Created
October 23, 2019 18:47
-
-
Save JeremyGrosser/d89b1fb0bee50b02876d48af4b2af0a3 to your computer and use it in GitHub Desktop.
u-boot config for gameshell
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile | |
index 3b8dc2f56f..3150a68740 100644 | |
--- a/arch/arm/dts/Makefile | |
+++ b/arch/arm/dts/Makefile | |
@@ -485,7 +485,8 @@ dtb-$(CONFIG_MACH_SUN8I_A33) += \ | |
sun8i-a33-sinlinx-sina33.dtb \ | |
sun8i-r16-bananapi-m2m.dtb \ | |
sun8i-r16-nintendo-nes-classic-edition.dtb \ | |
- sun8i-r16-parrot.dtb | |
+ sun8i-r16-parrot.dtb \ | |
+ sun8i-r16-clockworkpi-cpi3.dtb | |
dtb-$(CONFIG_MACH_SUN8I_A83T) += \ | |
sun8i-a83t-allwinner-h8homlet-v2.dtb \ | |
sun8i-a83t-bananapi-m3.dtb \ | |
diff --git a/arch/arm/dts/sun8i-r16-clockworkpi-cpi3.dts b/arch/arm/dts/sun8i-r16-clockworkpi-cpi3.dts | |
new file mode 100644 | |
index 0000000000..d9b7529db7 | |
--- /dev/null | |
+++ b/arch/arm/dts/sun8i-r16-clockworkpi-cpi3.dts | |
@@ -0,0 +1,395 @@ | |
+/* | |
+ * Copyright (c) 2018 Clockwork | |
+ * | |
+ * This file is dual-licensed: you can use it either under the terms | |
+ * of the GPL or the X11 license, at your option. Note that this dual | |
+ * licensing only applies to this file, and not this project as a | |
+ * whole. | |
+ * | |
+ * a) This file is free software; you can redistribute it and/or | |
+ * modify it under the terms of the GNU General Public License as | |
+ * published by the Free Software Foundation; either version 2 of the | |
+ * License, or (at your option) any later version. | |
+ * | |
+ * This file is distributed in the hope that it will be useful, | |
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
+ * GNU General Public License for more details. | |
+ * | |
+ * Or, alternatively, | |
+ * | |
+ * b) Permission is hereby granted, free of charge, to any person | |
+ * obtaining a copy of this software and associated documentation | |
+ * files (the "Software"), to deal in the Software without | |
+ * restriction, including without limitation the rights to use, | |
+ * copy, modify, merge, publish, distribute, sublicense, and/or | |
+ * sell copies of the Software, and to permit persons to whom the | |
+ * Software is furnished to do so, subject to the following | |
+ * conditions: | |
+ * | |
+ * The above copyright notice and this permission notice shall be | |
+ * included in all copies or substantial portions of the Software. | |
+ * | |
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, | |
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES | |
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND | |
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT | |
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, | |
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING | |
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR | |
+ * OTHER DEALINGS IN THE SOFTWARE. | |
+ */ | |
+ | |
+/dts-v1/; | |
+#include "sun8i-a33.dtsi" | |
+#include "sunxi-common-regulators.dtsi" | |
+ | |
+#include <dt-bindings/gpio/gpio.h> | |
+#include <dt-bindings/input/input.h> | |
+ | |
+/ { | |
+ model = "Clockwork CPI3"; | |
+ compatible = "clockwork,clockworkpi-cpi3", "allwinner,sun8i-a33"; | |
+ | |
+ aliases { | |
+ serial0 = &uart0; | |
+ }; | |
+ | |
+ chosen { | |
+ stdout-path = "serial0:115200n8"; | |
+ }; | |
+ | |
+ leds { | |
