Prestigio Multireader Stream PER5574BC

prestigio-per5574bc_defconfig

CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_SPL=y
CONFIG_MACH_SUN5I=y
CONFIG_DRAM_CLK=408
CONFIG_DRAM_EMR1=0
CONFIG_MMC0_CD_PIN="PG0"
CONFIG_USB0_VBUS_DET="PG1"
CONFIG_USB0_VBUS_PIN="PG12"
CONFIG_USB0_ID_DET="PG2"
CONFIG_AXP_GPIO=y
# CONFIG_VIDEO_HDMI is not set
CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:30000,le:45,ri:79,up:22,lo:13,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_POWER="AXP0-0"
CONFIG_VIDEO_LCD_BL_EN="AXP0-1"
CONFIG_VIDEO_LCD_BL_PWM="PB2"
CONFIG_NR_DRAM_BANKS=1
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL_I2C_SUPPORT=y
CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-prestigio-per5574bc"
CONFIG_CONS_INDEX=2
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_MUSB_HOST=y
CONFIG_USB_KEYBOARD=y
CONFIG_USB_STORAGE=y
CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y

script.fex

[product]
version = "1.0"
machine = "A13-EVB-V1.0"

[target]
boot_clock = 1008
dcdc2_vol = 1400
dcdc3_vol = 1200
ldo2_vol = 3000
ldo3_vol = 3300
ldo4_vol = 3300
pll4_freq = 960
pll6_freq = 720
power_start = 0
storage_type = 0

[card_boot]
logical_start = 40960
sprite_gpio0 =

[pm_para]
standby_mode = 0

[card_boot0_para]
card_ctrl = 0
card_high_speed = 1
card_line = 4
sdc_d1 = port:PF00<2><1><default><default>
sdc_d0 = port:PF01<2><1><default><default>
sdc_clk = port:PF02<2><1><default><default>
sdc_cmd = port:PF03<2><1><default><default>
sdc_d3 = port:PF04<2><1><default><default>
sdc_d2 = port:PF05<2><1><default><default>

[twi_para]
twi_port = 0
twi_scl = port:PB00<2><1><default><default>
twi_sda = port:PB01<2><1><default><default>

[uart_para]
uart_debug_port = 0
uart_debug_tx =
uart_debug_rx =

[uart_force_debug]
uart_debug_port = 0
uart_debug_tx = port:PF02<4><default><default><default>
uart_debug_rx = port:PF04<4><default><default><default>

[jtag_para]
jtag_enable = 0
jtag_ms = port:PF00<4><1><default><default>
jtag_ck = port:PF05<4><1><default><default>
jtag_do = port:PF03<4><1><default><default>
jtag_di = port:PF01<4><1><default><default>

[dram_para]
dram_baseaddr = 0x40000000
dram_clk = 408
dram_type = 3
dram_rank_num = 1
dram_chip_density = 2048
dram_io_width = 8
dram_bus_width = 16
dram_cas = 9
dram_zq = 0x7b
dram_odt_en = 0
dram_size = 512
dram_tpr0 = 0x42d899b7
dram_tpr1 = 0xa090
dram_tpr2 = 0x22a00
dram_tpr3 = 0x0
dram_tpr4 = 0x0
dram_tpr5 = 0x0
dram_emr1 = 0x0
dram_emr2 = 0x10
dram_emr3 = 0x0

[nand_para]
nand_used = 1
nand_we = port:PC00<2><default><default><default>
nand_ale = port:PC01<2><default><default><default>
nand_cle = port:PC02<2><default><default><default>
nand_ce1 = port:PC03<2><default><default><default>
nand_ce0 = port:PC04<2><default><default><default>
nand_nre = port:PC05<2><default><default><default>
nand_rb0 = port:PC06<2><default><default><default>
nand_rb1 = port:PC07<2><default><default><default>
nand_d0 = port:PC08<2><default><default><default>
nand_d1 = port:PC09<2><default><default><default>
nand_d2 = port:PC10<2><default><default><default>
nand_d3 = port:PC11<2><default><default><default>
nand_d4 = port:PC12<2><default><default><default>
nand_d5 = port:PC13<2><default><default><default>
nand_d6 = port:PC14<2><default><default><default>
nand_d7 = port:PC15<2><default><default><default>
nand_wp =
nand_ce2 =
nand_ce3 =
nand_ce4 =
nand_ce5 =
nand_ce6 =
nand_ce7 =
nand_spi =
nand_ndqs = port:PC19<2><default><default><default>
good_block_ratio = 0

[mali_para]
mali_used = 1
mali_clkdiv = 2

[twi0_para]
twi0_used = 1
twi0_scl = port:PB00<2><default><default><default>
twi0_sda = port:PB01<2><default><default><default>

[twi1_para]
twi1_used = 1
twi1_scl = port:PB15<2><default><default><default>
twi1_sda = port:PB16<2><default><default><default>

[twi2_para]
twi2_used = 1
twi2_scl = port:PB17<2><default><default><default>
twi2_sda = port:PB18<2><default><default><default>

[uart_para0]
uart_used = 0
uart_port = 0
uart_type = 2
uart_tx = port:PB19<2><1><default><default>
uart_rx = port:PB20<2><1><default><default>

[uart_para1]
uart_used = 0
uart_port = 1
uart_type = 2
uart_tx =
uart_rx =

[spi1_para]
spi_used = 0
spi_cs0 = port:PG09<2><default><default><default>
spi_cs1 = port:PG13<2><default><default><default>
spi_sclk = port:PG10<2><default><default><default>
spi_mosi = port:PG11<2><default><default><default>
spi_miso = port:PG12<2><default><default><default>

[spi2_para]
spi_used = 0
spi_cs0 = port:PE00<4><default><default><default>
spi_sclk = port:PE01<4><default><default><default>
spi_mosi = port:PB02<4><default><default><default>
spi_miso = port:PB03<4><default><default><default>

[rtp_para]
rtp_used = 0
rtp_screen_size = 5
rtp_regidity_level = 5
rtp_press_threshold_enable = 0
rtp_press_threshold = 0x1f40
rtp_sensitive_level = 0xf
rtp_exchange_x_y_flag = 0

[ctp_para]
ctp_used = 1
ctp_twi_id = 1
ctp_screen_max_x = 800
ctp_screen_max_y = 480
ctp_revert_x_flag = 0
ctp_revert_y_flag = 0
ctp_exchange_x_y_flag = 0
ctp_int_port = port:PG11<6><default><default><default>
ctp_wakeup = port:PB03<1><default><default><1>
ctp_io_port = port:PG11<0><default><default><default>

[tkey_para]
tkey_used = 0
tkey_name = "hv_keypad"
tkey_twi_id = 2
tkey_twi_addr = 0x62
tkey_int =

[motor_para]
motor_used = 0
motor_shake =

[disp_init]
disp_init_enable = 1
disp_mode = 0
screen0_output_type = 1
screen0_output_mode = 5
screen1_output_type = 1
screen1_output_mode = 5
fb0_framebuffer_num = 2
fb0_format = 10
fb0_pixel_sequence = 0
fb0_scaler_mode_enable = 0
fb1_framebuffer_num = 2
fb1_format = 10
fb1_pixel_sequence = 0
fb1_scaler_mode_enable = 0

[lcd0_para]
lcd_used = 1
lcd_x = 800
lcd_y = 480
lcd_dclk_freq = 30
lcd_pwm_not_used = 0
lcd_pwm_ch = 0
lcd_pwm_freq = 5000
lcd_pwm_pol = 1
lcd_if = 0
lcd_hbp = 46
lcd_ht = 925
lcd_vbp = 23
lcd_vt = 1032
lcd_hv_if = 0
lcd_hv_smode = 0
lcd_hv_s888_if = 0
lcd_hv_syuv_if = 0
lcd_hv_vspw = 0
lcd_hv_hspw = 0
lcd_lvds_ch = 0
lcd_lvds_mode = 0
lcd_lvds_bitwidth = 0
lcd_lvds_io_cross = 0
lcd_cpu_if = 0
lcd_frm = 1
lcd_io_cfg0 = 268435456
lcd_gamma_correction_en = 0
lcd_gamma_tbl_0 = 0x0
lcd_gamma_tbl_1 = 0x10101
lcd_gamma_tbl_255 = 0xffffff
lcd_bl_en_used = 1
lcd_bl_en = port:power1<1><0><default><1>
lcd_power_used = 1
lcd_power = port:power0<1><0><default><1>
lcd_pwm_used = 1
lcd_pwm = port:PB02<2><0><default><default>
lcd_gpio_0 =
lcd_gpio_1 =
lcd_gpio_2 =
lcd_gpio_3 =
lcdd0 = port:PD00<2><0><default><default>
lcdd1 = port:PD01<2><0><default><default>
lcdd2 = port:PD02<2><0><default><default>
lcdd3 = port:PD03<2><0><default><default>
lcdd4 = port:PD04<2><0><default><default>
lcdd5 = port:PD05<2><0><default><default>
lcdd6 = port:PD06<2><0><default><default>
lcdd7 = port:PD07<2><0><default><default>
lcdd8 = port:PD08<2><0><default><default>
lcdd9 = port:PD09<2><0><default><default>
lcdd10 = port:PD10<2><0><default><default>
lcdd11 = port:PD11<2><0><default><default>
lcdd12 = port:PD12<2><0><default><default>
lcdd13 = port:PD13<2><0><default><default>
lcdd14 = port:PD14<2><0><default><default>
lcdd15 = port:PD15<2><0><default><default>
lcdd16 = port:PD16<2><0><default><default>
lcdd17 = port:PD17<2><0><default><default>
lcdd18 = port:PD18<2><0><default><default>
lcdd19 = port:PD19<2><0><default><default>
lcdd20 = port:PD20<2><0><default><default>
lcdd21 = port:PD21<2><0><default><default>
lcdd22 = port:PD22<2><0><default><default>
lcdd23 = port:PD23<2><0><default><default>
lcdclk = port:PD24<2><0><default><default>
lcdde = port:PD25<2><0><default><default>
lcdhsync = port:PD26<2><0><default><default>
lcdvsync = port:PD27<2><0><default><default>

[tv_out_dac_para]
dac_used = 0
dac0_src = 0

[hdmi_para]
hdmi_used = 0

[csi0_para]
csi_used = 1
csi_mode = 0
csi_dev_qty = 1
csi_stby_mode = 1
csi_mname = "gc0308"
csi_twi_id = 2
csi_twi_addr = 0x42
csi_if = 0
csi_vflip = 0
csi_hflip = 0
csi_iovdd = ""
csi_avdd = ""
csi_dvdd = ""
csi_flash_pol = 1
csi_mname_b = "gt2005"
csi_twi_id_b = 2
csi_twi_addr_b = 0x78
csi_if_b = 0
csi_vflip_b = 0
csi_hflip_b = 0
csi_iovdd_b = ""
csi_avdd_b = ""
csi_dvdd_b = ""
csi_flash_pol_b = 1
csi_pck = port:PE00<3><default><default><default>
csi_ck = port:PE01<3><default><default><default>
csi_hsync = port:PE02<3><default><default><default>
csi_vsync = port:PE03<3><default><default><default>
csi_d0 = port:PE04<3><default><default><default>
csi_d1 = port:PE05<3><default><default><default>
csi_d2 = port:PE06<3><default><default><default>
csi_d3 = port:PE07<3><default><default><default>
csi_d4 = port:PE08<3><default><default><default>
csi_d5 = port:PE09<3><default><default><default>
csi_d6 = port:PE10<3><default><default><default>
csi_d7 = port:PE11<3><default><default><default>
csi_reset = port:power3<1><default><default><0>
csi_power_en = port:power2<1><default><default><1>
csi_stby = port:PG04<1><default><default><1>
csi_flash =
csi_af_en =
csi_reset_b =
csi_power_en_b =
csi_stby_b =
csi_flash_b =
csi_af_en_b =

[mmc0_para]
sdc_used = 1
sdc_detmode = 1
bus_width = 4
sdc_d1 = port:PF00<2><1><2><default>
sdc_d0 = port:PF01<2><1><2><default>
sdc_clk = port:PF02<2><1><2><default>
sdc_cmd = port:PF03<2><1><2><default>
sdc_d3 = port:PF04<2><1><2><default>
sdc_d2 = port:PF05<2><1><2><default>
sdc_det = port:PG00<0><1><default><default>
sdc_use_wp = 0
sdc_wp =

[mmc1_para]
sdc_used = 0
sdc_detmode =
bus_width =
sdc_cmd =
sdc_clk =
sdc_d0 =
sdc_d1 =
sdc_d2 =
sdc_d3 =
sdc_det =
sdc_use_wp =
sdc_wp =

[mmc2_para]
sdc_used = 0
sdc_detmode = 3
bus_width = 4
sdc_cmd = port:PE08<4><1><2><default>
sdc_clk = port:PE09<4><1><2><default>
sdc_d0 = port:PE04<4><1><2><default>
sdc_d1 = port:PE05<4><1><2><default>
sdc_d2 = port:PE06<4><1><2><default>
sdc_d3 = port:PE07<4><1><2><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =

[ms_para]
ms_used = 0
ms_bs =
ms_clk =
ms_d0 =
ms_d1 =
ms_d2 =
ms_d3 =
ms_det =

[keypad_para]
kp_used = 0
kp_in_size =
kp_out_size =
kp_in0 =
kp_in1 =
kp_in2 =
kp_in3 =
kp_in4 =
kp_in5 =
kp_in6 =
kp_in7 =
kp_out0 =
kp_out1 =
kp_out2 =
kp_out3 =
kp_out4 =
kp_out5 =
kp_out6 =
kp_out7 =

[usbc0]
usb_used = 1
usb_port_type = 2
usb_detect_type = 1
usb_id_gpio = port:PG02<0><1><default><default>
usb_det_vbus_gpio = port:PG01<0><0><default><default>
usb_drv_vbus_gpio = port:PG12<1><0><default><0>
usb_host_init_state = 0

[usbc1]
usb_used = 1
usb_port_type = 1
usb_detect_type = 0
usb_controller_type = 0
usb_id_gpio =
usb_det_vbus_gpio =
usb_drv_vbus_gpio = port:power203<1><default><default><0>
usb_host_init_state = 1

[port_pm]
restrict_1a = 1
restrict_500ma = 1
v_1a = 3630000
c_1a = 5
v_500ma = 3440000
c_500ma = 5
v_disable = 3250000
c_disable = 5
ctrl_gpio = port:PF04<1><0><default><0>

[usb_feature]
vendor_id = 6353
mass_storage_id = 1
adb_id = 2
manufacturer_name = "USB Developer"
product_name = "Android"
serial_number = "20080411"

[msc_feature]
vendor_name = "USB 2.0"
product_name = "USB Flash Driver"
release = 100
luns = 2

[gsensor_para]
gsensor_used = 1
gsensor_name = "dmardxx"
gsensor_twi_id = 1
gsensor_twi_addr = 0x1c
gsensor_int1 =
gsensor_int2 =

[gps_para]
gps_used = 0
gps_spi_id =
gps_spi_cs_num =
gps_lradc =
gps_clk =
gps_sign =
gps_mag =
gps_vcc_en =
gps_osc_en =
gps_rx_en =

[sdio_wifi_para]
sdio_wifi_used = 0
sdio_wifi_sdc_id =
sdio_wifi_mod_sel =

[usb_wifi_para]
usb_wifi_used = 1
usb_wifi_usbc_num = 1

[3g_para]
3g_used = 0
3g_name =
3g_usbc_num =
3g_on_off =
3g_reset =
3g_poweron =
3g_wakeup_out =
3g_wakeup_in =

[gy_para]
gy_used = 0
gy_twi_id = 1
gy_twi_addr = 0
gy_int1 =
gy_int2 =

[ls_para]
ls_used = 0
ls_name = "ltr501als"
ls_twi_id = 1
ls_twi_addr =
ls_int =

[compass_para]
compass_used = 0
compass_twi_id =
compass_twi_addr =
compass_int =

[bt_para]
bt_used = 0
bt_uart_id =
bt_mod_type =

[i2s_para]
i2s_used = 0
i2s_channel =
i2s_mclk =
i2s_bclk =
i2s_lrclk =
i2s_dout0 =
i2s_dout1 =
i2s_dout2 =
i2s_dout3 =
i2s_din =

[spdif_para]
spdif_used = 0
spdif_mclk =
spdif_dout =
spdif_din =

[audio_para]
audio_used = 1
capture_used = 1
audio_lr_change = 0
audio_pa_ctrl = port:PG10<1><default><default><0>

[ir_para]
ir_used = 0
ir0_rx = port:PB04<2><default><default><default>

[rtc_para]
rtc_used = 1
rtc_name = "pcf8563"
rtc_twi_id = 1
rtc_twi_addr = 81

[pmu_para]
pmu_used = 1
pmu_twi_addr = 52
pmu_twi_id = 0
pmu_irq_id = 0
pmu_battery_rdc = 100
pmu_battery_cap = 3000
pmu_init_chgcur = 300
pmu_earlysuspend_chgcur = 800
pmu_suspend_chgcur = 1000
pmu_resume_chgcur = 300
pmu_shutdown_chgcur = 1000
pmu_init_chgvol = 4200
pmu_init_chgend_rate = 15
pmu_init_chg_enabled = 1
pmu_init_adc_freq = 100
pmu_init_adc_freqc = 100
pmu_init_chg_pretime = 50
pmu_init_chg_csttime = 720
pmu_bat_para1 = 0
pmu_bat_para2 = 0
pmu_bat_para3 = 0
pmu_bat_para4 = 3
pmu_bat_para5 = 4
pmu_bat_para6 = 5
pmu_bat_para7 = 7
pmu_bat_para8 = 13
pmu_bat_para9 = 20
pmu_bat_para10 = 29
pmu_bat_para11 = 43
pmu_bat_para12 = 48
pmu_bat_para13 = 63
pmu_bat_para14 = 75
pmu_bat_para15 = 85
pmu_bat_para16 = 100
pmu_usbvol_limit = 1
pmu_usbcur_limit = 0
pmu_usbvol = 4000
pmu_usbcur = 0
pmu_usbvol_pc = 4000
pmu_usbcur_pc = 0
pmu_pwroff_vol = 2900
pmu_pwron_vol = 2900
pmu_pekoff_time = 6000
pmu_pekoff_en = 1
pmu_peklong_time = 1500
pmu_pekon_time = 1000
pmu_pwrok_time = 64
pmu_pwrnoe_time = 128
pmu_intotp_en = 1
pmu_used2 = 0
pmu_adpdet =
pmu_init_chgcur2 = 400
pmu_earlysuspend_chgcur2 = 600
pmu_suspend_chgcur2 = 1200
pmu_resume_chgcur2 = 400
pmu_shutdown_chgcur2 = 1200
pmu_suspendpwroff_vol = 3500
pmu_batdeten = 1

[recovery_key]
key_min = 4
key_max = 6

[dvfs_table]
max_freq = 1008000000
min_freq = 60000000
LV_count = 7
LV1_freq = 1104000000
LV1_volt = 1500
LV2_freq = 1008000000
LV2_volt = 1400
LV3_freq = 912000000
LV3_volt = 1350
LV4_freq = 864000000
LV4_volt = 1300
LV5_freq = 624000000
LV5_volt = 1200
LV6_freq = 576000000
LV6_volt = 1200
LV7_freq = 432000000
LV7_volt = 1200

sun5i-a13-prestigio-per5574bc.dts

/*
 * Copyright 2018 Jacek Pruciak <juniorjpdj@juniorjpdj.pl>
 *
 * This file is dual-licensed: you can use it either under the terms
 * of the GPL or the X11 license, at your option. Note that this dual
 * licensing only applies to this file, and not this project as a
 * whole.
 *
 *  a) This file is free software; you can redistribute it and/or
 *     modify it under the terms of the GNU General Public License as
 *     published by the Free Software Foundation; either version 2 of the
 *     License, or (at your option) any later version.
 *
 *     This file is distributed in the hope that it will be useful,
 *     but WITHOUT ANY WARRANTY; without even the implied warranty of
 *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *     GNU General Public License for more details.
 *
 * Or, alternatively,
 *
 *  b) Permission is hereby granted, free of charge, to any person
 *     obtaining a copy of this software and associated documentation
 *     files (the "Software"), to deal in the Software without
 *     restriction, including without limitation the rights to use,
 *     copy, modify, merge, publish, distribute, sublicense, and/or
 *     sell copies of the Software, and to permit persons to whom the
 *     Software is furnished to do so, subject to the following
 *     conditions:
 *
 *     The above copyright notice and this permission notice shall be
 *     included in all copies or substantial portions of the Software.
 *
 *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
 *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
 *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
 *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
 *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
 *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
 *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
 *     OTHER DEALINGS IN THE SOFTWARE.
 */

/dts-v1/;
#include "sun5i-a13.dtsi"
#include "sun5i-reference-design-tablet.dtsi"

/ {
	model = "Prestigio Multireader Stream PER5574BC";
	compatible = "prestigio,per5574bc", "allwinner,sun5i-a13";
};

&usb0_vbus_detect_pin {
	allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};

&usb_otg {
	dr_mode = "host";
};