Landrash

#include <IRremote.h>

/*

 Send infrared commands from the Arduino to the iRobot Roomba
 by probono
 
 2013-03-17 Initial release
 

Landrash

/*--------------------------------------------------------------
  Program:      eth_websrv_LED

  Description:  Arduino web server that serves up a web page
                allowing the user to control an LED
  
  Hardware:     - Arduino Uno and official Arduino Ethernet
                  shield. Should work with other Arduinos and
                  compatible Ethernet shields.
                - LED and resistor in series connected between

Landrash

#!/bin/bash

# set -e

PROGRAMNAME=test
VERSION=0.1
ARCH=amd64
OUTPUT_FILENAME="${PROGRAMNAME}_${VERSION}_${ARCH}.deb"

echo "creating deb for '${PROGRAMNAME}'; output '${OUTPUT_FILENAME}'"

Landrash

#!/bin/bash

echo
echo "Homebridge install script for Hassbian"
echo

if [ "$(id -u)" != "0" ]; then
   echo "This script must be run with sudo. Use \"sudo ${0} ${*}\"" 1>&2
   exit 1
fi

Landrash

WannaCry|WannaDecrypt0r NSA-Cyberweapon-Powered Ransomware Worm

• Virus Name: WannaCrypt, WannaCry, WanaCrypt0r, WCrypt, WCRY
• Vector: All Windows versions before Windows 10 are vulnerable if not patched for MS-17-010. It uses EternalBlue MS17-010 to propagate.
• Ransom: between $300 to $600. There is code to 'rm' (delete) files in the virus. Seems to reset if the virus crashes.
• Backdooring: The worm loops through every RDP session on a system to run the ransomware as that user. It also installs the DOUBLEPULSAR backdoor. It corrupts shadow volumes to make recovery harder. (source: malwarebytes)
• Kill switch: If the website www.iuqerfsodp9ifjaposdfjhgosurijfaewrwergwea.com is up the virus exits instead of infecting the host. (source: malwarebytes). This domain has been sinkholed, stopping the spread of the worm.

SECURITY BULLETIN AND UPDATES HERE: https://technet.microsoft.com/en-us/library/security/ms17-010.aspx

Landrash

Raspberry Pi Zero OTG Mode

Simple guide for setting up OTG modes on the Raspberry Pi Zero - By Andrew Mulholland (gbaman).

The Raspberry Pi Zero (and model A and A+) support USB On The Go, given the processor is connected directly to the USB port, unlike on the B, B+ or Pi 2 B, which goes via a USB hub.
Because of this, if setup to, the Pi can act as a USB slave instead, providing virtual serial (a terminal), virtual ethernet, virtual mass storage device (pendrive) or even other virtual devices like HID, MIDI, or act as a virtual webcam!
It is important to note that, although the model A and A+ can support being a USB slave, they are missing the ID pin (is tied to ground internally) so are unable to dynamically switch between USB master/slave mode. As such, they default to USB master mode. There is no easy way to change this right now.
It is also important to note, that a USB to UART serial adapter is not needed for any of these guides, as may be documented elsewhere across the int

Landrash

Setting up Pi Zero OTG - The quick way (No USB keyboard, mouse, HDMI monitor needed)

More details - http://blog.gbaman.info/?p=791

For this method, alongside your Pi Zero, MicroUSB cable and MicroSD card, only an additional computer is required, which can be running Windows (with Bonjour, iTunes or Quicktime installed), Mac OS or Linux (with Avahi Daemon installed, for example Ubuntu has it built in).
1. Flash Raspbian Jessie full or Raspbian Jessie Lite onto the SD card.
2. Once Raspbian is flashed, open up the boot partition (in Windows Explorer, Finder etc) and add to the bottom of the config.txt file dtoverlay=dwc2 on a new line, then save the file.
3. If using a recent release of Jessie (Dec 2016 onwards), then create a new file simply called ssh in the SD card as well. By default SSH i