default.txt

[    0.000000] Linux version 5.10.70 (peter@plato) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r17565-93f488fc37) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 Mon Oct 11 19:29:33 2021
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] MIPS: machine is TP-Link Archer C7 v5
[    0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] On node 0 totalpages: 32768
[    0.000000]   Normal zone: 288 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 120960K/131072K available (5550K kernel code, 595K rwdata, 1224K rodata, 1196K init, 201K bss, 10112K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] random: get_random_bytes called from start_kernel+0x3c0/0x5b0 with crng_init=0
[    0.000000] CPU clock: 775.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[    0.000007] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[    0.008215] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.074751] pid_max: default: 32768 minimum: 301
[    0.079746] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.087461] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.097313] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.108313] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.118716] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.125979] pinctrl core: initialized pinctrl subsystem
[    0.132410] NET: Registered protocol family 16
[    0.189583] clocksource: Switched to clocksource MIPS
[    0.195995] NET: Registered protocol family 2
[    0.200784] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.208879] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.217791] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.225889] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.233335] TCP: Hash tables configured (established 1024 bind 1024)
[    0.240157] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.247057] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.254702] NET: Registered protocol family 1
[    0.259324] PCI: CLS 0 bytes, default 32
[    0.268904] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.279220] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.285425] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.299171] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[    0.305742] gpio-export gpio-export: 1 gpio(s) exported
[    0.312070] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.319393] printk: console [ttyS0] disabled
[    0.324008] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A
[    0.333121] printk: console [ttyS0] enabled
[    0.342179] printk: bootconsole [early0] disabled
[    0.362796] spi-nor spi0.0: w25q128 (16384 Kbytes)
[    0.367818] 8 fixed-partitions partitions found on MTD device spi0.0
[    0.374437] Creating 8 MTD partitions on "spi0.0":
[    0.379387] 0x000000000000-0x000000020000 : "factory-uboot"
[    0.388578] 0x000000020000-0x000000040000 : "u-boot"
[    0.394582] 0x000000040000-0x000000050000 : "partition-table"
[    0.402869] 0x000000050000-0x000000060000 : "art"
[    0.408558] 0x000000060000-0x000000080000 : "info"
[    0.415818] 0x000000080000-0x0000000c0000 : "user-config"
[    0.422351] 0x0000000c0000-0x000000fc0000 : "firmware"
[    0.430103] 2 uimage-fw partitions found on MTD device firmware
[    0.436223] Creating 2 MTD partitions on "firmware":
[    0.441405] 0x000000000000-0x0000002295b1 : "kernel"
[    0.446526] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only
[    0.456581] 0x0000002295b1-0x000000f00000 : "rootfs"
[    0.461759] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only
[    0.472076] mtd: device 8 (rootfs) set to be root filesystem
[    0.478756] 1 squashfs-split partitions found on MTD device rootfs
[    0.485195] 0x0000005b0000-0x000000f00000 : "rootfs_data"
[    0.491578] 0x000000ff0000-0x000001000000 : "default-config"
[    0.505423] libphy: Fixed MDIO Bus: probed
[    1.220255] libphy: ag71xx_mdio: probed
[    1.228445] ag71xx 19000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[    1.238289] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: mii
[    1.244771] i2c /dev entries driver
[    1.250897] NET: Registered protocol family 10
[    1.264121] Segment Routing with IPv6
[    1.268005] NET: Registered protocol family 17
[    1.272994] 8021q: 802.1Q VLAN Support v1.8
[    1.278023] PCI host bridge /ahb/pcie-controller@18250000 ranges:
[    1.284394]  MEM 0x0000000012000000..0x0000000013ffffff
[    1.289808]   IO 0x0000000000000000..0x0000000000000000
[    1.295375] PCI host bridge to bus 0000:00
[    1.299651] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[    1.306751] pci_bus 0000:00: root bus resource [io  0x0000]
[    1.312517] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    1.319527] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.327761] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000
[    1.334011] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    1.341080] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    1.348071] pci 0000:00:00.0: supports D1 D2
[    1.353745] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    1.360639] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[    1.368210] pci 0000:00:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[    1.379190] libphy: qca8k slave mii: probed
[    1.456688] qca8k mdio.0:00: configuring for fixed/sgmii link mode
[    1.467385] qca8k mdio.0:00: Link is Up - 1Gbps/Full - flow control off
[    1.544435] qca8k mdio.0:00 wan (uninitialized): PHY [qca8k-0:00] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[    1.634444] qca8k mdio.0:00 lan1 (uninitialized): PHY [qca8k-0:01] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[    1.724465] qca8k mdio.0:00 lan2 (uninitialized): PHY [qca8k-0:02] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[    1.814452] qca8k mdio.0:00 lan3 (uninitialized): PHY [qca8k-0:03] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[    1.904445] qca8k mdio.0:00 lan4 (uninitialized): PHY [qca8k-0:04] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[    1.921348] DSA: tree 0 setup
[    1.933107] VFS: Mounted root (squashfs filesystem) readonly on device 31:8.
[    1.946965] Freeing unused kernel memory: 1196K
[    1.951688] This architecture does not have kernel memory protection.
[    1.958348] Run /sbin/init as init process
[    1.962584]   with arguments:
[    1.962589]     /sbin/init
[    1.962592]   with environment:
[    1.962596]     HOME=/
[    1.962599]     TERM=linux
[    2.299594] random: fast init done
[    2.559625] init: Console is alive
[    2.563625] init: - watchdog -
[    3.792551] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.840235] usbcore: registered new interface driver usbfs
[    3.845958] usbcore: registered new interface driver hub
[    3.851589] usbcore: registered new device driver usb
[    3.868990] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.886884] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.904846] init: - preinit -
[    5.464149] random: jshn: uninitialized urandom read (4 bytes read)
[    5.589356] random: jshn: uninitialized urandom read (4 bytes read)
[    5.716352] random: jshn: uninitialized urandom read (4 bytes read)
[    6.025690] eth0: link up (1000Mbps/Full duplex)
[    6.030769] qca8k mdio.0:00 lan1: configuring for phy/internal link mode
[    6.037794] 8021q: adding VLAN 0 to HW filter on device lan1
[    6.043820] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   10.390088] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[   10.397586] jffs2_build_filesystem(): unlocking the mtd device... 
[   10.397589] done.
[   10.405968] jffs2_build_filesystem(): erasing all blocks after the end marker... 
[   49.250560] done.
[   49.260330] jffs2: notice: (534) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   49.277716] mount_root: overlay filesystem has not been fully initialized yet
[   49.290067] mount_root: switching to jffs2 overlay
[   49.297553] overlayfs: upper fs does not support tmpfile.
[   49.835820] urandom-seed: Seed file not found (/etc/urandom.seed)
[   50.082777] procd: - early -
[   50.086079] procd: - watchdog -
[   50.687818] procd: - watchdog -
[   50.691516] procd: - ubus -
[   50.785883] urandom_read: 5 callbacks suppressed
[   50.785891] random: ubusd: uninitialized urandom read (4 bytes read)
[   50.799889] random: ubusd: uninitialized urandom read (4 bytes read)
[   50.813159] procd: - init -
[   51.927581] kmodloader: loading kernel modules from /etc/modules.d/*
[   52.320032] urngd: v1.0.2 started.
[   52.456230] Loading modules backported from Linux version v5.10.68-0-g4d8524048a35
[   52.464099] Backport generated by backports.git v5.10.68-1-0-ga4f9ba32
[   52.518018] random: crng init done
[   52.540566] xt_time: kernel timezone is -0000
[   52.871630] PPP generic driver version 2.4.2
[   52.890676] NET: Registered protocol family 24
[   52.976399] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x3c.
[   53.000958] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[   53.009732] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[   56.883325] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[   56.892889] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   56.904829] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-8x-__fW-022-ecad3248 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 3e4cf97f
[   57.431468] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   58.416898] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
[   58.434334] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[   58.440812] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
[   58.449082] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 24984 iram: 38672'
[   58.502987] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[   58.517215] ath10k_pci 0000:00:00.0: NOTE:  Firmware DBGLOG output disabled in debug_mask: 0x10000000
[   58.653203] ath: EEPROM regdomain sanitized
[   58.653216] ath: EEPROM regdomain: 0x64
[   58.653221] ath: EEPROM indicates we should expect a direct regpair map
[   58.653241] ath: Country alpha2 being used: 00
[   58.653245] ath: Regpair used: 0x64
[   58.746407] ath: EEPROM regdomain sanitized
[   58.746422] ath: EEPROM regdomain: 0x64
[   58.746426] ath: EEPROM indicates we should expect a direct regpair map
[   58.746447] ath: Country alpha2 being used: 00
[   58.746451] ath: Regpair used: 0x64
[   58.758100] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[   58.760024] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=2
[   58.794890] kmodloader: done loading kernel modules from /etc/modules.d/*
[   75.296340] eth0: link down
[   75.426441] eth0: link up (1000Mbps/Full duplex)
[   75.446227] br-lan: port 1(eth0.1) entered blocking state
[   75.451870] br-lan: port 1(eth0.1) entered disabled state
[   75.457719] device eth0.1 entered promiscuous mode
[   75.462715] device eth0 entered promiscuous mode
[   75.471587] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   75.503693] br-lan: port 1(eth0.1) entered blocking state
[   75.509288] br-lan: port 1(eth0.1) entered forwarding state
[   78.256157] netlink: 'iw': attribute type 302 has an invalid length.
[   79.738461] br-lan: port 2(wlan1) entered blocking state
[   79.744007] br-lan: port 2(wlan1) entered disabled state
[   79.749824] device wlan1 entered promiscuous mode
[   79.944074] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   79.950921] br-lan: port 2(wlan1) entered blocking state
[   79.956412] br-lan: port 2(wlan1) entered forwarding state