slicer_vinylcut_config.ini

# generated by Slic3r 1.3.0 on 2022-01-30 13:05:52
adaptive_slicing = 0
adaptive_slicing_quality = 75%
avoid_crossing_perimeters = 0
bed_shape = 0x0,190x0,190x190,0x190
bed_temperature = 0
before_layer_gcode = 
between_objects_gcode = 
bottom_infill_pattern = rectilinear
bottom_solid_layers = 0
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_connections_width = 0
brim_width = 0
compatible_printers = 
complete_objects = 0
cooling = 0
default_acceleration = 0
disable_fan_first_layers = 3
dont_support_bridges = 1
duplicate_distance = 6
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
end_gcode = M104 S0 ; turn off temperature\nM140 S0; turn off bed (added)\nG28 X Y Z ; home X, Y and Z (M90 homes upward, so no issue)\nM84     ; disable motors\n
external_perimeter_extrusion_width = 0
external_perimeter_speed = 10
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1.37
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #C300FE
filament_cost = 0
filament_density = 0
filament_diameter = 2.85
filament_max_volumetric_speed = 0
filament_notes = ""
filament_settings_id = 
fill_angle = 45
fill_density = 0%
fill_gaps = 1
fill_pattern = grid
first_layer_acceleration = 0
first_layer_bed_temperature = 0
first_layer_extrusion_width = 0
first_layer_height = 0.1
first_layer_speed = 10
first_layer_temperature = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
has_heatbed = 0
host_type = octoprint
infill_acceleration = 0
infill_every_layers = 2
infill_extruder = 2
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 0
infill_speed = 80
interface_shells = 0
interior_brim_width = 0
layer_gcode = 
layer_height = 0.1
match_horizontal_surfaces = 0
max_fan_speed = 100
max_layer_height = 0.1
max_print_speed = 80
max_volumetric_speed = 0
min_fan_speed = 35
min_layer_height = 0
min_print_speed = 10
min_skirt_length = 5
notes = vinyl cutter settings
nozzle_diameter = 0.05
octoprint_apikey = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 10
perimeters = 1
post_process = 
pressure_advance = 0
print_host = 
print_settings_id = 
printer_notes = vinyl cut blade. \n\nOn General: set Z offset to -13 (or whatever is needed to press the plotter pen or blade into the foil)\nOn Extruder1:\nLift Z 10 mm on retract. Retract N mm on crossing minimal 0.1 mm between -999 and +999 (Because negative Z offset because cutter blade is shorter then hotend, default 0 wont work)
printer_settings_id = 
raft_layers = 0
regions_overlap = 0
resolution = 0
retract_before_travel = 0.01
retract_layer_change = 0
retract_length = 2
retract_length_toolchange = 10
retract_lift = 10
retract_lift_above = -999
retract_lift_below = 999
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
seam_position = aligned
sequential_print_priority = 0
serial_port = 
serial_speed = 250000
shortcuts = bottom_infill_pattern;fill_density;perimeters;brim_width;interior_brim_width;support_material
skirt_distance = 6
skirt_height = 1
skirts = 0
slowdown_below_layer_time = 5
small_perimeter_speed = 10
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
start_filament_gcode = "; Filament gcode\n"
start_gcode = G28 ; home all axes\n\nG21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\n
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 2
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_extrusion_width = 0
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_max_layers = 0
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 10
support_material_threshold = 60%
temperature = 0
thin_walls = 0
threads = 4
toolchange_gcode = 
top_infill_extrusion_width = 0
top_infill_pattern = concentric
top_solid_infill_speed = 15
top_solid_layers = 0
travel_speed = 130
use_firmware_retraction = 0
use_relative_e_distances = 0
use_set_and_wait_bed = 0
use_set_and_wait_extruder = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
xy_size_compensation = 0
z_offset = -11.5
z_steps_per_mm = 0