-
-
Save MaxBareiss/1bfb39dae05b8fe69336d817be4b7891 to your computer and use it in GitHub Desktop.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| # generated by PrusaSlicer 2.3.0+win64 on 2021-05-07 at 21:33:25 UTC | |
| [print:Fast 0.2] | |
| avoid_crossing_perimeters = 0 | |
| avoid_crossing_perimeters_max_detour = 0 | |
| bottom_fill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bottom_solid_min_thickness = 0 | |
| bridge_acceleration = 0 | |
| bridge_angle = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 0 | |
| clip_multipart_objects = 0 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| complete_objects = 0 | |
| default_acceleration = 500 | |
| dont_support_bridges = 1 | |
| draft_shield = 0 | |
| elefant_foot_compensation = 0 | |
| ensure_vertical_shell_thickness = 0 | |
| external_perimeter_extrusion_width = 0.45 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.45 | |
| fill_angle = 45 | |
| fill_density = 10% | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.42 | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 30 | |
| gcode_comments = 0 | |
| gcode_label_objects = 0 | |
| infill_acceleration = 0 | |
| infill_anchor = 600% | |
| infill_anchor_max = 50 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.45 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 25% | |
| infill_speed = 100 | |
| inherits = | |
| interface_shells = 0 | |
| ironing = 0 | |
| ironing_flowrate = 15% | |
| ironing_spacing = 0.1 | |
| ironing_speed = 15 | |
| ironing_type = top | |
| layer_height = 0.2 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.45 | |
| perimeter_speed = 90 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| single_extruder_multi_material_priming = 1 | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slice_closing_radius = 0.049 | |
| small_perimeter_speed = 33% | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.45 | |
| solid_infill_speed = 40 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_auto = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_contact_loops = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 2.5 | |
| support_material_speed = 100 | |
| support_material_synchronize_layers = 0 | |
| support_material_threshold = 0 | |
| support_material_with_sheath = 1 | |
| support_material_xy_spacing = 50% | |
| thin_walls = 1 | |
| threads = 12 | |
| top_fill_pattern = rectilinear | |
| top_infill_extrusion_width = 0.4 | |
| top_solid_infill_speed = 20 | |
| top_solid_layers = 3 | |
| top_solid_min_thickness = 0 | |
| travel_speed = 120 | |
| wipe_tower = 0 | |
| wipe_tower_bridging = 10 | |
| wipe_tower_no_sparse_layers = 0 | |
| wipe_tower_rotation_angle = 0 | |
| wipe_tower_width = 60 | |
| wipe_tower_x = 180 | |
| wipe_tower_y = 140 | |
| xy_size_compensation = -0.07 | |
| [print:Fast 0.3] | |
| avoid_crossing_perimeters = 0 | |
| avoid_crossing_perimeters_max_detour = 0 | |
| bottom_fill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bottom_solid_min_thickness = 0 | |
| bridge_acceleration = 0 | |
| bridge_angle = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 5 | |
| clip_multipart_objects = 0 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| complete_objects = 0 | |
| default_acceleration = 500 | |
| dont_support_bridges = 1 | |
| draft_shield = 0 | |
| elefant_foot_compensation = 0 | |
| ensure_vertical_shell_thickness = 0 | |
| external_perimeter_extrusion_width = 0.4 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.4 | |
| fill_angle = 45 | |
| fill_density = 30% | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.8 | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 30 | |
| gcode_comments = 0 | |
| gcode_label_objects = 0 | |
| infill_acceleration = 0 | |
| infill_anchor = 600% | |
| infill_anchor_max = 50 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.4 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 25% | |
| infill_speed = 100 | |
| inherits = | |
| interface_shells = 0 | |
| ironing = 0 | |
| ironing_flowrate = 15% | |
| ironing_spacing = 0.1 | |
| ironing_speed = 15 | |
| ironing_type = top | |
| layer_height = 0.3 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.4 | |
| perimeter_speed = 90 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| single_extruder_multi_material_priming = 1 | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slice_closing_radius = 0.049 | |
| small_perimeter_speed = 33% | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.4 | |
| solid_infill_speed = 40 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_auto = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_contact_loops = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 2.5 | |
| support_material_speed = 100 | |
| support_material_synchronize_layers = 0 | |
| support_material_threshold = 0 | |
| support_material_with_sheath = 1 | |
| support_material_xy_spacing = 50% | |
| thin_walls = 1 | |
| threads = 12 | |
| top_fill_pattern = rectilinear | |
| top_infill_extrusion_width = 0.4 | |
| top_solid_infill_speed = 20 | |
| top_solid_layers = 3 | |
| top_solid_min_thickness = 0 | |
| travel_speed = 120 | |
| wipe_tower = 0 | |
| wipe_tower_bridging = 10 | |
| wipe_tower_no_sparse_layers = 0 | |
| wipe_tower_rotation_angle = 0 | |
| wipe_tower_width = 60 | |
| wipe_tower_x = 180 | |
| wipe_tower_y = 140 | |
| xy_size_compensation = -0.07 | |
| [print:Fast 0.3 NIH] | |
| avoid_crossing_perimeters = 0 | |
| avoid_crossing_perimeters_max_detour = 0 | |
| bottom_fill_pattern = rectilinear | |
| bottom_solid_layers = 2 | |
| bottom_solid_min_thickness = 0 | |
| bridge_acceleration = 0 | |
| bridge_angle = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 5 | |
| clip_multipart_objects = 0 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| complete_objects = 0 | |
| default_acceleration = 500 | |
| dont_support_bridges = 1 | |
| draft_shield = 0 | |
| elefant_foot_compensation = 0 | |
| ensure_vertical_shell_thickness = 0 | |
| external_perimeter_extrusion_width = 0.8 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.8 | |
| fill_angle = 45 | |
| fill_density = 30% | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.8 | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 30 | |
| gcode_comments = 0 | |
| gcode_label_objects = 0 | |
| infill_acceleration = 0 | |
| infill_anchor = 600% | |
| infill_anchor_max = 50 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.8 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 25% | |
| infill_speed = 100 | |
| inherits = | |
| interface_shells = 0 | |
| ironing = 0 | |
| ironing_flowrate = 15% | |
| ironing_spacing = 0.1 | |
| ironing_speed = 15 | |
| ironing_type = top | |
| layer_height = 0.3 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.8 | |
| perimeter_speed = 90 | |
| perimeters = 2 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| single_extruder_multi_material_priming = 1 | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slice_closing_radius = 0.049 | |
| small_perimeter_speed = 33% | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.8 | |
| solid_infill_speed = 40 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_auto = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_contact_loops = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 2.5 | |
| support_material_speed = 100 | |
| support_material_synchronize_layers = 0 | |
| support_material_threshold = 0 | |
| support_material_with_sheath = 1 | |
| support_material_xy_spacing = 50% | |
| thin_walls = 1 | |
| threads = 12 | |
| top_fill_pattern = rectilinear | |
| top_infill_extrusion_width = 0.8 | |
| top_solid_infill_speed = 20 | |
| top_solid_layers = 2 | |
| top_solid_min_thickness = 0 | |
| travel_speed = 120 | |
| wipe_tower = 0 | |
| wipe_tower_bridging = 10 | |
| wipe_tower_no_sparse_layers = 0 | |
| wipe_tower_rotation_angle = 0 | |
| wipe_tower_width = 60 | |
| wipe_tower_x = 180 | |
| wipe_tower_y = 140 | |
| xy_size_compensation = -0.07 | |
| [print:Fast 0.3 Strong] | |
| avoid_crossing_perimeters = 0 | |
| avoid_crossing_perimeters_max_detour = 0 | |
| bottom_fill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bottom_solid_min_thickness = 0 | |
| bridge_acceleration = 0 | |
| bridge_angle = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 0 | |
| clip_multipart_objects = 0 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| complete_objects = 0 | |
| default_acceleration = 500 | |
| dont_support_bridges = 1 | |
| draft_shield = 0 | |
| elefant_foot_compensation = 0 | |
| ensure_vertical_shell_thickness = 0 | |
| external_perimeter_extrusion_width = 0.8 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.8 | |
| fill_angle = 45 | |
| fill_density = 10% | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.8 | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 30 | |
| gcode_comments = 0 | |
| gcode_label_objects = 0 | |
| infill_acceleration = 0 | |
| infill_anchor = 600% | |
| infill_anchor_max = 50 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.8 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 100 | |
| inherits = | |
| interface_shells = 0 | |
| ironing = 0 | |
| ironing_flowrate = 15% | |
| ironing_spacing = 0.1 | |
| ironing_speed = 15 | |
| ironing_type = top | |
| layer_height = 0.3 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.8 | |
| perimeter_speed = 90 | |
| perimeters = 2 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| single_extruder_multi_material_priming = 1 | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slice_closing_radius = 0.049 | |
| small_perimeter_speed = 33% | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.8 | |
| solid_infill_speed = 40 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_auto = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_contact_loops = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 2.5 | |
| support_material_speed = 100 | |
| support_material_synchronize_layers = 0 | |
| support_material_threshold = 0 | |
| support_material_with_sheath = 1 | |
| support_material_xy_spacing = 50% | |
| thin_walls = 1 | |
| threads = 12 | |
| top_fill_pattern = rectilinear | |
| top_infill_extrusion_width = 0.8 | |
| top_solid_infill_speed = 20 | |
| top_solid_layers = 3 | |
| top_solid_min_thickness = 0 | |
| travel_speed = 120 | |
| wipe_tower = 0 | |
| wipe_tower_bridging = 10 | |
| wipe_tower_no_sparse_layers = 0 | |
| wipe_tower_rotation_angle = 0 | |
| wipe_tower_width = 60 | |
| wipe_tower_x = 180 | |
| wipe_tower_y = 140 | |
| xy_size_compensation = -0.07 | |
| [print:Fast 0.3 Thick] | |
| avoid_crossing_perimeters = 0 | |
| avoid_crossing_perimeters_max_detour = 0 | |
| bottom_fill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bottom_solid_min_thickness = 0 | |
| bridge_acceleration = 0 | |
| bridge_angle = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 5 | |
| clip_multipart_objects = 0 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| complete_objects = 0 | |
| default_acceleration = 500 | |
| dont_support_bridges = 1 | |
| draft_shield = 0 | |
| elefant_foot_compensation = 0 | |
| ensure_vertical_shell_thickness = 0 | |
| external_perimeter_extrusion_width = 0.8 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.8 | |
| fill_angle = 45 | |
| fill_density = 100% | |
| fill_pattern = rectilinear | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.8 | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 30 | |
| gcode_comments = 0 | |
| gcode_label_objects = 0 | |
| infill_acceleration = 0 | |
| infill_anchor = 600% | |
| infill_anchor_max = 50 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.8 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 25% | |
| infill_speed = 80 | |
| inherits = | |
| interface_shells = 0 | |
| ironing = 0 | |
| ironing_flowrate = 15% | |
| ironing_spacing = 0.1 | |
| ironing_speed = 15 | |
| ironing_type = top | |
| layer_height = 0.3 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.8 | |
| perimeter_speed = 90 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| single_extruder_multi_material_priming = 1 | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slice_closing_radius = 0.049 | |
| small_perimeter_speed = 33% | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.8 | |
| solid_infill_speed = 40 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_auto = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_contact_loops = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 2.5 | |
| support_material_speed = 100 | |
| support_material_synchronize_layers = 0 | |
| support_material_threshold = 0 | |
| support_material_with_sheath = 1 | |
| support_material_xy_spacing = 50% | |
| thin_walls = 1 | |
| threads = 12 | |
| top_fill_pattern = rectilinear | |
| top_infill_extrusion_width = 0.8 | |
| top_solid_infill_speed = 20 | |
| top_solid_layers = 3 | |
| top_solid_min_thickness = 0 | |
| travel_speed = 120 | |
| wipe_tower = 0 | |
| wipe_tower_bridging = 10 | |
| wipe_tower_no_sparse_layers = 0 | |
| wipe_tower_rotation_angle = 0 | |
| wipe_tower_width = 60 | |
| wipe_tower_x = 180 | |
| wipe_tower_y = 140 | |
| xy_size_compensation = -0.07 | |
| [print:Makerbot] | |
| avoid_crossing_perimeters = 0 | |
| avoid_crossing_perimeters_max_detour = 0 | |
| bottom_fill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bottom_solid_min_thickness = 0 | |
| bridge_acceleration = 0 | |
| bridge_angle = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 0 | |
| clip_multipart_objects = 0 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| draft_shield = 0 | |
| elefant_foot_compensation = 0 | |
| ensure_vertical_shell_thickness = 0 | |
| external_perimeter_extrusion_width = 0.45 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0.45 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_pattern = stars | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.42 | |
| first_layer_height = 0.35 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| gcode_label_objects = 0 | |
| infill_acceleration = 0 | |
| infill_anchor = 600% | |
| infill_anchor_max = 50 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.45 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 25% | |
| infill_speed = 80 | |
| inherits = | |
| interface_shells = 0 | |
| ironing = 0 | |
| ironing_flowrate = 15% | |
| ironing_spacing = 0.1 | |
| ironing_speed = 15 | |
| ironing_type = top | |
| layer_height = 0.3 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.45 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| single_extruder_multi_material_priming = 1 | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slice_closing_radius = 0.049 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.45 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_auto = 1 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_contact_loops = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_synchronize_layers = 0 | |
| support_material_threshold = 0 | |
| support_material_with_sheath = 1 | |
| support_material_xy_spacing = 50% | |
| thin_walls = 1 | |
| threads = 12 | |
| top_fill_pattern = rectilinear | |
| top_infill_extrusion_width = 0.4 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| top_solid_min_thickness = 0 | |
| travel_speed = 130 | |
| wipe_tower = 0 | |
| wipe_tower_bridging = 10 | |
| wipe_tower_no_sparse_layers = 0 | |
| wipe_tower_rotation_angle = 0 | |
| wipe_tower_width = 60 | |
| wipe_tower_x = 180 | |
| wipe_tower_y = 140 | |
| xy_size_compensation = 0 | |
| [print:Normal 0.2] | |
| avoid_crossing_perimeters = 0 | |
| avoid_crossing_perimeters_max_detour = 0 | |
| bottom_fill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bottom_solid_min_thickness = 0 | |
| bridge_acceleration = 0 | |
| bridge_angle = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 5 | |
| clip_multipart_objects = 0 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| complete_objects = 0 | |
| default_acceleration = 500 | |
| dont_support_bridges = 1 | |
| draft_shield = 0 | |
| elefant_foot_compensation = 0 | |
| ensure_vertical_shell_thickness = 0 | |
| external_perimeter_extrusion_width = 0.3 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 4 | |
| extruder_clearance_radius = 40 | |
| extrusion_width = 0.45 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_pattern = gyroid | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.8 | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| gcode_label_objects = 0 | |
| infill_acceleration = 0 | |
| infill_anchor = 600% | |
| infill_anchor_max = 50 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.45 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 25% | |
| infill_speed = 80 | |
| inherits = | |
| interface_shells = 0 | |
| ironing = 0 | |
| ironing_flowrate = 15% | |
| ironing_spacing = 0.1 | |
| ironing_speed = 15 | |
| ironing_type = top | |
| layer_height = 0.2 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.45 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| resolution = 0.05 | |
| seam_position = aligned | |
| single_extruder_multi_material_priming = 1 | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slice_closing_radius = 0.049 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.45 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_auto = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_contact_loops = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_synchronize_layers = 0 | |
| support_material_threshold = 0 | |
| support_material_with_sheath = 1 | |
| support_material_xy_spacing = 50% | |
| thin_walls = 1 | |
| threads = 12 | |
| top_fill_pattern = rectilinear | |
| top_infill_extrusion_width = 0.4 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| top_solid_min_thickness = 0 | |
| travel_speed = 100 | |
| wipe_tower = 0 | |
| wipe_tower_bridging = 10 | |
| wipe_tower_no_sparse_layers = 0 | |
| wipe_tower_rotation_angle = 0 | |
| wipe_tower_width = 60 | |
| wipe_tower_x = 180 | |
| wipe_tower_y = 140 | |
| xy_size_compensation = -0.07 | |
| [print:Normal 0.2 CNCKitchen Strong] | |
| avoid_crossing_perimeters = 0 | |
| avoid_crossing_perimeters_max_detour = 0 | |
| bottom_fill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bottom_solid_min_thickness = 0 | |
| bridge_acceleration = 0 | |
| bridge_angle = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 0 | |
| clip_multipart_objects = 0 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| complete_objects = 0 | |
| default_acceleration = 500 | |
| dont_support_bridges = 1 | |
| draft_shield = 0 | |
| elefant_foot_compensation = 0 | |
| ensure_vertical_shell_thickness = 0 | |
| external_perimeter_extrusion_width = 0.8 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 4 | |
| extruder_clearance_radius = 40 | |
| extrusion_width = 0.8 | |
| fill_angle = 45 | |
| fill_density = 50% | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.8 | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| gcode_label_objects = 0 | |
| infill_acceleration = 0 | |
| infill_anchor = 600% | |
| infill_anchor_max = 50 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.8 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| inherits = | |
| interface_shells = 0 | |
| ironing = 0 | |
| ironing_flowrate = 15% | |
| ironing_spacing = 0.1 | |
| ironing_speed = 15 | |
| ironing_type = top | |
| layer_height = 0.2 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.8 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| single_extruder_multi_material_priming = 1 | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slice_closing_radius = 0.049 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.8 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_auto = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_contact_loops = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_synchronize_layers = 0 | |
| support_material_threshold = 0 | |
| support_material_with_sheath = 1 | |
| support_material_xy_spacing = 50% | |
| thin_walls = 1 | |
| threads = 12 | |
| top_fill_pattern = rectilinear | |
| top_infill_extrusion_width = 0.8 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| top_solid_min_thickness = 0 | |
| travel_speed = 100 | |
| wipe_tower = 0 | |
| wipe_tower_bridging = 10 | |
| wipe_tower_no_sparse_layers = 0 | |
| wipe_tower_rotation_angle = 0 | |
| wipe_tower_width = 60 | |
| wipe_tower_x = 180 | |
| wipe_tower_y = 140 | |
| xy_size_compensation = -0.07 | |
| [print:Normal 0.2 Strong] | |
| avoid_crossing_perimeters = 0 | |
| avoid_crossing_perimeters_max_detour = 0 | |
| bottom_fill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bottom_solid_min_thickness = 0 | |
| bridge_acceleration = 0 | |
| bridge_angle = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 0 | |
| clip_multipart_objects = 0 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| complete_objects = 0 | |
| default_acceleration = 500 | |
| dont_support_bridges = 1 | |
| draft_shield = 0 | |
| elefant_foot_compensation = 0 | |
| ensure_vertical_shell_thickness = 0 | |
| external_perimeter_extrusion_width = 0.45 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 4 | |
| extruder_clearance_radius = 40 | |
| extrusion_width = 0.45 | |
| fill_angle = 45 | |
| fill_density = 50% | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.42 | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| gcode_label_objects = 0 | |
| infill_acceleration = 0 | |
| infill_anchor = 600% | |
| infill_anchor_max = 50 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.45 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 25% | |
| infill_speed = 80 | |
| inherits = | |
| interface_shells = 0 | |
| ironing = 0 | |
| ironing_flowrate = 15% | |
| ironing_spacing = 0.1 | |
| ironing_speed = 15 | |
| ironing_type = top | |
| layer_height = 0.2 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.45 | |
| perimeter_speed = 60 | |
| perimeters = 6 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| single_extruder_multi_material_priming = 1 | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slice_closing_radius = 0.049 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.45 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_auto = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_contact_loops = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_synchronize_layers = 0 | |
| support_material_threshold = 0 | |
| support_material_with_sheath = 1 | |
| support_material_xy_spacing = 50% | |
| thin_walls = 1 | |
| threads = 12 | |
| top_fill_pattern = rectilinear | |
| top_infill_extrusion_width = 0.4 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| top_solid_min_thickness = 0 | |
| travel_speed = 100 | |
| wipe_tower = 0 | |
| wipe_tower_bridging = 10 | |
| wipe_tower_no_sparse_layers = 0 | |
| wipe_tower_rotation_angle = 0 | |
| wipe_tower_width = 60 | |
| wipe_tower_x = 180 | |
| wipe_tower_y = 140 | |
| xy_size_compensation = -0.07 | |
| [print:Tile 0.3 outside 0.2 layer] | |
| avoid_crossing_perimeters = 0 | |
| avoid_crossing_perimeters_max_detour = 0 | |
| bottom_fill_pattern = rectilinear | |
| bottom_solid_layers = 2 | |
| bottom_solid_min_thickness = 0 | |
| bridge_acceleration = 0 | |
| bridge_angle = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 5 | |
| clip_multipart_objects = 0 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| complete_objects = 0 | |
| default_acceleration = 500 | |
| dont_support_bridges = 1 | |
| draft_shield = 0 | |
| elefant_foot_compensation = 0 | |
| ensure_vertical_shell_thickness = 0 | |
| external_perimeter_extrusion_width = 0.3 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 4 | |
| extruder_clearance_radius = 40 | |
| extrusion_width = 0.45 | |
| fill_angle = 45 | |
| fill_density = 5% | |
| fill_pattern = line | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 0.8 | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| gcode_label_objects = 0 | |
| infill_acceleration = 0 | |
| infill_anchor = 600% | |
| infill_anchor_max = 50 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0.45 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 25% | |
| infill_speed = 80 | |
| inherits = | |
| interface_shells = 0 | |
| ironing = 0 | |
| ironing_flowrate = 15% | |
| ironing_spacing = 0.1 | |
| ironing_speed = 15 | |
| ironing_type = top | |
| layer_height = 0.2 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0.45 | |
| perimeter_speed = 60 | |
| perimeters = 1 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| resolution = 0.05 | |
| seam_position = aligned | |
| single_extruder_multi_material_priming = 1 | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slice_closing_radius = 0.049 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0.45 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_auto = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0.35 | |
| support_material_interface_contact_loops = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = rectilinear | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_synchronize_layers = 0 | |
| support_material_threshold = 0 | |
| support_material_with_sheath = 1 | |
| support_material_xy_spacing = 50% | |
| thin_walls = 1 | |
| threads = 12 | |
| top_fill_pattern = rectilinear | |
| top_infill_extrusion_width = 0.4 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 2 | |
| top_solid_min_thickness = 0 | |
| travel_speed = 100 | |
| wipe_tower = 0 | |
| wipe_tower_bridging = 10 | |
| wipe_tower_no_sparse_layers = 0 | |
| wipe_tower_rotation_angle = 0 | |
| wipe_tower_width = 60 | |
| wipe_tower_x = 180 | |
| wipe_tower_y = 140 | |
| xy_size_compensation = -0.07 | |
| [filament:Makerbot] | |
| bed_temperature = 0 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #29B2B2 | |
| filament_cooling_final_speed = 3.4 | |
| filament_cooling_initial_speed = 2.2 | |
| filament_cooling_moves = 4 | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_deretract_speed = nil | |
| filament_diameter = 1.75 | |
| filament_load_time = 0 | |
| filament_loading_speed = 28 | |
| filament_loading_speed_start = 3 | |
| filament_max_volumetric_speed = 0 | |
| filament_minimal_purge_on_wipe_tower = 15 | |
| filament_notes = "" | |
| filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" | |
| filament_retract_before_travel = nil | |
| filament_retract_before_wipe = nil | |
| filament_retract_layer_change = nil | |
| filament_retract_length = nil | |
| filament_retract_lift = nil | |
| filament_retract_lift_above = nil | |
| filament_retract_lift_below = nil | |
| filament_retract_restart_extra = nil | |
| filament_retract_speed = nil | |
| filament_settings_id = "" | |
| filament_soluble = 0 | |
| filament_spool_weight = 0 | |
| filament_toolchange_delay = 0 | |
| filament_type = PLA | |
| filament_unload_time = 0 | |
| filament_unloading_speed = 90 | |
| filament_unloading_speed_start = 100 | |
| filament_vendor = (Unknown) | |
| filament_wipe = nil | |
| first_layer_bed_temperature = 0 | |
| first_layer_temperature = 210 | |
| full_fan_speed_layer = 0 | |
| inherits = | |
| max_fan_speed = 100 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 210 | |
| [filament:PLA Cool] | |
| bed_temperature = 50 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = | |
| cooling = 1 | |
| disable_fan_first_layers = 2 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #29B2B2 | |
| filament_cooling_final_speed = 3.4 | |
| filament_cooling_initial_speed = 2.2 | |
| filament_cooling_moves = 4 | |
| filament_cost = 20 | |
| filament_density = 1 | |
| filament_deretract_speed = nil | |
| filament_diameter = 1.75 | |
| filament_load_time = 0 | |
| filament_loading_speed = 28 | |
| filament_loading_speed_start = 3 | |
| filament_max_volumetric_speed = 0 | |
| filament_minimal_purge_on_wipe_tower = 15 | |
| filament_notes = "" | |
| filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" | |
| filament_retract_before_travel = nil | |
| filament_retract_before_wipe = nil | |
| filament_retract_layer_change = nil | |
| filament_retract_length = nil | |
| filament_retract_lift = nil | |
| filament_retract_lift_above = nil | |
| filament_retract_lift_below = nil | |
| filament_retract_restart_extra = nil | |
| filament_retract_speed = nil | |
| filament_settings_id = "" | |
| filament_soluble = 0 | |
| filament_spool_weight = 0 | |
| filament_toolchange_delay = 0 | |
| filament_type = PLA | |
| filament_unload_time = 0 | |
| filament_unloading_speed = 90 | |
| filament_unloading_speed_start = 100 | |
| filament_vendor = (Unknown) | |
| filament_wipe = nil | |
| first_layer_bed_temperature = 50 | |
| first_layer_temperature = 210 | |
| full_fan_speed_layer = 0 | |
| inherits = | |
| max_fan_speed = 100 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 10 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 210 | |
| [filament:PLA No Cool] | |
| bed_temperature = 50 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = | |
| cooling = 0 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #29B2B2 | |
| filament_cooling_final_speed = 3.4 | |
| filament_cooling_initial_speed = 2.2 | |
| filament_cooling_moves = 4 | |
| filament_cost = 0 | |
| filament_density = 1.25 | |
| filament_deretract_speed = nil | |
| filament_diameter = 1.75 | |
| filament_load_time = 0 | |
| filament_loading_speed = 28 | |
| filament_loading_speed_start = 3 | |
| filament_max_volumetric_speed = 0 | |
| filament_minimal_purge_on_wipe_tower = 15 | |
| filament_notes = "" | |
| filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" | |
| filament_retract_before_travel = nil | |
| filament_retract_before_wipe = nil | |
| filament_retract_layer_change = nil | |
| filament_retract_length = nil | |
| filament_retract_lift = nil | |
| filament_retract_lift_above = nil | |
| filament_retract_lift_below = nil | |
| filament_retract_restart_extra = nil | |
| filament_retract_speed = nil | |
| filament_settings_id = "" | |
| filament_soluble = 0 | |
| filament_spool_weight = 0 | |
| filament_toolchange_delay = 0 | |
| filament_type = PLA | |
| filament_unload_time = 0 | |
| filament_unloading_speed = 90 | |
| filament_unloading_speed_start = 100 | |
| filament_vendor = (Unknown) | |
| filament_wipe = nil | |
| first_layer_bed_temperature = 50 | |
| first_layer_temperature = 210 | |
| full_fan_speed_layer = 0 | |
| inherits = | |
| max_fan_speed = 100 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 210 | |
| [filament:PLA No Cool Hot] | |
| bed_temperature = 50 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = | |
| cooling = 0 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #29B2B2 | |
| filament_cooling_final_speed = 3.4 | |
| filament_cooling_initial_speed = 2.2 | |
| filament_cooling_moves = 4 | |
| filament_cost = 0 | |
| filament_density = 1.25 | |
| filament_deretract_speed = nil | |
| filament_diameter = 1.75 | |
| filament_load_time = 0 | |
| filament_loading_speed = 28 | |
| filament_loading_speed_start = 3 | |
| filament_max_volumetric_speed = 0 | |
| filament_minimal_purge_on_wipe_tower = 15 | |
| filament_notes = "" | |
| filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" | |
| filament_retract_before_travel = nil | |
| filament_retract_before_wipe = nil | |
| filament_retract_layer_change = nil | |
| filament_retract_length = nil | |
| filament_retract_lift = nil | |
| filament_retract_lift_above = nil | |
| filament_retract_lift_below = nil | |
| filament_retract_restart_extra = nil | |
| filament_retract_speed = nil | |
| filament_settings_id = "" | |
| filament_soluble = 0 | |
| filament_spool_weight = 0 | |
| filament_toolchange_delay = 0 | |
| filament_type = PLA | |
| filament_unload_time = 0 | |
| filament_unloading_speed = 90 | |
| filament_unloading_speed_start = 100 | |
| filament_vendor = (Unknown) | |
| filament_wipe = nil | |
| first_layer_bed_temperature = 50 | |
| first_layer_temperature = 215 | |
| full_fan_speed_layer = 0 | |
| inherits = | |
| max_fan_speed = 100 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 215 | |
| [sla_print:0.025 Normal] | |
| compatible_printers = | |
| compatible_printers_condition = | |
| default_sla_print_profile = | |
| faded_layers = 10 | |
| hollowing_closing_distance = 2 | |
| hollowing_enable = 0 | |
| hollowing_min_thickness = 3 | |
| hollowing_quality = 0.5 | |
| inherits = | |
| layer_height = 0.025 | |
| output_filename_format = [input_filename_base].sl1 | |
| pad_around_object = 0 | |
| pad_around_object_everywhere = 0 | |
| pad_brim_size = 1.6 | |
| pad_enable = 1 | |
| pad_max_merge_distance = 50 | |
| pad_object_connector_penetration = 0.3 | |
| pad_object_connector_stride = 10 | |
| pad_object_connector_width = 0.5 | |
| pad_object_gap = 1 | |
| pad_wall_height = 0 | |
| pad_wall_slope = 90 | |
| pad_wall_thickness = 1 | |
| sla_print_settings_id = | |
| slice_closing_radius = 0.005 | |
| support_base_diameter = 3 | |
| support_base_height = 1 | |
| support_base_safety_distance = 1 | |
| support_buildplate_only = 0 | |
| support_critical_angle = 45 | |
| support_head_front_diameter = 0.4 | |
| support_head_penetration = 0.2 | |
| support_head_width = 3 | |
| support_max_bridge_length = 10 | |
| support_max_bridges_on_pillar = 3 | |
| support_max_pillar_link_distance = 10 | |
| support_object_elevation = 5 | |
| support_pillar_connection_mode = zigzag | |
| support_pillar_diameter = 1.2 | |
| support_pillar_widening_factor = 0 | |
| support_points_density_relative = 150 | |
| support_points_minimal_distance = 1 | |
| support_small_pillar_diameter_percent = 50% | |
| supports_enable = 1 | |
| [sla_print:0.05 Normal Hacksburg] | |
| compatible_printers = | |
| compatible_printers_condition = | |
| default_sla_print_profile = | |
| faded_layers = 10 | |
| hollowing_closing_distance = 2 | |
| hollowing_enable = 0 | |
| hollowing_min_thickness = 3 | |
| hollowing_quality = 0.5 | |
| inherits = | |
| layer_height = 0.05 | |
| output_filename_format = [input_filename_base].sl1 | |
| pad_around_object = 0 | |
| pad_around_object_everywhere = 0 | |
| pad_brim_size = 1.6 | |
| pad_enable = 1 | |
| pad_max_merge_distance = 50 | |
| pad_object_connector_penetration = 0.3 | |
| pad_object_connector_stride = 10 | |
| pad_object_connector_width = 0.5 | |
| pad_object_gap = 1 | |
| pad_wall_height = 0 | |
| pad_wall_slope = 90 | |
| pad_wall_thickness = 1 | |
| sla_print_settings_id = | |
| slice_closing_radius = 0.005 | |
| support_base_diameter = 3 | |
| support_base_height = 1 | |
| support_base_safety_distance = 1 | |
| support_buildplate_only = 0 | |
| support_critical_angle = 45 | |
| support_head_front_diameter = 0.8 | |
| support_head_penetration = 0.4 | |
| support_head_width = 3 | |
| support_max_bridge_length = 10 | |
| support_max_bridges_on_pillar = 3 | |
| support_max_pillar_link_distance = 10 | |
| support_object_elevation = 5 | |
| support_pillar_connection_mode = zigzag | |
| support_pillar_diameter = 1.2 | |
| support_pillar_widening_factor = 0 | |
| support_points_density_relative = 150 | |
| support_points_minimal_distance = 1 | |
| support_small_pillar_diameter_percent = 50% | |
| supports_enable = 1 | |
| [sla_print:0.05 Normal Small] | |
| compatible_printers = | |
| compatible_printers_condition = | |
| default_sla_print_profile = | |
| faded_layers = 10 | |
| hollowing_closing_distance = 2 | |
| hollowing_enable = 0 | |
| hollowing_min_thickness = 3 | |
| hollowing_quality = 0.5 | |
| inherits = | |
| layer_height = 0.05 | |
| output_filename_format = [input_filename_base].sl1 | |
| pad_around_object = 0 | |
| pad_around_object_everywhere = 0 | |
| pad_brim_size = 1.6 | |
| pad_enable = 1 | |
| pad_max_merge_distance = 50 | |
| pad_object_connector_penetration = 0.3 | |
| pad_object_connector_stride = 10 | |
| pad_object_connector_width = 0.5 | |
| pad_object_gap = 1 | |
| pad_wall_height = 0 | |
| pad_wall_slope = 90 | |
| pad_wall_thickness = 1 | |
| sla_print_settings_id = | |
| slice_closing_radius = 0.005 | |
| support_base_diameter = 3 | |
| support_base_height = 1 | |
| support_base_safety_distance = 1 | |
| support_buildplate_only = 0 | |
| support_critical_angle = 45 | |
| support_head_front_diameter = 0.8 | |
| support_head_penetration = 0.4 | |
| support_head_width = 3 | |
| support_max_bridge_length = 10 | |
| support_max_bridges_on_pillar = 3 | |
| support_max_pillar_link_distance = 10 | |
| support_object_elevation = 5 | |
| support_pillar_connection_mode = zigzag | |
| support_pillar_diameter = 1.2 | |
| support_pillar_widening_factor = 0 | |
| support_points_density_relative = 150 | |
| support_points_minimal_distance = 1 | |
| support_small_pillar_diameter_percent = 50% | |
| supports_enable = 1 | |
| [sla_print:0.1 Normal] | |
| compatible_printers = | |
| compatible_printers_condition = | |
| default_sla_print_profile = | |
| faded_layers = 10 | |
| hollowing_closing_distance = 2 | |
| hollowing_enable = 0 | |
| hollowing_min_thickness = 3 | |
| hollowing_quality = 0.5 | |
| inherits = | |
| layer_height = 0.1 | |
| output_filename_format = [input_filename_base].sl1 | |
| pad_around_object = 0 | |
| pad_around_object_everywhere = 0 | |
| pad_brim_size = 1.6 | |
| pad_enable = 1 | |
| pad_max_merge_distance = 50 | |
| pad_object_connector_penetration = 0.3 | |
| pad_object_connector_stride = 10 | |
| pad_object_connector_width = 0.5 | |
| pad_object_gap = 1 | |
| pad_wall_height = 0 | |
| pad_wall_slope = 90 | |
| pad_wall_thickness = 1 | |
| sla_print_settings_id = | |
| slice_closing_radius = 0.005 | |
| support_base_diameter = 3 | |
| support_base_height = 1 | |
| support_base_safety_distance = 1 | |
| support_buildplate_only = 0 | |
| support_critical_angle = 45 | |
| support_head_front_diameter = 0.8 | |
| support_head_penetration = 0.4 | |
| support_head_width = 3 | |
| support_max_bridge_length = 10 | |
| support_max_bridges_on_pillar = 3 | |
| support_max_pillar_link_distance = 10 | |
| support_object_elevation = 5 | |
| support_pillar_connection_mode = zigzag | |
| support_pillar_diameter = 1.2 | |
| support_pillar_widening_factor = 0 | |
| support_points_density_relative = 150 | |
| support_points_minimal_distance = 1 | |
| support_small_pillar_diameter_percent = 50% | |
| supports_enable = 1 | |
| [sla_material:Elegoo Gray] | |
| bottle_cost = 0 | |
| bottle_volume = 1000 | |
| bottle_weight = 1 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = | |
| default_sla_material_profile = | |
| exposure_time = 8 | |
| inherits = | |
| initial_exposure_time = 80 | |
| initial_layer_height = 0.05 | |
| material_correction = 1,1,1 | |
| material_density = 1 | |
| material_notes = | |
| material_type = Tough | |
| material_vendor = Made for Prusa | |
| sla_material_settings_id = | |
| [sla_material:Normal 0.025] | |
| bottle_cost = 40 | |
| bottle_volume = 1000 | |
| bottle_weight = 1 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = | |
| default_sla_material_profile = | |
| exposure_time = 8 | |
| inherits = | |
| initial_exposure_time = 80 | |
| initial_layer_height = 0.025 | |
| material_correction = 1,1 | |
| material_density = 1 | |
| material_notes = | |
| material_type = Tough | |
| material_vendor = (Unknown) | |
| sla_material_settings_id = | |
| [sla_material:iFUN HiTemp Gray] | |
| bottle_cost = 27.99 | |
| bottle_volume = 500 | |
| bottle_weight = 0.5 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = layer_height == 0.05 | |
| default_sla_material_profile = | |
| exposure_time = 16 | |
| inherits = | |
| initial_exposure_time = 160 | |
| initial_layer_height = 0.05 | |
| material_correction = 0.99403,1,1 | |
| material_density = 1 | |
| material_notes = | |
| material_type = Tough | |
| material_vendor = Made for Prusa | |
| sla_material_settings_id = | |
| [sla_material:iFUN HiTemp Gray 0.1] | |
| bottle_cost = 27.99 | |
| bottle_volume = 500 | |
| bottle_weight = 0.5 | |
| compatible_printers = | |
| compatible_printers_condition = | |
| compatible_prints = | |
| compatible_prints_condition = | |
| default_sla_material_profile = | |
| exposure_time = 16 | |
| inherits = | |
| initial_exposure_time = 160 | |
| initial_layer_height = 0.05 | |
| material_correction = 0.99403,1,1 | |
| material_density = 1 | |
| material_notes = | |
| material_type = Tough | |
| material_vendor = Made for Prusa | |
| sla_material_settings_id = | |
| [printer:Anycubic Photon] | |
| absolute_correction = -0.0575 | |
| area_fill = 50 | |
| bed_custom_model = | |
| bed_custom_texture = | |
| bed_shape = 1.48x1.02,119.48x1.02,119.48x67.02,1.48x67.02 | |
| default_sla_material_profile = Prusa Orange Tough 0.05 | |
| default_sla_print_profile = 0.05 Normal | |
| display_height = 68.04 | |
| display_mirror_x = 1 | |
| display_mirror_y = 0 | |
| display_orientation = portrait | |
| display_pixels_x = 2560 | |
| display_pixels_y = 1440 | |
| display_width = 120.96 | |
| elefant_foot_compensation = 0.2 | |
| elefant_foot_min_width = 0.2 | |
| fast_tilt_time = 5 | |
| gamma_correction = 0 | |
| host_type = octoprint | |
| inherits = | |
| max_exposure_time = 120 | |
| max_initial_exposure_time = 300 | |
| max_print_height = 150 | |
| min_exposure_time = 1 | |
| min_initial_exposure_time = 1 | |
| print_host = | |
| printer_model = SL1 | |
| printer_notes = | |
| printer_settings_id = | |
| printer_technology = SLA | |
| printer_variant = default | |
| printer_vendor = | |
| printhost_apikey = | |
| printhost_cafile = | |
| relative_correction = 0.99544,1 | |
| slow_tilt_time = 8 | |
| thumbnails = 400x400,800x480 | |
| [printer:Anycubic Photon Gray] | |
| absolute_correction = -0.0575 | |
| area_fill = 50 | |
| bed_custom_model = | |
| bed_custom_texture = | |
| bed_shape = 1.48x1.02,119.48x1.02,119.48x67.02,1.48x67.02 | |
| default_sla_material_profile = Prusa Orange Tough 0.05 | |
| default_sla_print_profile = 0.05 Normal | |
| display_height = 68.04 | |
| display_mirror_x = 1 | |
| display_mirror_y = 0 | |
| display_orientation = portrait | |
| display_pixels_x = 2560 | |
| display_pixels_y = 1440 | |
| display_width = 120.96 | |
| elefant_foot_compensation = 0.2 | |
| elefant_foot_min_width = 0.2 | |
| fast_tilt_time = 5 | |
| gamma_correction = 0 | |
| host_type = octoprint | |
| inherits = | |
| max_exposure_time = 120 | |
| max_initial_exposure_time = 300 | |
| max_print_height = 150 | |
| min_exposure_time = 1 | |
| min_initial_exposure_time = 1 | |
| print_host = | |
| printer_model = SL1 | |
| printer_notes = | |
| printer_settings_id = | |
| printer_technology = SLA | |
| printer_variant = default | |
| printer_vendor = | |
| printhost_apikey = | |
| printhost_cafile = | |
| relative_correction = 0.99544,1 | |
| slow_tilt_time = 8 | |
| thumbnails = 400x400,800x480 | |
| [printer:Anycubic Photon HiTemp] | |
| absolute_correction = -0.0195 | |
| area_fill = 50 | |
| bed_custom_model = | |
| bed_custom_texture = | |
| bed_shape = 1.48x1.02,119.48x1.02,119.48x67.02,1.48x67.02 | |
| default_sla_material_profile = Prusa Orange Tough 0.05 | |
| default_sla_print_profile = 0.05 Normal | |
| display_height = 68.04 | |
| display_mirror_x = 1 | |
| display_mirror_y = 0 | |
| display_orientation = portrait | |
| display_pixels_x = 2560 | |
| display_pixels_y = 1440 | |
| display_width = 120.96 | |
| elefant_foot_compensation = 0.2 | |
| elefant_foot_min_width = 0.2 | |
| fast_tilt_time = 5 | |
| gamma_correction = 0 | |
| host_type = octoprint | |
| inherits = | |
| max_exposure_time = 120 | |
| max_initial_exposure_time = 300 | |
| max_print_height = 150 | |
| min_exposure_time = 1 | |
| min_initial_exposure_time = 1 | |
| print_host = | |
| printer_model = SL1 | |
| printer_notes = | |
| printer_settings_id = | |
| printer_technology = SLA | |
| printer_variant = default | |
| printer_vendor = | |
| printhost_apikey = | |
| printhost_cafile = | |
| relative_correction = 0.99544,1 | |
| slow_tilt_time = 8 | |
| thumbnails = 400x400,800x480 | |
| [printer:Hacksburg CR-10] | |
| bed_custom_model = | |
| bed_custom_texture = | |
| bed_shape = 0x0,390x0,390x390,0x390 | |
| before_layer_gcode = | |
| between_objects_gcode = | |
| color_change_gcode = M600 | |
| cooling_tube_length = 5 | |
| cooling_tube_retraction = 91.5 | |
| default_filament_profile = "" | |
| default_print_profile = | |
| deretract_speed = 40 | |
| end_gcode = M104 S0 ; turn off temperature\nM190 S0; turn off bed\nG28 X0 ; home X axis\nM84 ; disable motors\n | |
| extra_loading_move = -2 | |
| extruder_colour = "" | |
| extruder_offset = 0x0 | |
| gcode_flavor = marlin | |
| high_current_on_filament_swap = 0 | |
| host_type = octoprint | |
| inherits = | |
| layer_gcode = | |
| machine_limits_usage = emit_to_gcode | |
| machine_max_acceleration_e = 10000,5000 | |
| machine_max_acceleration_extruding = 1500,1250 | |
| machine_max_acceleration_retracting = 1500,1250 | |
| machine_max_acceleration_x = 1000,1000 | |
| machine_max_acceleration_y = 500,500 | |
| machine_max_acceleration_z = 500,200 | |
| machine_max_feedrate_e = 120,120 | |
| machine_max_feedrate_x = 500,200 | |
| machine_max_feedrate_y = 500,200 | |
| machine_max_feedrate_z = 12,12 | |
| machine_max_jerk_e = 2.5,2.5 | |
| machine_max_jerk_x = 10,10 | |
| machine_max_jerk_y = 10,10 | |
| machine_max_jerk_z = 0.2,0.4 | |
| machine_min_extruding_rate = 0,0 | |
| machine_min_travel_rate = 0,0 | |
| max_layer_height = 0 | |
| max_print_height = 380 | |
| min_layer_height = 0.07 | |
| nozzle_diameter = 0.4 | |
| parking_pos_retraction = 92 | |
| pause_print_gcode = M601 | |
| print_host = | |
| printer_model = | |
| printer_notes = | |
| printer_settings_id = | |
| printer_technology = FFF | |
| printer_variant = | |
| printer_vendor = | |
| printhost_apikey = | |
| printhost_cafile = | |
| remaining_times = 0 | |
| retract_before_travel = 2 | |
| retract_before_wipe = 0% | |
| retract_layer_change = 0 | |
| retract_length = 6 | |
| retract_length_toolchange = 10 | |
| retract_lift = 0 | |
| retract_lift_above = 0 | |
| retract_lift_below = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 20 | |
| silent_mode = 0 | |
| single_extruder_multi_material = 0 | |
| start_gcode = G28 ; home all axes\nM420S1;\nG1 Z5 F5000 ; lift nozzle\nM92 X80.2 Y80.056\nM900 K1.2 ; Linear advance | |
| template_custom_gcode = | |
| thumbnails = | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| variable_layer_height = 1 | |
| wipe = 0 | |
| z_offset = -0.1 | |
| [printer:Makerbot] | |
| bed_custom_model = | |
| bed_custom_texture = | |
| bed_shape = -150x-75,150x-75,150x75,-150x75 | |
| before_layer_gcode = | |
| between_objects_gcode = | |
| color_change_gcode = M600 | |
| cooling_tube_length = 5 | |
| cooling_tube_retraction = 91.5 | |
| default_filament_profile = "" | |
| default_print_profile = | |
| deretract_speed = 0 | |
| end_gcode = (**** End.gcode ****)\nM103 ;Turn extruder off\nM104 S0 ;Zero temperature\nM73 P100 ;End build progress\nG0 Z155 ;Send Z axis to bottom of machine\nM18 ;Disable stepper\nM104 S0 T0 ;Cool down the Right Extruder\nG162 X Y F2500 ;Home XY endstops\nM18 ;Disable stepper motors\nM70 P5 ( We Be Making Things!)\nM72 P1 ;Play Ta-Da song\n(**** end of End.gcode ****)\n | |
| extra_loading_move = -2 | |
| extruder_colour = "" | |
| extruder_offset = 0x0 | |
| gcode_flavor = makerware | |
| high_current_on_filament_swap = 0 | |
| host_type = octoprint | |
| inherits = | |
| layer_gcode = | |
| machine_limits_usage = emit_to_gcode | |
| machine_max_acceleration_e = 10000,5000 | |
| machine_max_acceleration_extruding = 1500,1250 | |
| machine_max_acceleration_retracting = 1500,1250 | |
| machine_max_acceleration_x = 9000,1000 | |
| machine_max_acceleration_y = 9000,1000 | |
| machine_max_acceleration_z = 500,200 | |
| machine_max_feedrate_e = 120,120 | |
| machine_max_feedrate_x = 500,200 | |
| machine_max_feedrate_y = 500,200 | |
| machine_max_feedrate_z = 12,12 | |
| machine_max_jerk_e = 2.5,2.5 | |
| machine_max_jerk_x = 10,10 | |
| machine_max_jerk_y = 10,10 | |
| machine_max_jerk_z = 0.2,0.4 | |
| machine_min_extruding_rate = 0,0 | |
| machine_min_travel_rate = 0,0 | |
| max_layer_height = 0 | |
| max_print_height = 200 | |
| min_layer_height = 0.07 | |
| nozzle_diameter = 0.4 | |
| parking_pos_retraction = 92 | |
| pause_print_gcode = M601 | |
| print_host = | |
| printer_model = | |
| printer_notes = | |
| printer_settings_id = | |
| printer_technology = FFF | |
| printer_variant = | |
| printer_vendor = | |
| printhost_apikey = | |
| printhost_cafile = | |
| remaining_times = 0 | |
| retract_before_travel = 2 | |
| retract_before_wipe = 0% | |
| retract_layer_change = 0 | |
| retract_length = 2 | |
| retract_length_toolchange = 10 | |
| retract_lift = 0 | |
| retract_lift_above = 0 | |
| retract_lift_below = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 40 | |
| silent_mode = 1 | |
| single_extruder_multi_material = 0 | |
| start_gcode = (**** Start.gcode for Replicator 2 ****)\nM103 ;disable RPM\nM73 P0 ;enable build progress\nG21 ;set units to mm\nG90 ;set positioning to absolute\n(**** begin homing ****)\nG162 X Y F2500 ;home XY axes maximum\nG161 Z F1100 ;home Z axis minimum\nG92 Z-5 ;set Z to -5\nG1 Z0.0 ;move Z to "0"\nG161 Z F100 ;home Z axis minimum\nM132 X Y Z A B ;Recall stored home offsets for XYZAB axis\n(**** end homing ****)\nG1 X-141 Y-74 Z75 F3300.0 ;move to waiting position\nG130 X20 Y20 Z20 A20 B20 ;Lower stepper Vrefs while heating\nM6 T0 ;wait for toolhead, and HBP to reach temperature\nM70 P5 (We Be Making Things!)\nG130 X127 Y127 Z40 A127 B127 ;Set Stepper motor Vref to defaults\nM108 R3.0 T0\nG0 X-141 Y-74 ;Position Nozzle\nG0 Z1 ;Move above plate\nG1 Z0.3 ;Position Height\nM108 R5.0 ;Set Extruder Speed\nM101 ;Start Extruder\nG4 P3000 ;Create Anchor\nG1 X-137 Y-70 Z0.1 F1000.0 ;Slow wipe\nG0 Z0.3 ;and lift\n(**** end of Start.gcode ****)\n | |
| template_custom_gcode = | |
| thumbnails = | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| variable_layer_height = 1 | |
| wipe = 0 | |
| z_offset = 0 | |
| [presets] | |
| print = Normal 0.2 | |
| sla_print = 0.025 Normal | |
| sla_material = Elegoo Gray | |
| printer = Anycubic Photon | |
| filament = PLA No Cool |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment