openwrt dmesg

[    0.000000] Linux version 4.14.167 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10911-c155900f66)) #0 SMP Wed Jan 29 16:05:35 2020
[    0.000000] Skipping L2 locking due to reduced L2 cache size
[    0.000000] CVMSEG size: 2 cache lines (256 bytes)
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 000d9301 (Cavium Octeon II)
[    0.000000] Checking for the multiply/shift bug... no.
[    0.000000] Checking for the daddiu bug... no.
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 000000000c800000 @ 0000000002900000 (usable)
[    0.000000]  memory: 0000000000c00000 @ 000000000f200000 (usable)
[    0.000000]  memory: 000000006f800000 @ 0000000020000000 (usable)
[    0.000000]  memory: 00000000017ea220 @ 0000000001100000 (usable)
[    0.000000] Wasting 243712 bytes for tracking 4352 unused pages
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Using passed Device Tree.
[    0.000000] software IO TLB: mapped [mem 0x0291f000-0x0295f000] (0MB)
[    0.000000] Primary instruction cache 37kB, virtually tagged, 37 way, 8 sets, linesize 128 bytes.
[    0.000000] Primary data cache 32kB, 32-way, 8 sets, linesize 128 bytes.
[    0.000000] Zone ranges:
[    0.000000]   DMA32    [mem 0x0000000000000000-0x00000000efffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x00000000028e9fff]
[    0.000000]   node   0: [mem 0x0000000002900000-0x000000000f0fffff]
[    0.000000]   node   0: [mem 0x000000000f200000-0x000000000fdfffff]
[    0.000000]   node   0: [mem 0x0000000020000000-0x000000008f7fffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000008f7fffff]
[    0.000000] On node 0 totalpages: 521450
[    0.000000]   DMA32 zone: 7130 pages used for memmap
[    0.000000]   DMA32 zone: 0 pages reserved
[    0.000000]   DMA32 zone: 521450 pages, LIFO batch:31
[    0.000000] random: get_random_bytes called from 0xffffffff817586d8 with crng_init=0
[    0.000000] percpu: Embedded 18 pages/cpu s35632 r8192 d29904 u73728
[    0.000000] pcpu-alloc: s35632 r8192 d29904 u73728 alloc=18*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 514320
[    0.000000] Kernel command line: mtdparts=phys_mapped_flash:640k(boot0)ro,640k(boot1)ro,64k(eeprom)ro root=/dev/mmcblk0p2 rootfstype=squashfs,ext4 rootwait  console=ttyS0,115200
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] Memory: 2011608K/2085800K available (5331K kernel code, 343K rwdata, 808K rodata, 1312K init, 16680K bss, 74192K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	CONFIG_RCU_FANOUT set to non-default value of 32
[    0.000000] 	RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 127
[    5.122330] clocksource: OCTEON_CVMCOUNT: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns
[    5.133254] Calibrating delay loop (skipped) preset value.. 2000.00 BogoMIPS (lpj=4000000)
[    5.141498] pid_max: default: 32768 minimum: 301
[    5.146165] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    5.152792] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    5.160274] Checking for the daddi bug... no.
[    5.164897] Hierarchical SRCU implementation.
[    5.169442] smp: Bringing up secondary CPUs ...
[    5.174082] SMP: Booting CPU01 (CoreId  1)...
[    5.178355] CPU1 revision is: 000d9301 (Cavium Octeon II)
[    5.178446] smp: Brought up 1 node, 2 CPUs
[    5.189971] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    5.199575] futex hash table entries: 512 (order: 4, 65536 bytes)
[    5.205985] NET: Registered protocol family 16
[    5.214821] PCIe: Port 0 in endpoint mode, skipping.
[    5.219639] PCIe: Initializing port 1
[    5.234275] PCIe: Port 1 stuck in reset, skipping.
[    5.244724] SCSI subsystem initialized
[    5.248506] usbcore: registered new interface driver usbfs
[    5.253897] usbcore: registered new interface driver hub
[    5.259178] usbcore: registered new device driver usb
[    5.264331] PCI host bridge to bus 0000:00
[    5.268275] pci_bus 0000:00: root bus resource [mem 0x1000000000000]
[    5.274611] pci_bus 0000:00: root bus resource [io  0x0000]
[    5.280179] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    5.286956] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    5.294897] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    5.295595] clocksource: Switched to clocksource OCTEON_CVMCOUNT
[    5.301957] NET: Registered protocol family 2
[    5.306667] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    5.313900] TCP bind hash table entries: 16384 (order: 7, 524288 bytes)
[    5.320674] TCP: Hash tables configured (established 16384 bind 16384)
[    5.327124] UDP hash table entries: 1024 (order: 4, 98304 bytes)
[    5.333107] UDP-Lite hash table entries: 1024 (order: 4, 98304 bytes)
[    5.339653] NET: Registered protocol family 1
[    5.343872] PCI: CLS 0 bytes, default 128
[    5.344666] Crashlog allocated RAM at address 0x3f00000
[    5.349978] workingset: timestamp_bits=62 max_order=19 bucket_order=0
[    5.359656] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    5.365471] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    5.376723] io scheduler noop registered
[    5.380499] io scheduler deadline registered (default)
[    5.385865] octeon_gpio 1070000000800.gpio-controller: OCTEON GPIO driver probed.
[    5.393375] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    5.400704] random: fast init done
[    5.400904] console [ttyS0] disabled
[    5.407528] 1180000000800.serial: ttyS0 at MMIO 0x1180000000800 (irq = 34, base_baud = 37500000) is a OCTEON
[    5.417357] console [ttyS0] enabled
[    5.424302] bootconsole [early0] disabled
[    5.432526] 1180000000c00.serial: ttyS1 at MMIO 0x1180000000c00 (irq = 35, base_baud = 37500000) is a OCTEON
[    5.442620] octeon_rng octeon_rng: Octeon Random Number Generator
[    5.451324] loop: module loaded
[    5.454877] of-flash 1f400000.nor: Can't get bank width from device tree
[    5.461758] libphy: mdio_octeon: probed
[    5.467027] mdio_octeon 1180000001800.mdio: Probed
[    5.471945] libphy: mdio_octeon: probed
[    5.476317] mdio_octeon 1180000001900.mdio: Probed
[    5.481322] libphy: Fixed MDIO Bus: probed
[    5.485531] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.492084] ehci-pci: EHCI PCI platform driver
[    5.496586] ehci-platform: EHCI generic platform driver
[    5.501954] ehci-platform 16f0000000000.ehci: EHCI Host Controller
[    5.508178] ehci-platform 16f0000000000.ehci: new USB bus registered, assigned bus number 1
[    5.516628] ehci-platform 16f0000000000.ehci: irq 56, io mem 0x16f0000000000
[    5.539615] ehci-platform 16f0000000000.ehci: USB 2.0 started, EHCI 1.00
[    5.546741] hub 1-0:1.0: USB hub found
[    5.550542] hub 1-0:1.0: 2 ports detected
[    5.554852] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    5.561076] ohci-platform: OHCI generic platform driver
[    5.566428] ohci-platform 16f0000000400.ohci: Generic Platform OHCI controller
[    5.573691] ohci-platform 16f0000000400.ohci: new USB bus registered, assigned bus number 2
[    5.582116] ohci-platform 16f0000000400.ohci: irq 56, io mem 0x16f0000000400
[    5.651975] hub 2-0:1.0: USB hub found
[    5.655842] hub 2-0:1.0: 2 ports detected
[    5.660227] usbcore: registered new interface driver usb-storage
[    5.666287] octeon_wdt: Initial granularity 5 Sec
[    5.712957] Interface 0 has 4 ports (SGMII)
[    5.717209] Interface 1 has 4 ports (SGMII)
[    5.724743] NET: Registered protocol family 10
[    5.730649] Segment Routing with IPv6
[    5.734397] NET: Registered protocol family 17
[    5.738893] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    5.751881] 8021q: 802.1Q VLAN Support v1.8
[    5.756236] Bootbus flash: Setting flash for 8MB flash at 0x1f400000
[    5.887608] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    6.140602] usb-storage 1-1:1.0: USB Mass Storage device detected
[    6.146913] scsi host0: usb-storage 1-1:1.0
[    7.181685] scsi 0:0:0:0: Direct-Access              USB Flash Drive  8.07 PQ: 0 ANSI: 2
[    7.191412] sd 0:0:0:0: [sda] 7987200 512-byte logical blocks: (4.09 GB/3.81 GiB)
[    7.199905] sd 0:0:0:0: [sda] Write Protect is off
[    7.204723] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[    7.205781] sd 0:0:0:0: [sda] No Caching mode page found
[    7.211121] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    7.431076] phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0000c9
[    7.441459] Amd/Fujitsu Extended Query Table at 0x0040
[    7.446635]   Amd/Fujitsu Extended Query version 1.1.
[    7.451707] phys_mapped_flash: Swapping erase regions for top-boot CFI table.
[    7.458864] number of CFI chips: 1
[    7.462293] 3 cmdlinepart partitions found on MTD device phys_mapped_flash
[    7.469190] Creating 3 MTD partitions on "phys_mapped_flash":
[    7.474958] 0x000000000000-0x0000000a0000 : "boot0"
[    7.480244] 0x0000000a0000-0x000000140000 : "boot1"
[    7.485521] 0x000000140000-0x000000150000 : "eeprom"
[    7.493340] OF: fdt: not creating '/sys/firmware/fdt': CRC check failed
[    7.724323]  sda: sda1
[    7.729796] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    7.735379] Waiting for root device /dev/mmcblk0p2...
[   15.183325] mmc0: new DDR MMC card at address 0001
[   15.188347] mmcblk0: mmc0:0001 SEM04G 3.69 GiB 
[   15.192999] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB
[   15.199040] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB
[   15.205037] mmcblk0rpmb: mmc0:0001 SEM04G partition 3 2.00 MiB, chardev (252:0)
[   15.213001]  mmcblk0: p1 p2
[   15.230178] VFS: Mounted root (squashfs filesystem) readonly on device 179:2.
[   15.237810] Freeing unused kernel memory: 1312K
[   15.242375] This architecture does not have kernel memory protection.
[   15.632611] init: Console is alive
[   15.636151] init: - watchdog -
[   15.813531] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[   15.820464] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[   15.830878] init: - preinit -
[   16.286650] random: jshn: uninitialized urandom read (4 bytes read)
[   16.311988] random: jshn: uninitialized urandom read (4 bytes read)
[   16.331100] random: jshn: uninitialized urandom read (4 bytes read)
[   16.359095] eth0: 1000 Mbps Full duplex, port 16, queue 16
[   16.364715] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   17.355788] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   19.496281] mount_root: rootdisk overlay filesystem has not been formatted yet
[   19.680751] urandom_read: 1 callbacks suppressed
[   19.680756] random: mkfs.f2fs: uninitialized urandom read (16 bytes read)
[   19.692347] print_req_error: I/O error, dev loop0, sector 0
[   19.886405] random: crng init done
[   34.909340] F2FS-fs (loop0): Found nat_bits in checkpoint
[   34.981809] F2FS-fs (loop0): Mounted with checkpoint version = 3e14b327
[   34.988869] mount_root: overlay filesystem has not been fully initialized yet
[   34.996268] mount_root: switching to f2fs overlay
[   35.037412] urandom-seed: Seed file not found (/etc/urandom.seed)
[   35.126750] eth0: Link down
[   35.133336] procd: - early -
[   35.136287] procd: - watchdog -
[   35.724400] procd: - watchdog -
[   35.727761] procd: - ubus -
[   35.802075] procd: - init -
[   35.984259] kmodloader: loading kernel modules from /etc/modules.d/*
[   36.014009] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   36.017147] urngd: v1.0.2 started.
[   36.022652] ip_tables: (C) 2000-2006 Netfilter Core Team
[   36.031187] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[   36.054205] xt_time: kernel timezone is -0000
[   36.062105] PPP generic driver version 2.4.2
[   36.067558] NET: Registered protocol family 24
[   36.073294] kmodloader: done loading kernel modules from /etc/modules.d/*
[   42.073020] br-lan: port 1(eth0) entered blocking state
[   42.078295] br-lan: port 1(eth0) entered disabled state
[   42.083748] device eth0 entered promiscuous mode
[   42.104397] br-lan: port 1(eth0) entered blocking state
[   42.109666] br-lan: port 1(eth0) entered forwarding state
[   42.115202] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   42.136371] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   43.087976] br-lan: port 1(eth0) entered disabled state
[   46.165776] eth0: 1000 Mbps Full duplex, port 16, queue 16
[   46.171306] br-lan: port 1(eth0) entered blocking state
[   46.176559] br-lan: port 1(eth0) entered forwarding state
[   46.182870] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   79.961751] eth0: Link down
[   79.964785] br-lan: port 1(eth0) entered disabled state
[   84.053770] eth0: 1000 Mbps Full duplex, port 16, queue 16
[   84.059288] br-lan: port 1(eth0) entered blocking state
[   84.064539] br-lan: port 1(eth0) entered forwarding state
[  108.629750] eth0: Link down
[  108.632775] br-lan: port 1(eth0) entered disabled state
[  111.769776] eth1: 1000 Mbps Full duplex, port 17, queue 17
[  111.775303] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[  123.033749] eth1: Link down
[  125.013811] eth0: 1000 Mbps Full duplex, port 16, queue 16
[  125.019377] br-lan: port 1(eth0) entered blocking state
[  125.024636] br-lan: port 1(eth0) entered forwarding state
[  272.958271] br-lan: port 2(eth6) entered blocking state
[  272.963543] br-lan: port 2(eth6) entered disabled state
[  272.968947] device eth6 entered promiscuous mode
[  272.975612] br-lan: port 3(eth7) entered blocking state
[  272.980868] br-lan: port 3(eth7) entered disabled state
[  272.986254] device eth7 entered promiscuous mode
[  272.990958] br-lan: port 3(eth7) entered blocking state
[  272.996208] br-lan: port 3(eth7) entered forwarding state
[  273.008914] br-lan: port 3(eth7) entered disabled state
[  273.014212] br-lan: port 1(eth0) entered disabled state
[  273.031024] device eth0 left promiscuous mode
[  273.035478] br-lan: port 1(eth0) entered disabled state
[  273.058911] eth0: Link down
[  273.073278] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[  273.079211] device eth6 left promiscuous mode
[  273.083656] br-lan: port 2(eth6) entered disabled state
[  273.115197] IPv6: ADDRCONF(NETDEV_UP): eth6: link is not ready
[  273.121104] device eth7 left promiscuous mode
[  273.125537] br-lan: port 3(eth7) entered disabled state
[  273.155122] IPv6: ADDRCONF(NETDEV_UP): eth7: link is not ready
[  273.194619] br-lan: port 1(eth0) entered blocking state
[  273.199888] br-lan: port 1(eth0) entered disabled state
[  273.205363] device eth0 entered promiscuous mode
[  273.211486] br-lan: port 2(eth6) entered blocking state
[  273.216762] br-lan: port 2(eth6) entered disabled state
[  273.223737] device eth6 entered promiscuous mode
[  273.230142] br-lan: port 3(eth7) entered blocking state
[  273.235413] br-lan: port 3(eth7) entered disabled state
[  273.241949] device eth7 entered promiscuous mode
[  273.247843] br-lan: port 3(eth7) entered blocking state
[  273.253103] br-lan: port 3(eth7) entered forwarding state
[  273.258572] br-lan: port 1(eth0) entered blocking state
[  273.263826] br-lan: port 1(eth0) entered forwarding state
[  273.963878] br-lan: port 3(eth7) entered disabled state
[  273.969644] br-lan: port 1(eth0) entered disabled state
[  277.305777] eth0: 1000 Mbps Full duplex, port 16, queue 16
[  277.311439] br-lan: port 1(eth0) entered blocking state
[  277.316691] br-lan: port 1(eth0) entered forwarding state
[  468.117777] eth1: 1000 Mbps Full duplex, port 17, queue 17
[  468.192532] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[  468.200922] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[  562.260620] pppoe-wan: renamed from ppp0
[ 1172.278596] eth6: 1000 Mbps Full duplex, port 2, queue 2
[ 1172.283953] br-lan: port 2(eth6) entered blocking state
[ 1172.289207] br-lan: port 2(eth6) entered forwarding state
[ 1359.476774] kmodloader: loading kernel modules from /etc/modules.d/*
[ 1359.484248] tun: Universal TUN/TAP device driver, 1.6
[ 1359.490044] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 1450.799987] eth0: Link down
[ 1450.803503] br-lan: port 1(eth0) entered disabled state
[ 1458.995942] eth0: 1000 Mbps Full duplex, port 16, queue 16
[ 1459.001625] br-lan: port 1(eth0) entered blocking state
[ 1459.006880] br-lan: port 1(eth0) entered forwarding state
[ 1464.116002] eth0: Link down
[ 1464.119050] br-lan: port 1(eth0) entered disabled state
[ 2683.684021] eth6: Link down
[ 2683.687147] br-lan: port 2(eth6) entered disabled state
[ 2692.899833] eth6: 1000 Mbps Full duplex, port 2, queue 2
[ 2692.905321] br-lan: port 2(eth6) entered blocking state
[ 2692.910573] br-lan: port 2(eth6) entered forwarding state
[ 2708.259801] eth6: Link down
[ 2708.262831] br-lan: port 2(eth6) entered disabled state
[ 2710.307807] eth6: 1000 Mbps Full duplex, port 2, queue 2
[ 2710.313155] br-lan: port 2(eth6) entered blocking state
[ 2710.318409] br-lan: port 2(eth6) entered forwarding state
[ 2729.763499] eth6: Link down
[ 2729.766666] br-lan: port 2(eth6) entered disabled state
[ 2733.859498] eth6: 1000 Mbps Full duplex, port 2, queue 2
[ 2733.864984] br-lan: port 2(eth6) entered blocking state
[ 2733.870237] br-lan: port 2(eth6) entered forwarding state
[ 2738.979578] eth6: Link down
[ 2738.982616] br-lan: port 2(eth6) entered disabled state
[ 2740.007477] eth6: 1000 Mbps Full duplex, port 2, queue 2
[ 2740.013839] br-lan: port 2(eth6) entered blocking state
[ 2740.024475] br-lan: port 2(eth6) entered forwarding state
[ 2743.075560] eth6: Link down
[ 2743.078597] br-lan: port 2(eth6) entered disabled state
[ 2745.127566] eth6: 1000 Mbps Full duplex, port 2, queue 2
[ 2745.132936] br-lan: port 2(eth6) entered blocking state
[ 2745.138190] br-lan: port 2(eth6) entered forwarding state
[ 2754.343352] eth6: Link down
[ 2754.346545] br-lan: port 2(eth6) entered disabled state
[ 2795.299141] eth6: 1000 Mbps Full duplex, port 2, queue 2
[ 2795.304639] br-lan: port 2(eth6) entered blocking state
[ 2795.309893] br-lan: port 2(eth6) entered forwarding state
[80715.867606] usb 1-1: USB disconnect, device number 2
[86967.303181] pppoe-wan: renamed from ppp0
[173372.145074] pppoe-wan: renamed from ppp0
[259777.055363] pppoe-wan: renamed from ppp0
[346182.044233] pppoe-wan: renamed from ppp0
[422313.743022] device tun0 entered promiscuous mode
[422330.346105] device tun0 left promiscuous mode
[432586.944487] pppoe-wan: renamed from ppp0
[518991.842237] pppoe-wan: renamed from ppp0
[605396.856815] pppoe-wan: renamed from ppp0
[691801.840896] pppoe-wan: renamed from ppp0
[778206.787410] pppoe-wan: renamed from ppp0
[864611.654946] pppoe-wan: renamed from ppp0
[951026.783735] pppoe-wan: renamed from ppp0
[1037431.619417] pppoe-wan: renamed from ppp0
[1090850.487614] eth6: Link down
[1090850.490913] br-lan: port 2(eth6) entered disabled state
[1090851.511501] eth6: 1000 Mbps Full duplex, port 2, queue 2
[1090851.517469] br-lan: port 2(eth6) entered blocking state
[1090851.522892] br-lan: port 2(eth6) entered forwarding state
[1111302.268297] br-lan: port 3(eth7) entered disabled state