Created
November 20, 2018 19:32
-
-
Save NF3RN0/c2cc2e160ed19a064672be1e99f5d5c5 to your computer and use it in GitHub Desktop.
rpi-open-firmware boot messages on a Raspberry PI 3
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| Booting Raspberry Pi.... | |
| Copyright 2016-2017 rpi-open-firmware authors | |
| BUILDATE : Nov 20 2018 04:41:15 | |
| __cxx_init: calling 5 static constructors (0x14000 - 0x14014) ... | |
| BCM2708UsbPhy::registerDriver(): driver registered on platform IO plane | |
| BCM2708ArmControl::registerDriver(): driver registered on platform IO plane | |
| BCM2708PLLB::init(): PLLB VCO registered | |
| BCM2708PLLB::registerDriver(): driver registered on platform IO plane | |
| BCM2708Gpio::registerDriver(): driver registered on platform IO plane | |
| [SDRAM:sdram_init]: (0) SD_CS = 0x794200 | |
| [SDRAM:switch_to_cprman_clock]: switching sdram to cprman clock (src=1, div=1), waiting for busy (4011) ... | |
| [SDRAM:switch_to_cprman_clock]: busy set, switch complete! | |
| [SDRAM:reset_phy]: reset_phy: resetting SDRAM PHY ... | |
| [SDRAM:reset_phy]: reset_phy: resetting DPHY CTRL ... | |
| [SDRAM:reset_phy_dll]: resetting aphy and dphy dlls ... | |
| [SDRAM:reset_phy_dll]: waiting for dphy master dll to lock ... | |
| [SDRAM:reset_phy_dll]: dphy master dll locked! | |
| [SDRAM:sdram_init]: waiting for SDUP (210242) ... | |
| [SDRAM:sdram_init]: SDRAM controller has arrived! (218E42) | |
| [SDRAM:calibrate_pvt_early]: DPHY_CSR_DQ_PAD_DRV_SLEW_CTRL = 0x223 | |
| [SDRAM:calibrate_pvt_early]: waiting for address PVT calibration ... | |
| [SDRAM:calibrate_pvt_early]: waiting for data PVT calibration ... | |
| [SDRAM:calibrate_pvt_early]: waiting for SDRAM calibration command ... | |
| [SDRAM:sdram_init]: SDRAM Type: Elpida 1GB LPDDR2 (BC=0x58) | |
| [SDRAM:reset_with_timing]: waiting for SDRAM controller to go down (218E4A) ... | |
| [SDRAM:reset_with_timing]: SDRAM controller down! | |
| [SDRAM:reset_with_timing]: SDRAM clock disabled! | |
| [SDRAM:reset_with_timing]: waiting for master ddr pll to lock ... | |
| [SDRAM:reset_with_timing]: master ddr pll locked! | |
| [SDRAM:reset_with_timing]: SDRAM Addressing Mode: Bank=3 Row=3 Col=3 SB=0xFF | |
| [SDRAM:reset_phy_dll]: resetting aphy and dphy dlls ... | |
| [SDRAM:reset_phy_dll]: waiting for dphy master dll to lock ... | |
| [SDRAM:reset_phy_dll]: dphy master dll locked! | |
| [SDRAM:reset_with_timing]: waiting for address dll to lock ... | |
| [SDRAM:reset_with_timing]: address dll locked! | |
| [SDRAM:selftest]: Starting self test ... | |
| [SDRAM:selftest_at]: Testing region at 0xC0000000 ... | |
| [SDRAM:selftest_at]: Testing region at 0xCFF00000 ... | |
| [SDRAM:selftest_at]: Testing region at 0xDFF00000 ... | |
| [SDRAM:selftest_at]: Testing region at 0xEFF00000 ... | |
| [SDRAM:selftest_at]: Testing region at 0xFFF00000 ... | |
| [SDRAM:selftest]: Self test successful! | |
| SDRAM initialization completed successfully! | |
| BCM2708PowerDomainUSB::stop(): stopping ... | |
| BCM2708PowerDomainUSB::stop(): stopped | |
| BCM2708PowerDomainImage::powerOn(): powering on, current PM_IMAGE state: 0x1000 | |
| BCM2708PowerDomainImage::beginPowerUpSequence(): starting power up sequence ... | |
| BCM2708PowerDomainImage::waitForPOWOK(): waiting for POWOK ... | |
| BCM2708PowerDomainImage::waitForPOWOK(): got POWOK with CFG=0x10000 | |
| BCM2708PowerDomainImage::powerOn(): stopping power up sequence ... | |
| BCM2708PowerDomainImage::beginPowerUpSequence(): starting power up sequence ... | |
| BCM2708PowerDomainImage::waitForPOWOK(): waiting for POWOK ... | |
| BCM2708PowerDomainImage::waitForPOWOK(): got POWOK with CFG=0x30000 | |
| BCM2708PowerDomainImage::completePowerUpSequence(): waiting for MRDONE ... | |
| BCM2708PowerDomainImage::resetPeripheralsUngated(): calling v16mov gated ... | |
| BCM2708PowerDomainImage::resetPeripheralsUngated(): ungating and resetting ... | |
| BCM2708PowerDomainImage::resetPeripheralsUngated(): done | |
| BCM2708PowerDomainImage::start(): CM_PERIICTL = 0x40 | |
| BCM2708PowerDomainImage::start(): CM_PERIIDIV = 0x0 | |
| BCM2708PowerDomainImage::start(): PM_IMAGE = 0x3107F | |
| BCM2708PowerDomainImage::start(): started | |
| BCM2708PowerDomainUSB::start(): starting ... | |
| BCM2708PowerDomainUSB::start(): started | |
| BCM2708UsbPhy::start(): starting ... | |
| BCM2708UsbPhy::start(): LAN reset | |
| BCM2708UsbPhy::start(): started | |
| BCM2708ArmControl::start(): starting ... | |
| BCM2708ArmControl::loadInitialCode(): copied 57412 bytes to 0xC0000000! | |
| BCM2708ArmControl::start(): original memstart: 0xEA000039 | |
| BCM2708ArmControl::start(): mapped VC 0xC0000000 to ARM 0x0 | |
| BCM2708ArmControl::start(): mapped peripherals VC 0x7E000000 to ARM 0x3F000000 | |
| BCM2708ArmControl::start(): ARM ID: 0x364D5241 C0: 0x0 | |
| BCM2708ArmControl::start(): using C0: 0xA04B | |
| BCM2708ArmControl::setupClock(): initializing PLLB ... | |
| BCM2708PLLB::setDigValues(): setting DIG values for this VCO ... | |
| BCM2708ArmControl::setupClock(): KAIP = 0x228 | |
| BCM2708ArmControl::setupClock(): MULTI = 0x613277 | |
| BCM2708ArmControl::setupClock(): ARM clock succesfully initialized! | |
| BCM2708PowerDomainARM::start(): starting ... | |
| BCM2708PowerDomainARM::powerOn(): powering on (rstnMask=0xFFFFFFBF) ... | |
| BCM2708PowerDomainARM::beginPowerUpSequence(): starting power up sequence ... | |
| BCM2708PowerDomainARM::waitForPOWOK(): waiting for POWOK ... | |
| BCM2708PowerDomainARM::waitForPOWOK(): got POWOK with CFG=0x0 | |
| BCM2708PowerDomainARM::completePowerUpSequence(): waiting for MRDONE ... | |
| BCM2708PowerDomainARM::powerOn(): domain powered on succesfully | |
| BCM2708PowerDomainARM::start(): started | |
| BCM2708ArmControl::bridgeStart(): setting up async bridge ... | |
| BCM2708PowerDomainARM::setReset(): setting RSTN bits to 0x40 ... | |
| BCM2708ArmControl::bridgeCycleBresp(): cycling through bresp bits ... | |
| BCM2708PowerDomainARM::setReset(): setting RSTN bits to 0x40 ... | |
| BCM2708ArmControl::bridgeStart(): starting async bridge now! | |
| BCM2708ArmControl::bridgeStart(): bridge init done, PM_PROC is now: 0x107F! | |
| Starting IPC monitor ... | |
| tinuing boot from here ... | |
| [BRINGUP:main]: Firmware data: SDRAM_SIZE=0, VPU_CPUID=0x4000140 | |
| [BRINGUP:main]: Security extensions are supported! | |
| [BRINGUP:main]: Execution mode: Supervisor | |
| [BRINGUP:heap_init]: Initializing heap at 0x24000 with size 0x100000 | |
| __cxx_init: calling 4 static constructors (0xE000 - 0xE010) ... | |
| [EMMC:restart_controller]: hcfg 0xE, cdiv 0x0, edm 0x8C01, hsts 0x0 | |
| [EMMC:restart_controller]: Restarting the eMMC controller ... | |
| [EMMC:configure_pinmux]: waiting for pinmux pull update ... | |
| [EMMC:configure_pinmux]: waiting for pinmux clock update ... | |
| [EMMC:configure_pinmux]: ok ... | |
| [EMMC:configure_pinmux]: pinmux configured for aux0 | |
| [EMMC:reset]: resetting controller ... | |
| [EMMC:query_voltage_and_type]: waiting for SD (0xff8000) ... | |
| [EMMC:query_voltage_and_type]: SD card has arrived! | |
| [EMMC:query_voltage_and_type]: This is an SDHC card! | |
| [EMMC:identify_card]: identifying card ... | |
| [EMMC:identify_card]: RCA = 0x7 | |
| [EMMC:init_card]: Detected SD card: | |
| Product : SD08G | |
| CSD : Ver 2.0 | |
| Capacity: 15564800 | |
| Size : 15199 | |
| BlockLen: 0x200 | |
| [EMMC:init_card]: Card initialization complete: SD08G 3504MB SDHC Card | |
| [EMMC:init_card]: Identification complete, changing clock to 50MHz for data mode ... | |
| [EMMC:BCM2708SDHost]: eMMC driver sucessfully started! | |
| [MBRDISK:read_mbr]: Reading master boot record ... | |
| [MBRDISK:read_mbr]: MBR contents: | |
| 0: FAT32 at:8192 size:2097152 | |
| 1: Linux (ext2/ext3) at:2105344 size:13459456 | |
| 2: <Unknown> at:0 size:0 | |
| 3: <Unknown> at:0 size:0 | |
| [MBRDISK:MbrImpl]: Disk ready! | |
| [LDR:LoaderImpl]: Mounting boot partitiion ... | |
| [LDR:LoaderImpl]: Boot partition mounted! | |
| [LDR:read_file]: cmdline.txt: reading 56 bytes to 0x24E90 (allocated=1) ... | |
| [LDR:LoaderImpl]: kernel cmdline: console=ttyAMA0,115200 elevator=deadline rdinit=/bin/sh | |
| [LDR:read_file]: rpi.dtb: reading 15992 bytes to 0xF000000 (allocated=0) ... | |
| [LDR:load_fdt]: FDT loaded at F000000 | |
| [LDR:load_fdt]: (valid) fdt loaded at 0xF000000 | |
| [LDR:read_file]: zImage: reading 4076016 bytes to 0x2000000 (allocated=0) ... | |
| [LDR:LoaderImpl]: zImage loaded at 0x2000000 | |
| [LDR:LoaderImpl]: Flushing.... | |
| [EMMC:stop]: flushing fifo ... | |
| [EMMC:stop]: asking card to enter idle state ... | |
| [EMMC:stop]: stopping sdhost controller driver ... | |
| [EMMC:stop]: powering down controller ... | |
| [EMMC:stop]: resetting state machine ... | |
| [LDR:LoaderImpl]: Jumping to the Linux kernel... | |
| Uncompressing Linux... done, booting the kernel. | |
| [ 0.000000] Booting Linux on physical CPU 0x0 | |
| [ 0.000000] Initializing cgroup subsys cpuset | |
| [ 0.000000] Initializing cgroup subsys cpu | |
| [ 0.000000] Initializing cgroup subsys cpuacct | |
| [ 0.000000] Linux version 4.4.31-v7+ (root@vc4-build-11-19-18) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9) ) #1 Tue Nov 20 04:51:54 UTC 2018 | |
| [ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d | |
| [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache | |
| [ 0.000000] Machine model: Raspberry Pi 3 Model B | |
| [ 0.000000] cma: Reserved 8 MiB at 0x2f800000 | |
| [ 0.000000] Memory policy: Data cache writeback | |
| [ 0.000000] ------------[ cut here ]------------ | |
| [ 0.000000] WARNING: CPU: 0 PID: 0 at arch/arm/kernel/devtree.c:157 arm_dt_init_cpu_maps+0x140/0x180() | |
| [ 0.000000] DT /cpu 2 nodes greater than max cores 1, capping them | |
| [ 0.000000] Modules linked in: | |
| [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.4.31-v7+ #1 | |
| [ 0.000000] Hardware name: BCM2709 | |
| [ 0.000000] [<80016d6c>] (unwind_backtrace) from [<80013c54>] (show_stack+0x20/0x24) | |
| [ 0.000000] [<80013c54>] (show_stack) from [<8029657c>] (dump_stack+0x24/0x28) | |
| [ 0.000000] [<8029657c>] (dump_stack) from [<80023050>] (warn_slowpath_common+0x94/0xc0) | |
| [ 0.000000] [<80023050>] (warn_slowpath_common) from [<800230bc>] (warn_slowpath_fmt+0x40/0x48) | |
| [ 0.000000] [<800230bc>] (warn_slowpath_fmt) from [<805887f8>] (arm_dt_init_cpu_maps+0x140/0x180) | |
| [ 0.000000] [<805887f8>] (arm_dt_init_cpu_maps) from [<80588374>] (setup_arch+0x718/0x780) | |
| [ 0.000000] [<80588374>] (setup_arch) from [<80584a14>] (start_kernel+0x94/0x3bc) | |
| [ 0.000000] [<80584a14>] (start_kernel) from [<00008074>] (0x8074) | |
| [ 0.000000] ---[ end trace cb88537fdc8fa200 ]--- | |
| [ 0.000000] CPU: All CPU(s) started in SVC mode. | |
| [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 194879 | |
| [ 0.000000] Kernel command line: console=ttyAMA0,115200 elevator=deadline rdinit=/bin/sh | |
| [ 0.000000] | |
| [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) | |
| [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) | |
| [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) | |
| [ 0.000000] Memory: 762428K/786428K available (4360K kernel code, 285K rwdata, 1252K rodata, 1448K init, 568K bss, 15808K reserved, 8192K cma-reserved) | |
| [ 0.000000] Virtual kernel memory layout: | |
| [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) | |
| [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) | |
| [ 0.000000] vmalloc : 0xb0800000 - 0xff800000 (1264 MB) | |
| [ 0.000000] lowmem : 0x80000000 - 0xb0000000 ( 768 MB) | |
| [ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB) | |
| [ 0.000000] .text : 0x80008000 - 0x80583408 (5614 kB) | |
| [ 0.000000] .init : 0x80584000 - 0x806ee000 (1448 kB) | |
| [ 0.000000] .data : 0x806ee000 - 0x80735458 ( 286 kB) | |
| [ 0.000000] .bss : 0x80738000 - 0x807c61d8 ( 569 kB) | |
| [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 | |
| [ 0.000000] NR_IRQS:16 nr_irqs:16 16 | |
| [ 0.000000] Architected cp15 timer(s) running at 19.20MHz (virt). | |
| [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns | |
| [ 0.000008] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns | |
| [ 0.000026] Switching to timer-based delay loop, resolution 52ns | |
| [ 0.000252] Console: colour dummy device 80x30 | |
| [ 0.000280] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000) | |
| [ 0.000300] pid_max: default: 32768 minimum: 301 | |
| [ 0.000578] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) | |
| [ 0.000595] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) | |
| [ 0.001446] Disabling cpuset control group subsystem | |
| [ 0.001476] Initializing cgroup subsys io | |
| [ 0.001502] Initializing cgroup subsys memory | |
| [ 0.001537] Initializing cgroup subsys devices | |
| [ 0.001558] Initializing cgroup subsys freezer | |
| [ 0.001590] CPU: Testing write buffer coherency: ok | |
| [ 0.001639] ftrace: allocating 14415 entries in 43 pages | |
| [ 0.039564] Setting up static identity map for 0x8200 - 0x8234 | |
| [ 0.040561] devtmpfs: initialized | |
| [ 0.048037] VFP support v0.3: not present | |
| [ 0.048248] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns | |
| [ 0.049028] pinctrl core: initialized pinctrl subsystem | |
| [ 0.054364] DMA: preallocated 4096 KiB pool for atomic coherent allocations | |
| [ 0.060052] bcm2709: Mini UART enabled | |
| [ 0.060088] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. | |
| [ 0.060099] hw-breakpoint: maximum watchpoint size is 8 bytes. | |
| [ 0.060187] Serial: AMBA PL011 UART driver | |
| [ 0.060330] uart-pl011 3f201000.uart: could not find pctldev for node /soc/gpio@7e200000/uart0_pins, deferring probe | |
| [ 0.098721] SCSI subsystem initialized | |
| [ 0.098950] usbcore: registered new interface driver usbfs | |
| [ 0.099053] usbcore: registered new interface driver hub | |
| [ 0.099138] usbcore: registered new device driver usb | |
| [ 0.099649] clocksource: Switched to clocksource arch_sys_counter | |
| [ 0.142205] FS-Cache: Loaded | |
| [ 0.142434] CacheFiles: Loaded | |
| [ 0.273521] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available | |
| [ 0.274437] futex hash table entries: 256 (order: -1, 3072 bytes) | |
| [ 0.286386] VFS: Disk quotas dquot_6.6.0 | |
| [ 0.286687] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) | |
| [ 0.291259] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) | |
| [ 0.291410] io scheduler noop registered | |
| [ 0.291430] io scheduler deadline registered (default) | |
| [ 0.291754] io scheduler cfq registered | |
| [ 0.293170] of_serial: probe of 3f215040.uart failed with error -28 | |
| [ 1.208421] bcm2835-rng 3f104000.rng: hwrng registered | |
| [ 1.208558] vc-mem: phys_addr:0x00000000 mem_base=0x00000000 mem_size:0x00000000(0 MiB) | |
| [ 1.222959] brd: module loaded | |
| [ 1.230269] loop: module loaded | |
| [ 1.230516] dwc_otg: version 3.00a 10-AUG-2012 (platform bus) | |
| [ 1.430796] Core Release: 2.80a | |
| [ 1.430811] Setting default values for core params | |
| [ 1.430845] Finished setting default values for core params | |
| [ 1.631248] Using Buffer DMA mode | |
| [ 1.631260] Periodic Transfer Interrupt Enhancement - disabled | |
| [ 1.631270] Multiprocessor Interrupt Enhancement - disabled | |
| [ 1.631281] OTG VER PARAM: 0, OTG VER FLAG: 0 | |
| [ 1.631307] Dedicated Tx FIFOs mode | |
| [ 1.632485] WARN::dwc_otg_hcd_init:1047: FIQ DMA bounce buffers: virt = 0xafc04000 dma = 0xefc04000 len=9024 | |
| [ 1.632519] FIQ FSM acceleration enabled for : | |
| [ 1.632519] Non-periodic Split Transactions | |
| [ 1.632519] Periodic Split Transactions | |
| [ 1.632519] High-Speed Isochronous Endpoints | |
| [ 1.632519] Interrupt/Control Split Transaction hack enabled | |
| [ 1.632589] WARN::hcd_init_fiq:413: FIQ on core 0 at 0x80382694 | |
| [ 1.632604] WARN::hcd_init_fiq:414: FIQ ASM at 0x80382940 length 36 | |
| [ 1.632620] WARN::hcd_init_fiq:439: MPHI regs_base at 0xb0898000 | |
| [ 1.632672] dwc_otg 3f980000.usb: DWC OTG Controller | |
| [ 1.632713] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1 | |
| [ 1.632769] dwc_otg 3f980000.usb: irq 62, io mem 0x00000000 | |
| [ 1.632826] Init: Port Power? op_state=1 | |
| [ 1.632835] Init: Power Port (0) | |
| [ 1.633016] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 | |
| [ 1.633034] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 | |
| [ 1.633050] usb usb1: Product: DWC OTG Controller | |
| [ 1.633064] usb usb1: Manufacturer: Linux 4.4.31-v7+ dwc_otg_hcd | |
| [ 1.633078] usb usb1: SerialNumber: 3f980000.usb | |
| [ 1.633772] hub 1-0:1.0: USB hub found | |
| [ 1.633818] hub 1-0:1.0: 1 port detected | |
| [ 1.634544] usbcore: registered new interface driver usb-storage | |
| [ 1.634756] mousedev: PS/2 mouse device common for all mice | |
| [ 1.634972] sdhci: Secure Digital Host Controller Interface driver | |
| [ 1.634982] sdhci: Copyright(c) Pierre Ossman | |
| [ 1.635278] sdhost: log_buf @ afc03000 (efc03000) | |
| [ 1.655398] mmc0: unable to initialise DMA channel. Falling back to PIO | |
| [ 1.709675] mmc0: sdhost-bcm2835 loaded - DMA disabled | |
| [ 1.709859] sdhci-pltfm: SDHCI platform and OF driver helper | |
| [ 1.710133] ledtrig-cpu: registered to indicate activity on CPUs | |
| [ 1.710277] hidraw: raw HID events driver (C) Jiri Kosina | |
| [ 1.710505] usbcore: registered new interface driver usbhid | |
| [ 1.710515] usbhid: USB HID core driver | |
| [ 1.733097] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2 | |
| [ 1.942630] mmc0: host does not support reading read-only switch, assuming write-enable | |
| [ 1.956320] mmc0: new high speed SDHC card at address 0007 | |
| [ 2.012334] mmcblk0: mmc0:0007 SD08G 7.42 GiB | |
| [ 2.019623] mmcblk0: p1 p2 | |
| [ 2.538095] console [ttyAMA0] enabled | |
| [ 2.542174] of_cfs_init | |
| [ 2.544679] of_cfs_init: OK | |
| [ 2.548107] Warning: unable to open an initial console. | |
| [ 2.555284] Freeing unused kernel memory: 1448K (80584000 - 806ee000) | |
| [ 2.563728] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000000 | |
| [ 2.563728] | |
| [ 2.572856] CPU: 0 PID: 1 Comm: sh Tainted: G W 4.4.31-v7+ #1 | |
| [ 2.579716] Hardware name: BCM2709 | |
| [ 2.583135] [<80016d6c>] (unwind_backtrace) from [<80013c54>] (show_stack+0x20/0x24) | |
| [ 2.590881] [<80013c54>] (show_stack) from [<8029657c>] (dump_stack+0x24/0x28) | |
| [ 2.598105] [<8029657c>] (dump_stack) from [<800d3ee0>] (panic+0x9c/0x1f0) | |
| [ 2.604982] [<800d3ee0>] (panic) from [<80025274>] (complete_and_exit+0x0/0x2c) | |
| [ 2.612292] [<80025274>] (complete_and_exit) from [<80025310>] (do_group_exit+0x50/0xc0) | |
| [ 2.620379] [<80025310>] (do_group_exit) from [<800253a0>] (__wake_up_parent+0x0/0x30) | |
| [ 2.628294] [<800253a0>] (__wake_up_parent) from [<8000f8c0>] (ret_fast_syscall+0x0/0x1c) | |
| [ 2.636463] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000000 | |
| [ 2.636463] |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment