROPHONE
[21:09:14][D][voice_assistant:508]: Desired state set to START_PIPELINE
[21:09:14][D][voice_assistant:220]: Starting Microphone
[21:09:14][D][ring_buffer:024]: Created ring buffer with size 32768
[21:09:14][D][esp_adf_pipeline:050]: Starting request, current state STOPPED
[21:09:14][D][esp_adf_pipeline:302]: State changed from STOPPED to PREPARING
[21:09:14][D][voice_assistant:502]: State changed from START_MICROPHONE to STARTING_MICROPHONE
[21:09:14][D][esp_adf_pipeline:302]: State changed from PREPARING to STARTING
[21:09:14][D][esp-idf:000]: I (33111) AUDIO_PIPELINE: Func:audio_pipeline_run, Line:359, MEM Total:8422123 Bytes, Inter:168276 Bytes, Dram:168276 Bytes


[21:09:14][D][esp-idf:000][i2s_in]: I (33115) AUDIO_ELEMENT: [i2s_in] AEL_MSG_CMD_RESUME,state:1

[21:09:14][D][esp-idf:000]: I (33117) AUDIO_PIPELINE: Pipeline started

[21:09:14][I][esp_adf_pipeline:214]: [ pcm_reader ] status: 14
[21:09:14][I][esp_adf_pipeline:214]: [ i2s_in ] status: 14
[21:09:14][I][esp_adf_pipeline:214]: [ i2s_in ] status: 12
[21:09:14][D][esp_adf_pipeline:131]: Check element [i2s_in] status, 3
[21:09:14][D][esp_adf_pipeline:131]: Check element [pcm_reader] status, 3
[21:09:14][D][esp_adf_pipeline:302]: State changed from STARTING to RUNNING
[21:09:14][D][voice_assistant:502]: State changed from STARTING_MICROPHONE to START_PIPELINE
[21:09:14][I][esp_adf_pipeline:214]: [ pcm_reader ] status: 12
[21:09:14][D][voice_assistant:274]: Requesting start...
[21:09:14][D][voice_assistant:502]: State changed from START_PIPELINE to STARTING_PIPELINE
[21:09:14][D][voice_assistant:523]: Client started, streaming microphone
[21:09:14][D][voice_assistant:502]: State changed from STARTING_PIPELINE to STREAMING_MICROPHONE
[21:09:14][D][voice_assistant:508]: Desired state set to STREAMING_MICROPHONE
[21:09:14][D][voice_assistant:625]: Event Type: 1
[21:09:14][D][voice_assistant:628]: Assist Pipeline running
[21:09:14][D][voice_assistant:625]: Event Type: 3
[21:09:14][D][voice_assistant:639]: STT started
[21:09:14][D][light:036]: 'test-01 Front LED' Setting:
[21:09:14][D][light:051]:   Brightness: 25%
[21:09:14][D][light:059]:   Red: 0%, Green: 0%, Blue: 100%
[21:09:14][D][light:109]:   Effect: 'Wakeword'
[21:09:14][D][voice_assistant:625]: Event Type: 11
[21:09:14][D][voice_assistant:779]: Starting STT by VAD
[21:09:16][D][voice_assistant:625]: Event Type: 12
[21:09:16][D][voice_assistant:783]: STT by VAD end
[21:09:16][D][voice_assistant:502]: State changed from STREAMING_MICROPHONE to STOP_MICROPHONE
[21:09:16][D][voice_assistant:508]: Desired state set to AWAITING_RESPONSE
[21:09:16][D][esp_adf_pipeline:302]: State changed from RUNNING to STOPPING
[21:09:16][D][voice_assistant:502]: State changed from STOP_MICROPHONE to STOPPING_MICROPHONE
[21:09:16][D][esp-idf:000][i2s_in]: W (35138) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:16][D][esp-idf:000][i2s_in]: W (35141) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:16][D][esp-idf:000][i2s_in]: W (35146) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:16][D][esp-idf:000][i2s_in]: W (35150) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:16][D][esp_adf_pipeline:302]: State changed from STOPPING to STOPPED
[21:09:16][D][voice_assistant:502]: State changed from STOPPING_MICROPHONE to AWAITING_RESPONSE
[21:09:16][D][voice_assistant:625]: Event Type: 4
[21:09:16][D][voice_assistant:653]: Speech recognised as: "Zet licht in het kantoor uit?"
[21:09:16][D][voice_assistant:625]: Event Type: 5
[21:09:16][D][voice_assistant:658]: Intent started
[21:09:19][D][voice_assistant:625]: Event Type: 6
[21:09:19][D][voice_assistant:625]: Event Type: 7
[21:09:19][D][voice_assistant:681]: Response: "Het licht in het kantoor is uitgeschakeld."
[21:09:19][D][light:036]: 'test-01 Front LED' Setting:
[21:09:19][D][light:051]:   Brightness: 75%
[21:09:19][D][light:059]:   Red: 0%, Green: 100%, Blue: 0%
[21:09:19][D][light:109]:   Effect: 'Pulse'
[21:09:19][D][voice_assistant:625]: Event Type: 8
[21:09:19][D][voice_assistant:701]: Response URL: "http://192.168.207.101:8123/api/tts_proxy/80ccb868b538746ae77149736cbb3987d8494075_nl-nl_f57ed9f7cb_tts.home_assistant_cloud.mp3"
[21:09:19][D][voice_assistant:502]: State changed from AWAITING_RESPONSE to STREAMING_RESPONSE
[21:09:19][D][voice_assistant:508]: Desired state set to STREAMING_RESPONSE
[21:09:19][D][media_player:061]: 'media_player' - Setting
[21:09:19][D][media_player:068]:   Media URL: http://192.168.207.101:8123/api/tts_proxy/80ccb868b538746ae77149736cbb3987d8494075_nl-nl_f57ed9f7cb_tts.home_assistant_cloud.mp3
[21:09:19][D][media_player:074]:  Announcement: yes
[21:09:19][D][adf_media_player:030]: Got control call in state 1
[21:09:19][D][esp_adf_pipeline:050]: Starting request, current state UNINITIALIZED
[21:09:19][D][esp-idf:000]: I (38335) MP3_DECODER: MP3 init

[21:09:19][D][esp-idf:000]: I (38339) I2S: DMA Malloc info, datalen=blocksize=2048, dma_buf_count=4

[21:09:19][D][i2s_audio:072]: Installing driver : yes
[21:09:19][D][esp_adf_pipeline:358]: pipeline tag 0, http
[21:09:19][D][esp_adf_pipeline:358]: pipeline tag 1, decoder
[21:09:19][D][esp_adf_pipeline:358]: pipeline tag 2, resampler
[21:09:19][D][esp_adf_pipeline:358]: pipeline tag 3, i2s_out
[21:09:19][D][esp-idf:000]: I (38356) AUDIO_PIPELINE: link el->rb, el:0x3d820ed8, tag:http, rb:0x3d8215a8

[21:09:19][D][esp-idf:000]: I (38358) AUDIO_PIPELINE: link el->rb, el:0x3d8210dc, tag:decoder, rb:0x3d8225e8

[21:09:19][D][esp-idf:000]: I (38361) AUDIO_PIPELINE: link el->rb, el:0x3d821278, tag:resampler, rb:0x3d823628

[21:09:19][D][esp_adf_pipeline:370]: Setting up event listener.
[21:09:19][D][esp_adf_pipeline:302]: State changed from UNINITIALIZED to PREPARING
[21:09:19][I][adf_media_player:135]: got new pipeline state: 1
[21:09:19][D][adf_i2s_out:127]: Set final i2s settings: 16000
[21:09:19][D][esp_audio_processors:079]: New settings: SRC: rate: 16000, ch: 2 DST: rate: 16000, ch: 2 
[21:09:19][W][component:237]: Component voice_assistant took a long time for an operation (55 ms).
[21:09:19][W][component:238]: Components should block for at most 30 ms.
[21:09:19][D][voice_assistant:625]: Event Type: 2
[21:09:19][D][voice_assistant:715]: Assist Pipeline ended
[21:09:19][D][esp-idf:000]: I (38392) AUDIO_THREAD: The http task allocate stack on external memory

[21:09:19][D][esp-idf:000]: I (38394) AUDIO_ELEMENT: [http-0x3d820ed8] Element task created

[21:09:19][D][esp-idf:000]: I (38398) AUDIO_THREAD: The decoder task allocate stack on external memory

[21:09:19][D][esp-idf:000]: I (38401) AUDIO_ELEMENT: [decoder-0x3d8210dc] Element task created

[21:09:19][D][esp-idf:000][http]: I (38404) AUDIO_ELEMENT: [http] AEL_MSG_CMD_RESUME,state:1

[21:09:19][D][esp-idf:000][decoder]: I (38407) AUDIO_ELEMENT: [decoder] AEL_MSG_CMD_RESUME,state:1

[21:09:19][D][esp_aud:000]d]: 
ERROR Fatal error: protocol.data_received() call failed.
protocol: <aioesphomeapi._frame_helper.noise.APINoiseFrameHelper object at 0x7fa4dc080670>
transport: <_SelectorSocketTransport fd=6 read=polling write=<idle, bufsize=0>>
Traceback (most recent call last):
  File "/usr/lib/python3.11/asyncio/selector_events.py", line 1009, in _read_ready__data_received
    self._protocol.data_received(data)
  File "aioesphomeapi/_frame_helper/noise.py", line 136, in aioesphomeapi._frame_helper.noise.APINoiseFrameHelper.data_received
  File "aioesphomeapi/_frame_helper/noise.py", line 163, in aioesphomeapi._frame_helper.noise.APINoiseFrameHelper.data_received
  File "aioesphomeapi/_frame_helper/noise.py", line 319, in aioesphomeapi._frame_helper.noise.APINoiseFrameHelper._handle_frame
  File "/usr/local/lib/python3.11/dist-packages/noise/state.py", line 74, in decrypt_with_ad
    plaintext = self.cipher.decrypt(self.k, self.n, ad, ciphertext)
                ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
  File "/usr/local/lib/python3.11/dist-packages/noise/backends/default/ciphers.py", line 13, in decrypt
    return self.cipher.decrypt(nonce=self.format_nonce(n), data=ciphertext, associated_data=ad)
           ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
  File "src/chacha20poly1305_reuseable/__init__.py", line 127, in chacha20poly1305_reuseable.ChaCha20Poly1305Reusable.decrypt
  File "src/chacha20poly1305_reuseable/__init__.py", line 147, in chacha20poly1305_reuseable.ChaCha20Poly1305Reusable.decrypt
  File "src/chacha20poly1305_reuseable/__init__.py", line 263, in chacha20poly1305_reuseable._decrypt_with_fixed_nonce_len
  File "src/chacha20poly1305_reuseable/__init__.py", line 273, in chacha20poly1305_reuseable._decrypt_data
cryptography.exceptions.InvalidTag
WARNING test-01 @ 192.168.207.246: Connection error occurred: test-01 @ 192.168.207.246: Invalid encryption key: received_name=test-01
INFO Processing unexpected disconnect from ESPHome API for test-01 @ 192.168.207.246
WARNING Disconnected from API
INFO Successfully connected to test-01 @ 192.168.207.246 in 0.004s
INFO Successful handshake with test-01 @ 192.168.207.246 in 0.105s
[21:09:19][I][esp_adf_pipeline:214]: [ i2s_out ] status: 12
[21:09:19][D][esp_adf_pipeline:131]: Check element [http] status, 2
[21:09:19][I][esp_adf_pipeline:214]: [ resampler ] status: 12
[21:09:19][D][esp_adf_pipeline:131]: Check element [http] status, 2
[21:09:19][D][esp-idf:000][http]: I (38612) HTTP_CLIENT: Body received in fetch header state, 0x3fcc511b, 1841

[21:09:19][D][esp-idf:000][http]: I (38617) HTTP_STREAM: total_bytes=23199

[21:09:19][I][esp_adf_pipeline:214]: [ http ] status: 12
[21:09:19][D][esp_adf_pipeline:131]: Check element [http] status, 3
[21:09:19][D][esp_adf_pipeline:131]: Check element [decoder] status, 2
[21:09:19][I][esp_adf_pipeline:214]: [ decoder ] status: 12
[21:09:19][D][esp_adf_pipeline:131]: Check element [http] status, 3
[21:09:19][D][esp_adf_pipeline:131]: Check element [decoder] status, 3
[21:09:19][D][esp_adf_pipeline:131]: Check element [resampler] status, 3
[21:09:19][D][esp_adf_pipeline:131]: Check element [i2s_out] status, 3
[21:09:19][D][esp_adf_pipeline:302]: State changed from STARTING to RUNNING
[21:09:19][I][adf_media_player:135]: got new pipeline state: 3
[21:09:19][D][adf_i2s_out:127]: Set final i2s settings: 24000
[21:09:19][D][esp_audio_processors:079]: New settings: SRC: rate: 24000, ch: 1 DST: rate: 24000, ch: 1 
[21:09:19][I][HTTPStreamReader:129]: [ * ] Receive music info from mp3 decoder, sample_rates=24000, bits=16, ch=1
[21:09:19][D][adf_i2s_out:127]: Set final i2s settings: 24000
[21:09:19][D][esp_audio_processors:079]: New settings: SRC: rate: 24000, ch: 1 DST: rate: 24000, ch: 1 
[21:09:22][D][esp-idf:000][http]: W (41118) HTTP_STREAM: No more data,errno:0, total_bytes:23199, rlen = 0

[21:09:22][D][esp-idf:000][http]: I (41123) AUDIO_ELEMENT: IN-[http] AEL_IO_DONE,0

[21:09:22][I][esp_adf_pipeline:214]: [ http ] status: 15
[21:09:22][D][esp_adf_pipeline:302]: State changed from RUNNING to STOPPING
[21:09:22][I][adf_media_player:135]: got new pipeline state: 4
[21:09:22][D][esp-idf:000][decoder]: I (41799) AUDIO_ELEMENT: IN-[decoder] AEL_IO_DONE,-2

[21:09:23][D][esp-idf:000][decoder]: I (42161) MP3_DECODER: Closed

[21:09:23][D][esp-idf:000][resampler]: I (42267) AUDIO_ELEMENT: IN-[resampler] AEL_IO_DONE,-2

[21:09:23][D][esp-idf:000][i2s_out]: I (42330) AUDIO_ELEMENT: IN-[i2s_out] AEL_IO_DONE,-2

[21:09:23][D][esp_adf_pipeline:302]: State changed from STOPPING to STOPPED
[21:09:23][I][adf_media_player:135]: got new pipeline state: 5
[21:09:23][D][light:036]: 'test-01 Front LED' Setting:
[21:09:23][D][light:047]:   State: ON
[21:09:23][D][light:051]:   Brightness: 25%
[21:09:23][D][light:059]:   Red: 0%, Green: 0%, Blue: 100%
[21:09:23][D][micro_wake_word:177]: State changed from IDLE to START_MICROPHONE
[21:09:23][D][micro_wake_word:115]: Starting Microphone
[21:09:23][D][esp_adf_pipeline:050]: Starting request, current state STOPPED
[21:09:23][D][esp_adf_pipeline:302]: State changed from STOPPED to PREPARING
[21:09:23][D][micro_wake_word:177]: State changed from START_MICROPHONE to STARTING_MICROPHONE
[21:09:23][D][esp_adf_pipeline:302]: State changed from PREPARING to STARTING
[21:09:23][D][esp-idf:000]: I (42537) AUDIO_PIPELINE: Func:audio_pipeline_run, Line:359, MEM Total:8376627 Bytes, Inter:152808 Bytes, Dram:152808 Bytes


[21:09:23][D][esp-idf:000][i2s_in]: I (42539) AUDIO_ELEMENT: [i2s_in] AEL_MSG_CMD_RESUME,state:1

[21:09:23][D][esp-idf:000]: I (42543) AUDIO_PIPELINE: Pipeline started

[21:09:23][I][esp_adf_pipeline:214]: [ pcm_reader ] status: 14
[21:09:23][I][esp_adf_pipeline:214]: [ i2s_in ] status: 14
[21:09:23][I][esp_adf_pipeline:214]: [ i2s_in ] status: 12
[21:09:23][D][esp_adf_pipeline:131]: Check element [i2s_in] status, 3
[21:09:23][D][esp_adf_pipeline:131]: Check element [pcm_reader] status, 3
[21:09:23][D][esp_adf_pipeline:302]: State changed from STARTING to RUNNING
[21:09:23][D][micro_wake_word:177]: State changed from STARTING_MICROPHONE to DETECTING_WAKE_WORD
[21:09:23][I][esp_adf_pipeline:214]: [ pcm_reader ] status: 12
[21:09:25][D][micro_wake_word:362]: Wake word sliding average probability is 0.585 and most recent probability is 1.000
[21:09:25][D][micro_wake_word:128]: Wake Word Detected
[21:09:25][D][micro_wake_word:177]: State changed from DETECTING_WAKE_WORD to STOP_MICROPHONE
[21:09:25][D][micro_wake_word:134]: Stopping Microphone
[21:09:25][D][esp_adf_pipeline:302]: State changed from RUNNING to STOPPING
[21:09:25][D][micro_wake_word:177]: State changed from STOP_MICROPHONE to STOPPING_MICROPHONE
[21:09:25][D][esp-idf:000][i2s_in]: W (44496) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:25][D][esp-idf:000][i2s_in]: W (44499) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:25][D][esp-idf:000][i2s_in]: W (44503) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:25][D][esp-idf:000][i2s_in]: W (44506) AUDIO_ELEMENT: OUT-[i2s_in] AEL_IO_ABORT

[21:09:25][D][esp_adf_pipeline:302]: State changed from STOPPING to STOPPED
[21:09:25][D][micro_wake_word:177]: State changed from STOPPING_MICROPHONE to IDLE
[21:09:25][D][media_player:061]: 'media_player' - Setting
[21:09:25][D][media_player:065]:   Command: STOP
[21:09:25][D][esp_adf_pipeline:085]: Called 'stop' while in STOPPED state.
[21:09:25][D][light:036]: 'test-01 Front LED' Setting:
[21:09:25][D][light:051]:   Brightness: 75%
[21:09:25][D][light:059]:   Red: 0%, Green: 100%, Blue: 0%
[21:09:25][D][light:109]:   Effect: 'Pulse'

Does anyone know what's going on here?

try this:

external_components:
  - source:
      type: git
      url: https://github.com/gnumpi/esphome_audio
      ref: dev-next
    
    components: [ adf_pipeline, i2s_audio ]
    refresh: 0s

@HA-TB303
Copy link

That seems to have solved the issue. Thank you!

@AapoTahkola
Copy link

Regarding high pitch sounds during playback clicks are typically caused by signal integrity issues since these are relatively high speed signals. Especially if the distortion stops if you touch the high speed lines with your hand, move things. You should be able to so solve such issues by using better quality dupont lines with higher load spring mechanisms, soldering the dupont lines without the plastic cases, twisting the high speed lines together with gnd or even adding some grounded tinfoil around the signal wires. Another thing I noticed the INMP441 can pick up alot of noise if the PCB touches a surface that is vibrating. A good solution probably is to use some polyester fiber like in pillows to make sure the MEMS microphone does touch any hard surfaces in casing that you have.

Longer pauses like over 300ms are most likely caused by buffering issues, which is another story altogether.

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment