gistfile1.txt

[  216.288532] [VFE]cci probe start cci_sel = 0!
[  216.288675] [VFE]cci probe end cci_sel = 0!
[  216.288987] [VFE]cci_init end
[  305.485024] [VFE]Welcome to Video Front End driver
[  305.485366] [VFE]pdev->id = 0
[  305.485375] [VFE]dev->mipi_sel = 0
[  305.485383] [VFE]dev->vip_sel = 0
[  305.485391] [VFE]dev->isp_sel = 0
[  305.491515] [VFE_WARN]vfe vpu clock is null
[  305.499107] [VFE]..........................vfe clk open!.......................
[  305.499141] [ISP] isp platform_id = 5!
[  305.499292] [VFE]vfe_init end
[  305.500111] [VFE]probe_work_handle start!
[  305.500137] [VFE]v4l2 subdev register input_num = 0
[  305.500154] [VFE]vfe sensor detect start! input_num = 0
[  305.500167] [VFE_WARN]Camer detect "YUV" fmt is different from sys_config!
[  305.500179] [VFE_WARN]Apply detect  fmt = 0 replace sys_config fmt = 1!
[  305.500191] [VFE]Find sensor name is "ov5640", i2c address is 78, type is "YUV" !
[  305.500204] [VFE]Sub device register "ov5640" i2c_addr = 0x78 start!
[  305.500221] [VFE]v4l2_device_register_subdev return 0
[  305.500232] [VFE]registered sensor subdev is OK!
[  305.500240] [VFE]Check sensor!
[  305.513563] [VFE]mclk on
[  305.580334] [VFE CCI_0 ERR] Status error at addr_8bit = 78, wr_flag = 1, val = 1000a30
[  305.580595] [VFE CCI_0 ERR] Status error at addr_8bit = 78, wr_flag = 1, val = 1000a30
[  305.580852] [VFE CCI_0 ERR] Status error at addr_8bit = 78, wr_flag = 1, val = 1000a30
[  305.580869] [OV5640]error at sensor_detect
[  305.580878] [OV5640]chip found is not an target chip.
[  305.580888] [VFE]mclk off
[  305.617004] [VFE]vfe sensor subdev unregister!
[  305.617019] [VFE]Sub device register "ov5640" failed!
[  305.617029] [VFE_ERR]vfe sensor register check error at input_num = 0
[  305.621776] [VFE]V4L2 device registered as video0
[  305.621811] [VFE]..........................vfe clk close!.......................
[  305.621833] [VFE]probe_work_handle end!
[  305.626876] [VFE]vfe_open
[  305.626896] [VFE]..........................vfe clk open!.......................
[  305.626935] [VFE]vfe_open ok
[  305.627137] [VFE]vfe_close
[  305.627150] [VFE]vfe select input flag = 0, s_input have not be used .
[  305.627167] [VFE]..........................vfe clk close!.......................
[  305.627196] [VFE]vfe_close end