+ compatible = "gpio-leds"; | |
+ pinctrl-names = "default"; | |
+ pinctrl-0 = <&led_pins>; | |
+ | |
+ led1 { | |
+ label = "led1"; | |
+ gpios = <&pio 1 7 GPIO_ACTIVE_LOW>; /* PB7 */ | |
+ }; | |
+ }; | |
+ | |
+ wifi_pwrseq: wifi_pwrseq { | |
+ compatible = "mmc-pwrseq-simple"; | |
+ reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */ | |
+ }; | |
+ | |
+ rfkill_gpio: rfkill_gpio { | |
+ compatible = "rfkill_gpio"; | |
+ type = "bluetooth"; | |
+ pinctrl-names = "default"; | |
+ pinctrl-0 = <&bt_control_pin>; | |
+ reset-gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ | |
+ shutdown-gpio = <&r_pio 0 10 GPIO_ACTIVE_LOW>; /* PL10 */ | |
+ }; | |
+ | |
+ backlight { | |
+ compatible = "ocp8178-backlight"; | |
+ pinctrl-names = "default"; | |
+ pinctrl-0 = <&backlight_control_pin>; | |
+ backlight-control-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ | |
+ default-brightness = <5>; | |
+ }; | |
+ | |
+ lcd { | |
+ compatible = "kd027-lcd"; | |
+ pinctrl-names = "default"; | |
+ pinctrl-0 = <&lcd_control_pin>; | |
+ lcd-rst-gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */ | |
+ lcd-cs-gpios = <&pio 2 3 GPIO_ACTIVE_HIGH>; /* PC3 */ | |
+ lcd-sck-gpios = <&pio 2 2 GPIO_ACTIVE_HIGH>; /* PC2 */ | |
+ lcd-sda-gpios = <&pio 2 0 GPIO_ACTIVE_HIGH>; /* PC0 */ | |
+ init-seq = /bits/ 8 <0x2b 0x01 0x00 0x07 0x0c 0x27 0x16 0x04>; | |
+ suspend-seq = /bits/ 8 <0x2b 0x00>; | |
+ resume-seq = /bits/ 8 <0x2b 0x01>; | |
+ }; | |
+ | |
+ panel { | |
+ compatible = "clockwork,cpi3-lcd"; | |
+ | |
+ ports { | |
+ #address-cells = <1>; | |
+ #size-cells = <0>; | |
+ port@0 { | |
+ #address-cells = <1>; | |
+ #size-cells = <0>; | |
+ reg = <0>; | |
+ | |
+ rgb_input: endpoint@0 { | |
+ reg = <0>; | |
+ remote-endpoint = <&tcon0_out_rgb>; | |
+ }; | |
+ }; | |
+ }; | |
+ }; | |
+}; | |
+ | |
+&codec { | |
+ status = "okay"; | |
+}; | |
+ | |
+&dai { | |
+ status = "okay"; | |
+}; | |
+ | |
+&sound { | |
+ status = "okay"; | |
+}; | |
+ | |
+&codec_analog { | |
+ pinctrl-names = "default"; | |
+ pinctrl-0 = <&speaker_amplifier_pin>; | |
+ speaker-amplifier-gpios = <&r_pio 0 3 GPIO_ACTIVE_HIGH>; /* PL3 */ | |
+ interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; | |
+}; | |
+ | |
+&de { | |
+ status = "okay"; | |
+}; | |
+ | |
+&tcon0 { | |
+ status = "okay"; | |
+}; | |
+ | |
+&tcon0_out { | |
+ tcon0_out_rgb: endpoint@0 { | |
+ reg = <0>; | |
+ remote-endpoint = <&rgb_input>; | |
+ }; | |
+}; | |
+ | |
+&ehci0 { | |
+ status = "okay"; | |
+}; | |
+ | |
+&mmc0 { | |
+ pinctrl-names = "default"; | |
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; | |
+ vmmc-supply = <®_dcdc1>; | |
+ cd-gpios = <&pio 1 3 GPIO_ACTIVE_LOW>; /* PD14 */ | |
+ bus-width = <4>; | |
+ status = "okay"; | |
+}; | |
+ | |
+&mmc1 { | |
+ pinctrl-names = "default"; | |
+ pinctrl-0 = <&mmc1_pins_a>, <&wifi_reset_pin>; | |
+ vmmc-supply = <®_aldo1>; | |
+ mmc-pwrseq = <&wifi_pwrseq>; | |
+ bus-width = <4>; | |
+ non-removable; | |
+ keep-power-in-suspend; | |
+ status = "okay"; | |
+}; | |
+ | |
+&ohci0 { | |
+ status = "okay"; | |
+}; | |
+ | |
+&pio { | |
+ mmc0_cd_pin: mmc0_cd_pin@0 { | |
+ pins = "PB3"; | |
+ function = "gpio_in"; | |
+ bias-pull-up; | |
+ }; | |
+ | |
+ led_pins: led_pins@0 { | |
+ pins = "PB7"; | |
+ function = "gpio_out"; | |
+ }; | |
+ | |
+ lcd_control_pin: lcd_control_pin@0 { | |
+ pins = "PB2", "PC0", "PC2", "PC3"; | |
+ function = "gpio_out"; | |
+ }; | |
+ | |
+ backlight_control_pin: backlight_control_pin@0 { | |
+ pins = "PH1"; | |
+ function = "gpio_out"; | |
+ }; | |
+}; | |
+ | |
+&r_pio { | |
+ usb1_vbus_pin: usb1_vbus_pin@0 { | |
+ pins = "PL2"; | |
+ function = "gpio_out"; | |
+ }; | |
+ | |
+ speaker_amplifier_pin: speaker_amplifier_pin@0 { | |
+ pins = "PL3"; | |
+ function = "gpio_out"; | |
+ }; | |
+ | |
+ usb0_id_det: usb0_id_detect_pin@0 { | |
+ pins = "PL4"; | |
+ function = "gpio_in"; | |
+ bias-pull-up; | |
+ }; | |
+ | |
+ wifi_reset_pin: wifi_reset_pin@0 { | |
+ pins = "PL6"; | |
+ function = "gpio_out"; | |
+ }; | |
+ | |
+ bt_control_pin: bt_control_pin@0 { | |
+ pins = "PL8", "PL10"; | |
+ function = "gpio_out"; | |
+ }; | |
+}; | |
+ | |
+&r_rsb { | |
+ status = "okay"; | |
+ | |
+ axp22x: pmic@3a3 { | |
+ compatible = "x-powers,axp223"; | |
+ reg = <0x3a3>; | |
+ interrupt-parent = <&nmi_intc>; | |
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>; | |
+ drivevbus-supply = <®_vcc5v0>; | |
+ x-powers,drive-vbus-en; | |
+ }; | |
+}; | |
+ | |
+#include "axp223.dtsi" | |
+ | |
+®_aldo1 { | |
+ regulator-always-on; | |
+ regulator-min-microvolt = <3000000>; | |
+ regulator-max-microvolt = <3000000>; | |
+ regulator-name = "vcc-io"; | |
+}; | |
+ | |
+®_aldo2 { | |
+ regulator-always-on; | |
+ regulator-min-microvolt = <2500000>; | |
+ regulator-max-microvolt = <2500000>; | |
+ regulator-name = "vdd-dll"; | |
+}; | |
+ | |
+®_aldo3 { | |
+ regulator-always-on; | |
+ regulator-min-microvolt = <3000000>; | |
+ regulator-max-microvolt = <3000000>; | |
+ regulator-name = "vcc-pll-avcc"; | |
+}; | |
+ | |
+®_dc5ldo { | |
+ regulator-always-on; | |
+ regulator-min-microvolt = <1100000>; | |
+ regulator-max-microvolt = <1100000>; | |
+ regulator-name = "vdd-cpus"; | |
+}; | |
+ | |
+®_dcdc1 { | |
+ regulator-always-on; | |
+ regulator-min-microvolt = <3000000>; | |
+ regulator-max-microvolt = <3000000>; | |
+ regulator-name = "vcc-3v0"; | |
+}; | |
+ | |
+®_dcdc2 { | |
+ regulator-always-on; | |
+ regulator-min-microvolt = <1100000>; | |
+ regulator-max-microvolt = <1100000>; | |
+ regulator-name = "vdd-sys"; | |
+}; | |
+ | |
+®_dcdc3 { | |
+ regulator-always-on; | |
+ regulator-min-microvolt = <1200000>; | |
+ regulator-max-microvolt = <1200000>; | |
+ regulator-name = "vdd-cpu"; | |
+}; | |
+ | |
+®_dcdc5 { | |
+ regulator-always-on; | |
+ regulator-min-microvolt = <1500000>; | |
+ regulator-max-microvolt = <1500000>; | |
+ regulator-name = "vcc-dram"; | |
+}; | |
+ | |
+®_dldo1 { | |
+ /* | |
+ * TODO: WiFi chip needs dldo1 AND dldo2 to be on to be powered. | |
+ * Remove next line once it is possible to sync two regulators. | |
+ */ | |
+ regulator-always-on; | |
+ regulator-min-microvolt = <3300000>; | |
+ regulator-max-microvolt = <3300000>; | |
+ regulator-name = "vcc-wifi0"; | |
+}; | |
+ | |
+®_dldo2 { | |
+ /* | |
+ * TODO: WiFi chip needs dldo1 AND dldo2 to be on to be powered. | |
+ * Remove next line once it is possible to sync two regulators. | |
+ */ | |
+ regulator-always-on; | |
+ regulator-min-microvolt = <3300000>; | |
+ regulator-max-microvolt = <3300000>; | |
+ regulator-name = "vcc-wifi1"; | |
+}; | |
+ | |
+®_dldo3 { | |
+ regulator-always-on; | |
+ regulator-min-microvolt = <3300000>; | |
+ regulator-max-microvolt = <3300000>; | |
+ regulator-name = "vcc-amp"; | |
+}; | |
+ | |
+®_dldo4 { | |
+ /* | |
+ * TODO: WiFi chip needs dldo1 AND dldo2 AND dldo4 to be on to be powered. | |
+ * Remove next line once it is possible to sync two regulators. | |
+ */ | |
+ regulator-always-on; | |
+ regulator-min-microvolt = <3300000>; | |
+ regulator-max-microvolt = <3300000>; | |
+ regulator-name = "vcc-wifi2"; | |
+}; | |
+ | |
+®_drivevbus { | |
+ regulator-name = "usb0-vbus"; | |
+ status = "okay"; | |
+}; | |
+ | |
+®_usb1_vbus { | |
+ pinctrl-names = "default"; | |
+ pinctrl-0 = <&usb1_vbus_pin>; | |
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */ | |
+ status = "okay"; | |
+}; | |
+ | |
+&battery_power_supply { | |
+ status = "okay"; | |
+}; | |
+ | |
+&uart0 { | |
+ status = "okay"; | |
+}; | |
+ | |
+&uart1 { | |
+ pinctrl-names = "default"; | |
+ pinctrl-0 = <&uart1_pins_a>, <&uart1_pins_cts_rts_a>; | |
+ status = "okay"; | |
+}; | |
+ | |
+&usb_otg { | |
+ dr_mode = "otg"; | |
+ status = "okay"; | |
+}; | |
+ | |
+&usb_power_supply { | |
+ status = "okay"; | |
+}; | |
+ | |
+&usbphy { | |
+ status = "okay"; | |
+ pinctrl-names = "default"; | |
+ pinctrl-0 = <&usb0_id_det>; | |
+ usb0_vbus-supply = <®_drivevbus>; | |
+ usb0_id_det-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */ | |
+ usb0_vbus_power-supply = <&usb_power_supply>; | |
+ usb1_vbus-supply = <®_usb1_vbus>; | |
+}; | |
diff --git a/configs/clockworkpi_cpi3_defconfig b/configs/clockworkpi_cpi3_defconfig | |
new file mode 100644 | |
index 0000000000..4defe9d88d | |
--- /dev/null | |
+++ b/configs/clockworkpi_cpi3_defconfig | |
@@ -0,0 +1,48 @@ | |
+CONFIG_ARM=y | |
+CONFIG_ARCH_SUNXI=y | |
+CONFIG_NR_DRAM_BANKS=1 | |
+CONFIG_DRAM_CLK=432 | |
+CONFIG_DRAM_ZQ=15291 | |
+CONFIG_DRAM_ODT_EN=y | |
+CONFIG_SPL=y | |
+CONFIG_SPL_TEXT_BASE=0x60 | |
+CONFIG_MACH_SUN8I_A33=y | |
+CONFIG_MMC0_CD_PIN="PB3" | |
+CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE" | |
+CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT" | |
+CONFIG_USB0_ID_DET="PL4" | |
+CONFIG_AXP_GPIO=y | |
+CONFIG_VIDEO_LCD_MODE="x:320,y:240,depth:18,pclk_khz:5800,le:60,ri:6,up:6,lo:2,hs:2,vs:2,sync:3,vmode:0" | |
+CONFIG_VIDEO_LCD_DCLK_PHASE=0 | |
+CONFIG_VIDEO_LCD_BL_PWM="PH1" | |
+CONFIG_VIDEO_LCD_RESET="PB2" | |
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set | |
+CONFIG_USE_PREBOOT=y | |
+# CONFIG_CMD_FLASH is not set | |
+# CONFIG_SPL_DOS_PARTITION is not set | |
+# CONFIG_SPL_PARTITION_UUIDS is not set | |
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-r16-clockworkpi-cpi3" | |
+CONFIG_FASTBOOT_CMD_OEM_FORMAT=y | |
+CONFIG_USB_EHCI_HCD=y | |
+CONFIG_USB_OHCI_HCD=y | |
+CONFIG_USB_MUSB_GADGET=y | |
+CONFIG_USB_FUNCTION_MASS_STORAGE=y | |
+CONFIG_SUNXI_DRAM_LPDDR3_STOCK=y | |
+CONFIG_SPLASH_SCREEN=y | |
+CONFIG_CMD_BMP=y | |
+CONFIG_AXP221_POWER=y | |
+CONFIG_AXP_DCDC1_VOLT=3000 | |
+CONFIG_AXP_DCDC2_VOLT=1100 | |
+CONFIG_AXP_DCDC3_VOLT=1200 | |
+CONFIG_AXP_DCDC4_VOLT=0 | |
+CONFIG_AXP_DCDC5_VOLT=1500 | |
+CONFIG_AXP_ALDO1_VOLT=3000 | |
+CONFIG_AXP_ALDO2_VOLT=2500 | |
+CONFIG_AXP_ALDO3_VOLT=3000 | |
+CONFIG_AXP_DLDO1_VOLT=3300 | |
+CONFIG_AXP_DLDO2_VOLT=3300 | |
+CONFIG_AXP_DLDO3_VOLT=3300 | |
+CONFIG_AXP_DLDO4_VOLT=3300 | |
+CONFIG_AXP_ELDO1_VOLT=0 | |
+CONFIG_AXP_ELDO2_VOLT=0 | |
+CONFIG_AXP_ELDO3_VOLT=0 |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment