Skip to content

Instantly share code, notes, and snippets.

@Icenowy

Icenowy/log3_改正initrc的系统分区.txt

Created December 26, 2016 17:06
  • Star 0 You must be signed in to star a gist
  • Fork 0 You must be signed in to fork a gist
Star You must be signed in to star a gist
Embed
What would you like to do?
Learn more about clone URLs
Download ZIP
Some boot message of Lichee Pi Zero (V3s)
Raw
log3_改正initrc的系统分区.txt
HELLO! BOOT0 is starting!
get_ifm reg_val=7
setting pmu vol system core 1.1 v
===i2c gpio === 22777777
axp read fail, maybe no pmu
set pmu vol failed,maybe no pmu
DRAM DRIVE INFO: V0.7
DRAM Type = 2 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM CLK = 360 MHz
DRAM zq value: 000039bb
DRAM size = 64 MB
card boot number = 0
card no is 0
sdcard 0 line count 0
[mmc]: mmc driver ver 2014-8-11 15:06:39
[mmc]: ***Try SD card 0***
[mmc]: SD/MMC Card: 4bit, capacity: 1921MB
[mmc]: vendor: Man 00003000 Snr 00000be6
[mmc]: product: APPSD
[mmc]: revision: 0.0
[mmc]: ***SD/MMC 0 init OK!!!***
sdcard 0 init ok
The size of uboot is 00080000.
sum=444f35ce
src_sum=444f35ce
Succeed in loading uboot from sdmmc flash.
Jump to secend Boot.
[ 0.223]
U-Boot 2011.09-rc1-dirty (Jun 16 2015 - 13:24:29) Allwinner Technology
[ 0.231]version: 1.1.0
[ 0.236]pmbus:
===i2c gpio === 22777777
ready
axp read error
probe axp20x failed
axp_probe fail,run clock=1008
set power on vol to default
axp_set_power_supply_output dcdc2_vol = 1200
axp set dcdc2_vol to 1200 failed
axp_set_power_supply_output dcdc3_vol = 3300
axp set dcdc3_vol to 3300 failed
axp_set_power_supply_output aldo2_vol = 2500
axp set aldo2_vol to 2500 failed
axp_set_power_supply_output aldo3_vol = 3000
axp set aldo3_vol to 3000 failed
axp_set_power_supply_output ldo1_vol = 3300
axp set ldo1_vol to 3300 failed
axp_set_power_supply_output ldo2_vol = 3000
axp set ldo2_vol to 3000 failed
fel key new mode
run key detect
no key found
[ 0.312]DRAM: 64 MiB
save config for small mem_size
workmode = 0
MMC: 0
[ 0.367][mmc]: mmc driver ver 2014-9-1 10:54:35
[ 0.371][mmc]: get sdc_f_max fail,use default sdc_f_max 50000000
[ 0.377][mmc]: get sdc_ex_dly_used fail,use default dly
[ 0.383][mmc]: SUNXI SD/MMC: 0
[ 0.396][mmc]: ************Try SD card 0************
[ 0.433][mmc]: MID 000000 PSN 00000be6
[ 0.436][mmc]: PNM APPSD -- 0x41-50-50-53-44-05
[ 0.441][mmc]: PRV 0.0
[ 0.443][mmc]: MDT m-12 y-2015
[ 0.447][mmc]: ---------------mmc->clock 25000000-----------
[ 0.452][mmc]: ---------------mmc->bus_width 4--------------
[ 0.458][mmc]: SD/MMC Card: 4bit, capacity: 1921MB
[ 0.463][mmc]: boot0 capacity: 0KB,boot1 capacity: 0KB
[ 0.468][mmc]: ************SD/MMC 0 init OK!!!************
[ 0.474]sunxi flash init ok
env_relocate_spec storage_type = 1
@@@@@@@[debug_jaosn]:this is for ipc @@@@@@@
In: serial
Out: serial
Err: serial
bootcmd set setargs_mmc
to be run cmd=run setargs_mmc boot_normal
WORK_MODE_BOOT
read bootlogo partition successful,start_block=0x3ba0,rblock=0x100 ,ret=256
Use decode 1x1 sampling
sunxi_read_bootlogo: jpg convert argb
[ 0.671]Hit any key to stop autoboot: 0
read boot or recovery all
[ 1.013]sunxi flash read :offset 4000, 3553724 bytes OK
no signature
[ 1.020]ready to boot
para err in disp_ioctl, cmd = 0xa,screen id = 1
[ 1.027][mmc]: MMC Device 2 not found
[ 1.030][mmc]: mmc not find,so not exit
reload config to 0x43000000
[ 1.035]
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Linux version 3.4.39 (zp@ubuntu) (gcc version 4.6.3 20120201 (prerelease) (crosstool-NG linaro-1.13.1-2012.02-20120222 - Linaro GCC 2012.02) ) #12 Tue Dec 27 00:52:16 CST 2016
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: sun8i
[ 0.000000] Initialized persistent memory from 41d20800-41d307ff
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat c0492dcc, node_mem_map c052d000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] script_init enter!
[ 0.000000] script_init exit!
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p7 init=/init loglevel=8 partitions= mac_addr= uid=1234567890 fb_base=0x43e80000 boot_type=1 config_size=32720
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 64MB = 64MB total
[ 0.000000] Memory: 30496k/30496k available, 35040k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc4800000 - 0xff000000 ( 936 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc042e000 (4248 kB)
[ 0.000000] .init : 0xc042e000 - 0xc0450000 ( 136 kB)
[ 0.000000] .data : 0xc0450000 - 0xc0493500 ( 270 kB)
[ 0.000000] .bss : 0xc0493524 - 0xc052c8cc ( 613 kB)
[ 0.000000] NR_IRQS:544
[ 0.000000] 524 ahb1 set parent pll_periph0d2
[ 0.000000] Architected local timer running at 24.00MHz.
[ 0.000000] Switching to timer-based delay loop
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000159] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000)
[ 0.000181] pid_max: default: 32768 minimum: 301
[ 0.000314] Mount-cache hash table entries: 512
[ 0.000817] CPU: Testing write buffer coherency: ok
[ 0.001076] Setting up static identity map for 0x40318540 - 0x40318598
[ 0.001731] devtmpfs: initialized
[ 0.003544] pinctrl core: initialized pinctrl subsystem
[ 0.004032] NET: Registered protocol family 16
[ 0.004394] DMA: preallocated 128 KiB pool for atomic coherent allocations
[ 0.004449] script_sysfs_init success
[ 0.004483] sunxi_dump_init success
[ 0.005206] gpiochip_add: registered GPIOs 0 to 223 on device: sunxi-pinctrl
[ 0.006119] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver
[ 0.006485] gpiochip_add: registered GPIOs 1024 to 1031 on device: axp-pinctrl
[ 0.007345] persistent_ram: error in header, 2
[ 0.007361] persistent_ram: found existing buffer, size 1356, start 1356
[ 0.020012] console [ram-1] enabled
[ 0.020409] [sunxi-module]: [sunxi-module.0] probe success
[ 0.020620] axp driver uning configuration failed(801)
[ 0.020813] axp driver uning configuration failed(808)
[ 0.021196] Not Found clk pll_isp in script
[ 0.021396] Not Found clk pll_video in script
<5>[ 0.021502] Not Found clk pll_ve in script
[ 0.021607] Not Found clk pll_periph0 in script
[ 0.021798] Not Found clk pll_de in script
[ 0.021900] sunxi_default_clk_init
[ 0.022001] try to set pll6ahb1 to 200000000
[ 0.022198] Error not get clk pll6ahb1
[ 0.022306] Error not get clk pll6ahb1try to set ahb1 to 200000000
[ 0.022610] try to set apb1 to 100000000
[ 0.022999] ===fe3o4==== sunxi_root_procfs_attach ret:0
[ 0.026278] bio: create slab <bio-0> at 0
[ 0.026642] pwm module init!
[ 0.028826] SCSI subsystem initialized
[ 0.029089] usbcore: registered new interface driver usbfs
[ 0.029346] usbcore: registered new interface driver hub
[ 0.029588] usbcore: registered new device driver usb
[ 0.029908] twi_chan_cfg()340 - [twi0] has no twi_regulator.
[ 0.030022] twi_chan_cfg()340 - [twi1] has no twi_regulator.
[ 0.030909] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x34)
[ 0.031122] axp20_board 0-0034: failed reading at 0x03
[ 0.031227] [AXP20-MFD] try to read chip id failed!
[ 0.031331] axp mfd register failed
[ 0.031532] axp20_board: probe of 0-0034 failed with error -70
[ 0.031683] Linux video capture interface: v2.00
[ 0.031959] gpiochip_add: gpios 1024..1028 (axp_pin) failed to register
[ 0.032067] axp pinctrl used,skip
[ 0.032570] Advanced Linux Sound Architecture Driver Version 1.0.25.
[ 0.033379] Switching to clocksource arch_sys_counter
[ 0.039994] NET: Registered protocol family 2
[ 0.039994] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.039994] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.040093] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.040304] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.040410] TCP: reno registered
[ 0.040603] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.040720] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.041180] NET: Registered protocol family 1
[ 0.041497] Unpacking initramfs...
[ 0.056256] Freeing initrd memory: 220K
[ 0.056646] [pm]aw_pm_init!
[ 0.056757] standby_mode = 1.
[ 0.056862] wakeup src cnt is : 3.
[ 0.057058] pmu name: pmu1_para .
[ 0.057169] pmu1_enable = 0x1.
[ 0.057273] pmux_id = 0x1.
[ 0.057379] pmu name: pmu2_para .
[ 0.057569] config_pmux_para: script_parser_fetch err.
[ 0.057673] pmu2_enable = 0x0.
[ 0.057781] add_sys_pwr_dm: get ldo name failed
[ 0.057970] add_sys_pwr_dm: get ldo name failed
[ 0.058073] add_sys_pwr_dm: get ldo name failed
[ 0.058262] add_sys_pwr_dm: get ldo name failed
[ 0.058366] add_sys_pwr_dm: get ldo name failed
[ 0.058470] add_sys_pwr_dm: get ldo name failed
[ 0.058660] add_sys_pwr_dm: get ldo name failed
[ 0.058765] add_sys_pwr_dm: get ldo name failed
[ 0.058954] add_sys_pwr_dm: get ldo name failed
[ 0.059058] add_sys_pwr_dm: get ldo name failed
[ 0.059161] after inited: sys_mask config = 0x0.
[ 0.059352] dynamic_standby enalbe = 0x0.
[ 0.059526] sunxi_reg_init enter
[ 0.061481] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.061723] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.062102] msgmni has been set to 59
[ 0.063150] io scheduler noop registered
[ 0.063268] io scheduler deadline registered
[ 0.063528] io scheduler cfq registered (default)
[ 0.064027] [DISP]disp_module_init
[ 0.064516] cmdline,disp=
[ 0.065217] rotation_sw module is config as no used
[ 0.065348] [DISP] disp_get_rotation_sw,line:68:disp 0 out of range? g_rot_sw=0
[ 0.065637] [DISP] disp_init_connections,line:289:NULL pointer: 0, 0
[ 0.080860] [DISP] disp_sys_power_enable,line:387:some error happen, fail to get regulator
[ 0.081882] [DISP]disp_module_init finish
[ 0.082287] sw_uart_get_devinfo()1503 - uart0 has no uart_regulator.
[ 0.082827] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
[ 0.082949] sw_uart_pm()890 - uart0 clk is already enable
[ 0.083155] sw_console_setup()1233 - console setup baud 115200 parity n bits 8, flow n
[ 0.275339] console [ttyS0] enabled
[ 0.895449] sunxi_spi_chan_cfg()1376 - [spi-0] has no spi_regulator.
[ 0.903352] spi spi0: master is unqueued, this is deprecated
[ 0.909982] m25p_probe()966 - Use the Dual Mode Read.
[ 0.915805] NorFlash ID: 0xef4018 - 0x0
[ 0.920193] m25p80 spi0.0: found W25q128, expected at25df641
[ 0.926671] m25p80 spi0.0: W25q128 (16384 Kbytes)
[ 0.933485] partitions_register()853 - Invalid partitions count: -1
[ 0.941127] Creating 1 MTD partitions on "spi0.0":
[ 0.946565] 0x000000000000-0x000001000000 : "NorFlash part0"
[ 0.954098] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.981753] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.990975] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus number 1
[ 0.999682] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000
[ 1.020032] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00
[ 1.027460] hub 1-0:1.0: USB hub found
[ 1.031865] hub 1-0:1.0: 1 port detected
[ 1.036748] sunxi-ehci sunxi-ehci.1: remove, state 1
[ 1.042607] usb usb1: USB disconnect, device number 1
[ 1.343040] sunxi-ehci sunxi-ehci.1: USB bus 1 deregistered
[ 1.359535] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.386624] sunxi-ohci sunxi-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 1.395361] sunxi-ohci sunxi-ohci.1: new USB bus registered, assigned bus number 1
[ 1.404003] sunxi-ohci sunxi-ohci.1: irq 105, io mem 0xf1c1a400
[ 1.474629] hub 1-0:1.0: USB hub found
[ 1.479026] hub 1-0:1.0: 1 port detected
[ 1.483879] sunxi-ohci sunxi-ohci.1: remove, state 1
[ 1.489502] usb usb1: USB disconnect, device number 1
[ 1.495895] sunxi-ohci sunxi-ohci.1: USB bus 1 deregistered
[ 1.512333] Initializing USB Mass Storage driver...
[ 1.518005] usbcore: registered new interface driver usb-storage
[ 1.524800] USB Mass Storage support registered.
[ 1.530416] file system registered
[ 1.535738] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 1.543647] android_usb gadget: Number of LUNs=1
[ 1.548867] lun0: LUN: removable file: (no medium)
[ 1.554837] android_usb gadget: android_usb ready
[ 1.560415] sunxikbd_script_init: key para not found, used default para.
[ 1.569006] sunxi-rtc sunxi-rtc: rtc core: registered sunxi-rtc as rtc0
[ 1.576767] sunxi cedar version 0.1
[ 1.580905] [cedar]: install start!!!
[ 1.585446] [cedar]: install end!!!
[ 1.589852] platform reg-20-cs-dcdc2: Driver reg-20-cs-dcdc2 requests probe deferral
[ 1.598823] platform reg-20-cs-dcdc3: Driver reg-20-cs-dcdc3 requests probe deferral
[ 1.607645] platform reg-20-cs-ldo1: Driver reg-20-cs-ldo1 requests probe deferral
[ 1.616388] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[ 1.625098] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[ 1.633730] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[ 1.642439] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[ 1.651439] sunxi_wdt_init_module: sunxi WatchDog Timer Driver v1.0
[ 1.658774] sunxi_wdt_probe: devm_ioremap return wdt_reg 0xf1c20ca0, res->start 0x01c20ca0, res->end 0x01c20cbf
[ 1.670193] sunxi_wdt_probe: initialized (g_timeout=16s, g_nowayout=0)
[ 1.677930] wdt_enable, write reg 0xf1c20cb8 val 0x00000000
[ 1.684232] wdt_set_tmout, write 0x000000b0 to mode reg 0xf1c20cb8, actual timeout 16 sec
[ 1.694075] [mmc]: SD/MMC/SDIO Host Controller Driver(v1.114 2015-6-2 10:21) Compiled in Dec 26 2016 at 23:50:50
[ 1.705632] [mmc]: get mmc0's sdc_power failed
[ 1.710682] [mmc]: MMC host used card: 0x1, boot card: 0x1, io_card 0
[ 1.718742] [mmc]: sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 1.729883] [mmc]: sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 1.739812] sunxi_leds_fetch_sysconfig_para leds is not used in config
[ 1.747272] =========script_get_err============
[ 1.752423] [mmc]: sdc0 power_supply is null
[ 1.758771] usbcore: registered new interface driver usbhid
[ 1.765082] usbhid: USB HID core driver
[ 1.770081] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 1.780527] ashmem: initialized
[ 1.784354] logger: created 256K log 'log_main'
[ 1.789807] logger: created 32K log 'log_events'
[ 1.795227] logger: created 32K log 'log_radio'
[ 1.800627] logger: created 32K log 'log_system'
[ 1.805863] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO !!
[ 1.815124] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO !!
[ 1.823621] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 1.835448] asoc: sndcodec <-> sunxi-codec mapping ok
[ 1.844929] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 1.856035] TCP: cubic registered
[ 1.859854] NET: Registered protocol family 17
[ 1.865117] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 1.873936] ThumbEE CPU extension supported.
[ 1.879965] Registering SWP/SWPB emulation handler
[ 1.885517] *******************Try sdio*******************
[ 1.892542] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 1.901106] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[ 1.910131] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 1.918433] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[ 1.927049] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 1.935425] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[ 1.943942] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 1.952268] *******************Try sd *******************
[ 1.958401] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[ 1.967060] platform reg-20-cs-ldo1: Driver reg-20-cs-ldo1 requests probe deferral
[ 1.975678] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 1.986061] platform reg-20-cs-dcdc3: Driver reg-20-cs-dcdc3 requests probe deferral
[ 1.994916] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.005325] platform reg-20-cs-dcdc2: Driver reg-20-cs-dcdc2 requests probe deferral
[ 2.014225] sunxi-rtc sunxi-rtc: setting system clock to 1970-01-01 00:00:15 UTC (15)
[ 2.025575] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.036936] ALSA device list:
[ 2.040395] #0: audiocodec
[ 2.044277] Freeing init memory: 136K
[ 2.051727] init: skipping insecure file '/default.prop'
[ 2.057915] init: skipping insecure file '/init.rc'
[ 2.063828] init: /init.rc: 127: invalid option 'root'
[ 2.069689] init: skipping insecure file '/init.sun8i.rc'
[ 2.076135] init: /init.sun8i.rc: 52: invalid option 'root'
[ 2.082544] init: skipping insecure file 'init.sun8i.usb.rc'
[ 2.089766] init: command 'loglevel' r=0
[ 2.094309] [mmc]: sdc0 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.106290] init: skipping insecure file '/ueventd.rc'
[ 2.112269] init: command 'export' r=0
[ 2.116625] init: command 'export' r=0
[ 2.121183] init: skipping insecure file '/ueventd.sun8i.rc'
[ 2.130546] init: command 'export' r=0
[ 2.134889] init: command 'export' r=0
[ 2.139226] mmc0: Problem switching card into high-speed mode!
[ 2.145932] [mmc]: sdc0 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.160284] init: command 'symlink' r=0
[ 2.164744] init: command 'symlink' r=0
[ 2.169127] init: command 'symlink' r=0
[ 2.190518] [mmc]: sdc0 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 4 timing LEGACY(SDR12) dt B
[ 2.201180] init: command 'mkdir' r=0
[ 2.205486] init: command 'mkdir' r=0
[ 2.209714] init: command 'mkdir' r=0
[ 2.220331] mmc0: new SD card at address 21bd
[ 2.230252] init: command 'mkdir' r=-2
[ 2.234545] init: processing action 0x16c1098 (init)
[ 2.240349] mmcblk0: mmc0:21bd APPSD 1.87 GiB
[ 2.250336] init: command 'export' r=0
[ 2.254861] mmcblk0: p1 p2 p3 < p5 p6 p7 p8 p9 p10 >
[ 2.260839] init: command 'export' r=0
[ 2.265112] init: command 'export' r=0
[ 2.269370] init: command 'export' r=0
[ 2.277320] mmcblk mmc0:21bd: Card claimed for testing.
[ 2.283298] mmc0:21bd: APPSD 1.87 GiB
[ 2.287710] init: processing action 0x16bfc28 (early-fs)
[ 2.293855] platform reg-20-cs-dcdc2: Driver reg-20-cs-dcdc2 requests probe deferral
[ 2.302691] *******************sd init ok*******************
[ 2.309199] init: command 'mkdir' r=0
[ 2.313525] platform reg-20-cs-dcdc3: Driver reg-20-cs-dcdc3 requests probe deferral
[ 2.322445] init: command 'mkdir' r=0
[ 2.326656] init: command 'mkdir' r=0
[ 2.330931] platform reg-20-cs-ldo1: Driver reg-20-cs-ldo1 requests probe deferral
[ 2.339487] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[ 2.348130] init: processing action 0x16c2338 (console_init)
[ 2.354953] init: command 'console_init' r=0
[ 2.359813] init: processing action 0x16bff30 (fs)
[ 2.365369] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[ 2.374045] init: command 'wait' r=0
[ 2.378752] init: command 'setupfs' r=1
[ 2.383405] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[ 2.392006] init: out of loopback devices source = /dev/block/mmcblk0p5
[ 2.399568] init: out of loopback devices target = /system
[ 2.405926] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[ 2.414875] init: out of loopback devices system = squashfs
[ 2.421263] init: out of loopback devices options = (null)
[ 2.430796] init: command 'mount' r=0
[ 2.435143] init: command 'wait' r=0
[ 2.439246] init: out of loopback devices source = /dev/block/mmcblk0p6
[ 2.446725] init: out of loopback devices target = /data
[ 2.452816] init: out of loopback devices system = jffs2
[ 2.458815] init: out of loopback devices options = (null)
[ 2.465159] MTD: Attempt to mount non-MTD device "/dev/block/mmcblk0p6"
[ 2.472827] init: listdir = .
[ 2.476315] init: listdir = ..
[ 2.479798] init: listdir = mmcblk0p10
[ 2.484090] init: listdir = mmcblk0p9
[ 2.488349] init: listdir = mmcblk0p8
[ 2.492525] init: listdir = mmcblk0p7
[ 2.496681] init: listdir = mmcblk0p6
[ 2.500937] init: listdir = mmcblk0p5
[ 2.505094] init: listdir = mmcblk0p3
[ 2.509250] init: listdir = mmcblk0p2
[ 2.513501] init: listdir = mmcblk0p1
[ 2.517662] init: listdir = mmcblk0
[ 2.521676] init: listdir = platform
[ 2.525741] init: listdir = mtdblock0
[ 2.530055] init: do_mount errno=22
[ 2.534039] init: command 'mount' r=-1
[ 2.538332] init: processing action 0x16c0010 (post-fs)
[ 2.544342] init: out of loopback devices source = rootfs
[ 2.550451] init: out of loopback devices target = /
[ 2.556141] init: out of loopback devices system = rootfs
[ 2.562241] init: out of loopback devices options = (null)
[ 2.568568] init: command 'mount' r=0
[ 2.572752] init: processing action 0x16c0070 (post-fs-data)
[ 2.579301] init: command 'chown' r=0
[ 2.583518] init: command 'chmod' r=0
[ 2.587699] init: command 'chmod' r=0
[ 2.592044] init: command 'mkdir' r=0
[ 2.596216] init: command 'restorecon' r=0
[ 2.600920] init: command 'mkdir' r=0
[ 2.605195] init: command 'mkdir' r=0
[ 2.609371] init: processing action 0x16c0dc0 (post-fs-data)
[ 2.618449] init: skipping insecure file '/system/vendor/modules/videobuf-core.ko'
[ 2.637373] init: command 'insmod' r=0
[ 2.641889] init: skipping insecure file '/system/vendor/modules/videobuf-dma-contig.ko'
[ 2.651950] init: command 'insmod' r=0
[ 2.656381] init: skipping insecure file '/system/vendor/modules/cci.ko'
[ 2.687851] [VFE]cci probe start cci_sel = 0!
[ 2.692904] [VFE]cci probe end cci_sel = 0!
[ 2.697823] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[ 2.706848] [VFE]cci_init end
[ 2.710474] init: command 'insmod' r=0
[ 2.714896] init: skipping insecure file '/system/vendor/modules/vfe_os.ko'
[ 2.722947] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[ 2.732217] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[ 2.750434] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[ 2.759085] platform reg-20-cs-ldo1: Driver reg-20-cs-ldo1 requests probe deferral
[ 2.774367] init: command 'insmod' r=0
[ 2.778916] init: skipping insecure file '/system/vendor/modules/vfe_subdev.ko'
[ 2.787324] platform reg-20-cs-dcdc3: Driver reg-20-cs-dcdc3 requests probe deferral
[ 2.797144] platform reg-20-cs-dcdc2: Driver reg-20-cs-dcdc2 requests probe deferral
[ 2.806069] init: command 'insmod' r=0
[ 2.810492] init: skipping insecure file '/system/vendor/modules/h22_mipi.ko'
[ 2.819698] init: command 'insmod' r=0
[ 2.824200] init: skipping insecure file '/system/vendor/modules/vfe_v4l2.ko'
[ 2.944386] [VFE]Welcome to Video Front End driver
[ 2.950415] [VFE]pdev->id = 0
[ 2.953812] [VFE]dev->mipi_sel = 0
[ 2.957762] [VFE]dev->vip_sel = 0
[ 2.961586] [VFE]dev->isp_sel = 0
[ 2.971571] [VFE_WARN]vfe vpu clock is null
[ 2.982924] [ISP] isp platform_id = 6!
[ 2.987348] platform reg-20-cs-dcdc2: Driver reg-20-cs-dcdc2 requests probe deferral
[ 2.996199] [VFE]probe_work_handle start!
[ 3.000765] [VFE]..........................vfe clk open!.......................
[ 3.009168] [VFE]vfe_init end
[ 3.013003] init: command 'insmod' r=0
[ 3.017445] init: skipping insecure file '/system/vendor/modules/uvcvideo.ko'
[ 3.025745] platform reg-20-cs-dcdc3: Driver reg-20-cs-dcdc3 requests probe deferral
[ 3.034808] [VFE]v4l2 subdev register input_num = 0
[ 3.043003] platform reg-20-cs-ldo1: Driver reg-20-cs-ldo1 requests probe deferral
[ 3.051827] uvcvideo: Adding mapping Brightness to control 00000000-0000-0000-0000-000000000101/2.
[ 3.061895] [VFE_ERR]get regulator csi_avdd error!
[ 3.067400] [VFE_ERR]vfe_device_regulator_get error at input_num = 0
[ 3.074633] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[ 3.083256] uvcvideo: Adding mapping Contrast to control 00000000-0000-0000-0000-000000000101/3.
[ 3.093685] [VFE]V4L2 device registered as video0
[ 3.099078] [VFE]..........................vfe clk close!.......................
[ 3.107613] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[ 3.116247] uvcvideo: Adding mapping Hue to control 00000000-0000-0000-0000-000000000101/6.
[ 3.125678] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[ 3.134296] [VFE]probe_work_handle end!
[ 3.138771] uvcvideo: Adding mapping Saturation to control 00000000-0000-0000-0000-000000000101/7.
[ 3.148999] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[ 3.158005] uvcvideo: Adding mapping Sharpness to control 00000000-0000-0000-0000-000000000101/8.
[ 3.168067] uvcvideo: Adding mapping Gamma to control 00000000-0000-0000-0000-000000000101/9.
[ 3.177643] uvcvideo: Adding mapping Backlight Compensation to control 00000000-0000-0000-0000-000000000101/1.
[ 3.188942] uvcvideo: Adding mapping Gain to control 00000000-0000-0000-0000-000000000101/4.
[ 3.198501] uvcvideo: Adding mapping Power Line Frequency to control 00000000-0000-0000-0000-000000000101/5.
[ 3.209607] uvcvideo: Adding mapping Hue, Auto to control 00000000-0000-0000-0000-000000000101/16.
[ 3.219747] uvcvideo: Adding mapping Exposure, Auto to control 00000000-0000-0000-0000-000000000001/2.
[ 3.230186] uvcvideo: Adding mapping Exposure, Auto Priority to control 00000000-0000-0000-0000-000000000001/3.
[ 3.241578] uvcvideo: Adding mapping Exposure (Absolute) to control 00000000-0000-0000-0000-000000000001/4.
[ 3.252584] uvcvideo: Adding mapping White Balance Temperature, Auto to control 00000000-0000-0000-0000-000000000101/11.
[ 3.264848] uvcvideo: Adding mapping White Balance Temperature to control 00000000-0000-0000-0000-000000000101/10.
[ 3.276527] uvcvideo: Adding mapping White Balance Component, Auto to control 00000000-0000-0000-0000-000000000101/13.
[ 3.288595] uvcvideo: Adding mapping White Balance Blue Component to control 00000000-0000-0000-0000-000000000101/12.
[ 3.300566] uvcvideo: Adding mapping White Balance Red Component to control 00000000-0000-0000-0000-000000000101/12.
[ 3.312442] uvcvideo: Adding mapping Focus (absolute) to control 00000000-0000-0000-0000-000000000001/6.
[ 3.323158] uvcvideo: Adding mapping Focus, Auto to control 00000000-0000-0000-0000-000000000001/8.
[ 3.333394] uvcvideo: Adding mapping Zoom, Absolute to control 00000000-0000-0000-0000-000000000001/11.
[ 3.343932] uvcvideo: Adding mapping Zoom, Continuous to control 00000000-0000-0000-0000-000000000001/12.
[ 3.354747] uvcvideo: Adding mapping Privacy to control 00000000-0000-0000-0000-000000000001/17.
[ 3.364878] usbcore: registered new interface driver uvcvideo
[ 3.371512] USB Video Class driver (v1.0.8_SONiX_v2.6.36.04)
[ 3.377973] init: command 'insmod' r=0
[ 3.382391] init: skipping insecure file '/system/vendor/modules/da380.ko'
[ 3.391415] step1 : gsensor_fetch_sysconfig_para
[ 3.396662] step2 : gsensor_fetch_sysconfig_para
[ 3.402086] step3 : gsensor_fetch_sysconfig_para
[ 3.407306] step4 : mir3da_init
[ 3.411231] i2c-core: driver [da380] using legacy suspend method
[ 3.418013] i2c-core: driver [da380] using legacy resume method
[ 3.424805] richard mir3da_detect: mir3da_detect:bus[0] addr[0x27]
[ 3.437118] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x27)
[ 3.451662] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x27)
[ 3.466184] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x27)
[ 3.475462] [MIR3DA] Can't find Mir3da gsensor!!
[ 3.480842] init: command 'insmod' r=0
[ 3.485257] init: skipping insecure file '/system/vendor/modules/sw-device.ko'
[ 3.494827] sw_get_write_info:read erro or read null !
[ 3.500866] init: command 'insmod' r=0
[ 3.505152] init: processing action 0x16c2380 (property_service_init)
[ 3.512689] get write info erro!
[ 3.516556] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x18)
[ 3.527899] init: skipping insecure file '/system/build.prop'
[ 3.541137] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x18)
[ 3.568458] init: Created socket '/dev/socket/property_service' with mode '666', user '0', group '0'
[ 3.579097] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x18)
[ 3.588526] init: command 'property_service_init' r=0
[ 3.594270] init: processing action 0x16c23c8 (signal_init)
[ 3.600803] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x18)
[ 3.610234] init: command 'signal_init' r=0
[ 3.614986] init: processing action 0x16c2410 (check_startup)
[ 3.621542] init: command 'check_startup' r=0
[ 3.626572] init: processing action 0x16c01c8 (boot)
[ 3.632382] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x18)
[ 3.642172] init: command 'ifup' r=0
[ 3.646393] init: command 'hostname' r=0
[ 3.651065] init: command 'domainname' r=0
[ 3.655729] init: command 'setrlimit' r=0
[ 3.660475] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x19)
[ 3.669957] init: command 'chown' r=0
[ 3.674272] init: starting 'servicemanager'
[ 3.679602] init: starting 'vold'
[ 3.683632] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x19)
[ 3.694240] init: starting 'media'
[ 3.705002] init: Created socket '/dev/socket/vold' with mode '660', user '0', group '1009'
[ 3.715303] init: starting 'startupSound'
[ 3.720724] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x19)
[ 3.739244] init: command 'class_start' r=0
[ 3.750716] init: starting 'ccdr'
[ 3.755027] init: command 'class_start' r=0
[ 3.759837] init: processing action 0x16c0f30 (boot)
[ 3.766316] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x19)
[ 3.786578] init: starting 'adbd'
[ 3.794399] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x19)
[ 3.804357] init: command 'start' r=0
[ 3.808679] init: starting 'debuggerd'
[ 3.815791] init: Created socket '/dev/socket/adbd' with mode '660', user '1000', group '1000'
[ 3.840221] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x8)
[ 3.849883] init: command 'start' r=0
[ 3.856908] init: starting 'standby'
[ 3.861364] adb_open
[ 3.870365] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x8)
[ 3.880449] init: command 'start' r=0
[ 3.884667] init: processing action 0x16c2458 (queue_property_triggers)
[ 3.902379] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x8)
[ 3.930504] init: command 'queue_property_triggers' r=0
[ 3.936555] init: processing action 0x16c04a8 (property:ro.debuggable=1)
[ 3.945343] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x8)
[ 3.968332] init: starting 'console'
[ 3.973184] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x8)
[ 4.005470] init: command 'start' r=0
[ 4.009782] init: processing action 0x16c1d70 (property:sys.usb.config=mass_storage,adb)
[ 4.021148] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x38)
[ 4.031893] android_usb: already disabled
[ 4.036513] init: command 'write' r=0
[ 4.050415] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x38)
[ 4.060007] init: command 'write' r=0
[ 4.064489] init: command 'write' r=0
[ 4.068772] init: command 'write' r=0
[ 4.075758] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x38)
[ 4.100490] ep_matches, wrn: endpoint already claimed, ep(0xc0482984, 0xc1907380, ep1in-bulk)
[ 4.110870] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x38)
[ 4.129374] adb_bind_config
[ 4.132704] ep_matches, wrn: endpoint already claimed, ep(0xc0482984, 0xc1907380, ep1in-bulk)
[ 4.142396] ep_matches, wrn: endpoint already claimed, ep(0xc04829d0, 0xc1907380, ep1out-bulk)
[ 4.152077] ep_matches, wrn: endpoint already claimed, ep(0xc0482984, 0xc1907380, ep1in-bulk)
[ 4.161730] ep_matches, wrn: endpoint already claimed, ep(0xc04829d0, 0xc1907380, ep1out-bulk)
[ 4.171483] ep_matches, wrn: endpoint already claimed, ep(0xc0482a1c, 0xc1909300, ep2in-bulk)
[ 4.190608] init: command 'write' r=0
[ 4.194898] init: command 'setprop' r=0
[ 4.199512] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x38)
[ 4.230349] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x27)
[ 4.251145] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x27)
[ 4.281078] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x27)
[ 4.311052] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x27)
[ 4.350601] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x27)
[ 4.370837] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x26)
[ 4.414240] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x26)
[ 4.442914] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x26)
[ 4.470829] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x26)
[ 4.500635] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x26)
[ 4.520705] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1c)
[ 4.551100] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1c)
[ 4.581100] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1c)
[ 4.610289] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1c)
[ 4.630971] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1c)
[ 4.660283] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1d)
root@camdroid:/ # [ 4.688595] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1d)
[ 4.717478] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1d)
[ 4.741901] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1d)
[ 4.771078] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1d)
[ 4.800320] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4c)
[ 4.825496] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4c)
[ 4.850912] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4c)
[ 4.880419] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4c)
[ 4.916191] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4c)
[ 4.950280] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x3d)
[ 4.971124] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x3d)
[ 5.001070] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x3d)
[ 5.037033] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x3d)
[ 5.069956] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x3d)
[ 5.102347] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.125167] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus number 1
[ 5.140892] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x28)
[ 5.161498] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000
[ 5.170246] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x28)
[ 5.185417] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00
[ 5.193002] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x28)
[ 5.208130] hub 1-0:1.0: USB hub found
[ 5.220422] hub 1-0:1.0: 1 port detected
[ 5.225087] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[ 5.234279] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x28)
[ 5.260379] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[ 5.269059] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[ 5.290328] sunxi-ohci sunxi-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 5.299048] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x28)
[ 5.308477] sunxi-ohci sunxi-ohci.1: new USB bus registered, assigned bus number 2
[ 5.344729] sunxi-ohci sunxi-ohci.1: irq 105, io mem 0xf1c1a400
[ 5.360080] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[ 5.368652] platform reg-20-cs-ldo1: Driver reg-20-cs-ldo1 requests probe deferral
[ 5.405795] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x29)
[ 5.415381] platform reg-20-cs-dcdc3: Driver reg-20-cs-dcdc3 requests probe deferral
[ 5.441149] hub 2-0:1.0: USB hub found
[ 5.445451] hub 2-0:1.0: 1 port detected
[ 5.451650] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x29)
[ 5.470354] platform reg-20-cs-dcdc2: Driver reg-20-cs-dcdc2 requests probe deferral
[ 5.479201] platform reg-20-cs-ldo1: Driver reg-20-cs-ldo1 requests probe deferral
[ 5.505136] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x29)
[ 5.528220] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[ 5.537420] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x29)
[ 5.570452] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[ 5.579146] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[ 5.587992] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x29)
[ 5.611599] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0xf)
[ 5.630560] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[ 5.639636] platform reg-20-cs-dcdc2: Driver reg-20-cs-dcdc2 requests probe deferral
[ 5.649103] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0xf)
[ 5.670262] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0xf)
[ 5.687033] platform reg-20-cs-dcdc3: Driver reg-20-cs-dcdc3 requests probe deferral
[ 5.701180] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0xf)
[ 5.730384] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0xf)
[ 5.760117] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x15)
[ 5.803254] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x15)
[ 5.849133] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x15)
[ 5.871914] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x15)
[ 5.900517] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x15)
[ 5.925941] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1e)
[ 5.950629] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1e)
[ 5.970814] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1e)
[ 6.001230] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1e)
[ 6.031382] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1e)
[ 6.060819] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1f)
[ 6.090813] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1f)
[ 6.120468] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1f)
[ 6.151855] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1f)
[ 6.180366] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1f)
[ 6.467768] �newcdr����: main entry
[ 6.477106] �newcdr����: [Firmware Version: zp@tiger_cdr 2016-10-30 23:56:11]
[ 6.490873] �newcdr����: ===no need to check battery capacity ===
[ 6.498417] [VFE]vfe_open
[ 6.504638] [VFE]..........................vfe clk open!.......................
[ 6.520847] [VFE]vfe_open ok
[ 6.524359] [VFE]vfe_close
[ 6.527467] [VFE]vfe select input flag = 0, s_input have not be used .
[ 6.534941] [VFE]..........................vfe clk close!.......................
[ 6.568023] [VFE]vfe_close end
[ 6.571801] [VFE]vfe_open
[ 6.574809] [VFE]..........................vfe clk open!.......................
[ 6.598990] [VFE]vfe_open ok
[ 6.602427] [VFE]vfe_close
[ 6.605527] [VFE]vfe select input flag = 0, s_input have not be used .
[ 6.613014] [VFE]..........................vfe clk close!.......................
[ 6.630280] [VFE]vfe_close end
[ 7.153973] [DISP] ready enter pm_runtime_get_sync, device0
[ 7.732116] [VFE]vfe_open
[ 7.735145] [VFE]..........................vfe clk open!.......................
[ 7.744046] [VFE]vfe_open ok
[ 7.747498] [VFE_WARN]NOT found this item: h22_mipi, you can add this sensor in the sensor_list_t!
[ 7.757872] [VFE_WARN]Not find this sensor info, Set vfe core clk = 500000000, after Set vfe core clk = 297000000
[ 7.779730] [VFE_ERR]sensor standby off error when selecting target device!
[ 7.787628] [VFE]vfe_close
[ 7.800971] [VFE_ERR]sensor power off error at device number when csi close!
[ 7.808914] [VFE]..........................vfe clk close!.......................
[ 7.817416] [VFE]vfe_close end
[ 7.823047] �newcdr����: startPreview finished
[ 8.268005] init: processing action 0x16c1d70 (property:sys.usb.config=mass_storage,adb)
[ 8.277649] adb_release
[ 8.281068] init: command 'write' r=0
[ 8.287865] adb_open
[ 8.295981] init: command 'write' r=0
[ 8.306075] init: command 'write' r=0
[ 8.316386] init: command 'write' r=0
[ 8.324215] ep_matches, wrn: endpoint already claimed, ep(0xc0482984, 0xc1907380, ep1in-bulk)
[ 8.334666] [VFE]vfe_open
[ 8.337811] [VFE]..........................vfe clk open!.......................
[ 8.346295] adb_bind_config
[ 8.349507] ep_matches, wrn: endpoint already claimed, ep(0xc0482984, 0xc1907380, ep1in-bulk)
[ 8.359197] ep_matches, wrn: endpoint already claimed, ep(0xc04829d0, 0xc1907380, ep1out-bulk)
[ 8.368870] ep_matches, wrn: endpoint already claimed, ep(0xc0482984, 0xc1907380, ep1in-bulk)
[ 8.378528] ep_matches, wrn: endpoint already claimed, ep(0xc04829d0, 0xc1907380, ep1out-bulk)
[ 8.388277] ep_matches, wrn: endpoint already claimed, ep(0xc0482a1c, 0xc1909300, ep2in-bulk)
[ 8.398489] [VFE]vfe_open ok
[ 8.401873] [VFE]vfe_close
[ 8.404989] [VFE]vfe select input flag = 0, s_input have not be used .
[ 8.412456] [VFE]..........................vfe clk close!.......................
[ 8.420983] init: command 'write' r=0
[ 8.425335] init: command 'setprop' r=0
[ 8.429777] [VFE]vfe_close end
[ 8.512590] init: waitpid returned pid 53, status = 00000000
[ 8.519344] init: process 'startupSound', pid 53 exited
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment