Skip to content

Instantly share code, notes, and snippets.

@Icenowy

Icenowy/gist:7bcf34f64d71c71c9e64055dde89653e

Created November 23, 2017 04:09
Show Gist options
  • Star 0 You must be signed in to star a gist
  • Fork 0 You must be signed in to fork a gist
  • Save Icenowy/7bcf34f64d71c71c9e64055dde89653e to your computer and use it in GitHub Desktop.
Save Icenowy/7bcf34f64d71c71c9e64055dde89653e to your computer and use it in GitHub Desktop.
Download ZIP
H6 boot log
Raw
gistfile1.txt
[85]HELLO! BOOT0 is starting!
[89]boot0 commit : 62ee2c78daf826c2a0bfd1f818e301853b94f5cd
[107]PMU: AXP806
[111]set pll start
[114]set pll end
[116]rtc[0] value = 0x00000000
[119]rtc[1] value = 0x00000000
[122]rtc[2] value = 0x00000000
[125]rtc[3] value = 0x0000b00f
[128]rtc[4] value = 0x00000000
[131]rtc[5] value = 0x00000000
[134]DRAM VERSION IS V2_2
[137]PMU:Set DDR Vol 1200mV OK.
[140]PMU:Set DDR Vol 1200mV OK.
[147]DRAM CLK =744 MHZ
[149]DRAM Type =7 (3:DDR3,4:DDR4,6:LPDDR2,7:LPDDR3)
[154]DRAM zq value: 003b3bfb
[158]IPRD=00640063--PGCR0=00000f5d--PLL=b0003d00
[163]DRAM SIZE =2048 M
[171]DRAM simple test OK.
[174]dram size =2048
[177]card no is 0
[178]sdcard 0 line count 4
[181][mmc]: mmc driver ver 2017-03-14 13:56
[185][mmc]: sdc0 spd mode error, 2
[189][mmc]: mmc 0 bias 00000000
[197][mmc]: Wrong media type 0x00000000
[201][mmc]: ***Try SD card 0***
[211][mmc]: HSSDR52/SDR25 4 bit
[214][mmc]: 50000000 Hz
[217][mmc]: 7464 MB
[219][mmc]: ***SD/MMC 0 init OK!!!***
[360]Loading boot-pkg Succeed(index=0).
[364]Entry_name = u-boot
[379]Entry_name = parameter
[382]Entry_name = monitor
[386]Entry_name = scp
[395]set arisc reset to de-assert state
[399]Entry_name = soc-cfg
[403]Entry_name = dtb
[406]Entry_name = board-cfg
[410]Entry_name = board-fex
[413]Entry_name = esm-img
[418]Entry_name = logo
[421]Ready to disable icache.
INFO: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):7408d88
NOTICE: BL3-1: Built : 20:42:28, Aug 29 2017
NOTICE: BL3-1 commit: 7408d88f80cb14038350a8f55a280fd0c4caf626
INFO: BL3-1: Initializing runtime services
ERROR: Error initializing runtime service tspd_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x4a000000
INFO: BL3-1: Next image spsr = 0x1d3
U-Boot 2014.07 (Sep 05 2017 - 15:29:29) Allwinner Technology
uboot commit : 372f88f75c049d92bb0adef5204013659ea8441f
secure enable bit: 0
normal mode: with secure monitor
I2C: ready
[0.471]pmbus: ready
u0:2be2820d
[0.472][ARISC] :arisc initialize
[0.496][ARISC] :arisc para ok
[SCP] :sunxi-arisc driver begin startup 2
[SCP] :arisc version: [v0.2.30]
[SCP] :sunxi-arisc driver v1.10 is starting
[0.510][ARISC] :sunxi-arisc driver startup succeeded
[0.511]PMU: AXP806
[0.511]PMU: AXP806 found
[0.511]bat_vol=0, ratio=0
axp=axp806, supply=bldo2, vol=1800
axp=, supply=, vol=0
[0.516]set power on vol to default
[0.516]dcdca_vol = 1000, onoff=1
[0.520]aldo2_vol = 3300, onoff=1
[0.524]find power_sply to end
[0.524]PMU: cpux 1320 Mhz,AXI=440 Mhz
PLL6=600 Mhz,AHB1=200 Mhz, APB1=150Mhz MBus=400Mhz
DRAM: 2 GiB
[0.526]fdt addr: 0xb6ccf220
[0.528]gd->fdt_size: 0x18620
Relocation Offset is: 75d90000
gic: sec monitor mode
[box standby] read rtc = 0x0
[box standby] start_type = 0x1
[box standby] to kernel
ir boot recovery not used
[0.619][key recovery] no key press.
[0.619]power on cpu1
[0.619][cpu1]task entry
[0.619][cpu1]PowerBus = 0( 2:vBus 3:acBus other: not exist)
[0.619][cpu1]no battery exist
[0.619]start
[cpu1]drv_disp_init
[cpu1]init_clocks: finish init_clocks.
[0.627][cpu1]HDMI 2.0 driver init start!
[0.629]power on cpu2
workmode = 0,storage type = 1
[0.629]MMC: 0
[0.629][mmc]: mmc driver ver 2017-09-4 10:12:00
[0.629][cpu2]task entry
[cpu1]__clk_enable: clk is null.
[0.634][cpu2]ready to work
[0.637][cpu1]hdmi cec clk enable failed!
SUNXI SD/MMC: 0[0.643][cpu1]enable ddc_scl pin
[0.647][cpu1]enable ddc_sda pin
[0.650][cpu1]enable hmid cec pin
[0.653][mmc]: media type 0x0
[cpu1]pwm_request: reg = 0x300a000. pwm = 1.
[0.656][mmc]: Wrong media type 0x0
[cpu1]request pwm success, pwm = 1.
[0.663][mmc]: ************Try SD card 0************
[0.658][cpu2]cpu 2 enter wfi mode
[cpu1]speed=200000, slave=16
[0.677][mmc]: host caps: 0x27
[0.679][mmc]: MID 12 PSN 000026c5
[0.682][mmc]: PNM ASTC -- 0x41-53-54-43-00
[0.686][mmc]: PRV 3.4
[0.688][mmc]: MDT m-4 y-2017
[0.691][mmc]: bus_width : 4 bit
[0.694][mmc]: user capacity : 7464 MB
[0.697][mmc]: SD/MMC 0 init OK!!!
[0.701][mmc]: End mmc_init_boot
[0.703]sunxi flash init ok
used mbr [0], count = 5
[0.708]try to burn key
--------fastboot partitions--------
-total partitions:5-
-name- -start- -size-
bootloader : 1000000 1000000
env : 2000000 1000000
boot : 3000000 1000000
rootfs : 4000000 20000000
UDISK : 24000000 0
-----------------------------------
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_mmc
no misc partition is found
[0.748]to be run cmd=run setargs_mmc boot_normal
mac string is 00:00:00:00:00:00
read item0 copy0
Item0 (Map) magic is bad
the secure storage item0 copy0 is bad
read item0 copy1
Item0 (Map) magic is bad
the secure storage item0 copy0 == copy1, the data is good
the secure storage map is empty
check user data form private
the private part isn't exist
dragonboard_handler call
[0.782]NAND_UbootProbe start
[0.785]NB1 : enter phy init
[0.787]nand_physic_init
[0.793]uboot Nand0 clk: 20MHz,PERI=1200,N=4,M=15,T=10
[0.794]uboot Nand Ecc clk: 20MHz,PERI=1200,N=4,M=15,T=20
[0.799]uboot Nand0 clk: 40MHz,PERI=1200,N=2,M=15,T=20
[0.804]uboot Nand Ecc clk: 40MHz,PERI=1200,N=2,M=15,T=40
[0.809]Reset NDFC start 0 0
[0.811]Reset NDFC end 0 0
[0.814]nand not support! channel 0 chip 0: 00 00 00 00 00 00 00 00
[0.820]nand not support! channel 0 chip 1: 00 00 00 00 00 00 00 00
[0.826]nand not support! channel 0 chip 2: 00 00 00 00 00 00 00 00
[0.832]nand not support! channel 0 chip 3: 00 00 00 00 00 00 00 00
[0.837] no nand found !
[0.840]nand_physic_init nand_build_nsi error
[0.844]nand_physic_init error -1
[0.847]NB1 : nand phy init fail
[0.849]NB1 : enter phy Exit
[0.852]nand_physic_exit
[0.854]NAND_UbootProbe end: 0xffffffff
try to find card2
[0.859][mmc]: mmc driver ver 2017-09-4 10:12:00
[0.865][mmc]: get sdc_ex_dly_used 2, use auto tuning sdly
[0.869][mmc]: get sdly from uboot header fail
[0.873][mmc]: card2 io is 1.8V.
[0.876][mmc]: get sdc2 sdc_tm4_hs200_max_freq 150.
[0.880][mmc]: get sdc2 sdc_tm4_hs400_max_freq 100.
[cpu1]drv_disp_init finish
SUNXI SD/MMC: 0[cpu1]hdmi hdcp not enable!
, SUNXI SD/MMC: 2
[cpu1]hdmi hpd out, force open?
[cpu1]save_int_to_kernel disp.init_disp(0x20b040a) code:<no error>
[0.898][mmc]: media type 0x0
[cpu1]invalid display config
[0.904][mmc]: Wrong media type 0x0
[cpu1]save disp device failed
[0.910][mmc]: ************Try SD card 2************
[cpu1]size=0x384000, ram_size=0x80000000, FRAME_BUFFER_SIZE=0x1000000
[mmc]: mmc 2 cmd 8 timeout, err 100
[0.923]end
[mmc]: smc 2 err, cmd 8, RTO
[cpu1]advert_enable not set
[mmc]: mmc 2 close bus gating and reset
[cpu1]save_string_to_kernel disp.boot_fb0(bf000000,500,2d0,20,1400,0,0,500,2d0). ret-code:<no error>
[mmc]: mmc 2 mmc cmd 8 err 0x00000100
[0.945][cpu1]boot logo from boot_package/toc1 item display ok
[0.948][mmc]: mmc send if cond failed
[mmc]: mmc 2 cmd 55 timeout, err 100
[mmc]: smc 2 err, cmd 55, RTO
[mmc]: mmc 2 close bus gating and reset
[mmc]: mmc 2 mmc cmd 55 err 0x00000100
[0.970][mmc]: send app cmd failed
[0.973][mmc]: ************Try MMC card 2************
[mmc]: mmc 2 cmd 1 timeout, err 100
[mmc]: smc 2 err, cmd 1, RTO
[mmc]: mmc 2 close bus gating and reset
[mmc]: mmc 2 mmc cmd 1 err 0x00000100
[0.991][mmc]: read op condition failed
[0.994][mmc]: mmc send op cond failed
Card did not respond to voltage select!
[1.001][mmc]: ************SD/MMC 2 init error!!!************
[1.004][cpu1]cpu 1 enter wfi mode
[1.006][mmc]: mmc_init_boot: mmc int fail
[1.013][mmc]: mmc_init: mmc init fail, err -17
try card2 successed
[1.019][mmc]: mmc exit start
[mmc]: mmc 2 cmd 1 timeout, err 100
[mmc]: smc 2 err, cmd 1, RTO
[mmc]: mmc 2 close bus gating and reset
[mmc]: mmc 2 mmc cmd 1 err 0x00000100
[1.035][mmc]: read op condition failed
[1.038][mmc]: mmc send op cond failed
[mmc]: mmc 2 cmd 1 timeout, err 100
[mmc]: smc 2 err, cmd 1, RTO
[mmc]: mmc 2 close bus gating and reset
[mmc]: mmc 2 mmc cmd 1 err 0x00000100
[1.054][mmc]: read op condition failed
[1.058][mmc]: mmc send op cond failed
[1.061][mmc]: mmc card did not respond to voltage select!
[1.066][mmc]: mmc 2 exit failed
[1.071][mmc]: delete mmc-hs400-1_8v from dtb
[1.073][mmc]: delete mmc-hs200-1_8v from dtb
[1.077][mmc]: delete mmc-ddr-1_8v from dtb
[1.081][mmc]: delete max-frequency from dtb
[1.085]update dtb dram start
[1.088]update dtb dram end
serial is: dc000141091d1c2e024b
Net: phy_mode=rmii, phy_interface=5
eth0
Warning: failed to set MAC address
[1.102]inter uboot shell
Hit any key to stop autoboot: 0
[1.105]read partition: boot or recovery
[1.845]sunxi flash read :offset 3000000, 17646827 bytes OK
Android's image name: sun50i_arm64
Kernel load addr 0x40080000 size 13506 KiB
RAM disk load addr 0x41000000 size 2704 KiB
[1.859]ready to boot
[1.859]check cpu power status
[1.859]cpu2 has poweroff
[1.859]cpu1 has poweroff
[1.861]prepare for kernel
[1.861]check cpu power status
[1.861]cpu2 has poweroff
[1.861]cpu1 has poweroff
[1.861][mmc]: mmc exit start
[mmc]: mmc 2 cmd 1 timeout, err 100
[mmc]: smc 2 err, cmd 1, RTO
[mmc]: mmc 2 close bus gating and reset
[mmc]: mmc 2 mmc cmd 1 err 0x00000100
[1.873][mmc]: read op condition failed
[1.876][mmc]: mmc send op cond failed
[mmc]: mmc 2 cmd 1 timeout, err 100
[mmc]: smc 2 err, cmd 1, RTO
[mmc]: mmc 2 close bus gating and reset
[mmc]: mmc 2 mmc cmd 1 err 0x00000100
[1.892][mmc]: read op condition failed
[1.896][mmc]: mmc send op cond failed
[1.899][mmc]: mmc card did not respond to voltage select!
[1.904][mmc]: mmc 2 exit failed
[1.907]
Starting kernel ...
INFO: BL3-1: Next image address = 0x40080000
INFO: BL3-1: Next image spsr = 0x3c5
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.65 (icenowy@x220i) (gcc version 4.9.3 20150113 (prerelease) (Linaro GCC 4.9-2015.01-3) ) #2 SMP PREEMPT Wed Nov 22 12:56:55 CST 2017
[ 0.000000] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000] Machine: sun50iw6
[ 0.000000] cma: CMA: reserved 16 MiB at bf000000
[ 0.000000] On node 0 totalpages: 524288
[ 0.000000] DMA zone: 7168 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 524288 pages, LIFO batch:31
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv0.2 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] PERCPU: Embedded 12 pages/cpu @ffffffc07ef80000 s20224 r8192 d20736 u49152
[ 0.000000] pcpu-alloc: s20224 r8192 d20736 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 517120
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p7 init=/init loglevel=8 partitions=bootloader@mmcblk0p2:env@mmcblk0p5:boot@mmcblk0p6:rootfs@mmcblk0p7:UDISK@mmcblk0p1
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Memory: 2048MB = 2048MB total
[ 0.000000] Memory: 2014548k/2014548k available, 82604k reserved
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbbffff0000 (245759 MB)
[ 0.000000] vmemmap : 0xffffffbc00e00000 - 0xffffffbc02a00000 ( 28 MB)
[ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc080000000 ( 2048 MB)
[ 0.000000] .init : 0xffffffc000b6f000 - 0xffffffc000bfcf00 ( 568 kB)
[ 0.000000] .text : 0xffffffc000080000 - 0xffffffc000b6e884 ( 11195 kB)
[ 0.000000] .data : 0xffffffc000bfd000 - 0xffffffc000db0538 ( 1742 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (virt).
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] allocated 8388608 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.010000] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.010000] pid_max: default: 32768 minimum: 301
[ 0.010000] Security Framework initialized
[ 0.010000] SELinux: Initializing.
[ 0.010000] SELinux: Starting in permissive mode
[ 0.010000] Mount-cache hash table entries: 256
[ 0.010000] Initializing cgroup subsys debug
[ 0.010000] Initializing cgroup subsys memory
[ 0.010000] Initializing cgroup subsys freezer
[ 0.010000] ftrace: allocating 30105 entries in 118 pages
[ 0.020594] CPU0: update cpu_power 1024
[ 0.020610] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 0.021406] virtual base = 0xffffff800000a000.
[ 0.021414] gicd_base = 0xffffff800000c000.
[ 0.021418] gicc_base = 0xffffff800000e000.
[ 0.021671] CPU1: Booted secondary processor
[ 0.021671] CPU1: update cpu_power 1024
[ 0.021714] CPU2: Booted secondary processor
[ 0.021714] CPU2: update cpu_power 1024
[ 0.021714] CPU3: Booted secondary processor
[ 0.021714] CPU3: update cpu_power 1024
[ 0.021714] Brought up 4 CPUs
[ 0.021714] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[ 0.021714] devtmpfs: initialized
[ 0.023157] atomic64 test passed
[ 0.023157] pinctrl core: initialized pinctrl subsystem
[ 0.023157] NET: Registered protocol family 16
[ 0.023157] dump_class_init,844, success
[ 0.030151] vdso: 2 pages (1 code, 1 data) at base ffffffc000c05000
[ 0.030170] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.031122] software IO TLB [mem 0xbb800000-0xbbc00000] (4MB) mapped at [ffffffc07b800000-ffffffc07bbfffff]
[ 0.031869] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.031921] pll_periph0-set_default_rate=600000000 success!
[ 0.031921] pll_periph1-set_default_rate=600000000 success!
[ 0.031921] pll_video1-set_default_rate=594000000 success!
[ 0.031921] pll_de-set_default_rate=696000000 success!
[ 0.031921] de-set_default_source=pll_de success!
[ 0.031921] de-set_default_rate=696000000 success!
[ 0.031921] clk sata not found in of_sunxi_periph_clk_setup
[ 0.031921] clk sata_24m not found in of_sunxi_periph_clk_setup
[ 0.031921] pciemaxi-set_default_rate=200000000 success!
[ 0.031921] pcieaux-set_default_rate=1000000 success!
[ 0.031921] hdmi-set_default_source=pll_video1 success!
[ 0.031921] tcon_tv-set_default_source=pll_video1 success!
[ 0.031988] hdmi_hdcp-set_default_source=pll_periph1 success!
[ 0.033270] sun50iw6p1-r-pinctrl r_pio: initialized sunXi PIO driver
[ 0.033270] sun50iw6p1-pinctrl pio: initialized sunXi PIO driver
[ 0.033270] sunxi hwspinlock vbase:0xffffff800005e000
[ 0.050196] [ARISC] :sunxi-arisc driver v1.60
[ 0.050744] [ARISC] :sunxi-arisc driver v1.60 startup succeeded
[ 0.070167] bio: create slab <bio-0> at 0
[ 0.070319] pwm module init!
[ 0.070665] SCSI subsystem initialized
[ 0.070665] usbcore: registered new interface driver usbfs
[ 0.070665] usbcore: registered new interface driver hub
[ 0.070665] usbcore: registered new device driver usb
[ 0.080348] Linux video capture interface: v2.00
[ 0.080348] [axp806] chip id detect 0x60 !
[ 0.132048] drm config service not available: FFFFFFFF
[ 0.132048] irq = 89
[ 0.132048] Attached to iommu domain
[ 0.132048] Attached to iommu domain
[ 0.132048] Attached to iommu domain
[ 0.132048] Attached to iommu domain
[ 0.132048] Attached to iommu domain
[ 0.132048] Attached to iommu domain
[ 0.132048] Attached to iommu domain
[ 0.132048] Attached to iommu domain
[ 0.132048] Attached to iommu domain
[ 0.132048] Advanced Linux Sound Architecture Driver Initialized.
[ 0.132048] Bluetooth: Core ver 2.16
[ 0.132048] NET: Registered protocol family 31
[ 0.132048] Bluetooth: HCI device and connection manager initialized
[ 0.132048] Bluetooth: HCI socket layer initialized
[ 0.132048] Bluetooth: L2CAP socket layer initialized
[ 0.132048] Bluetooth: SCO socket layer initialized
[ 0.132048] cfg80211: Calling CRDA to update world regulatory domain
[ 0.140143] [DISP]disp_module_init
[ 0.140634] [DISP] init_disp:0x20b040a
[ 0.140641] [DISP] boot_disp:0x0
[ 0.142258] [DISP] fb_base:0x0
[ 0.150308] [DISP]disp_module_init finish
[ 0.150691] acx00_detect, l:382, twi_id:3, adapter->nr:3
[ 0.150691] acx00_i2c_probe,l:264
[ 0.150691] acx00_init_work,l:127
[ 0.150975] __sid_efuse_key_is_readable()609 - The key oem write protect bit not burned!
[ 0.151520] sunxi budget cooling probe start !
[ 0.151520] CPU freq cooling register Success
[ 0.151520] CPU hotplug cooling register Success
[ 0.151520] CPU budget cooling register Success
[ 0.151520] __sid_efuse_key_is_readable()609 - The key thermal_sensor write protect bit not burned!
[ 0.151520] Switching to clocksource arch_sys_counter
[ 0.164384] FS-Cache: Loaded
[ 0.164765] CacheFiles: Loaded
[ 0.174444] get det_vbus is fail, 84
[ 0.175623] [ddrfreq] disabled, but continue to get freq!
[ 0.175857] devfreq dramfreq: Couldn't update frequency transition information.
[ 0.175885] sunxi_dramfreq_irq_mask_control: the key master doesn't exit
[ 0.176068] NET: Registered protocol family 2
[ 0.176547] TCP established hash table entries: 16384 (order: 6, 262144 bytes)
[ 0.176759] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 0.176985] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.177045] TCP: reno registered
[ 0.177054] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.177093] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.177324] NET: Registered protocol family 1
[ 0.177546] RPC: Registered named UNIX socket transport module.
[ 0.177551] RPC: Registered udp transport module.
[ 0.177556] RPC: Registered tcp transport module.
[ 0.177560] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.177726] Unpacking initramfs...
[ 0.280720] acx00_init_work,l:134
[ 0.301742] Freeing initrd memory: 2700K (ffffffc001000000 - ffffffc0012a3000)
[ 0.302176] hw perfevents: Failed to parse /pmu/interrupt-affinity[0]
[ 0.303332] lock super standby defaultly!
[ 0.303343] lookup_scene_lock_name: new scene lock super_standby
[ 0.303348] scene_lock_init name=super_standby
[ 0.303354] scene_lock: super_standby, type 5, count 1
[ 0.303951] audit: initializing netlink socket (disabled)
[ 0.303986] type=2000 audit(0.300:1): initialized
[ 0.312663] FS-Cache: Netfs 'nfs' registered for caching
[ 0.313330] FS-Cache: Netfs 'cifs' registered for caching
[ 0.313583] NTFS driver 2.1.30 [Flags: R/W].
[ 0.313813] fuse init (API version 7.22)
[ 0.314543] msgmni has been set to 3971
[ 0.314574] SELinux: Registering netfilter hooks
[ 0.315613] io scheduler noop registered
[ 0.315620] io scheduler deadline registered
[ 0.315770] io scheduler cfq registered (default)
[ 0.316320] [pm]aw_pm_init!
[ 0.316436] np name = /soc@03000000/rtc@07000000.
[ 0.316442] base = ffffff8001f42100, len = 8.
[ 0.316447] pmu name: pmic0 .
[ 0.316530] Warning: can not find np for pmic0.
[ 0.316535] pmu name: pmic1 .
[ 0.316557] Warning: can not find np for pmic1.
[ 0.319607] add_sys_pwr_dm: get ldo name for id: vdd-cpus failed
[ 0.319615] add_sys_pwr_dm: get ldo name for id: vcc-lpddr failed
[ 0.320716] add_sys_pwr_dm: axp80_cldo1 ldo already alwayson.
[ 0.320724] add_sys_pwr_dm: get ldo name for id: vcc-ldoin failed
[ 0.321735] add_sys_pwr_dm: get ldo name for id: vcc-pc failed
[ 0.321739] after inited: sys_mask config = 0x4a15.
[ 0.321763] Warning: can not find np for dynamic_standby_para.
[ 0.321916] [pm]valid
[ 0.321920] [pm]valid
[ 0.321924] Notice: sun9i & sun8iw5 & sun50i not need support normal standby, change to super standby.
[ 0.322314] sunxi_bootup_extend_probe: bootup extend state 1
[ 0.322319] bootup extend probe ok
[ 0.322695] gpio_pin_1(359) gpio_is_valid
[ 0.322847] gpio_pin_2(355) gpio_is_valid
[ 0.322960] gpio_pin_3(356) gpio_is_valid
[ 0.323126] gpio name is PL7, ret = 0
[ 0.323263] gpio name is PL3, ret = 0
[ 0.323386] gpio name is PL4, ret = 0
[ 0.323555] gpio_init finish with uesd
[ 0.324206] sw_uart_probe()1448 - uart0 error to get bt property
[ 0.324238] uart0: ttyS0 at MMIO 0x5000000 (irq = 32) is a SUNXI
[ 0.324255] sw_console_setup()1271 - console setup baud 115200 parity n bits 8, flow n
[ 1.444704] console [ttyS0] enabled
[ 1.449181] uart1: ttyS1 at MMIO 0x5000400 (irq = 33) is a SUNXI
[ 1.457078] misc dump reg init
[ 1.463873] loop: module loaded
[ 1.467337] Boot type 1
[ 1.470527] sunxi-wlan wlan: wlan_busnum (1)
[ 1.475204] sunxi-wlan wlan: wlan_usbnum (3)
[ 1.480064] sunxi-wlan wlan: Missing wlan_power.
[ 1.485126] sunxi-wlan wlan: wlan_power_name ((null))
[ 1.490851] sunxi-wlan wlan: io_regulator_name (axp806_bldo3)
[ 1.497181] sunxi-wlan wlan: wlan_regon gpio=387 mul-sel=1 pull=-1 drv_level=-1 data=0
[ 1.506553] sunxi-wlan wlan: wlan_en gpio=360 mul-sel=1 pull=-1 drv_level=-1 data=0
[ 1.515492] sunxi-wlan wlan: wlan_hostwake gpio=384 mul-sel=0 pull=-1 drv_level=-1 data=0
[ 1.525054] sunxi-wlan wlan: get gpio wlan_clk_gpio failed
[ 1.531179] sunxi-wlan wlan: clk not config
[ 1.536283] sunxi-bt bt: bt_power_name (vcc-wifi)
[ 1.541564] sunxi-bt bt: io_regulator_name (vcc-wifi-io)
[ 1.547390] sunxi-bt bt: bt_rst gpio=388 mul-sel=1 pull=-1 drv_level=-1 data=0
[ 1.556092] sunxi-bt bt: block state already is 1
[ 1.567567] __sid_efuse_key_is_readable()609 - The key oem write protect bit not burned!
[ 1.577800] tun: Universal TUN/TAP device driver, 1.6
[ 1.583438] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.590958] gmac-power1: NULL
[ 1.594210] gmac-power2: NULL
[ 1.599075] PPP generic driver version 2.4.2
[ 1.604122] PPP BSD Compression module registered
[ 1.609301] PPP Deflate Compression module registered
[ 1.615041] PPP MPPE Compression module registered
[ 1.620406] NET: Registered protocol family 24
[ 1.625299] PPTP driver version 0.8.5
[ 1.629503] hso: drivers/net/usb/hso.c: Option Wireless
[ 1.635608] usbcore: registered new interface driver hso
[ 1.641643] usbcore: registered new interface driver asix
[ 1.647749] usbcore: registered new interface driver ax88179_178a
[ 1.654675] usbcore: registered new interface driver cdc_ether
[ 1.661258] usbcore: registered new interface driver net1080
[ 1.667672] usbcore: registered new interface driver cdc_subset
[ 1.674351] usbcore: registered new interface driver zaurus
[ 1.680687] usbcore: registered new interface driver cdc_ncm
[ 1.686889] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.694463] get ehci0-controller, regulator_io is no nocare
[ 1.700731] [sunxi-ehci0]: probe, pdev->name: 5101000.ehci0-controller, sunxi_ehci: 0xffffffc000ea9b60, 0x:ffffff8001ff2000, irq_no:38
[ 1.714321] sunxi-ehci 5101000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.724424] sunxi-ehci 5101000.ehci0-controller: new USB bus registered, assigned bus number 1
[ 1.734383] sunxi-ehci 5101000.ehci0-controller: irq 56, io mem 0xffffffc0008a70e0
[ 1.760023] sunxi-ehci 5101000.ehci0-controller: USB 0.0 started, EHCI 1.00
[ 1.767714] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.775424] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.783470] usb usb1: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.791853] usb usb1: Manufacturer: Linux 3.10.65 ehci_hcd
[ 1.797864] usb usb1: SerialNumber: sunxi-ehci
[ 1.830146] hub 1-0:1.0: USB hub found
[ 1.834265] hub 1-0:1.0: 1 port detected
[ 1.838848] get ehci3-controller, regulator_io is no nocare
[ 1.845210] sunxi ehci3-controller is no enable
[ 1.850296] sunxi-ehci 5311000.ehci3-controller: init_sunxi_hci is fail
[ 1.857557] sunxi-ehci: probe of 5311000.ehci3-controller failed with error -1
[ 1.866042] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.873068] get ohci0-controller, regulator_io is no nocare
[ 1.879261] [sunxi-ohci0]: probe, pdev->name: 5101000.ohci0-controller, sunxi_ohci: 0xffffffc000ea8e40
[ 1.889776] sunxi-ohci 5101000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 1.899489] sunxi-ohci 5101000.ohci0-controller: new USB bus registered, assigned bus number 2
[ 1.909151] sunxi-ohci 5101000.ohci0-controller: irq 57, io mem 0xffffffc000ea8e40
[ 1.974004] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.981687] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.989614] usb usb2: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 1.997740] usb usb2: Manufacturer: Linux 3.10.65 ohci_hcd
[ 2.003866] usb usb2: SerialNumber: sunxi-ohci
[ 2.030146] hub 2-0:1.0: USB hub found
[ 2.034264] hub 2-0:1.0: 1 port detected
[ 2.038805] get ohci3-controller, regulator_io is no nocare
[ 2.045206] sunxi ohci3-controller is no enable
[ 2.050260] sunxi-ohci 5311000.ohci3-controller: init_sunxi_hci is fail
[ 2.057542] sunxi-ohci: probe of 5311000.ohci3-controller failed with error -1
[ 2.066288] get xhci-controller, regulator_io is no nocare
[ 2.072699] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 2.078721] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 3
[ 2.088005] xhci-hcd xhci-hcd.0.auto: irq 58, io mem 0x05200000
[ 2.094659] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.102227] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.110300] usb usb3: Product: xHCI Host Controller
[ 2.115648] usb usb3: Manufacturer: Linux 3.10.65 xhci-hcd
[ 2.121866] usb usb3: SerialNumber: xhci-hcd.0.auto
[ 2.127609] xHCI xhci_add_endpoint called for root hub
[ 2.133402] xHCI xhci_check_bandwidth called for root hub
[ 2.160143] hub 3-0:1.0: USB hub found
[ 2.164258] hub 3-0:1.0: 1 port detected
[ 2.168672] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 2.174934] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 4
[ 2.183527] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 2.191122] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.199046] usb usb4: Product: xHCI Host Controller
[ 2.204629] usb usb4: Manufacturer: Linux 3.10.65 xhci-hcd
[ 2.210746] usb usb4: SerialNumber: xhci-hcd.0.auto
[ 2.216437] xHCI xhci_add_endpoint called for root hub
[ 2.222165] xHCI xhci_check_bandwidth called for root hub
[ 2.250143] hub 4-0:1.0: USB hub found
[ 2.254260] hub 4-0:1.0: 1 port detected
[ 2.259231] usbcore: registered new interface driver usb-storage
[ 2.266067] usbcore: registered new interface driver ums-alauda
[ 2.272771] usbcore: registered new interface driver ums-cypress
[ 2.279546] usbcore: registered new interface driver ums-datafab
[ 2.286354] usbcore: registered new interface driver ums_eneub6250
[ 2.293331] usbcore: registered new interface driver ums-freecom
[ 2.300124] usbcore: registered new interface driver ums-isd200
[ 2.306793] usbcore: registered new interface driver ums-jumpshot
[ 2.313685] usbcore: registered new interface driver ums-karma
[ 2.320264] usbcore: registered new interface driver ums-onetouch
[ 2.327150] usbcore: registered new interface driver ums-realtek
[ 2.333931] usbcore: registered new interface driver ums-sddr09
[ 2.340613] usbcore: registered new interface driver ums-sddr55
[ 2.347280] usbcore: registered new interface driver ums-usbat
[ 2.354018] usbcore: registered new interface driver usbserial
[ 2.360630] usbcore: registered new interface driver option
[ 2.366911] usbserial: USB Serial support registered for GSM modem (1-port)
[ 2.375398] mousedev: PS/2 mouse device common for all mice
[ 2.381828] usbcore: registered new interface driver xpad
[ 2.387950] usbcore: registered new interface driver usb_acecad
[ 2.394628] usbcore: registered new interface driver aiptek
[ 2.400955] usbcore: registered new interface driver gtco
[ 2.407051] usbcore: registered new interface driver hanwang
[ 2.413477] usbcore: registered new interface driver kbtab
[ 2.419687] usbcore: registered new interface driver wacom
[ 2.426833] sunxi-rtc rtc: rtc core: registered sunxi-rtc as rtc0
[ 2.433650] sunxi-rtc rtc: RTC enabled
[ 2.438405] IR NEC protocol handler initialized
[ 2.443460] IR RC5(x) protocol handler initialized
[ 2.448734] IR RC6 protocol handler initialized
[ 2.453865] IR JVC protocol handler initialized
[ 2.458846] IR Sony protocol handler initialized
[ 2.464071] IR RC5 (streamzap) protocol handler initialized
[ 2.470296] IR SANYO protocol handler initialized
[ 2.475450] IR MCE Keyboard/mouse protocol handler initialized
[ 2.482057] sunxi cedar version 0.1
[ 2.486028] VE: install start!!!
[ 2.486028]
[ 2.491422] cedar_ve: cedar-ve the get irq is 121
[ 2.496958] VE: install end!!!
[ 2.496958]
[ 2.502241] google_vp9: sunxi google vp9 version 0.1
[ 2.507735] google_vp9: [google vp9]: install start!!!
[ 2.513645] google_vp9: google vp9: the get irq is 122
[ 2.519627] google_vp9: [cedar]: install end!!!
[ 2.525473] input: axp80-powerkey as /devices/soc/pmu0/axp80-powerkey/input/input0
[ 2.550891] sunxi gpu cooling probe start !
[ 2.555485] CPU gpu cooling register Success
[ 2.560771] device-mapper: uevent: version 1.0.3
[ 2.566230] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 2.575750] Bluetooth: HCI UART driver ver 2.2
[ 2.580710] Bluetooth: HCI H4 protocol initialized
[ 2.585968] Bluetooth: HCI Realtek H5 protocol initialized
[ 2.592170] rtk_btcoex: rtk_uart_coex_init, version: 1.1
[ 2.597999] rtk_btcoex: create workqueue
[ 2.603136] [cpufreq] use dvfs_table_0
[ 2.613483] cpuidle: using governor ladder
[ 2.617976] cpuidle: using governor menu
[ 2.623568] sunxi-mmc sdc0: SD/MMC/SDIO Host Controller Driver(v0.83 2017-08-17 16:22) Compiled in Nov 22 2017 at 12:51:10
[ 2.635923] sunxi-mmc sdc0: ***ctl-spec-caps*** 80
[ 2.641280] sunxi-mmc sdc0: regulator prop vmmc,str vcc-sdcv
[ 2.647492] sunxi-mmc sdc0: regulator prop vqmmc,str vcc-sdcvq33
[ 2.654301] sunxi-mmc sdc0: regulator prop vdmmc,str vcc-sdcvd
[ 2.662124] sunxi-mmc sdc0: no earse
[ 2.666082] sunxi-mmc sdc0: Got CD GPIO #166.
[ 2.671184] sunxi-mmc sdc0: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.700017] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.730117] sunxi-mmc sdc0: base:0xffffff800221e000 irq:67
[ 2.736143] sunxi-mmc sdc0: smc 0 p0 err, cmd 52, RTO !!
[ 2.742502] sunxi-mmc sdc2: SD/MMC/SDIO Host Controller Driver(v0.83 2017-08-17 16:22) Compiled in Nov 22 2017 at 12:51:10
[ 2.754842] sunxi-mmc sdc0: smc 0 p0 err, cmd 52, RTO !!
[ 2.760788] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.760805] sunxi-mmc sdc2: regulator prop vmmc,str vcc-emmcv
[ 2.760809] sunxi-mmc sdc2: regulator prop vqmmc,str vcc-emmcvq18
[ 2.760813] sunxi-mmc sdc2: regulator prop vdmmc,str none
[ 2.760872] sunxi-mmc sdc2: No vdmmc regulator found
[ 2.797626] sunxi-mmc sdc2: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.798737] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.800915] sunxi-mmc sdc0: smc 0 p0 err, cmd 5, RTO !!
[ 2.801734] sunxi-mmc sdc0: smc 0 p0 err, cmd 5, RTO !!
[ 2.802555] sunxi-mmc sdc0: smc 0 p0 err, cmd 5, RTO !!
[ 2.803375] sunxi-mmc sdc0: smc 0 p0 err, cmd 5, RTO !!
[ 2.804005] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 15 width 1 timing LEGACY(SDR12) dt B
[ 2.804043] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 15 width 1 timing LEGACY(SDR12) dt B
[ 2.806433] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 15 width 1 timing LEGACY(SDR12) dt B
[ 2.876309] mmc0: host does not support reading read-only switch. assuming write-enable.
[ 2.887292] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 15 width 1 timing SD-HS(SDR25) dt B
[ 2.890017] sunxi-mmc sdc2: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.908782] sunxi-mmc sdc0: sdc set ios: clk 50000000Hz bm PP pm ON vdd 15 width 1 timing SD-HS(SDR25) dt B
[ 2.910030] sunxi-mmc sdc2: base:0xffffff8002226000 irq:69
[ 2.910307] sunxi-mmc sdc1: SD/MMC/SDIO Host Controller Driver(v0.83 2017-08-17 16:22) Compiled in Nov 22 2017 at 12:51:10
[ 2.910324] sunxi-mmc sdc1: Can't get vmmc regulator string
[ 2.910327] sunxi-mmc sdc1: Can't get vqmmc regulator string
[ 2.910330] sunxi-mmc sdc1: Can't get vdmmc regulator string
[ 2.910331] get() with no identifier
[ 2.910332] get() with no identifier
[ 2.910333] get() with no identifier
[ 2.910335] sunxi-mmc sdc1: No vmmc regulator found
[ 2.910337] sunxi-mmc sdc1: No vqmmc regulator found
[ 2.910340] sunxi-mmc sdc1: No vdmmc regulator found
[ 2.985460] sunxi-mmc sdc0: sdc set ios: clk 50000000Hz bm PP pm ON vdd 15 width 4 timing SD-HS(SDR25) dt B
[ 2.996371] mmc0: new high speed SDHC card at address 0001
[ 3.002709] sunxi-mmc sdc1: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.013038] mmcblk0: mmc0:0001 ASTC 7.28 GiB
[ 3.013041] sunxi-mmc sdc1: no vqmmc,Check if there is regulator
[ 3.025534] mmcblk0: p1 p2 p3 < p5 p6 p7 >
[ 3.030018] sunxi-mmc sdc1: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.042751] sunxi-mmc sdc2: smc 1 p2 err, cmd 52, RTO !!
[ 3.049493] sunxi-mmc sdc2: smc 1 p2 err, cmd 52, RTO !!
[ 3.050047] sunxi-mmc sdc1: base:0xffffff800222e000 irq:68
[ 3.050747] [EMCE]:Unsupport Current Storage!
[ 3.050749] sunxi_emce_probe()474emce hw init failed!
[ 3.050760] emce: probe of emce failed with error -22
[ 3.051012] hidraw: raw HID events driver (C) Jiri Kosina
[ 3.054983] PT71600 Driver - version 2.0.0-Half-IMA!
[ 3.055159] usbcore: registered new interface driver usbhid
[ 3.055161] usbhid: USB HID core driver
[ 3.055547] zram: Created 1 device(s) ...
[ 3.104308] sunxi-mmc sdc2: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.116554] ashmem: initialized
[ 3.117609] sunxi-mmc sdc2: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.119482] sunxi-mmc sdc2: smc 1 p2 err, cmd 8, RTO !!
[ 3.120302] sunxi-mmc sdc2: smc 1 p2 err, cmd 5, RTO !!
[ 3.121119] sunxi-mmc sdc2: smc 1 p2 err, cmd 5, RTO !!
[ 3.121937] sunxi-mmc sdc2: smc 1 p2 err, cmd 5, RTO !!
[ 3.122754] sunxi-mmc sdc2: smc 1 p2 err, cmd 5, RTO !!
[ 3.123574] sunxi-mmc sdc2: smc 1 p2 err, cmd 55, RTO !!
[ 3.124391] sunxi-mmc sdc2: smc 1 p2 err, cmd 55, RTO !!
[ 3.125209] sunxi-mmc sdc2: smc 1 p2 err, cmd 55, RTO !!
[ 3.126027] sunxi-mmc sdc2: smc 1 p2 err, cmd 55, RTO !!
[ 3.126037] sunxi-mmc sdc2: sdc set ios: clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.126884] sunxi-mmc sdc2: smc 1 p2 err, cmd 1, RTO !!
[ 3.126894] sunxi-mmc sdc2: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[ 3.130279] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE !!
[ 3.130303] sunxi-mmc sdc1: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.132975] sunxi-mmc sdc1: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.134322] sunxi-mmc sdc1: smc 2 p1 err, cmd 8, RE !!
[ 3.134345] mmc2: host doesn't support card's voltages
[ 3.134348] mmc2: error -22 whilst initialising SDIO card
[ 3.134597] sunxi-mmc sdc1: smc 2 p1 err, cmd 55, RE !!
[ 3.134870] sunxi-mmc sdc1: smc 2 p1 err, cmd 55, RE !!
[ 3.134894] sunxi-mmc sdc1: sdc set ios: clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.135479] sunxi-mmc sdc1: smc 2 p1 err, cmd 1, RE !!
[ 3.135488] sunxi-mmc sdc1: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[ 3.293994] logger: created 256K log 'log_main'
[ 3.299163] logger: created 256K log 'log_events'
[ 3.304561] logger: created 256K log 'log_radio'
[ 3.309827] logger: created 256K log 'log_system'
[ 3.315959] usbcore: registered new interface driver snd-usb-audio
[ 3.323921] failed to get gpio-spdif gpio from dts,spdif_gpio:-2
[ 3.333860] sndahub sound.3: sunxi-ahub-aif1 <-> 5097000.cpudai0-controller mapping ok
[ 3.343998] sndahub sound.3: sunxi-ahub-aif2 <-> 5097000.cpudai1-controller mapping ok
[ 3.353950] sndahub sound.3: sunxi-ahub-aif3 <-> 5097000.cpudai2-controller mapping ok
[ 3.364737] sndhdmi sndhdmi: sndhdmi <-> 5097000.ahub_daudio1 mapping ok
[ 3.374559] sndspdif sndspdif: spdif-hifi <-> spdif mapping ok
[ 3.382157] u32 classifier
[ 3.385126] Actions configured
[ 3.388857] Netfilter messages via NETLINK v0.30.
[ 3.394261] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 3.401378] ctnetlink v0.93: registering with nfnetlink.
[ 3.407261] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 3.415133] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 3.421959] xt_time: kernel timezone is -0000
[ 3.426790] ipip: IPv4 over IPv4 tunneling driver
[ 3.432453] gre: GRE over IPv4 demultiplexor driver
[ 3.437806] ip_gre: GRE over IPv4 tunneling driver
[ 3.443985] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.450035] arp_tables: (C) 2002 David S. Miller
[ 3.455132] TCP: bic registered
[ 3.458574] TCP: cubic registered
[ 3.462417] TCP: westwood registered
[ 3.466337] TCP: htcp registered
[ 3.469876] Initializing XFRM netlink socket
[ 3.475228] NET: Registered protocol family 10
[ 3.480846] mip6: Mobile IPv6
[ 3.484116] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.490362] sit: IPv6 over IPv4 tunneling driver
[ 3.495963] NET: Registered protocol family 17
[ 3.500944] NET: Registered protocol family 15
[ 3.506005] Bluetooth: RFCOMM TTY layer initialized
[ 3.511463] Bluetooth: RFCOMM socket layer initialized
[ 3.517101] Bluetooth: RFCOMM ver 1.11
[ 3.521377] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.527205] Bluetooth: BNEP filters: protocol multicast
[ 3.533134] Bluetooth: BNEP socket layer initialized
[ 3.538582] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.545281] Bluetooth: HIDP socket layer initialized
[ 3.551157] Registering SWP/SWPB emulation handler
[ 3.557409] HDMI 2.0 driver init start!
[ 3.562047] [DISP] boot_disp:0x0
[ 3.565585] boot_hdmi=false
[ 3.568676] hdmi reg base:0xffffffc042c00000 esm_hpi_base:0xffffffc042c08000
[ 3.578411] HDMI2.0 module init end
[ 3.582756] [DISP] boot_disp:0x0
[ 4.180025] [HDMI receive params]: tv mode: 0xa format:0x1 data bits:0x0 eotf:0x4 cs:0x101 dvi_hdmi:2 range:2 scan:0 aspect_ratio:8
[ 5.190223] [HDMI2.0]CEA VIC=16:
[ 5.193665] 1920x1080p@60 Hz
[ 5.196922] 16:9, 8-bpp
[ 5.199702] YCbCr-444
[ 5.202592] BT709
[ 5.204698] eotf:SDR_LUMINANCE_RANGE
[ 5.321079] [DISP] disp_device_attached_and_enable,line:192:attched ok, mgr0<-->dev0
[ 5.329585] [DISP] disp_device_attached_and_enable,line:205:type:4,mode:10,fmt:yuv444,bits:8bits,eotf:4,cs:257 dvi_hdmi:2, range:2 scan:0 ratio:8
[ 5.344861] __sid_efuse_key_is_readable()609 - The key oem write protect bit not burned!
[ 5.372527] usb_serial_number:20080411
[ 5.376986] file system registered
[ 5.381671] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 5.389219] android_usb gadget: Number of LUNs=3
[ 5.394499] lun0: LUN: removable file: (no medium)
[ 5.399851] lun1: LUN: removable file: (no medium)
[ 5.405383] lun2: LUN: removable file: (no medium)
[ 5.411159] android_usb gadget: android_usb ready
[ 5.416469] sunxi-rtc rtc: hctosys: unable to read the hardware clock
[ 5.427280] snddaudio snddaudio2: codec: snd-soc-dummy, codec_dai: snd-soc-dummy-dai.
[ 5.436290] snddaudio snddaudio2: snd-soc-dummy-dai <-> 5097000.ahub_daudio2 mapping ok
[ 5.445963] snddaudio snddaudio3: codec: acx00-codec, codec_dai: acx00-dai.
[ 5.510402] snddaudio snddaudio3: acx00-dai <-> 5097000.ahub_daudio3 mapping ok
[ 5.519563] ALSA device list:
[ 5.522881] #0: sndahub
[ 5.525762] #1: sndhdmi
[ 5.528631] #2: sndspdif
[ 5.531744] #3: snddaudio2
[ 5.534899] #4: sndacx00-codec
[ 5.538626] Freeing unused kernel memory: 564K (ffffffc000b6f000 - ffffffc000bfc000)
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment